The rtc isl1208 driver is used by mx6 nitrogen board, so let's enable it by
default.
The fsl sai driver is used by the vf610-twr board, so let's enable it by
default.
simple-audio-card driver is used by the vf610-twr board, so let's enable it by
default.
Generated this patch by doing:
- make imx_v6_v7_defconfig
- make menuconfig and manually select options
- make savedefconfig
- cp defconfig arch/arm/configs/imx_v6_v7_defconfig
,which results in some additional cleanups.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx weim driver is used by some mx27/mx1 boards, so let's enable it by
default.
Generated this patch by doing:
- make imx_v4_v5_defconfig
- make menuconfig and manually select CONFIG_IMX_WEIM
- make savedefconfig
- cp defconfig arch/arm/configs/imx_v4_v5_defconfig
,which results in some additional cleanups.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On i.MX6Q TO > 1.0, i.MX6DL and i.MX6SX, gpt per clock
can be from OSC instead of ipg_per, as ipg_per's rate
may be scaled when system enter low bus mode, to keep
system timer NOT drift, better to make gpt per clock
at fixed rate, here add support for gpt per clock to
be from OSC which is at fixed rate always.
There are some difference on this implementation of
gpt per clock source, see below for details:
i.MX6Q TO > 1.0: GPT_CR_CLKSRC, b'101 selects fix clock
of OSC / 8 for gpt per clk;
i.MX6DL and i.MX6SX: GPT_CR_CLKSRC, b'101 selects OSC
for gpt per clk, and we must enable GPT_CR_24MEM to
enable OSC clk source for gpt per, GPT_PR_PRESCALER24M
is for pre-scaling of this OSC clk, here set it to 8
to make gpt per clk is 3MHz;
i.MX6SL: ipg_per can be from OSC directly, so no need to
implement this new clk source for gpt per.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add gpt_3m clock for i.mx6qdl, as gpt can source clock
from OSC, some i.MX6 series SOCs has fixed divider of
8 for gpt clock, so here add a fix clk of gpt_3m.
i.MX6Q TO1.0 has no gpt_3m option, so force it to be
from ipg_per.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
There is a copy&paste error on register offset of pll7_usb_host gate
clock introduced by i.MX6 PLL bypass support patches. The error breaks
the ENET function, because it overwrites the pll6_enet gate bit.
Correct the offset for all i.MX6 clock drivers.
Thanks to Fugang Duan <B38611@freescale.com> for spotting the error.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Each SSI has "ssi", "ssi_ipg" clocks, and they share same gate bits.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since ENABLE and BYPASS bits of PLLs are now implemented as separate
gate and mux clocks by clock drivers, the code handling these two bits
can be removed from clk-pllv3 driver.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This is the same change for imx6sx clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sx.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This is the same change for imx6sl clock driver as "ARM: imx6q: add BYPASS
support for PLL clocks" for imx6q. The difference is that only anaclk1
is available on imx6sl.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx6q clock driver currently hard-codes all PLL clocks to source
from OSC24M without BYPASS support. The patch adds the missing lvds_in
clock which is mutually exclusive with lvds_gate, and implements BYPASS
and BYPASS_CLK_SRC selection for PLL clocks as per Figure 10-3. Primary
Clock Generation in IMX6DQRM, i.e. both BYPASS_CLK_SRC and BYPASS bits
are implemented as mux clocks, and ENABLE bit of PLL clocks is
implemented as a gate clock after BYPASS mux.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
There are a couple of gate clocks are mutually exclusive on i.MX6, i.e.
LVDSCLK1_IBEN and LVDSCLK1_OBEN. They cannot be enabled simultaneously.
This patches adds an exclusive gate clock type specifically for such
case. The clock driver will need to call imx_clk_gate_exclusive() to
register a gate clock with parameter exclusive_mask indicating the mask
of gate bits which are mutually exclusive to this gate clock.
Right now, it only handles the exclusive gate clocks which are defined
in a single hardware register, which is the case we're running into
today. But it can be extended to handle exclusive gate clocks defined
in different registers later if needed.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Each SSI has "ssi", "ssi_ipg" clocks, and they share same gate bits.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
ASRC has "asrc", "asrc_ipg", "asrc_mem" clocks, and they share
the same gate bits.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The parent clocks of IMX6SL_CLK_PXP_AXI_SEL and IMX6SL_CLK_EPDC_AXI_SEL
clocks are not the same. So split the epdc_pxp_sels into two different
clock selections 'pxp_axi_sels' and 'epdc_axi_sels'.
Signed-off-by: Fancy Fang <chen.fang@freescale.com>
Signed-off-by: Robby Cai <R63905@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
There are three clock for ESAI, esai_extal, esai_ipg, esai_mem. Rename
'esai' to 'esai_extal', 'esai_ahb' to 'esai_mem', and add 'esai_ipg'.
Make the clock for ESAI more clear and align them with imx6sx.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
PLL5 is well suited for being the parent of IMX6SL_CLK_LCDIF_PIX_SEL and
PLL2_PFD for IMX6SL_CLK_LCDIF_AXI_SEL.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Currently csi_lcdif_sels[] is a shared array for the providing the possible
clock parents for csi and lcdif blocks.
This is not correct, as csi and lcdif do not share the same clock parents.
Introduce csi_sels[] for the csi and lcdif_axi_sels[] for the lcdif clocks in
order to describe the parents correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This commit adds PLL7 which is required for USBPHY1. It also adds
the USB PHY and USB Controller clocks and the gates to enable them.
Acked-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add cpufreq support for i.MX6SX, using common
i.MX6Q cpufreq driver.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
At the end of the boot process, the clock framework might disable
required main PLL's. So far, this was no issue since drivers
requested clocks, which are descended of the main PLL's (e.g.
pll1_pfd1, which provides the system clock).
To archive the full 500MHz system clock, DDR clock need to be a
descendant of PLL2 rather than PLL1 (DDRC_CLK_SEL set to 0). The
bootloader sets up the clocks accordingly before making use of
DDR at all. However, in Linux, there is no driver using PLL2,
which lead to PLL2 being disabled by the clock framework.
With this patch, we make sure that the main system clock and the
DDR clock are initially enabled and are kept enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds basic devicetree support for i.MX1 based SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add more revision support for the new i.MX6DQ tape-out (TO1.5). This
TO1.5 is the Rev 1.3 as documented in i.MX6DQ data sheet, because TO1.3
and TO1.4 are never revealed.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
All the current support of mach-mxt_td60 board can be converted to devicetree.
Remove the board file.
Cc: Alan Carvalho de Assis <acassis@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
mx1ads.c can be replaced with devicetree equivalent: imx1-ads.dts,
so remove the board file.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This was added by:
Commit 8128c4f36 ("ARM: dts: vf610-twr: Add simple-card support.")
This useless property may cause some confusions for users.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
With commit c716483c3d ("ARM: 8122/1: smp_scu: enable SCU standby
support"), the STANDBY bit of SCU is handled by core function
scu_enable(). So imx_scu_standby_enable() can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
pcm970-baseboard.c and mach-pcm038.c can be replaced with their
devicetree equivalents: imx27-phytec-phycore-rdk.dts and
imx27-phytec-phycore-som.dtsi respectively, so remove the board files.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
eukrea_mbimx27-baseboard.c and mach-cpuimx27.c can be replaced with their
devicetree equivalents: imx27-eukrea-mbimxsd27-baseboard.dts and
imx27-eukrea-cpuimx27.dtsi respectively, so remove the board files.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The iomux function declarations are in headers only accessible in this
directory. Thus those can't be used in any module. None of the
objects in this directory is tristate. Neither can the header be included
in out-of-tree modules.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Pull ARM fixes from Russell King:
"Various assorted fixes:
- a couple of patches from Mark Rutland to resolve an errata with
Cortex-A15 CPUs.
- fix cpuidle for the CPU part ID changes in the last merge window
- add support for a relocation which ARM binutils is generating in
some circumstances"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
ARM: 8128/1: abort: don't clear the exclusive monitors
ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations
Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support for Broadcom's
STB SoC -- it was accidentally merged before some issues had been addressed, so they
will make a new attempt for 3.18. I didn't see a need for a full revert of the whole
platform due to this, we're keeping the rest enabled.
The rest is mostly:
* A handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
* Some MTD/NAND fixes for OMAP
* Minor DT fixes for shmobile
* Warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's small
and isolated so it made sense to pick up now even if it's not a bugfix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/AD8
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the weekly batch of fixes from arm-soc.
The delta is a largeish negative delta, due to revert of SMP support
for Broadcom's STB SoC -- it was accidentally merged before some
issues had been addressed, so they will make a new attempt for 3.18.
I didn't see a need for a full revert of the whole platform due to
this, we're keeping the rest enabled.
The rest is mostly:
- a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
- some MTD/NAND fixes for OMAP
- minor DT fixes for shmobile
- warning fix for UP builds on vexpress/spc
There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
so it can boot. Drivers and the rest had landed for 3.17, and it's
small and isolated so it made sense to pick up now even if it's not a
bugfix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
vexpress/spc: fix a build warning on array bounds
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
MAINTAINERS: catch special Rockchip code locations
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: brcmstb: revert SMP support
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
...
With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:
arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
struct ve_spc_opp *opps = info->opps[cluster];
^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
are OMAP2+ derivative SoCs. This should be low-risk to existing OMAP
platforms.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5ZS8
-----END PGP SIGNATURE-----
Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:
Add basic subarchitecture support for the DRA72x and DRA74x. These
are OMAP2+ derivative SoCs. This should be low-risk to existing OMAP
platforms.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: Olof Johansson <olof@lixom.net>
New system call depends on crypto. As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.
But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto. Remove that dependency.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series updates the device tree vendor prefix for
Dialog Semiconductor.
Various methods are currently used throughout the kernel: 'diasemi',
'dialog' and 'dlg'. Others have also been suggested.
This patch set aims to consolidate the usage of the vendor prefix to
use a common standard. The prefix 'dlg' is used.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
(and a sneaky document addition that slipped from the previous pull-request)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DaB2
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd fixes from Lee Jones:
"Couple of simple fixes due for the 3.17 rcs
(and a sneaky document addition that slipped from the previous
pull-request)"
* tag 'mfd-fixes-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: twl4030-power: Fix PM idle pin configuration to not conflict with regulators
mfd: tc3589x: Add device tree bindings
mfd: ab8500-core: Use 'ifdef' for config options
mfd: htc-i2cpld: Fix %d confusingly prefixed with 0x in format string
mfd: omap-usb-host: Fix %d confusingly prefixed with 0x in format string
Commit 43fef47f94 (mfd: twl4030-power: Add a configuration to turn
off oscillator during off-idle) added support for configuring the PMIC
to cut off resources during deeper idle states to save power.
This however caused regression for n900 display power that needed the
PMIC configuration to be disabled with commit d937678ab6 (ARM: dts:
Revert enabling of twl configuration for n900).
Turns out the root cause of the problem is that we must use
TWL4030_RESCONFIG_UNDEF instead of DEV_GRP_NULL to avoid disabling
regulators that may have been enabled before the init function
for twl4030-power.c runs. With TWL4030_RESCONFIG_UNDEF we let the
regulator framework control the regulators like it should. Here we
need to only configure the sys_clken and sys_off_mode triggers for
the regulators that cannot be done by the regulator framework as
it's not running at that point.
This allows us to enable the PMIC configuration for n900.
Fixes: 43fef47f94 (mfd: twl4030-power: Add a configuration to turn off oscillator during off-idle)
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To deal with IPs which are specific to dra74x and dra72x, maintain seperate
ocp interface lists, while keeping the common list for all common IPs.
Move USB OTG SS4 to dra74x only list since its unavailable in
dra72x and is giving an abort during boot. The dra72x only list
is empty for now and a placeholder for future hwmod additions which
are specific to dra72x.
Fixes: d904b38df0 ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss")
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
[paul@pwsan.com: fixed comment style to conform with CodingStyle]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 4bfb358b1d
("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
which was included in v3.15.
This fix does not have any run-time affect at this time.
* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 9f13ee6f83
("ARM: shmobile: r8a7790: add div4 clocks")
which was included in v3.11.
This fix does not have any run-time affect at this time.
* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
This resolves a problem introduced by a0f7e7496d
("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
which was included in v3.17-rc1.
This fix does not have any run-time affect at this time as the clock in
question is used by a SCIF device that is not enabled by default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jurT
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Clock Fixes For v3.17" from Simon Horman:
* ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 4bfb358b1d
("ARM: shmobile: Add r8a7791 legacy SDHI clocks")
which was included in v3.15.
This fix does not have any run-time affect at this time.
* ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
This resolves a problem introduced by 9f13ee6f83
("ARM: shmobile: r8a7790: add div4 clocks")
which was included in v3.11.
This fix does not have any run-time affect at this time.
* ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
This resolves a problem introduced by a0f7e7496d
("ARM: shmobile: sh73a0: add CMT1 clock support for DT")
which was included in v3.17-rc1.
This fix does not have any run-time affect at this time as the clock in
question is used by a SCIF device that is not enabled by default.
* tag 'renesas-clock-fixes-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
ARM: shmobile: r8a7790: add missing 0x0100 for SDCKCR
ARM: shmobile: sh73a0: Remove spurious 0x from SCIFB clock name
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
configuration missing
- A couple small SolidRun board fixes/correction from Rabeeh
and Russell
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT/XBJAAoJEFBXWFqHsHzOuqgH/3XqY4n0kL7lZQGRl8sBA/1m
bLtlKYaGjtn5ITXYONuWyxk9MrkCUaVUEEkcM3Gty6kHbCZ9F8nqSa5NiYs4MyGR
FiBX1GANmz96t61i90jlNNxHdPfnmgj3ZXEDTEj9g2brwGceUgQZv4/D59qSy41H
VlyIIOREQbrIoFlln1cEaKf2UXOpmSpB835QHROwy9K4aK0kZKAR4v5eqM2aQaIl
9VpvR5Xfsmr5vH/srlkY+Vc2ODVF1nQZsa3ikleAh2rzFQ4thwSKqpSxF7HL6EAo
zafJuI67ctyzIFk1PlsUuqCM2NimzACnpgrNG6Vn2KDq/JavNIsuyna0KgzzXqE=
=jOFz
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.17, 2nd take" from Shawn Guo:
i.MX fixes for 3.17, 2nd take:
- Fixes suspend/resume issue on imx53-qsrb due to PMIC IRQ pin
configuration missing
- A couple small SolidRun board fixes/correction from Rabeeh
and Russell
* tag 'imx-fixes-3.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: microsom-ar8035: MDIO pad must be set open drain
ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
ARM: dts: imx53-qsrb: Fix suspend/resume
Signed-off-by: Olof Johansson <olof@lixom.net>
by default as that's what many boards expect. Also fixes for omap5
clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
other minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i+aY
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.17-rc2" from Tony Lindgren:
Fixes for omaps, mostly to revert NAND back to using software ECC
by default as that's what many boards expect. Also fixes for omap5
clocks, PM wake-up events, GPIO interrupt cells for dra7, and few
other minor fixes.
* tag 'omap-for-v3.17/fixes-against-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
ARM: dts: Enable UART wake-up events for beagleboard
ARM: dts: Remove twl6030 clk32g "regulator"
ARM: OMAP2+: omap_device: remove warning that clk alias already exists
ARM: OMAP: fix %d confusingly prefixed with 0x in format string
ARM: dts: DRA7: fix interrupt-cells for GPIO
mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
mtd: nand: omap: Revert to using software ECC by default
Commit af040ffc9b ("ARM: make it easier to check the CPU part number
correctly") changed ARM_CPU_PART_X masks, and the way they are returned and
checked against. Usage of read_cpuid_part_number() is now deprecated, and
calling places updated accordingly. This actually broke cpuidle-big_little
initialization, as bl_idle_driver_init() performs a check using an hardcoded
mask on cpu_id.
Create an interface to perform the check (that is now even easier to read).
Define also a proper mask (ARM_CPU_PART_MASK) that makes this kind of checks
cleaner and helps preventing bugs in the future. Update usage accordingly.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On revisions of Cortex-A15 prior to r3p3, a CLREX instruction at PL1 may
falsely trigger a watchpoint exception, leading to potential data aborts
during exception return and/or livelock.
This patch resolves the issue in the following ways:
- Replacing our uses of CLREX with a dummy STREX sequence instead (as
we did for v6 CPUs).
- Removing the clrex code from v7_exit_coherency_flush and derivatives,
since this only exists as a minor performance improvement when
non-cached exclusives are in use (Linux doesn't use these).
Benchmarking on a variety of ARM cores revealed no measurable
performance difference with this change applied, so the change is
performed unconditionally and no new Kconfig entry is added.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors
upon entry to the kernel, but this is redundant:
- We clear the monitors on every exception return since commit
200b812d00 ("Clear the exclusive monitor when returning from an
exception"), so this is not necessary to ensure the monitors are
cleared before returning from a fault handler.
- Any dummy STREX will target a temporary scratch area in memory, and
may succeed or fail without corrupting useful data. Its status value
will not be used.
- Any other STREX in the kernel must be preceded by an LDREX, which
will initialise the monitors consistently and will not depend on the
earlier state of the monitors.
Therefore we have no reason to care about the initial state of the
exclusive monitors when a data abort is taken, and clearing the monitors
prior to exception return (as we already do) is sufficient.
This patch removes the redundant clearing of the exclusive monitors from
the early abort handlers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel module build with GCOV profiling fails to load with the
following error:
$ insmod test_module.ko
test_module: unknown relocation: 38
insmod: can't insert 'test_module.ko': invalid module format
This happens because constructor pointers in the .init_array section
have not supported R_ARM_TARGET1 relocation type.
Documentation (ELF for the ARM Architecture) says:
"The relocation must be processed either in the same way as R_ARM_REL32 or
as R_ARM_ABS32: a virtual platform must specify which method is used."
Since kernel expects to see absolute addresses in .init_array R_ARM_TARGET1
relocation type should be treated the same way as R_ARM_ABS32.
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is important for the MicroSOM implementation due to the
following details -
1. VIH of the Atheros phy is 1.7V.
2. NVCC_ENET which is the power domain of the MDIO pad is driven by the
PHY's LDO (i.e. either 1.8v or 2.5v).
3. The MicroSOM implements an onbouard 1.6kohm pull up to 3.3v (R3000).
In the case the PHY's LDO was 1.8v then there would be only a 100mV
margin for the signal to be acknowledged as high (1.8v-1.7v).
Due to that setting the pad as an open drain will let the 1.6kohm pull
that signal high to 3.3 that assures enough margins to the PHY to be
acked as '1' logic.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Shawn Guo