On R-Car Gen2 and RZ/G1 platforms, we use the SBAR registers to make non
boot CPUs run a routine designed to bring up SMP and deal with hot plug.
The value contained in the SBAR registers is not initialized by a WDT
triggered reset, which means that after a WDT triggered reset we jump
to the SMP bring up routine, preventing the system from executing the
bootrom code.
The purpose of this patch is to jump to the bootrom code in case of a
WDT triggered reset, and keep the SMP functionality untouched.
In order to tell if the code had been called due to the WDT overflowing
we are testing WOVF from register RWTCSRA.
The new function shmobile_boot_vector_gen2 isn't replacing
shmobile_boot_vector for backward compatibility reasons. The kernel
will install the best option (either shmobile_boot_vector or
shmobile_boot_vector_gen2) to ICRAM1 after parsing the device tree,
according to the amount of memory available.
Since shmobile_boot_vector has become bigger, "reg" property of nodes
compatible with "renesas,smp-sram" now need to be set to a value
greater or equal to "<0 0x60>".
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: dropped #ifdef from common.h]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Cortex-A7, the arch timer CNTVOFF register is uninitialized.
Ideally it should be initialized by the boot loader, but it isn't.
For the boot CPU, CNTVOFF is initialized by Linux since commit
9ce3fa6816 ("ARM: shmobile: rcar-gen2: Add CA7 arch_timer
initialization for r8a7794").
For secondary CPU cores, no such initialization is done.
Hence when enabling SMP on r8a7794, the kernel log is spammed with:
WARNING: Underflow in clocksource 'arch_sys_counter' observed, time update ignored.
Please report this, consider using a different clocksource, if possible.
Your kernel is probably still fine.
As Marc Zyngier pointed out that Cortex-A15 and Cortex-A7 are similar with
respect to CNTVOFF, we have been very lucky this just worked on R-Car
Gen2 SoCs with Cortex-A15 cores.
To fix this:
- Move the existing inline asm code to initialize CNTVOFF to an
assembler source file (adding comments and replacing hardcoded
constants by definitions in the process), so it can be reused,
- Perform the initialization of CNTVOFF on the boot CPU (Cortex-A15 or
Cortex-A7) on all R-Car Gen2 and RZ/G1 parts,
- Wrap the standard secondary_startup() routine inside a routine which
initializes CNTVOFF.
Based on patches by Hisashi Nakamura in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a function to check if other DT based method is available, and
if so return false to not hook up smp_ops from the machine vector.
This results in that DT-based SMP support has priority over older
C-based smp_ops code, and in case DT-based SMP support code does not
exist in the DTB then the old smp_ops code will still work as-is.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the SCU registers are mapped in SoC-specific code, using
different methods, all involving the static mapping set up from
machine_desc.map_io():
- On emev2, a static (non-identity) mapping is used, with ioremap().
As the static mapping uses the MT_DEVICE type, ioremap() reuses it,
and the returned virtual address is suitable for passing to
shmobile_smp_hook(),
- On sh73a0 and r8a7779, a static identity mapping is used, with the
legacy IOMEM() macro.
As the static mapping uses the MT_DEVICE_NONSHARED type, replacing
IOMEM() by ioremap() would create a new mapping, whose virtual
address cannot be passed to shmobile_smp_hook().
Move the mapping of the SCU registers from SoC-specific code to common
code, always using ioremap(). To work in the absence of a static
mapping, this requires passing the physical SCU base address to
shmobile_smp_hook().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
CPU boot configuration writes to shmobile_boot_arg, which is located in
the .text section, and thus should not be written to.
As of commit 1d33a354bb ("ARM: shmobile: Per-CPU SMP boot / sleep
code for SCU SoCs"), and ignoring accidental remainings,
shmobile_boot_arg is always set to MPIDR_HWID_BITMASK by C code.
Hence we can just hardcode this in the assembler code, and remove the
variable, and thus also remove the need to write to this variable.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The shmobile_clk_init() function has been removed and the linux/sh_clk.h
header doesn't need to be included anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The last user of twd_local_timer was removed in commit c99cd90d98
("ARM: shmobile: r8a7779: Remove legacy SoC code").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The last caller of shmobile_earlytimer_init() was removed in commit
c99cd90d98 ("ARM: shmobile: r8a7779: Remove legacy SoC code").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The last caller of shmobile_setup_console() was removed in commit
44d88c754e ("ARM: shmobile: Remove legacy SoC code for R-Mobile
A1").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Writes to /sys/.../cpuX/online fail if we determine the platform
doesn't support hotplug for that CPU. Furthermore, if the cpu_die
op isn't specified the system hangs when we try to offline a CPU
and it comes right back online unexpectedly. Let's figure this
stuff out before we make the sysfs nodes so that the online file
doesn't even exist if it isn't (at least sometimes) possible to
hotplug the CPU.
Add a new 'cpu_can_disable' op and repoint all 'cpu_disable'
implementations at it because all implementers use the op to
indicate if a CPU can be hotplugged or not in a static fashion.
With PSCI we may need to add a 'cpu_disable' op so that the
secure OS can be migrated off the CPU we're trying to hotplug.
In this case, the 'cpu_can_disable' op will indicate that all
CPUs are hotpluggable by returning true, but the 'cpu_disable' op
will make a PSCI migration call and occasionally fail, denying
the hotplug of a CPU. This shouldn't be any worse than x86 where
we may indicate that all CPUs are hotpluggable but occasionally
we can't offline a CPU due to check_irq_vectors_for_cpu_disable()
failing to find a CPU to move vectors to.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Dave Martin <Dave.Martin@arm.com>
Acked-by: Simon Horman <horms@verge.net.au> [shmobile portion]
Tested-by: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: <linux-sh@vger.kernel.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All ARMv5 and older CPUs invalidate their caches in the early assembly
setup function, prior to enabling the MMU. This is because the L1
cache should not contain any data relevant to the execution of the
kernel at this point; all data should have been flushed out to memory.
This requirement should also be true for ARMv6 and ARMv7 CPUs - indeed,
these typically do not search their caches when caching is disabled (as
it needs to be when the MMU is disabled) so this change should be safe.
ARMv7 allows there to be CPUs which search their caches while caching is
disabled, and it's permitted that the cache is uninitialised at boot;
for these, the architecture reference manual requires that an
implementation specific code sequence is used immediately after reset
to ensure that the cache is placed into a sane state. Such
functionality is definitely outside the remit of the Linux kernel, and
must be done by the SoC's firmware before _any_ CPU gets to the Linux
kernel.
Changing the data cache clean+invalidate to a mere invalidate allows us
to get rid of a lot of platform specific hacks around this issue for
their secondary CPU bringup paths - some of which were buggy.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This includes some
cleanups and removal of code, and the final flip of config dependencies
- Shmobile has several platforms that are going multiplatform, but this
branch also contains a bunch of cleanups that they weren't able to keep
separate in a good way. THere's also a removal of one of their SoCs and the
corresponding boards (sh7372 and mackerel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNzfJAAoJEIwa5zzehBx3iRcP/1v9Rw2yk4NpUDaz5EUwhwN6
y5l29gW8jJmVuHWqLUqsgh61dsj5AEEAL7fEEbR8e8848s+RxsehjsGPIxFOkR74
KaKSRlrUgxKcsFN97Jo/WqT3seC83hg6zWQapwNypX33gBtrRLPhM9FEb05asYA8
6x7N29kFeH9M3A6lrabXGWz5tPRZSthwuBSmomHOfgqa5zbgkoaK59j867Yac0q+
Pemh0eJZHC3Pyrmh7ZcVaCaSvr1QO6ructmLopmHAXfls2Fi21wq3IN3641aiitC
G7hhb1/c961MpE3p+0dQyrXs645qIgYv/fDxp72T8YwA7FhjMmIscX/WiITXMlvC
Mg/fDJXqgRkTPWjvVM6xF8TKCSdvqfmErWtHt2dtgvbFWL0ffSeoYF35AF5BODVG
jp8RR6vQ/CHKFao5iJmTpm0ccjnzdS82FEb0PrhG0vY+u6uCsKMim5tn8wUBuBkM
QU2FipNt6STC5ZcCSb+p7r5ihod9rG+BlNL/eXJ+pBHuVnjSgltEaZBP9qIiFjZl
MLRjm7JaEY3LpAR/TVurtSrUnh0zC0RRSzptK4RekmFIwyL+mqq/I1yrksdnVjgf
upj1dZwFRsVtD5PcaU3LyTYCOLSI8L9+b6vVvfFH0Sq4V7TkaBkI/kxnhI2WfkBc
CJ+3vptpyphw6zHAngAN
=Vq4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code changes from Olof Johansson:
"The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This
includes some cleanups and removal of code, and the final flip of
config dependencies
- Shmobile has several platforms that are going multiplatform, but
this branch also contains a bunch of cleanups that they weren't
able to keep separate in a good way. THere's also a removal of one
of their SoCs and the corresponding boards (sh7372 and mackerel)"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: at91/pm: move AT91_MEMCTRL_* to pm.h
ARM: at91/pm: move the standby functions to pm.c
ARM: at91: fix pm_suspend.S compilation when ARMv6 is selected
ARM: at91: add a Kconfig dependency on multi-platform
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: shmobile: r8a7778: enable multiplatform target
ARM: shmobile: bockw: add sound to DT
ARM: shmobile: r8a7778: add sound to DT
ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
DT: i2c: add trivial binding for OKI ML86V7667 video decoder
ARM: shmobile: r8a7778: common clock framework CPG driver
ARM: shmobile: bockw dts: set extal clock frequency
ARM: shmobile: bockw dts: Move Ethernet node to BSC
ARM: shmobile: r8a73a4: Remove legacy code
...
The default idle driver uses one state with the WFI instruction.
The default idle routine invokes WFI when no cpuidle driver is present.
The default cpuidle driver is pointless and does not give more than the
default idle routine and moreover it pulls all the mathematics tied with
the cpuidle governor for nothing, hence consuming more energy.
Remove the default driver, the related code and register the driver directly.
[compiled only - no board - no test]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove support for the legacy Cortex-A8 based sh7372 SoC.
The Linux kernel still lacks DT bindings for the sh7372 INTC
interrupt controller so DT multiplatform support is not possibile.
Also, the sh7372 SoC never went into mass production anyway so to
aid migration to DT multiplatform simply get rid of sh7372 support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
APMU resources are not common to all R-Car SoCs so don't share this data.
A subsequent patch will correct the CPU cores for the r8a7791.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
All ARM mach-shmobile SoCs and boards now rely on DTS for
CPU Frequency information, so remove the unused function
shmobile_setup_delay(). While at it, make the function
shmobile_setup_delay_hz() static.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Use shmobile_init_late on r8a7791 and r8a7790 whien booting using DT-only
* Support Core-Standby for Suspend to RAM on r8a7791 and r8a7790 SoCs
* Shared CMA reservation for R-Car Gen2 SoCs
* Add r8a7791 SYSC power management support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6J6K
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Updates for v3.17" from Simon Horman:
- Use shmobile_init_late on r8a7791 and r8a7790 whien booting using DT-only
- Support Core-Standby for Suspend to RAM on r8a7791 and r8a7790 SoCs
- Shared CMA reservation for R-Car Gen2 SoCs
- Add r8a7791 SYSC power management support
* tag 'renesas-soc-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove ARCH_HAS_CPUFREQ config for shmobile
ARM: shmobile: rcar-gen2: update call to dma_contiguous_reserve_area
ARM: shmobile: rcar-gen2: correct return value of shmobile_smp_apmu_suspend_init
ARM: shmobile: rcar-gen2: Remove useless copied section for LongTrail
ARM: shmobile: rcar-gen2: Use "1ULL" instead of "(u64)1"
ARM: shmobile: rcar-gen2: Update for of_get_flat_dt_prop() update
ARM: shmobile: Add shared R-Car Gen2 CMA reservation code
ARM: shmobile: Use shmobile_init_late() on r8a7791 DT-only
ARM: shmobile: Use shmobile_init_late() on r8a7790 DT-only
ARM: shmobile: Mark all SoCs in shmobile as CPUFreq, capable
ARM: shmobile: r8a7791: Support Core-Standby for Suspend to RAM
ARM: shmobile: r8a7790: Support Core-Standby for Suspend to RAM
ARM: shmobile: APMU: Add Core-Standby-state for Suspend to RAM
ARM: shmobile: r8a7791 SYSC setup code
Signed-off-by: Olof Johansson <olof@lixom.net>
Move r8a7779 SoC and its Marzen board to use common clocks,
multiplatform and initialise SCIF (serial) devices using DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2zqe
-----END PGP SIGNATURE-----
Merge tag 'renesas-r8a7779-multiplatform-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM Based SoC r8a7779-multiplatform Updates for v3.17" from
Simon Horman:
Move r8a7779 SoC and its Marzen board to use common clocks,
multiplatform and initialise SCIF (serial) devices using DT.
* tag 'renesas-r8a7779-multiplatform-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
ARM: shmobile: marzen: Do not use workaround for scif devices
ARM: shmobile: marzen: Initialise SCIF devices using DT
ARM: shmobile: marzen: Remove early_printk from command line
ARM: shmobile: r8a7779: Add scif nodes to dtsi
ARM: shmobile: r8a7779 dtsi: Correct #address-cells/#size-cells for clocks
ARM: shmobile: r8a7779 dtsi: Update unit-addresses for clocks
ARM: shmobile: r8a7779: Remove unused r8a7779_init_delay()
ARM: shmobile: marzen-reference: Use DT CPU Frequency
ARM: shmobile: r8a7779: Use DT CPU Frequency in common case
ARM: shmobile: r8a7779: Add Maximum CPU Frequency to DTS
ARM: shmobile: marzen-reference: Remove legacy clock support
ARM: shmobile: Remove Marzen reference DTS
ARM: shmobile: Let Marzen multiplatform boot with Marzen DTB
ARM: shmobile: Remove non-multiplatform Marzen reference support
ARM: shmobile: marzen-reference: Instantiate clkdevs for SCIF and TMU
ARM: shmobile: marzen-reference: Initialize CPG device
ARM: shmobile: r8a7779: Initial multiplatform support
ARM: shmobile: marzen-reference: Move clock and OF device initialisation into board code
ARM: shmobile: r8a7779: Move r8a7779_earlytimer_init to clock-r8a7779.c
ARM: shmobile: r8a7779: Add helper to read mode pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The dummy shmobile_smp_apmu_suspend_init() function provided when
CPU_IDLE is not set should not return a value as per the signature
of the function.
This problem appears to have been introduced by
867ba81f728f1daa ("ARM: shmobile: APMU: Add Core-Standby-state for Suspend
to RAM").
Cc: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch add Core-Standby-state for Suspend to RAM.
Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
[horms+renesas@verge.net.au: rebase]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location for common.h so it can be used as #include "common.h"
instead of the old style #include <mach/common.h>.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fabrizio Castro