Commit Graph

59 Commits

Author SHA1 Message Date
Simon Wunderlich 855aed1220 ath10k: add spectral scan feature
Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.

Essentially, to try it out:

ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples

This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.

Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-08-04 09:07:54 +03:00
Michal Kazior 24c88f7807 ath10k: add support for 10.2 firmware
The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.

The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-07-28 23:48:03 +03:00
Janusz Dziedzic d385623a78 ath10k: add implementation for configure max amsdu, ampdu
Allow to setup maximum subframes for AMSDU and AMPDU aggregation
via debugfs htt_max_amsdu_ampdu file.

Eg.
echo "2 64" > htt_max_amsdu_ampdu
will setup maximum amsdu subframes equal 2 and
maximum ampdu subframes equal to 64.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-07-14 15:44:48 +03:00
Michal Kazior 6782cb696d ath10k: make core registering async
If ath10k was built into the kernel it could stall
booting for 120 seconds by default (60 seconds for
each firmware API variant) waiting for firmware
files before userspace was ready or filesystems
mounted.

Fix this by making the core registering
asynchronous.

This also shoves off about 1 second from boot time
on most systems since the driver is now mostly
initialized in a worker and modprobe takes very
little time to complete.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-26 12:44:44 +03:00
Ben Greear 46acf7bb9b ath10k: support get/set antenna configurations.
Verified that target's tx/rx chain register is set appropriately,
and that the tx rate goes down as number of chains
decrease, but I did not actually try to verify antenna
ceased to transmit when disabled.

kvalo: move ar->supp_*_chainmask initialisation to ath10k_mac_register()

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-05-22 19:55:09 +03:00
Michal Kazior d650097bfa ath10k: refactor radar detection code
If 20MHz CAC completed successfully then
subsequent CAC with wider bandwidth (40Mhz, 80Mhz)
with identical control frequency did not start
monitor vdev making it impossible to detect any
radar pulses during intended CAC.

It also was incorrect to assume ath10k_config() will
be called after CAC is finished. Theoretically for
non-HT channels nothing changes between CAC and
start_ap() (albeit in practice this can be
different). The incorrect assumption led to CAC
not being stopped on non-HT chandefs leading to
all Rx being drooped making it impossible for
clients to associate.

While at it clean up the code a bit.

kvalo: separate WARN_ON() from the if statement

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-11 08:35:25 +03:00
Michal Kazior 1bbc09752d ath10k: refactor monitor code
It was possible to create/delete/start/stop
monitor vdev from a few places that were not
exclusively protected against each other. This
resulted in monitor vdev being stopped/removed by
one call origin while another one was expecting it
to continue running.

For example if CAC was started and interface's
promiscuous mode was toggled monitor vdev was
removed from the driver meaning no radar would be
detected. In additional a warning would be printed
upon CAC completion complaining it tried to stop
non-running monitor vdev.

The patch simplifies monitor code by removing
IEEE80211_HW_WANT_MONITOR_VIF (which wasn't really
ever needed) and improves state tracking. It also
unifies prints.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-04-08 09:55:30 +03:00
Chun-Yeow Yeoh 52e346d1e7 ath10k: add extra pdev stats on 10.1 firmware
As pointed out by Michal Kazior, add extra pdev stats
for 10.1 firmware.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 17:00:00 +02:00
Ben Greear 23c3aae4a0 ath10k: add the Rx rate in FW stats
FW stats does provide the Rx rate information. Add this.
Tested with firmware 10x firmware.

Increase buffer size so more peers can be shown.

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-28 16:58:50 +02:00
Marek Kwaczynski e81bd10482 ath10k: add recalc RTS/CTS protection method
Add recalculation of RTS/CTS protection when one or more legacy
stations are connected to ath10k. In this case enable RTS/CTS
protection and set sw retry profile are needed in the FW.
Without this change legacy station is starved and has very low
throughput.

Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-03-13 07:14:28 +02:00
Michal Kazior a16942e630 ath10k: bypass htc for htt tx path
Going through full htc tx path for htt tx is a
waste of resources. By skipping it it's possible
to easily submit scatter-gather to the pci hif for
reduced host cpu load and improved performance.

The new approach uses dma pool to store the
following metadata for each tx request:
 * msdu fragment list
 * htc header
 * htt tx command

The htt tx command contains a msdu prefetch.
Instead of copying it original mapped msdu address
is used to submit a second scatter-gather item to
hif to make a complete htt tx command.

The htt tx command itself hands over dma mapped
pointers to msdus and completion of the command
itself doesn't mean the frame has been sent and
can be unmapped/freed. This is why htc tx
completion is skipped for htt tx as all tx related
resources are freed upon htt tx completion
indication event (which also implicitly means htt
tx command itself was completed).

Since now each htt tx request effectively consists
of 2 copy engine items CE_HTT_H2T_MSG_SRC_NENTRIES
is updated to allow maximum of
TARGET_10X_NUM_MSDU_DESC msdus being queued. This
keeps the tx path resource management simple.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:59:17 +02:00
Michal Kazior 7676a88876 ath10k: remove is_aborted from skb_cb
The flag wasn't used anymore. No need to keep it.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:58:53 +02:00
Michal Kazior 767d34fc67 ath10k: remove DMA mapping wrappers
There's no real benefit from using them. DMA-API
already provides debugging. Some skbuffs are
already mapped directly with DMA-API since wrapper
arguments were insufficient and extending them
would be pointless.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-28 11:58:38 +02:00
Janusz Dziedzic 9f81f72556 ath10k: bitrate_mask add force_sgi support
Add force SGI support.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-27 18:40:37 +02:00
Michal Kazior 9797febc4c ath10k: implement sta_rc_update()
This allows dynamic changes of bandwidth/nss/smps,
e.g. via ht/vht operation mode change
notification.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-15 08:49:02 +02:00
Marek Puzyniak 00f5482bcd ath10k: suspend hardware before reset
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.

This patch depends on
ath10k: fix device initialization routine

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 17:24:17 +02:00
Marek Puzyniak 9042e17df8 ath10k: refactor suspend/resume functions
Suspend/resume callbacks are not protected by configuration mutex
so adding such protection. Also in order to simplify implemetation
of suspend function wait queue is replaced by completion.

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-02-13 17:24:01 +02:00
Michal Kazior 748afc4735 ath10k: implement and use new beacon method
Until now ath10k used a copy-by-value beacon
submission.

The new method passes a DMA address via WMI
command only. This command contains additional
metadata that fixes AP behaviour with regard
to powersave buffering.

This also fixes strange bug when multicast traffic
would freeze TX indefinitely.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-01-24 10:23:37 +02:00
Michal Kazior c930f744bd ath10k: implement channel switching
Until now channel change wasn't propagating to FW
directly because operational channel is abstracted
by VDEVs and it wasn't really necessary since
ath10k implements hwscan and hwroc.

This effectively fixes STA CSA and allows for
future AP-like CSA as well.

kvalo: change error handling in ath10k_bss_info_changed()

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-01-24 10:22:19 +02:00
Kalle Valo 5a13e76eca ath10k: enable firmware STA quick kickout
Firmware has a feature to track if the associated STA is not acking the frames.
When that happens, the firmware sends WMI_PEER_STA_KICKOUT_EVENTID event to the
host. Enable that to faster detect when a STA has left BSS without sending a
deauth frame.

Also set huge keepalive timeouts to avoid using the keepalive functionality in
the firmware.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-01-23 14:54:03 +02:00
Janusz Dziedzic 51ab1a0a09 ath10k: add set_bitrate_mask callback
Add set_bitrate_mask callback. Currently
ath10k HW is limited to handle only single
fixed rate setting or limit number of used
spatial streams.

Example:
iw wlanX set bitrates legacy-5 ht-mcs-5 vht-mcs-5 2:9
will setup VHT, nss=2, mcs=9

iw wlanX set bitrates legacy-5 18 ht-mcs-5 vht-mcs-5
will setup legacy, 18Mbps

iw wlanX set bitrates legacy-5 ht-mcs-5 3 vht-mcs-5
will setup HT, nss=1, mcs=3

iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9
will setup nss=1

iw wlanX set bitrate legacy-5 ht-mcs-5 vht-mcs-5 1:0-9 2:0-9
will setup nss=2

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-01-10 11:54:49 +02:00
Kalle Valo f118a3e515 ath10k: add debugfs file to control firmware dbglog
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:

echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog

And to put back firmare defaults use 0x0:

echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-01-10 11:49:46 +02:00
Bartosz Markowski 0e759f363e ath10k: track number of existing peers
To not exceed number of allowed clients (AP mode), make sure to
check how many of them are already on the peers list.

10.X firmware support up to 127 peers, non-AP centric firmwares 16.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2014-01-10 11:46:47 +02:00
Bartosz Markowski d354181f4d ath10k: introduce NO_P2P fw feature flag
Not each ath10k FW track supports P2P (10.X for instance does not)
This new firmware feature flag allows to turn off P2P interface type.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-12-16 16:03:25 +02:00
Kalle Valo 650b91fb09 ath10k: show hardware and firmware info prints only once
This makes ath10k a lot less spammy by default.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20 10:34:59 +02:00
Marek Puzyniak 7d9b40b461 ath10k: add debugfs file to control radar events blocking
Sometimes for DFS testing is required to stay on current channel even after
radar detected. This patch allows to enable/disable radar detected event to be
passed to mac80211.

By default radar detected event in not blocked.

To block it:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events

To unblock again:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events

Inform about blocking radar detected event even when logs are disabled
for throughput/performance reasons.

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20 10:34:59 +02:00
Marek Puzyniak e8a50f8ba4 ath10k: introduce DFS implementation
Configure interface combination for AP running on channels
where radar detection is required. It allows only one type
of interface - AP on DFS channel and limits number of AP
interfaces to 8. Setup WMI channel flags accordingly to mac
channel configuration. CAC based on additional monitor vdev
is started if required for current channel.

kvalo: dropped ATH10K_DFS_CERTIFIED config option as this
the DFS still depends on few mac80211 and cfg80211 patches
which are on mac80211-next.git right now. The config option
will be added later once all dependencies are available.

Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20 09:59:47 +02:00
Janusz Dziedzic 9702c68608 ath10k: add phyerr/dfs handling
Handle phyerr, dfs event, radar_report and fft_report.
Add also debugfs dfs_simulate_radar and dfs_stats files.
Use ath dfs pattern detector.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-20 09:59:41 +02:00
Bartosz Markowski 7109861573 ath10k: expand the wmi mgmt queue limit to 128
It was obseverd many times the short queue limit can be
easily exceeded in case of AP multiple BSSID scenarios.

"ath10k: wmi mgmt_tx queue limit reached."

This was leading to TX packets drops.

This patch expands the queue limit to 128. After many stress
experiments (high traffic and lot of management frames in
the air) the new value seems to fix the problem on platforms
with limited resources.

Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-11-15 11:01:27 +02:00
Michal Kazior 0579119f7d ath10k: track vif list internally
mac80211 interface interations functions have
peculiar locking issues. This patch introduces
internal (to ath10k) vif list that will be used
for vif iteration purposes.

kvalo: remove extra INIT_LIST_HEAD()

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-16 15:44:45 +03:00
Michal Kazior cc4827b97b ath10k: use workqueue to set WEP TX key
Recent WMI/HTC changes made it possible for WMI
commands to sleep (if there's not enough HTC TX
credits to submit a command). TX path is in an
atomic context so calling WMI commands in it is
wrong.

This simply moves WEP key index update to a worker
and fixes the 'scheduling while atomic' bug.

This still leaves multiple WEP key handling laggy,
i.e. some frames may be TXed with an old/different
key (although recipient should still be able to RX
them).

kvalo: changed the title

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-10-16 15:44:45 +03:00
Kalle Valo 1a222435a1 ath10k: implement firmware IE container support
Firmware IE containers can dynamically provide various information what
firmware supports. Also it can embed more than one image so updating firmware
is easy, user just needs to update one file in /lib/firmware/.

The firmware API 2 or higher will use the IE container format, the current API
1 will not use the new format but it still is supported for some time. FW API 2
files are named as firmware-2.bin (which contains both firmware and otp images)
and API 1 files are firmware.bin and otp.bin.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-30 22:03:31 +03:00
Kalle Valo 958df3a00a ath10k: store separate pointers for firmware data
Needed for firmware IE formatted images.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-30 22:03:31 +03:00
Kalle Valo 365279167c ath10k: rename board_data in struct ath10k
I will use board_data for something else in the following patch
so I need to rename it.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-30 22:03:31 +03:00
Bartosz Markowski 226a339ba8 ath10k: introduce dynamic pdev parameters
This is done exactly the same way as for vdev.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-27 14:58:15 +03:00
Bartosz Markowski 6d1506e788 ath10k: introduce dynamic vdev parameters
Both firmwares (main and 10.x) have different set of vdev
parameters. To stay in sync with FW API, this patch introduces
a dynamic registering method.

ath10k_wmi_vdev_set_param() takes now indirect u32 value
to identify the Vdev parameter it want's to set.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-27 14:58:15 +03:00
Bartosz Markowski 5e00d31a0f ath10k: bring back the WMI path for mgmt frames
This is still the only way to submit mgmt frames in case
of 10.X firmware.

This patch introduces wmi_mgmt_tx queue, because of the
fact WMI command can block. This is a problem for
ath10k_tx_htt(), since it's called from atomic context.
The skb queue and worker are introduced to move the mgmt
frame handling out of .tx callback context and not block.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-27 14:58:14 +03:00
Bartosz Markowski b3effe61a1 ath10k: implement host memory chunks
10.X firmware can request a memory pool from host to offload
it's own resources. This is a feature designed especially
for AP mode where the target has to deal with large number
of peers.

So we allocate and map a consistent DMA memory which FW can
use to store e.g. peer rate contol maps.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-27 14:58:14 +03:00
Bartosz Markowski ce42870efb ath10k: introduce dynamic WMI structures
This is the initial framework to implement dynamic
WMI API in order to support new firmware (from so
called 10.X branch)

The realization is to have a static WMI cmd map for
each of the firmwares, registered upom wmi init.

This patch creates such map for MAIN FW, updates
wmi_cmd_send() calls to take as a parameter
the map value instead of direct WMI enum.

As soon as complete 10.X API will be on place,
we will introduce the FW IE mechanics to dynamicaly
identify which FW is being used and based on that
we will use correct map, API, structures, etc.

Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-27 14:58:13 +03:00
Michal Kazior 1f8bb1518e ath10k: use msdu headroom to store txfrag
Instead of allocating sk_buff for a mere 16-byte
tx fragment list buffer use headroom of the
original msdu sk_buff.

This decreases CPU cache pressure and improves
performance.

Measured improvement on AP135 is 560mbps ->
590mbps of UDP TX briding traffic.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-20 08:18:10 +03:00
Michal Kazior 0a89f8a01d ath10k: decouple HTT TX completions
Until now the all MSDU transfer related structures
were freed when all resources were unreferenced.

Now HTC transfer is freed independently and HTT
transfer is so too.

This yields a way more simpler ath10k_skb_cb and
should possibly enable parallel pipe processing
(which is now serialized in
ath10k_pci_process_ce routine).

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-20 08:18:09 +03:00
Michal Kazior 5c6c82df6b ath10k: remove wmi event worker thread
It's not really necessary to have this processed
in a worker. There are no sleepable calls (and
actually shouldn't be).

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-16 19:47:46 +03:00
Michal Kazior 7cc2301636 ath10k: remove wmi pending count limit
It is no longer used nor necessary since WMI
commands can block.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-16 19:47:46 +03:00
Michal Kazior ed54388a38 ath10k: improve beacon submission latency
The patch prevents beacon misses in some case of
heavy load on a system.

If a beacon can't be transmitted directly from an
SWBA event it will be left in arvif->beacon and
transmission will be retried once TX credits
become available.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-16 19:47:46 +03:00
Michal Kazior be8b394390 ath10k: make WMI commands block by design
This will be necessary for further changes in
command submission scheme.

Once HTC is cleaned up WMI commands will finally
block.

This requires for SWBA to be processed in a
non-atomic context for now. Once other necessary
changes are in this will be reverted.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-16 19:47:46 +03:00
Kalle Valo a3d135e566 ath10k: add htt_stats_enable debugfs file
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-06 12:42:26 +03:00
Kalle Valo e01ae68c5d ath10k: check chip id from the soc register during probe
ath10k doesn't support qca988x hw1.0 boards anymore. Unfortunately
the PCI id is the same in hw1.0 and hw2.0 so ath10k tries to use
hw1.0 boards anyway. But without hw1.0 workarounds in place
ath10k just crashes horribly.

To avoid using hw1.0 boards at all add a chip id detection
and fail the probe if hw1.0 is detected:

[ 5265.786408] ath10k: ERROR: qca988x hw1.0 is not supported
[ 5265.786497] ath10k: Unsupported chip id 0x043200ff
[ 5265.786574] ath10k: could not register driver core (-95)
[ 5265.793191] ath10k_pci: probe of 0000:02:00.0 failed with error -95

Also add a warning if there's an unknown chip id but continue
the boot process normally anyway.

Reported-by: Zaki Bakar <zaki.bm@gmail.com>
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-09-03 09:54:16 +03:00
Michal Kazior 0d9b0438b6 ath10k: add support for firmware newer than 636
The mgmt_rx event structure has been expanded.
Since the structure header is expanded the payload
(i.e. mgmt frame) is shifted by a few bytes. This
needs to be taken into account in order to support
both old and new firmware.

This introduces a fw_features to keep track of any
FW-related ABI/behaviour changes.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-08-15 16:04:41 +03:00
Michal Kazior 2e1dea4051 ath10k: implement get_survey()
This implements a limited subset of what can be
reported in the survey dump.

This can be used for assessing approximate channel
load, e.g. for automatic channel selection.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-08-02 09:35:21 +03:00
Michal Kazior 8865bee483 ath10k: detect the number of spatial streams supported by hw
Until now ath10k assumed 3 spatial streams.
However some devices support only 2 spatial
streams.

This patch improves performance on devices that
don't support 3 spatial streams.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2013-07-31 09:03:56 +03:00