LDO indices start from 1. Update the example accordingly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for DMA controller of BCM2835 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Even though we might not have rigor rule for the simple card property names,
according to the existing ones, they are all in a same pattern:
[simple-audio-card,]XXX;
Rename simple-audio-routing to simple-audio-card,routing, and make the simple
card's properties has one unified name.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Palmas device contains only a USB VBUS-ID detector, so added a
compatible type *ti,palmas-usb-vid*. Didn't remove the existing compatible
types for backward compatibility.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0B0x
-----END PGP SIGNATURE-----
Merge tag 'samsung-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes
Samsung Clock fixes for 3.13-rc7
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
Add support for the MXS DCP block. The driver currently supports
SHA-1/SHA-256 hashing and AES-128 CBC/ECB modes. The non-standard
CRC32 is not yet supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Document the clock properties required by the at91 i2c bus driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device tree support for twl4030 keypad driver.
Tested on Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cCZc
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
From Linus Walleij:
Some Integrator patches that matured for v3.14:
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
* tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
ARM: integrator: Default enable ARM_PATCH_PHYS_VIRT, AUTO_ZRELADDR
Signed-off-by: Olof Johansson <olof@lixom.net>
This mostly adds the reset controller initialisation for the A31 and the SMP
operations for this SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=zEQv
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.14' of https://github.com/mripard/linux into next/drivers
From Maxime Ripard:
Allwinner core changes for 3.14
This mostly adds the reset controller initialisation for the A31 and the SMP
operations for this SoC.
* tag 'sunxi-core-for-3.14' of https://github.com/mripard/linux:
ARM: sun6i: Add SMP support for the Allwinner A31
dt-bindings: fix example of allwinner interrupt controller
ARM: sunxi: Register the A31 reset IP in init_time
ARM: sunxi: Select ARCH_HAS_RESET_CONTROLLER
Signed-off-by: Olof Johansson <olof@lixom.net>
The Versatile FPGA interrupt controller supports cascading interrupts,
i.e. that its output is connected to the input of another interrupt
controller. This makes it possible to pass a parent interrupt from
the device tree and print it in the boot log if applicable.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Keystone arch has compatible nand device, so reuse it.
In case with Keystone it depends on TI_AEMIF because AEMIF
driver is responsible to set timings.
See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The properties davinci-ecc-mode, davinci-nand-use-bbt, davinci-nand-buswidth
are MTD generic. Correct names for them are: nand-ecc-mode, nand-on-flash-bbt,
nand-bus-width accordingly. So rename them in dts and documentation.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Extend bindings for davinci_nand driver to be more clear.
This is clarification only, without semantic changes.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Move bindings under mtd. Do this in order to make davinci-nand
driver usable by keystone architecture.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the driver supports the new compatible string, the binding
documentation must be updated to reflect it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In default way, we use the ecc_strength/ecc_step size calculated by ourselves
and use all the OOB area.
This patch adds a new property : "fsl,use-minimum-ecc"
If we enable it, we will firstly try to use the datasheet's minimum required
ECC provided by the MTD layer (the ecc_strength_ds/ecc_step_ds fields
in the nand_chip{}). So we may have free space in the OOB area by using the
minimum ECC, and we may support JFFS2 with some SLC NANDs, such as Micron's
SLC NAND.
If we fail to use the minimum ECC, we will use the legacy method to calculate
the ecc_strength and ecc_step size.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds polling mode support for i2c-s3c2410 driver.The
SATA PHY controller's CMU and TRSV block's are of I2C register
map in exynos5250.These blocks can be configured using i2c.
But i2c controller instance on which these block's sits lacks an
interrupt line.Also the current i2c-s3c2410 driver is only interrupt
driven, thus a polling mode support is required in the driver for
supporting this controller. This patch adds this support to the driver.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a reset GPIO support is specified, request the GPIO and get the chip
out of reset at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Thermal sensor needs pll3_usb_otg when measuring temperature,
otherwise the temperature read will be incorrect, so need to
enable this clk before sensor working, for alarm function,
as hardware will take measurement periodically, so we should
keep this clk always on once alarm function is enabled.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSwiPBAAoJEFBXWFqHsHzO3/AIALlP6m/7taIQW5wO4o4aqdwk
GsN7IdsfWH/biG9VyxgpIoJKUqaOJckGA0eyLSeEG7p78xlf0n7cVPUNwzz9z1Vc
zxLSaVNznVOa4fTIsbMK9U+gUP931hjXskxD3tH98MUFqlM0JLQYoofr/lXG7Esf
N2p8B9aUND3WSxDa+d+CsW0B3FBj1piOQDMDgrdc3p7kjcAJs31KaKfUa06o7gzM
a81OaD9Vk0ONf44wh1LGlg0hDRsatQOa4tUTimeV14CnESKqsKxT4qAJ6pZLdfOt
KyRqSk4f4mkpimv4bGdhXTIsIko1CD9wg7G9fsSaolh3OEP0yyNf1savR1fmwCI=
=Hhbl
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
i.MX SoC changes for 3.14:
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
* tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6: (37 commits)
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
ARM: imx: update imx_v6_v7_defconfig
ARM: imx6sl: Add missing spba clock to clock tree
ARM: imx6sl: Add missing pll4_audio_div to the clock tree
ARM: imx6: Derive spdif clock from pll3_pfd3_454m
ARM: imx: use __initconst for const init definition
ARM i.MX5: fix obvious typo in ldb_di0_gate clk definition
ARM i.MX5: set CAN peripheral clock to 24 MHz parent
ARM: imx: pllv1: Fix PLL calculation for i.MX27
ARM i.MX5: fix "shift" value for lp_apm_sel on i.MX50 and i.MX53
ARM: imx: imx53: Add SATA PHY clock
ARM: imx_v6_v7_defconfig: Enable STMPE touchscreen
ARM: imx: rename IMX6SL_CLK_CLK_END to IMX6SL_CLK_END
ARM: imx: select PINCTRL at sub-architecure level
...
Signed-off-by: Olof Johansson <olof@lixom.net>
---------------------------
This pull request contains updates
to DaVinci GPIO driver and the
resultant platform code changes. The
updates include DT-conversion and
changes to make the driver cross-platform
ready.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=DxLt
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=IZCI
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Third Round of Renesas SH SCI Updates for v3.14
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
* tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
Signed-off-by: Olof Johansson <olof@lixom.net>
Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Capella Microsystem CM32181 Ambient Light Sensor IIO driver.
This driver will convert raw data to lux value under open-air
condition. Change the calibscale based on the cover material.
Signed-off-by: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Document the device tree binding for Broadcom Kona architecture
clock control units and clocks. Kona device nodes are represented
with compatible strings having "bcm11351" in their name.
Kona clocks are managed by "clock control units" (CCUs). Each CCU
has a device tree node, and within that node are defined the names
of the clocks provided by the CCU.
The BCM281xx family of SoCs use Kona CCUs and clocks.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
Use clock defines in order to make devicetrees more
human readable.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Adds gate clock for MDMA0 on Exynos5250 SoC. This is needed to ensure
that the clock is enabled when MDMA0 is used on systems on which
firmware gates the clockby default.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This adds support for the Marvell Tauros3 cache controller which
is compatible with pl310 cache controller but broadcasts L1 cache
operations to L2 cache. While updating the binding documentation,
clean up the list of possible compatibles. Also reorder driver
compatibles to allow non-ARM derivated to be compatible to ARM
cache controller compatibles.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the external clock outputs on the
Allwinner A20 SoC. The clock outputs are similar to "module 0"
type clocks, with different offsets and widths for clock factors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
This commit implements support for the "module 0" type of clocks, as
used by MMC, IR, NAND, SATA and other components.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit implements PLL5 and PLL6 support on the sunxi clock driver.
These PLLs use a similar factor clock, but differ on their outputs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit adds gating support to PLL1 on the clock driver. This makes
the PLL1 implementation fully compatible with PLL4 as well.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Two drivers are merged through for 3.14:
- The A10/A20 RTC driver
- The A31 reset controller IP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=7spL
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drivers-for-3.14' of https://github.com/mripard/linux into next/drivers
From Maxime Ripard:
Allwinner SoC additions for 3.14
Two drivers are merged through for 3.14:
- The A10/A20 RTC driver
- The A31 reset controller IP
* tag 'sunxi-drivers-for-3.14' of https://github.com/mripard/linux:
ARM: sun4i/sun7i: RTC driver
ARM: sun4i/sun7i: DT documentation for RTC driver
reset: Add Allwinner SoCs Reset Controller Driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the Trusted Foundations secure-mode firmware, as found
on NVIDIA SHIELD. This allows Linux to run in non-secure mode on this
board; all previous Tegra support has assumed the kernel is running in
secure mode.
This branch is based on v3.13-rc1, and shouldn't cause any merge
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSr3NgAAoJEMzrak5tbycxRXkP/imK6IQn5cAtXY7nfKnn4Rke
RjvERwURDpi6QDrXaRe6NUVg3PgZ0Z7kXLqSuj/cAPinMyhQDR5DxlJVjYiduJ50
CmMhV+RWkA/cmaU2oPjpD3YEm68txYXTyf3iWfX1ScFSuNNN0yGel3eY2rFjX/aT
RgAWm8HbQTR7NDazAAt9gOqeJUtfs3msXwMxtZvD6OhRougyaPlqfuafjVpfM9vK
JLDAbJuMEl6/dI2UYVvDBJvL//TOOjnwy6YFwQCZsqhYGHhT3Xc9hQABilUQmJ1d
mbu29cPBrRgGiu3anpjZeh0KxVB3xDPp1a+o4lSH0iJztAPy4WTUZ1Sc3y2qwKaS
qZ5Zu5SXVI1O/ywv1FChL2syuJbgOH+HGBMFslacVniQ/U1o4PmKZCJOB0pnpf8B
dESAQgvDqIZeyt2eXxsAMAOw01xMTotngAaJpAtYFv0plP+PxAhr+dkHHjCwwkde
7+OKeVE5TDDwlhz5PE35/4EWdWM0622aL3sK1IxrR2q66LGpKAoQpFeKaAUr0d6z
OQnQiS+uNSNrCvAEeyEL2bQfv1xsjOFpFy6PV7ShrUrAgPVR3+wj82RvwTciMdbd
tv3Y7LXCugSUOdq/abc3VgAnlgMzlhH5vlj6CMcKSSPbzZ3lbRB37iBmxpJLm9qa
o3Ah/MaWSqtqmIueFrpa
=c5t/
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-trusted-foundations' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
From Stephen Warren:
ARM: tegra: Trusted Foundations firmware support
Add support for the Trusted Foundations secure-mode firmware, as found
on NVIDIA SHIELD. This allows Linux to run in non-secure mode on this
board; all previous Tegra support has assumed the kernel is running in
secure mode.
(The base TF support has been discussed back and forth a lot; for now
the most logical place for it seems to be under arch/arm, so we're adding
it here. We can move it out to a common location in the future if needed).
* tag 'tegra-for-3.14-trusted-foundations' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: support Trusted Foundations by default
ARM: tegra: set CPU reset handler using firmware
ARM: tegra: split setting of CPU reset handler
ARM: tegra: add support for Trusted Foundations
of: add Trusted Foundations bindings documentation
of: add vendor prefix for Trusted Logic Mobility
ARM: add basic support for Trusted Foundations
Signed-off-by: Olof Johansson <olof@lixom.net>
Bringing in the tegra dma/reset rework as a base for new SoC branches.
* tegra/dma-reset-rework: (81 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in external dependencies for the Tegra DMA and reset controller
refactoring from external trees.
Per Stephen Warren, the stability of these branches have been negotiated
with the relevant parties (Vinod/Mark/Mike)
* depends/asoc-dma:
ASoC: dmaengine: fix deferred probe detection
ASoC: dmaengine: support deferred probe for DMA channels
dma: add channel request API that supports deferred probe
ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: restructure dmaengine_pcm_request_chan_of()
ASoC: generic-dmaengine-pcm: Set BATCH flag when residue reporting is not supported
ASoC: Add resource managed snd_dmaengine_pcm_register()
* depends/dma-of:
dma: add dma_get_any_slave_channel(), for use in of_xlate()
* depends/tegra-clk: (42 commits)
clk: tegra: fix __clk_lookup() return value checks
clk: tegra: Do not print errors for clk_round_rate()
clk: tegra: Initialize DSI low-power clocks
clk: tegra: add FUSE clock device
clk: tegra: Properly setup PWM clock on Tegra30
clk: tegra: Initialize secondary gr3d clock on Tegra30
clk: tegra114: Initialize clocks needed for HDMI
clk: tegra124: add suspend/resume function for tegra_cpu_car_ops
clk: tegra124: add wait_for_reset and disable_clock for tegra_cpu_car_ops
clk: tegra124: Add support for Tegra124 clocks
clk: tegra124: Add new peripheral clocks
clk: tegra124: Add common clk IDs to clk-id.h
clk: tegra: add TEGRA_PERIPH_NO_GATE
clk: tegra: add locking to periph clks
clk: tegra: Add periph regs bank X
clk: tegra: Add support for PLLSS
clk: tegra: move tegra20 to common infra
clk: tegra: move tegra30 to common infra
clk: tegra: introduce common gen4 super clock
clk: tegra: move PMC, fixed clocks to common files
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds OF parser support for davinci gpio
driver and also appropriate documentation in gpio-davinci.txt
located at Documentation/devicetree/bindings/gpio/.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: KV Sujith <sujithkv@ti.com>
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
[prabhakar.csengg@gmail.com: simplified the OF code, removed
unnecessary DT property and also simplified
the commit message]
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJStyIbAAoJEFSFNJnE9BaI1goQAL0hKYCYuIl3d1fAy65u2I4h
5mzJs/oJmomq/4BqAopfEQ8CbhZhksAYoR4JndOzZH7n4jVY/fRgyY/bH/Ymj0oI
OpCtfee6IeeBLA0p8CMeEPem/pnwxRhSDzul9jsiwpTrTRKAIC1BPZwrmLpaoUfc
obD8r1ocVZStzfsYBr3DUwkcIpcTQTCVy/Pl8HoKLKKsdYoFhTpNwEHJFOoZdiFi
KKGRkeL9Q8VRWt/otWU0L0VFGZFwI1PWlxrqnbisVcGwSs8FF4wGcQvijfC0mUMg
BdKDM7J4GrourZhj3og566B/8WMtGo6YTJXAe/QvvPp768rQncccDHem4V0Tnu49
OJbjgD4ZGVXt3uBFaYddBIbMEIB8SfA2VYur/MW3gnZ7saSAtDk6TllsvC6CxIkR
+LOOxWylhEGeJFIjyMrFPqRVhrrRNkuDRxPz8ZGTiDc8ovo6DWuTLsJrLSX8EJyZ
O6TN6EEk8TCJaf8V63uTFW0Dlom4IQHyQei6LKhfhzwUQq/ri0esBp5P8lGzI3Uq
wtOSdCDuYyoUEYPYbwjohFmQJ27w1rx9KcS4Y9BGmhTIRXslUg3hr+wA/gKMSDZ0
/AUkLQajcv9otupfGzsp5mIWkthKKsGt/Y50xc5zIodnFtnM3nQGq4AqlP6t8nzP
jucVwVMQLj5KaNH13P6K
=Whfv
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO drivers, features and cleanups for the 3.14 cycle.
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
Document the device tree bindings for the sci serial port devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YqMd
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT 2nd updates for v3.14
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (27 commits)
ARM: dts: Rename Exynos5250 ChromeOS common file to have exynos prefix
ARM: dts: Disable I2C controllers by default on Exynos5250
ARM: dts: Leave Exynos5250 SPI controller disabled by default
ARM: dts: Add CODEC MCLK for SMDK5250
ARM: dts: Add device nodes for TMU blocks for exynos5420
ARM: dts: Fix status property of mmc nodes for snow board
ARM: dts: Fix missing spaces after labels for exynos
ARM: dts: Simplify MCT interrupt map for exynos4 SoCs
ARM: dts: Move MCT node to exynos4x12.dtsi
ARM: dts: Drop interrupt controller properties from MCT nodes for exynos4 SoCs
Documentation: devicetree: Update Exynos MCT bindings description
ARM: dts: add pwm DT nodes to Exynos5250 and Exynos5420
ARM: dts: Add SPI nodes to the exynos5420 device tree file
ARM: dts: Add DMA controller node info on Exynos5420
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
ARM: dts: Fix exynos5250-snow's search key to be L_META
ARM: dts: Add the missing "\" key in non-US keyboards for exynos5250-snow
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add devicetree binding documentation for isp1704-charger.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This adds an UDC driver for GRUSBDC USB Device Controller cores available in the
GRLIB VHDL IP core library. The driver only supports DMA mode.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ams AS3722 device supports the power off by turning off its all rails.
Add dt node properties to enable this functionality on this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Charger-manager can parse charger_desc data from devicetree which is used
to register charger manager.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add a binding that describes the Broadcom Kona USB2 PHY found
on the BCM281xx family of SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2/s3c-hsotg require a single clock to be specified and optionally
a generic phy. On the s3c-hsotg driver old style USB phy support is
present as a fallback so the generic phy properties are optional.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The frequency for the Kona timer can either be specified through the
device tree or determined by checking the rate of the clock specified
in the device tree. Update the documentation to reflect both ways.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
The Kona SDHCI block requires a clock that must be specified in the
device tree. Update the documentation to reflect this requirement.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
This patch adds support for accuracy retrieval on fixed clocks.
It also adds a new dt property called 'clock-accuracy' to define the clock
accuracy.
This can be usefull for oscillator (RC, crystal, ...) definitions which are
always given an accuracy characteristic.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for using emev2 SMU clocks with DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=NhhY
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into clk-next-shmobile2
Renesas ARM based SoC Clock updates for v3.14
Add support for using emev2 SMU clocks with DT
- Add support Octa Cores for exynos5420
: populate CPU node entries to 8 Cores
: extend mct to support 8 local interrupts
- Update dwmmc nodes for exynos5250 and exynos5420
: change status property of dwmmc nodes for exynos5250
: move dwmmc nodes from exynos5 to exynos5250 because
it's different between exynos5250 and exynos5420
: rename mmc nodes from dwmmc for exynos5 SoCs
: add dwmmc nodes for exynos5420
- Add G-Scaler nodes for exynos5420
- Add HS-i2c nodes in exynos5420
: High Speed I2C 7 channels (4 to 10)
- Update sysreg binding and node name in exynos4
- Update min voltage on exynos5250-arndale
- Move fifo-depth property from boards to exynos5250 SoC
: because the fifo-depth property is SoC specific
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6e6p
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT updates for v3.14
- Add support Octa Cores for exynos5420
: populate CPU node entries to 8 Cores
: extend mct to support 8 local interrupts
- Update dwmmc nodes for exynos5250 and exynos5420
: change status property of dwmmc nodes for exynos5250
: move dwmmc nodes from exynos5 to exynos5250 because
it's different between exynos5250 and exynos5420
: rename mmc nodes from dwmmc for exynos5 SoCs
: add dwmmc nodes for exynos5420
- Add G-Scaler nodes for exynos5420
- Add HS-i2c nodes in exynos5420
: High Speed I2C 7 channels (4 to 10)
- Update sysreg binding and node name in exynos4
- Update min voltage on exynos5250-arndale
- Move fifo-depth property from boards to exynos5250 SoC
: because the fifo-depth property is SoC specific
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Update Samsung sysreg binding document
ARM: dts: Fix sysreg node name in exynos4.dtsi
ARM: dts: Add hs-i2c nodes to exynos5420
ARM: dts: Update min voltage for vdd_arm on Arndale
ARM: dts: populate cpu node entries to 8 cpus for exynos5420
clocksource: mct: extend mct to support 8 local interrupts for Exynos5420
ARM: dts: Add device nodes for GScaler blocks for exynos5420
ARM: dts: Add dwmmc DT nodes for exynos5420 SOC
ARM: dts: rename mmc dts node for exynos5 series
ARM: dts: Move fifo-depth property from exynos5250 board dts
ARM: dts: change status property of dwmmc nodes for exynos5250
ARM: dts: Move dwmmc nodes from exynos5.dtsi to exynos5250.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a generic (dtsi) include file for MOXA ART SoCs.
Also add a file for UC-7112-LX.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
- add DT to sha/des/aes existing drivers
- add DMA DT
- all documentation added to crypto/atmel-crypto.txt file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSqfkKAAoJEAf03oE53VmQpHoH/2OnDX5C3hqXXL1r3p6JjRLP
B2xDO2iZcB340HrobInN0FONXVCA2b8yNy2G+U421sNjklivT4o9+66tiwBBQlbS
uoYU95CgeBs5dU1iM8Z5cIRFphEZdKDAJDd0RABUEcVPa+w569nyi5V29rwzH0UZ
hnW0IzUtJqo9344dfBai9cRcVOjrJHfiqB+05PUWb12KFbLaQhqQLL1Z5b0XasB/
9htaMxuXMXhflP7m+JY0+uVlFTOJliY9zUMN/bOqT2VBrl2tt1xLW7nooM57dB3y
+wK1A+mhYHQgEgVm1U6X3+LUluitwyA+yw2Ybf6Yi/T+3tzMjeiknfHfUB5afMY=
=JTE6
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers' of git://github.com/at91linux/linux-at91 into next/drivers
From Nicolas Ferre:
AT91 crypto drivers DT support:
- add DT to sha/des/aes existing drivers
- add DMA DT
- all documentation added to crypto/atmel-crypto.txt file
* tag 'at91-drivers' of git://github.com/at91linux/linux-at91:
crypto: atmel-sha - add sha information to the log
crypto: atmel-sha - add support for Device Tree
crypto: atmel-tdes - add support for Device Tree
crypto: atmel-aes - add support for Device Tree
Signed-off-by: Olof Johansson <olof@lixom.net>
Intersil ISL12057 is an I2C RTC chip also supporting two alarms. This
patch only adds support for basic RTC functionalities (i.e. getting
and setting time). Tests have been performed on NETGEAR ReadyNAS 102
w/ startup/shutdown scripts, hwclock, ntpdate and openntpd.
Reviewed-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
tps65910 has a backup battery charger with a configurable voltage. This
patch adds a regulator for the backup battery.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Device Tree support to the Microchip MCP251X driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch updates description of device tree bindings for Exynos MCT
(multicore timers). Namely:
- added note about simplified specification of local timer interrupts,
when using single per-processor interrupt for all local timers,
- changed first example that was incorrectly suggesting that global
timer interrupts are optional,
- simplified example interrupt map,
- added example showing simplified local timer interrupt specification.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add DT documentation for SUNXI RTC driver
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
From Uwe Kleine-König:
* efm32/soc: (1003 commits)
ARM: device trees for Energy Micro's EFM32 Cortex-M3 SoCs
ARM: new platform for Energy Micro's EFM32 Cortex-M3 SoCs
+Linux 3.13-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.
Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In some use cases Zynq's FPGA clocks are used as static clock
generators for IP in the FPGA part of the SOC for which no Linux driver
exists and would control those clocks. To avoid automatic
gating of these clocks in such cases a new property - fclk-enable - is
added to the clock controller's DT description to accomodate such use
cases. It's value is a bitmask, where a set bit results in enabling
the corresponding FCLK through the clkc.
FPGA clocks are handled following the rules below:
If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
Linux. Drivers can enable and control it through the CCF as usual.
If an FCLK is enabled by bootloaders AND the corresponding bit in the
'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
resulting in an off by one reference count for that clock. Ensuring it
will always be running.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some boards do not have a PCIe reset GPIO. To avoid probe failure on these
boards, make the reset GPIO optional as well.
[bhelgaas: whitespace fixes]
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
This adds omap control module support for USBSS in AM437x SoC.
Update DT binding information to reflect these changes.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These update binding information for ti qspi controller.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Document the clock properties required by the atmel-ssc driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the clock properties required by the atmel_tclib driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the Document for Freescale SAI driver under
Documentation/devicetree/bindings/sound/.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch enables the JPEG codec on S5PV210 and Exynos4210 SoCs. There are
some differences in newer versions of the JPEG codec IP on SoCs like Exynos4x12
and Exynos5 series and support for them will be added in subsequent patches.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add board support with device tree for Hisilicon Hi3620 SoC platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
[khilman: fix checkpatch errors]
[khilman: fold in patch which selects GPIO in Kconfig]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Document the clock properties required by the at91 usart driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the devicetree documentation for the Cirrus Logic
CLPS711X UART.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce device tree bindings for the MIPI pad calibration controller
found on Tegra SoCs. The controller can be used to perform calibration
of pads used for DSI and CSI peripherals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller primary clock was recently renamed to "dc", so
update the example to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the DRM panel framework to attach a panel to an output. If the panel
attached to a connector supports supports the backlight brightness
accessors, a property will be available to allow the brightness to be
modified from userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This binding specifies a set of common properties for display panels. It
can be used as a basis by bindings for specific panels.
Bindings for three specific panels are provided to show how the simple
panel binding can be used.
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Document the device tree bindings for the MIPI DSI bus. The MIPI Display
Serial Interface specifies a serial bus and a protocol for communication
between a host and up to four peripherals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' into drm/for-next
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
The Atmel PWM controller uses the standard device tree bindings for PWM
controllers.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Synchronize with mainline to bring in the new keycode definitions and
new hwmon API.
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the more specific form 8974 for the compatible to reduce the
risk of future mishaps.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new DMA_TYPE for SSI dual FIFO script, included
in SDMA firmware version 2. This script would allow SSI use dual
fifo mode to transimit/receive data without occasional hardware
underrun/overrun.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Added a binding example for reference and updated the
node name. While at it also removed the name description
as it is not necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the mmc device tree node entries for exynos5420 SOC.
Exynos5420 has a different version of DWMMC controller,so a new
compatible string is used to distinguish it from the prior SOC's.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a driver for SILabs 570, 571, 598, 599 programmable oscillators.
The devices generate low-jitter clock signals and are reprogrammable via
an I2C interface.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Device tree clock binding document for EMMA Mobile EV2 SMU,
And Common clock framework based implementation of it.
Following nodes are defined to describe clock tree.
- renesas,emev2-smu
- renesas,emev2-smu-clkdiv
- renesas,emev2-smu-gclk
These bindings are designed manually based on
19UH0037EJ1000_SMU : System Management Unit User's Manual
So far, reparent is not implemented, and is fixed to index #0.
Clock tree description is not included, and should be provided
by device-tree.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Register the firmware operations for Trusted Foundations if the device
tree indicates it is active on the device.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the Device Tree bindings documentation for the Trusted Foundation
secure monitor.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds very basic device tree files for the Marvell Armada 1500 SoC
(Berlin BG2) and the Sony NSZ-GS7 GoogleTV board. Currently, SoC only has
nodes for cpus, some clocks, l2 cache controller, local timer, apb timers,
uart, and interrupt controllers. The Sony NSZ-GS7 is a GoogleTV consumer
device comprising the Armada 1500 SoC above.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
This adds an irqchip driver and corresponding devicetree binding for the
secondary interrupt controllers based on Synopsys DesignWare IP dw_apb_ictl.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
MSTP clocks are gate clocks controlled through a register that handles
up to 32 clocks. The register is often sparsely populated.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
DIV6 clocks are divider gate clocks controlled through a single
register. The divider is expressed on 6 bits, hence the name, and can
take values from 1/1 to 1/64.
Those clocks are found on Renesas ARM SoCs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:
- Fixed rate clocks with multiplier and divisor set according to boot
mode configuration
- Custom divider clocks with SoC-specific divider values
This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Added device tree support for TI's Keystone USB driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Added device tree support for TI's Keystone USB PHY driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This device tree binding document describes the Tegra124 pincontrol
DT bindings. This document lists all valid properties, names, mux
options of Tegra124 pins.
Changes from V1:
- Referred the dt-binding header file on describing the nodes.
Changes from V2:
- Rewording reg properties.
- drop drv_type as it is not applicable.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On non-DT platforms IRQ controllers associated with the GPIOs have a
fixed IRQ base value known at compile time. The sh-pfc driver translates
GPIO number to IRQ numbers using a hardcoded table. This mechanism
breaks on DT platforms, as the IRQ base values are dynamic in that case.
Fix this by specifying IRQs associated with GPIOs in IRQ resources,
populated automatically from the device tree. When IRQ resources are
specified the driver requires one IRQ resource per GPIO able to generate
an interrupt, and uses the translation table to compute the IRQ resource
offset instead of the IRQ number.
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra124 adds a number of extra modules into the configlink bus, which
must be taken out of reset before the bus is used. Update the AHUB
driver to know about these extra modules (the AHUB HW module hosts the
configlink bus).
Based-on-work-by: Arun Shamanna Lakshmi <aruns@nvidia.com>
Based-on-work-by: Songhee Baek <sbaek@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@linaro.org>
---
This patch depends on "ASoC: tegra: use reset framework" to compile,
which is ack'd and slated to go through a (large) topic branch in the
Tegra tree. So, we can either:
a) Merge that Tegra topic branch into the ASoC tree, then apply this.
Note that I haven't created the topic branch yet, since I'm still
waiting for DMA dependencies to be applied.
b) Apply this change to the Tegra tree too. This change isn't directly
related to the changes in the Tegra tree; it just makes use of the new
reset controller feature that's introduced there.
Add support for Device Tree and use of the DMA DT API to
get the channels if needed.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the channels if needed.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Device Tree and use of the DMA DT API to
get the needed channels.
Documentation is added for these DT nodes.
Initial code by: Nicolas Royer and Eukrea.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
The documented value of #interrupt-cells is 1.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Update all the Tegra DT bindings to require the standard dmas/dma-names
properties rather than non-standard nvidia,dma-request-selector property.
This is a DT-ABI-incompatible change. It is the second of two changes
required for me to consider the Tegra DT bindings as stable, the other
being the previous conversion to the common reset bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Update all the Tegra DT bindings to require resets/reset-names properties
where the HW module has reset inputs. Remove any entries from clocks or
clock-names that were only required to identify reset inputs, rather than
referring to real clocks.
This is a DT-ABI-incompatible change. It is the first of two changes
required for me to consider the Tegra DT bindings as stable, the other
being conversion to the common DMA DT bindings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Commit 89ce376c6b (drivers/net: Use of_match_ptr() macro in smc91x.c)
added minimal device tree support to smc91x, but it's not working on
many platforms because of the lack of some key configuration bits.
Fix the issue by parsing the necessary configuration like the
smc911x driver is doing. As most smc91x users seem to use 16-bit
access, let's default to that if no reg-io-width is specified.
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Delete some static core module mappings.
- Move EBI location to the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=efPU
-----END PGP SIGNATURE-----
Merge tag 'integrator-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
From Linus Walleij:
Two integrator device tree patches for v3.14:
- Delete some static core module mappings.
- Move EBI location to the device tree.
* tag 'integrator-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: move EBI to the device tree
ARM: integrator: delete static core module mappings
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Most of the Allwinner SoCs (at this time, all but the A10) also have a
High Speed timers that are not using the 24MHz oscillator as a source
but rather the AHB clock running much faster.
The IP is slightly different between the A10s/A13 and the one used in
the A20/A31, since the latter have 4 timers available, while the former
have only 2 of them.
[dlezcano] : Fixed conflict with b788beda "Order Kconfig options
alphabetically"
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSpd+hAAoJEAf03oE53VmQB7cH+wVFP2N7+kGTB9WTBFOmTt/6
tAEyO/yUTGPZiDV1Vsb5F+MPi+de3pt0t9Br11bXSDolzwHPDMhcGXCDxpJlyYrN
sIGXO2YtUmIo+QMqShRXOgoozkGqXxpOqVt4vZRaEOQguVja5NJz7xbXUmoma8a/
eKgt94Bqyfmnv1wIsjgz3AR1mXYMKIZbDxJ1IZvVLwNnp6n6H8Lrh5qrOloICJ0Z
sm0gD85lq/An9FGiYDQkxAlIkYNFHlB0fmQdLw+uKLTRftT7EuGK4RqawrzQW84E
32pZ6fzLTCQ1FQfkpamEOrWaoF4DDvTuBn3YXCtk7bA/8gNCmX7y42PcCR6UHpY=
=7H2V
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
First DT pull-request for 3.14
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/at91rm9200ek.dts: rearrange nodes in address ascending order
ARM: at91: dt: at91rm9200ek: add emac and nor flash support
ARM: at91: add uart aliases to sama5d3 dtsi
ARM: at91: add i2c2 pinctrl speficifation to sama5d3 DT
ARM: at91: Animeo IP: fix mtd partition table
ARM: at91: at91sam9g45: add i2c pinctrl
ARM: at91: at91sam9g45: set default mmc pinctrl-names
ARM: at91: sama5d3: enable qt1070 as a wakeup source
ARM: at91: add support for Cosino board series by HCE Engineering
ARM: at91/dt/sama5d3: add DMA information to SHA/AES/TDES nodes
ARM: at91/dt/trivial: before sama5d3, Atmel MPU were using at91 prefix
ARM: at91/dt/trivial: use macro for AES irq type
ARM: at91: sam9263ek: add dt lcd support
ARM: at91: at9sam9m10g45ek: add dt lcd support
ARM: at91: sam9263: add fb dt support
ARM: at91: sam9g45: add fb dt support
ARM: at91/dt: binding: add missing compatibility string in SDRAM/DDR documentation
ARM: at91/dt: binding: add precision to AIC documentation
ARM: at91/dt: add atmel,pullup-gpio to at91rm9200ek usb1 definition
ARM: at91/dt: add ethernet phy to at91rm9200ek board
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
DDR3A/B, ARM and PA PLL controllers have clkod register bits for
configuring postdiv values. So use it instead of using fixed
post dividers for these pll controllers. Assume that if fixed-postdiv
attribute is not present, use clkod register value for pistdiv.
Also update the Documentation of bindings to reflect the same.
Cc: Mike Turquette <mturquette@linaro.org
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Optional DT property to specify the desired parent clock for the McASP fck
clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The IP in DRA7xx is similar to the IP found in TI81xxAM3xxx/AM4xxx type of
SoCs but it is is integrated with sDMA instead of eDMA. The suitable pcm
driver for DRA7xx is the omap-pcm driver which is using dmaengine.
In the driver we can configure both dma related structures used for eDMA and
sDMA. The only thing we need to make sure that we set the correct dma_data
at startup with snd_soc_dai_set_dma_data()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
AM43xx have the same McASP IP as AM33xx and both platform uses eDMA. Modify
the Kconfig so it will be possible to add audio support for AM43xx based
boards later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7431798490 (of_spi: add generic binding support to specify cs gpio)
introduced generic binding for gpio chip-select. The cs_gpio struct field,
however, is an internal implementation detail of the Linux SPI subsystem, and
should not be mentioned in the device tree binding documentation. Mention the
previously defined cs-gpios master node property instead.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the devicetree documentation for the ADI AXI-SPDIF audio
controller. The controller has:
* One set of memory mapped register
* Two clocks, one for the memory mapped register interface, one used as the
audio reference clock
* A DMA interface for the transmit data
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the devicetree documentation for the ADI AXI-SPDIF audio
controller. The controller has:
* One set of memory mapped register
* Two clocks, one for the memory mapped register interface, one used as the
audio reference clock
* One DMA interface each for the transmit and receive data
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Signed-off-by: Mark Brown <broonie@linaro.org>
The "atmel,at91rm9200-sdramc" was missing from binding documentation.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
In response to the "undocumented compatible strings" message, here is a
patch which is adding the precision of two "chips" that should be used for
the "atmel,<chip>-aic" compatibility string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The 'max-speed' property is optional but defined in the ePAPR
specification and now supported by the Linux Device Tree parsing
infrastructure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booted with device tree, we may still have platform data passed
as auxdata. For am3517 this is needed for passing the interrupt_enable
and interrupt_disable callbacks that access the omap system control module
registers. These callback functions will eventually go away when we have
a separate system control module driver.
Some of the things that are currently passed as platform data we don't need
to set up as device tree properties as they are always the same on am3517.
So let's use a new compatible flag for those so we can get those from
the device tree match data.
Also note that we need to fix setting of phy_dev to NULL instead of an empty
string as the code later on uses that to find the first phy on the mdio bus.
This seems to have been caused by 5d69e0076a (net: davinci_emac: switch to
new mdio).
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This binding mainly serves to document the list of input and output pins
that may be used in a sound card's audio routing table.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Initially, this binding and driver only describe/support playback to
headphones and speakers, and capture from the external microphone, with
GPIO-based jack detection for the headphone jack only.
This driver is useful for the Venice2 board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is the first step to move AT91 to the CCF.
- core CCF and drivers for most of the clocks
- use of CCF for sama5d3 (100% DT-based)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSnLhVAAoJEAf03oE53VmQugkH/11ZuSaLsjn31/WvE4WwKdgc
RCIx7r8BCmPLNwDFOgc7tsheH7Jb6I7BNv4MnX8NIPrcAGy6yCEaD8TqhwKGTs9s
2YGoKB48fpwm1udDc6Hfq3/yqkPvM7AnzE1ei1rJNmLt2582tlX1FI+klQG5EoUK
23Pf4yjxtxt31s6xjuvRjEVjEat4PWnuVLs0nZWK6mizApXjA1JPIsKS6NL7q+eG
aBMWDGw0DW4M8VEHAZygxF16PRXnumuB7NAIxKp8SJW5/acSeQntJTNXisMQBem7
DxWfvK7WAFEBGUcRN33a9RpKaHg0Gur1If2sw6CkZ83RnRV9CLqURty1mO4WCUo=
=B+yP
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
AT91: Move to Common Clock Framework and sama5d3 implementation
This is the first step to move AT91 to the CCF.
- core CCF and drivers for most of the clocks
- use of CCF for sama5d3 (100% DT-based)
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91/dt: remove old clk material
ARM: at91: move sama5d3 SoC to common clk
ARM: at91/dt: define sama5d3xek's main clk frequency
ARM: at91/dt: define sama5d3 clocks
ARM: at91: prepare common clk transition for sama5d3 SoC
ARM: at91: prepare sama5 dt boards transition to common clk
ARM: at91: add new compatible strings for pmc driver
ARM: at91: move pit timer to common clk framework
dt: binding: add at91 clks dt bindings documentation
clk: at91: add PMC smd clock
clk: at91: add PMC usb clock
clk: at91: add PMC utmi clock
clk: at91: add PMC programmable clocks
clk: at91: add PMC peripheral clocks
clk: at91: add PMC system clocks
clk: at91: add PMC master clock
clk: at91: add PMC pll clocks
clk: at91: add PMC main clock
clk: at91: add PMC macro file for dt definitions
clk: at91: add PMC base support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in post-rc1 fixes that have gone into rc2/3 to avoid later conflicts.
* commit 'fixes': (39 commits)
arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
arm: socfpga: Enable ARM_TWD for socfpga
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
ARM: multi_v7_defconfig: enable network for BeagleBone Black
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add "arm,gic-400" compatible property for ARM GIC-400 IP.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Acked-by: Kumar Gala <galak@codeaurora.org>
Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from board
files to DT. Tony thinks this was the last major set of fixes, with
maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed PCIe
hardware, i.e. incorrect number of busses on some SoCs, etc. The line
delta adds up due to various ranges moving around when this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in my
test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91, a couple
of reverts for ux500, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=PljB
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another batch of fixes for ARM SoCs for 3.13. The diffstat is large,
mostly because of:
- Another set of fixes to fix regressions caused by moving OMAP from
board files to DT. Tony thinks this was the last major set of
fixes, with maybe just a few small patches to follow.
- More fixes for Marvell platforms, most dealing with misdescribed
PCIe hardware, i.e. incorrect number of busses on some SoCs, etc.
The line delta adds up due to various ranges moving around when
this is fixed.
But there's also:
- Some smaller tweaks to defconfigs to make more boards bootable in
my test setup for better coverage.
- There are also a few other smaller fixes, a short series for at91,
a couple of reverts for ux500, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
arm: dts: socfpga: Change some clocks of gate-clk type to perip-clk
arm: socfpga: Enable ARM_TWD for socfpga
ARM: multi_v7_defconfig: enable SDHCI_BCM_KONA and MMC_BLOCK_MINORS=16
ARM: sunxi_defconfig: enable NFS, TMPFS, PRINTK_TIME and nfsroot support
ARM: multi_v7_defconfig: enable network for BeagleBone Black
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
...
This moves the External Bus Interface (EBI) over to a device
tree node and deletes the static mappings from the platform.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch changes the cpufreq-cpu0 driver to consider if
a cpu needs cooling (with cpufreq). In case the cooling is needed,
the cpu0 device tree node needs to be properly configured
with cooling device properties.
In case these properties are present,, the driver will
load a cpufreq cooling device in the system. The cpufreq-cpu0
driver is not interested in determining how the system should
be using the cooling device. The driver is responsible
only of loading the cooling device.
Describing how the cooling device will be used can be
accomplished by setting up a thermal zone that references
and is composed by the cpufreq cooling device.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: cpufreq@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch introduces a device tree bindings for
describing the hardware thermal behavior and limits.
Also a parser to read and interpret the data and feed
it in the thermal framework is presented.
This patch introduces a thermal data parser for device
tree. The parsed data is used to build thermal zones
and thermal binding parameters. The output data
can then be used to deploy thermal policies.
This patch adds also documentation regarding this
API and how to define tree nodes to use
this infrastructure.
Note that, in order to be able to have control
on the sensor registration on the DT thermal zone,
it was required to allow changing the thermal zone
.get_temp callback. For this reason, this patch
also removes the 'const' modifier from the .ops
field of thermal zone devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Enable common clock driver of Hi3620 SoC. clkgate-seperated driver is
used to support the clock gate that enable/disable/status registers
are seperated.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This patch adds device tree support to the PXA's PWM driver. Nothing
needs to be extracted from the device tree node by the PWM device.
Client devices need only specify the period; the per-chip index is
implicitly zero because one device node must be present for each PWM
output in use. This approach is more convenient due to the wide
variability in the number of PWM channels present across the various PXA
variants, and is made possible by the fact that the register sets for
each PWM channel are segregated from each other. An of_xlate() method
is added to parse this single-cell node. The existing ID table is
reused for the match table data.
Tested on a Palm Treo 680 (both platform data and DT cases).
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
- Fix up tc3589x bindings so this chip works again.
- Remove SSP platform devices, as we now boot from device tree
exclusively.
- Delete surplus AB8500/DB8500 platform data, not obtained from
the device tree.
- Add DMA config for the MSP devices.
- A series of 21 patches moving pin control config for the
on-chip Nomadik pin controller from the board file
to the device tree, step by step.
- Two patches to the STE DMA40 driver regarding the high-prio
DMA channel so this can be moved to the device tree. Both have
Vinod's ACK.
- Decommission of the non-device tree boot path for the timer
initialization code.
- Deletion of the non-devicetree probe path from the MTU timer
driver, as all platforms using it are now using device tree.
This has Daniel Lezcano's ACK.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSlQIFAAoJEEEQszewGV1zaaoP/iUClda7fps7dhBZMHOaDr48
DAe9yBaUoGBgyjOd0QUUP4/P5PxsXQVCM13gdaITt+R4eg8XYxG3jLNxopMfGKYV
bifbXqEd4wf0t8yUYCzhdfAeWchzSph3W2C7I2hW09b9nhJ+RWgXdzcO061E9Tbj
BbZ4aS7IR3HfXzQ/zdMBtlbNXkWtn++HXCjC5Z0t0FKqSL7X8LKZrr3GEHZ6vfnB
sI5/bTK3AfXt7h2wsu4z/IZK89Ttt9AATNhxajW2Pptkuggc+/KfRRDyYeZFBT70
9KIRsF3NXSsOhOYcRNbWjNU2S8OtC7UyKMB5+y07cYU53ehaiEH8tUMait1cphlc
kFJAqKXY87I85E6WTEgv1s4Q8H3rQzVc/IjT3LODFbuM3MeTrsrnbKDeFCOqqpJC
4Ggq6VBXhn7G2srcM5KBYZcZhmq86qhmo0/vUOqaYcdmgdD7KJyewLNafYf5W+DX
JxVlnzpdWsAhihUV3oBeJybM0YGvE1wa855ZqbsAZ8nrLTBoTD+zi30mIhXrQwQp
v54ywGa0JtjpTLY6EZG2Rptq4qOUVUbkuNSv+3BYgVTqxCcCqXOu+tuzGk2O1jTh
8/2biKCCrdbSWCmbMZDi7jlkO5ywqcn2Brav5KyZ+bCwITRybfoxeOv6f8DCT741
bwx00XNaYVO/H+Vptd+h
=w9pg
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Ux500 device tree patches for v3.14, take one:
- Fix up tc3589x bindings so this chip works again.
- Remove SSP platform devices, as we now boot from device tree
exclusively.
- Delete surplus AB8500/DB8500 platform data, not obtained from
the device tree.
- Add DMA config for the MSP devices.
- A series of 21 patches moving pin control config for the
on-chip Nomadik pin controller from the board file
to the device tree, step by step.
- Two patches to the STE DMA40 driver regarding the high-prio
DMA channel so this can be moved to the device tree. Both have
Vinod's ACK.
- Decommission of the non-device tree boot path for the timer
initialization code.
- Deletion of the non-devicetree probe path from the MTU timer
driver, as all platforms using it are now using device tree.
This has Daniel Lezcano's ACK.
* tag 'ux500-devicetree-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (39 commits)
ARM: ux500: decomission custom SMP TWD timer init
clksrc: delete nomadik MTU non-DT boot path
ARM: ux500: decomission the non-DT MTU init sequence
dma: ste_dma40: Parse flags property for new 'high priority channel' request
dma: ste_dma40: Expand DT binding to accept 'high-priority channel' flag
ARM: ux500: Remove checking for DT during timer init
ARM: ux500: Clean-up legacy extern prototype
ARM: ux500: Remove unused call to register AMBA devices
ARM: ux500: Clean-up non-DT IRQ initialisation
pinctrl: nomadik: decomission non-DT boot path
pinctrl: nomadik: move platform data handling into driver
ARM: ux500: get rid of unused header
ARM: ux500: delete Nomadik pinctrl AUXDATA
ARM: ux500: delete remnant pin config macros
ARM: ux500: move snowball pin configs to device tree
ARM: ux500: move snowball LED pin control to device tree
ARM: ux500: convert Snowball SPI pin reference
ARM: ux500: move snowball ethernet config to device tree
ARM: ux500: move HREFv60plus pin configs to device tree
ARM: ux500: move final HREFv60 LCD pins to device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
The DWC2 USB controller in the BCM2835 (Raspberry Pi) needs some non-
default parameters. Select these based on the compatible value from the
DT node. For all other HW, fall back to the default parameters currently
in use.
The values in params_bcm2835[] were posted to the mailing list by Paul
quite some time ago. I made a couple of minor modifications since then;
to set ahbcfg instead of ahb_single, and to set uframe_sched.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The r8a7791 (R-Car M2) has a GPIO controller with additional features
compared to the generic renesas,gpio-rcar compatible devices. Add a
model-specific string to let the driver enable these features.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
re-format and re-word the device tree binding documentation for MPC8xxx
and compatibles, reference the common document for interrupt controllers
and remove outdated duplicate SoC specific information
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <Pawel.Moll@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: <devicetree@vger.kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This binding shouldn't exist; Tegra20 has two forms of SPI controller
that are documented separately in nvidia,tegra20-sflash.txt and
nvidia,tegra20-slink.txt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
This patch fix typo of property name from 'pullup-uV' to 'pullup-uv'.
The ntc_thermistor.c use 'pullup-uv' when parsing dt data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Adding Global Mixed-mode Technology Inc. to the list
of devicetree vendor prefixes.
Signed-off-by: Wei Ni <wni@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
phy-supply is an optional property of the fec driver, so add it to the binding
documentation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The binding and support for omap5-mpu which has a cortex-a15
smp core, gic and integrated L2 cache has been existing for sometime.
So Documenting the missing binding here.
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
These bindings can be used to register SATA devices found on R-Car SoC.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds new at91 clks dt bindings documentation.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Support for loading the simple-card module via DeviceTree.
It requests CPU/CODEC information.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The required properties are not named "div" and "mult",
but rather "clock-div" and "clock-mult".
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds a new driver for the beeper controlled via GPIO pin.
The driver does not depend on the architecture and is positioned as
a replacement for the specific drivers that are used for this function.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some features can be configured by the companion I2C chips,
which may not be available at the probe time. Fix the issue
by returning -EPROBE_DEFER when the MMC controller slots
are not configured.
While at it, let's also add minimal device tree support so
omap24xx platforms can use this driver without legacy mode
since we claim to support device tree for mach-omap2 based
systems.
Although adding the minimal device tree support is not strictly
a fix, it does remove one of the last blockers for dropping a
bunch of legacy platform data for mach-omap2.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is used for MSP (audio) devices which is about to be fully DT:ed.
Cc: devicetree@vger.kernel.org
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on OMAP,
finding new breakage of things that don't work quite right yet without
the traditional board files. I expect a bit more of this to come in this
release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec work and
to stop the MCPM core to produce a warning (the warning was new to 3.13-rc1).
- A handful of minor fixes for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zdhe
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on
OMAP, finding new breakage of things that don't work quite right
yet without the traditional board files. I expect a bit more of
this to come in this release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec
work and to stop the MCPM core to produce a warning (the warning
was new to 3.13-rc1).
- A handful of minor fixes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm2835: add missing #xxx-cells to I2C nodes
ARM: dts: Add max77686 RTC interrupt to cros5250-common
ARM: vexpress/TC2: Implement MCPM power_down_finish()
ARM: tegra: Provide dummy powergate implementation
ARM: omap: fix warning with LPAE build
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
This mostly consists of patches that didn't quite make the last cycle. Lots
of interesting things under review currently.
Core:
- Add devm_iio_device_register/unregister. I took some convincing on whether
there would be many devices that really were simple enough to need no
explicit actions on removal. Turns out there are some.
- Move some stray docs to above the relevant implemenation.
- Drop a redundant repeated check on the fact the trigger has actually changed
when there is a userspace attempt change it.
Drivers:
New drivers
- Freescale MPL3115A2 Pressure / temperature sensor
New functionality
- hid_sensors: add sensitivity support.
DT bindings
- tsl2563
- hmc5843
Cleanups
- Drop unused scan_type from viperboard adc driver.
- devm_iio_device_register used in viperboard, ad5421, ad5755, adis16130,
adxrs450, vcnl4000, adis16220, ad7816, lpc32xx, adt7316, adis16060, isl29018
and ad2s1200. Note that this was proposed in a number of other drivers
and this revealed a number of missorderings in remove functions. Also for
now I have blocked this on any device that any hardware suspend suport on
the basis that we probably want to power down devices if they have no driver
support loaded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KZou
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new features, drivers and cleanups for IIO in the 3.14 cycle.
This mostly consists of patches that didn't quite make the last cycle. Lots
of interesting things under review currently.
Core:
- Add devm_iio_device_register/unregister. I took some convincing on whether
there would be many devices that really were simple enough to need no
explicit actions on removal. Turns out there are some.
- Move some stray docs to above the relevant implemenation.
- Drop a redundant repeated check on the fact the trigger has actually changed
when there is a userspace attempt change it.
Drivers:
New drivers
- Freescale MPL3115A2 Pressure / temperature sensor
New functionality
- hid_sensors: add sensitivity support.
DT bindings
- tsl2563
- hmc5843
Cleanups
- Drop unused scan_type from viperboard adc driver.
- devm_iio_device_register used in viperboard, ad5421, ad5755, adis16130,
adxrs450, vcnl4000, adis16220, ad7816, lpc32xx, adt7316, adis16060, isl29018
and ad2s1200. Note that this was proposed in a number of other drivers
and this revealed a number of missorderings in remove functions. Also for
now I have blocked this on any device that any hardware suspend suport on
the basis that we probably want to power down devices if they have no driver
support loaded.
Add device tree support for twl4030 power button driver.
Adding device tree support involved converting the
driver to module_platform_driver().
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sachin Kamat