Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples
This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.
The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It always bugged me how tid is computed and stored
in a temporary var before written to the control
buffer. It was confusing and it made it difficult
to work with tx helpers.
While at it rename the qos workaround function as
it was misleading - it's not a workaround but
preparation for nwifi tx mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to call hif_stop() 2 times through
ath10k_htc_connect_init() timeout failpath which
could lead to double free_irq() kernel splat for
multiple MSI interrupt case.
Re-order init sequence to avoid this problem. The
HTC stop shouldn't stop HIF implicitly since it
doesn't implicitly start it. Since the re-ordering
required some functions to be split/removed/renamed
rename a few functions to make more sense while at
it.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix sending and receiveing protected managment frames.
Lack of protected flag for received protected action frames
causes report these frames as unprotected robust action frames.
If the driver in AP mode sent frame with protected flag and
CCMP header using IEEE80211_KEY_FLAG_SW_MGMT_TX flag,
the FW encrypted frames once again. From user side all
received SA Query Requests and Responses were skipped and
all protected action frames were sent as malformed packets.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DMA mapping of next beacon failed ath10k leaked
the beacon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DMA mapping of next beacon failed it was
possible for next SWBA to access a pointer that
was already unmapped and freed. This could cause
memory corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They were just too superfluous and made it harder to read logs. Change them to
follow the normal style used in ath10k.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Regulatory domain settings for firmware 10.x has more options
than main firmware, so handle regulatory domain setup separately
for both supported firmwares. Fill in additional dfs domain
parameter according to current regulatory.
This patch does not solve any known bug. Not handled parameter
for firmware 10.x was found during code review.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
IBSS mode requires the changing of supported rate. Do this
by reassociate the peer. The investigation shows that if move
from legacy to HT, the rate control won't work after changing
the supported rate. But once changing the supported rate to HT,
user can assign the TxRate in HT mode.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Seems like we have an old bug, where we incidently overwrites
the max_antenna_gain we pass to firmware, with zero value.
End of all we are artifically reducing the output power.
This patch removes the excessive assignment on max_antenna_gain,
which is being provided by regulatory domain, and consequently
improves the tx power.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no real benefit from using them. DMA-API
already provides debugging. Some skbuffs are
already mapped directly with DMA-API since wrapper
arguments were insufficient and extending them
would be pointless.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of warm reset target need to be suspended.
Suspend function is extented to handle both cases
with disabling interrupts and without disabling interrupts.
Warm target reset requires suspend with all interrupts
disabled.
This patch depends on
ath10k: fix device initialization routine
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Show message length and expected length. Helps debug
firmware mismatch issues.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ARP frames exchange does not work properly for UAPSD enabled AP.
ARP requests which arrives with access category 0 are processed
by network stack and send back with access category 0. FW changes
access category to 6. This is causing problems when UAPSD associated
STA is sleeping after has sent ARP request. Configure ARP access
category in FW to best effort (0) solves this problem. ARP frames
will be send with access category 0.
Simplify arp ac override functionality by removing redundant entry in
pdev param maping table. There should be only one entry in pdev param
map but enum has different name for different FW.
kvalo: change the warning message
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Until now ath10k used a copy-by-value beacon
submission.
The new method passes a DMA address via WMI
command only. This command contains additional
metadata that fixes AP behaviour with regard
to powersave buffering.
This also fixes strange bug when multicast traffic
would freeze TX indefinitely.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Most channel switching logic has been implemented
already so this patch is pretty small. The patch
makes use of mac80211's vif->csa_active for AP CSA
handling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware has a feature to track if the associated STA is not acking the frames.
When that happens, the firmware sends WMI_PEER_STA_KICKOUT_EVENTID event to the
host. Enable that to faster detect when a STA has left BSS without sending a
deauth frame.
Also set huge keepalive timeouts to avoid using the keepalive functionality in
the firmware.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable ap_ps_peer_param_cmdid for 10.x FW.
This is used mainly for AP UAPSD.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:
echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
And to put back firmare defaults use 0x0:
echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware can send simple ascii strings as debug messages using
WMI_DEBUG_PRINT_EVENTID, print those with ATH10K_DBG_WMI log level.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Although CCK modulation isn't expected for 11a if
it happened it made ath10k report wrong band
(2GHz) for a mgmt frame that were actually
received on 5Ghz band. Frequency would also
decoded incorrectly too.
In case of 5GHz-only devices this triggered
mac80211 WARN_ON because there was no according
sband pointer to be found.
The patch should fix delivery of such frames by
using different means to acquire band parameter.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames received from FW were treated incorrectly.
This led to stations being unable to associate to
WEP Shared ath10k AP. This was indicated by a
bizarre hostapd message:
Unsupported authentication algorithm (36088)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes for DFS testing is required to stay on current channel even after
radar detected. This patch allows to enable/disable radar detected event to be
passed to mac80211.
By default radar detected event in not blocked.
To block it:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
To unblock again:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events
Inform about blocking radar detected event even when logs are disabled
for throughput/performance reasons.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Configure interface combination for AP running on channels
where radar detection is required. It allows only one type
of interface - AP on DFS channel and limits number of AP
interfaces to 8. Setup WMI channel flags accordingly to mac
channel configuration. CAC based on additional monitor vdev
is started if required for current channel.
kvalo: dropped ATH10K_DFS_CERTIFIED config option as this
the DFS still depends on few mac80211 and cfg80211 patches
which are on mac80211-next.git right now. The config option
will be added later once all dependencies are available.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle phyerr, dfs event, radar_report and fft_report.
Add also debugfs dfs_simulate_radar and dfs_stats files.
Use ath dfs pattern detector.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If beacon tx command failed the wmi command buffer
was not freed. This led to OOM in the long run.
This became aparent when stress testing
multi-BSSID.
Reported-By: Tomasz Skapski <tomasz.skapski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
sk_buff was not freed in some cases. The patch
unifies the msdu freeing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes incorrect values being printed on
big-endian hosts.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_wmi_cmd_send() will now sleep if there are no credits available.
To make it easier to catch callers in atomic context add might_sleep()
to the function.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return -EOPNOTSUPP if given parameter is not supported by firmware.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rename WMI_CMD_UNDEFINED to WMI_CMD_UNSUPPORTED. This is more
accurate here. Also return -EOPNOTSUPP instead of -EINVAL in
wmi_cmd_send().
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.X firmware does not support WMI_VDEV_PARAM_TX_ENCAP_TYPE.
It's a known limitation and we should not warn about this.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h
Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."
As to the ath10k bits, Kalle says:
"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."
And also:
"Major changes are:
* throughput improvements including aligning the RX frames correctly and
optimising HTT layer (Michal)
* remove qca98xx hw1.0 support (Bartosz)
* add support for firmware version 999.999.0.636 (Michal)
* firmware htt statistics support (Kalle)
* fix WEP in AP and IBSS mode (Marek)
* fix a mutex unlock balance in debugfs file (Shafi)
And of course there's a lot of smaller fixes and cleanup."
For the wl12xx bits, Luca says:
"Here are some patches intended for 3.13. Eliad is upstreaming a bunch
of patches that have been pending in the internal tree. Mostly bugfixes
and other small improvements."
Along with that...
Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates. As usual, there are a number of other small updates
from a variety of players as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It was observed few times, the artificial max_scan limit we
are using mainly to detect FW hangs, can be not enough for
instance while being associated and during heavy traffic.
What we do if the FW won't return with scan results within
the max_time time is a scan abort.
This is especially visible with 10.X fw which in combination
with dual band HW (scanning 32 channels) can end up with
hw_scan close to 10 seconds.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since the WMI API has been added and we can detect from the
FW IEs what firmware variant we deal with, turn on support
for 10.x firmware branch in ath10k_wmi_attach().
kvalo: improve the commit log
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the appropriate define instead of 6.
Signed-off-by: Joe Perches <joe@perches.com>
Noticed-by: Julia Lawall <julia.lawall@lip6.fr> via spatch script
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware IE containers can dynamically provide various information what
firmware supports. Also it can embed more than one image so updating firmware
is easy, user just needs to update one file in /lib/firmware/.
The firmware API 2 or higher will use the IE container format, the current API
1 will not use the new format but it still is supported for some time. FW API 2
files are named as firmware-2.bin (which contains both firmware and otp images)
and API 1 files are firmware.bin and otp.bin.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The wmi_start_scan_cmd has an extra filed in our main
firmware track, reflact that to not have a mismatch in
case of 10.x track.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is done exactly the same way as for vdev.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Both firmwares (main and 10.x) have different set of vdev
parameters. To stay in sync with FW API, this patch introduces
a dynamic registering method.
ath10k_wmi_vdev_set_param() takes now indirect u32 value
to identify the Vdev parameter it want's to set.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce all TARGET specific values for 10.x firmware.
Some of them are common for both firmwares we will support,
but to avoid confusion, define everything with prefix 10X_.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to API differences in initialization structures for
main and 10.x firmwares we need to split the wmi_init_cmd
and wmi_resource_config structures.
This will be usefull also when setting the correct TARGET values,
like: number of peers, vdevs, pdevs etc.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is still the only way to submit mgmt frames in case
of 10.X firmware.
This patch introduces wmi_mgmt_tx queue, because of the
fact WMI command can block. This is a problem for
ath10k_tx_htt(), since it's called from atomic context.
The skb queue and worker are introduced to move the mgmt
frame handling out of .tx callback context and not block.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.X firmware can request a memory pool from host to offload
it's own resources. This is a feature designed especially
for AP mode where the target has to deal with large number
of peers.
So we allocate and map a consistent DMA memory which FW can
use to store e.g. peer rate contol maps.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Simon Wunderlich