This commit looks like a cleanup but in fact by causing the core to go
down some simplified code paths for noop regulators it avoids a boot
time crash for msm8974 platforms which was introduced in v4.7. It has
been in -next for a while, the issues in mainline for these platforms
weren't flagged up to me until yesterday (I think it took some time to
figure out what was going wrong).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXhQPCAAoJECTWi3JdVIfQZAQH/AqXEFh1oZywnf6daYraLUfd
7W8OXf4nLywazeVaHBaa3hCSrIT4CYiCKcxB8vDm1//nFVcsRJnlxWQxw62/A8dx
u3ovQjwM1UfTsrR68WmnR47RO71jruex+gtISFCbYvE8NQqPPDHBlA9Q6B4VTd+n
IcoS8fdUc6QD4M+yveUcsLcppROpCm7/sba49v2qJMWZ62h2CSpZyO7ImYwkmalt
PJvmkKF7Vl/pnpiWMpGByMvz5o4jDNtaZjVr9wFF3T7otlC62sLi16AnIo+zmWam
+T9nI+ltZPtV/C46nfXyAPEqtmPyLSueVKpNgTflJPEPKUanXLWpIFZu7+MHpnI=
=nwMu
-----END PGP SIGNATURE-----
Merge tag 'qcom-smd-list-voltage' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"Fix qcom-smd list voltage issues for msm8974
This commit looks like a cleanup but in fact by causing the core to go
down some simplified code paths for noop regulators it avoids a boot
time crash for msm8974 platforms which was introduced in v4.7. It has
been in -next for a while, the issues in mainline for these platforms
weren't flagged up to me until yesterday (I think it took some time to
figure out what was going wrong)"
* tag 'qcom-smd-list-voltage' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom_smd: Remove list_voltage callback for rpm_smps_ldo_ops_fixed
SD4 regulator is not registered with regulator core
framework in probe as there is no support in MAX77620 PMIC,
removing SD4 entry from MAX77620 regulator information list
and checking for valid regulator information data before
configuring FPS source and FPS power up/down period to avoid
NULL pointer exception if regulator not registered with core.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bypass support was added in commit d38018f201 ("regulator: anatop: Add
bypass support to digital LDOs"). A check for valid voltage selectors was
added in commit da0607c8df ("regulator: anatop: Fail on invalid voltage
selector") but it also discards all regulators that are in bypass mode. Add
check for the bypass setting. Errors below were seen on a Variscite mx6
board.
anatop_regulator 20c8000.anatop:regulator-vddcore@140: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddcore@140 failed with error -22
anatop_regulator 20c8000.anatop:regulator-vddsoc@140: Failed to read a valid default voltage selector.
anatop_regulator: probe of 20c8000.anatop:regulator-vddsoc@140 failed with error -22
Fixes: da0607c8df ("regulator: anatop: Fail on invalid voltage selector")
Signed-off-by: Mika Båtsman <mbatsman@mvista.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use regulator_list_voltage_linear_range in rpm_smps_ldo_ops_fixed is
wrong because it is used for fixed regulator without any linear range.
The rpm_smps_ldo_ops_fixed is used for pm8941_lnldo which has fixed_uV
set and n_voltages = 1. In this case, regulator_list_voltage() can return
rdev->desc->fixed_uV without .list_voltage implementation.
Fixes: 3bfbb4d1a4 ("regulator: qcom_smd: add list_voltage callback")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to list_voltage callback, so that consumers
like mmc core, can get information of supported voltage range.
Without this patch there is no way for mmc core to know this voltage range.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
After "regulator: qcom_smd: add list_voltage callback" patch adding
pm8941 lnldo regulators would bug on list_voltages as it is a fixed
regulator without any linear range.
This patch fixes that issue by adding dedicated ops for pm8941 lnldo
without list_voltages callback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org # v4.6
This patch adds support to list_voltage callback, so that consumers
like mmc core, can get information of supported voltage range.
Without this patch there is no way for mmc core to know this voltage range.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org # v4.6
According to the datasheet:
SLEW Register(Address = 07h)
b7 b6 b5 b4 b3 b2 b1 b0
48mV/us 42mV/us 36mV/us 30mV/us 24mV/us 18mV/us 12mV/us 6mV/us
Current code does not set correct slew rate in some cases:
e.g. Assume ramp_delay is 10000, current code sets slew register to 6mV/us.
Fix the logic to set slew register.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A common simplified DT parsing code for regulators was introduced in
commit a0c7b164ad ("regulator: of: Provide simplified DT parsing
method")
While at it also added RK8XX_DESC and RK8XX_DESC_SWITCH macros for the
regulator_desc struct initialization. This just makes the driver more compact.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators set consists of 2 BUCKs and 2 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components. The ramp delay is configurable
for both BUCKs.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just dereference match->of_node once instead of using match->of_node.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stop the palmas regulator driver from imagining that the allocations
will always succeed. Since regulator dt nodes are optional in nature and
can be described in downstream drivers via platform data, continue to
maintain code flow as prior when of node is not found.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Converting dt to platform data logic involves picking up information
that is unique per regulator, however we can improve readability of
the code by allocating and referencing pdata->reg_init[idx] once in
the loop.
While at it, use sizeof(*pointer) when allocating pointer. This allows
for structure name changes with minimal code change.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Converting dt to platform data logic involves picking up information
that is unique per regulator, however we can improve readability of
the code by dereferencing ddata->palmas_matches[idx] once in the loop.
While at it fix reuse of generic palmas_matches common variable
while reporting error for a specific regulator (which may be from
65917/palmas list).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PWM framework has clarified the concept of reference PWM config (the
platform dependent config retrieved from the DT or the PWM lookup table)
and real PWM state.
Use pwm_get_args() when the PWM user wants to retrieve this reference
config and not the current state.
This is part of the rework allowing the PWM framework to support
hardware readout and expose real PWM state even when the PWM has just
been requested (before the user calls pwm_config/enable/disable()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The enable time for buck regulators was not configured but actually is
essential: consumers, like usb3503, doing hard reset (regulator off/on)
should wait for the regulator to settle.
Configure the enable time according to datasheet.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The maximum supported voltage for ldo_io# is 3.3V, but on cold
boot the selector comes up at 0x1f, which maps to 3.8V.
This causes _regulator_get_voltage() to fail with -EINVAL which
causes regulator registration to fail when constrains are used:
[ 1.467788] vcc-touchscreen: failed to get the current voltage(-22)
[ 1.474209] axp20x-regulator axp20x-regulator: Failed to register ldo_io1
[ 1.483363] axp20x-regulator: probe of axp20x-regulator failed with error -22
This commits makes the axp20x regulator driver accept the 0x1f register
value, fixing this.
The datasheet does not guarantee reliable operation above 3.3V, so on
boards where this regulator is used the regulator-max-microvolt setting
must be 3.3V or less.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO_REG3 descriptor is using linear_ranges.
Add and use proper ops for LDO_REG3.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to set_machine_constraints() in regulator_register(), will
attempt to get the voltage for the regulator. If a regulator is in
bypass will fail to get the voltage (ie. it's bypass voltage) and
hence register the regulator, because the supply for the regulator has
not been resolved yet.
To fix this, add a call to regulator_resolve_supply() before we call
set_machine_constraints(). If the call to regulator_resolve_supply()
fails, rather than returning an error at this point, allow the
registration of the regulator to continue because for some regulators
resolving the supply at this point may not be necessary and it will be
resolved later as more regulators are added. Furthermore, if the supply
is still not resolved for a bypassed regulator, this will be detected
when we attempt to get the voltage for the regulator and an error will
be propagated at this point.
If a bypassed regulator does not have a supply when we attempt to get
the voltage, rather than returing -EINVAL, return -EPROBE_DEFER instead
to allow the registration of the regulator to be deferred and tried
again later.
Please note that regulator_resolve_supply() will call
regulator_dev_lookup() which may acquire the regulator_list_mutex. To
avoid any deadlocks we cannot hold the regulator_list_mutex when calling
regulator_resolve_supply(). Therefore, rather than holding the lock
around a large portion of the registration code, just hold the lock when
aquiring any GPIOs and setting up supplies because these sections may
add entries to the regulator_map_list and regulator_ena_gpio_list,
respectively.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The minium voltage of 1800mV is a copy and paste error from the axp20x
regulator info. The correct minimum voltage for the ldo_io regulators
on the axp22x is 700mV.
Fixes: 1b82b4e4f9 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When commit b554e14506 ("regulator: tps65917/palmas: Add bypass
ops for LDOs with bypass capability") introduced bypass capability
to palmas regulator, it went with the assumption that regulator
regmap helpers just check val against the bypass_mask.
Unfortunately, this ignored the explicit "on" and "off" values when
the register value is masked with bypass_mask in commit ca5d1b3524
("regulator: helpers: Modify helpers enabling multi-bit control").
With the recent commit dd1a571dae ("regulator: helpers: Ensure
bypass register field matches ON value"), this issue gets highlighted
and fails tps65917/palmas based platforms which need regulators/ldos
that have bypass capability.
Introduce the bypass_on value appropriately for tps65917/palmas
regulator.
Fixes: b554e14506 ("regulator: tps65917/palmas: Add bypass ops for LDOs with bypass capability")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current linear voltage range for the LDO4 regulator found in the APX20X
PMICs assumes that the voltage is linear between 2.5 and 3.1V.
However, the PMIC can output up to 3.3V on that regulator by skipping the
2.6V and 2.9V steps.
Fix the ranges to read and set the proper voltages.
Fixes: 13d57e6435 ("regulator: axp20x: Use linear voltage ranges for AXP20X LDO4")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
After removing all uses of the range operations in a recent patch,
we get a warning about the symbol not being referenced anywhere:
drivers/regulator/rk808-regulator.c:306:29: 'rk808_reg_ops_ranges' defined but not used
This removes the now-unused structure along with the
rk808_set_suspend_voltage_range function that is only referenced from
rk808_reg_ops_ranges.
Fixes: afcd666d9d ("regulator: rk808: remove linear range definitions with a single range")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To make the code more compat and centralized, this patch add a
unified function - regulator_ops_is_valid. So we can add
some extra checking code easily later.
Signed-off-by: WEN Pingbo <pingbo.wen@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was using only linear ranges. Now we remove linear range
definitions with a single range. So we have to add an ops struct for
ranges and adjust all other ops functions accordingly.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Maxim advertised the ramp rate of the rail with some recommended
design specification like output capacitance of rail should be
2.2uF. This make sure that current change in the rail is within
maximum current limit and hence meet the advertised ramp rate.
If there is variation in design which causes the rail current to
change more that maximum current limit then device applies the
current limit. In this case, ramp rate is different than advertised
ramp rate.
Add device specific settings for ramp rate which need to be configure
on device register when measure ramp rate on platform is deviated from
advertised ramp rate. In this case, all delay time calculation for
voltage change is done with measured ramp rate and device ramp rate
is used for configuring the device register.
If measured ramp rate in the platform is same as advertised ramp rate
then regulator-ramp-delay is used for the device register configuration
and ramp time calculation for voltage change.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When checking bypass state for a regulator, we check to see if any bits
in the bypass mask are set. For most cases this is fine because there is
typically, only a single bit used to determine if the regulator is in
bypass. However, for some regulators, such as LDO6 on AS3722, the bypass
state is indicate by a value rather than a single bit. Therefore, when
checking the bypass state, check that the bypass field matches the ON
value.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The public functions to acquire a regulator, such as regulator_get(),
internally look-up the regulator from the list of regulators that have
been registered with the regulator device class. The registration of
a new regulator with the regulator device class happens before the
regulator has been completely setup. Therefore, it is possible that
the regulator could be acquired before it has been setup successfully.
To avoid this move the device registration of the regulator to the end
of the regulator setup and update the error exit path accordingly.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During the resolution of a regulator's supply, we may attempt to enable
the supply if the regulator itself is already enabled. If enabling the
supply fails, then we will call _regulator_put() for the supply.
However, the pointer to the supply has not been cleared for the
regulator and this will cause a crash if we then unregister the
regulator and attempt to call regulator_put() a second time for the
supply. Fix this by clearing the supply pointer if enabling the supply
after fails when resolving the supply for a regulator.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function regulator_register_resolve_supply() is called from the
context of class_for_each_dev() (during the regulator registration) to
resolve any supplies added. regulator_register_resolve_supply() will
return an error if a regulator's supply cannot be resolved and this will
terminate the loop in class_for_each_dev(). This means that we will not
attempt to resolve any other supplies after one has failed. Hence, this
may delay the resolution of other regulator supplies until the failing
one itself can be resolved.
Rather than terminating the loop early, don't return an error code and
keep attempting to resolve any other supplies for regulators that have
been registered.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are debugfs entries for voltage and current, but not for
the constraint flags. It's useful for debugging to be able to
see what these flags are so this patch adds a new debugfs file.
We can't use debugfs_create_bool for this because the flags are
bitfields, so as this needs a special read callback they have been
collected into a single file that lists all the flags.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds