* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix memory_block_size_bytes() for non-pseries
mm: Move definition of MIN_MEMORY_BLOCK_SIZE to a header
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915/ringbuffer: Idling requires waiting for the ring to be empty
Revert "drm/i915: enable rc6 by default"
drm/i915: Clean up i915_driver_load failure path
drm/i915: Enable GPU reset on Ivybridge.
drm/i915/dp: manage sink power state if possible
drm/i915/dp: consolidate AUX retry code
drm/i915/dp: remove DPMS mode tracking from DP
drm/i915/dp: try to read receiver capabilities 3 times when detecting
drm/i915/dp: read more receiver capability bits on hotplug
drm/i915/dp: use DP DPCD defines when looking at DPCD values
drm/i915/dp: retry link status read 3 times on failure
...which is measured by the size and not the amount of space remaining.
Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:
[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
This reverts commit a51f7a66fb.
We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: Keith Packard <keithp@keithp.com>
i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.
i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.
i915_driver_load also has some incorrect gotos in the error cleanup
paths:
* After failing to initialize the GTT (which cannot happen, btw,
intel_gtt_get returns a fixed (non-NULL) value), it tries to
free the uninitialized WC IO mapping. Fixed this by changing the
target from out_iomapfree to out_rmmap
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Lin Ming <ming.m.lin@intel.com>
The macro MIN_MEMORY_BLOCK_SIZE is currently defined twice in two .c
files, and I need it in a third one to fix a powerpc bug, so let's
first move it into a header
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] msp3400: fill in v4l2_tuner based on vt->type field
[media] tuner-core.c: don't change type field in g_tuner or g_frequency
[media] cx18/ivtv: fix g_tuner support
[media] tuner-core: power up tuner when called with s_power(1)
[media] v4l2-ioctl.c: check for valid tuner type in S_HW_FREQ_SEEK
[media] tuner-core: simplify the standard fixup
[media] tuner-core/v4l2-subdev: document that the type field has to be filled in
[media] v4l2-subdev.h: remove unused s_mode tuner op
[media] feature-removal-schedule: change in how radio device nodes are handled
[media] bttv: fix s_tuner for radio
[media] pvrusb2: fix g/s_tuner support
[media] v4l2-ioctl.c: prefill tuner type for g_frequency and g/s_tuner
[media] tuner-core: fix tuner_resume: use t->mode instead of t->type
[media] tuner-core: fix s_std and s_tuner
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
hp-wmi: fix use after free
dell-laptop - using buffer without mutex_lock
Revert: "dell-laptop: Toggle the unsupported hardware killswitch"
platform-drivers-x86: set backlight type to BACKLIGHT_PLATFORM
thinkpad-acpi: handle HKEY 0x4010, 0x4011 events
drivers/platform/x86: Fix memory leak
thinkpad-acpi: handle some new HKEY 0x60xx events
acer-wmi: fix bitwise bug when set device state
acer-wmi: Only update rfkill status for associated hotkey events
[ 191.310008] WARNING: kmemcheck: Caught 32-bit read from freed memory (f0d25f14)
[ 191.310011] c056d2f088000000105fd2f00000000050415353040000000000000000000000
[ 191.310020] i i i i f f f f f f f f f f f f f f f f f f f f f f f f f f f f
[ 191.310027] ^
[ 191.310029]
[ 191.310032] Pid: 737, comm: modprobe Not tainted 3.0.0-rc5+ #268 Hewlett-Packard HP Compaq 6005 Pro SFF PC/3047h
[ 191.310036] EIP: 0060:[<f80b3104>] EFLAGS: 00010286 CPU: 0
[ 191.310039] EIP is at hp_wmi_perform_query+0x104/0x150 [hp_wmi]
[ 191.310041] EAX: f0d25601 EBX: f0d25f00 ECX: 000121cf EDX: 000121ce
[ 191.310043] ESI: f0d25f10 EDI: f0f97ea8 EBP: f0f97ec4 ESP: c173f34c
[ 191.310045] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 191.310046] CR0: 8005003b CR2: f540c000 CR3: 30f30000 CR4: 000006d0
[ 191.310048] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 191.310050] DR6: ffff4ff0 DR7: 00000400
[ 191.310051] [<f80b317b>] hp_wmi_dock_state+0x2b/0x40 [hp_wmi]
[ 191.310054] [<f80b6093>] hp_wmi_init+0x93/0x1a8 [hp_wmi]
[ 191.310057] [<c10011f0>] do_one_initcall+0x30/0x170
[ 191.310061] [<c107ab9f>] sys_init_module+0xef/0x1a60
[ 191.310064] [<c149f998>] sysenter_do_call+0x12/0x28
[ 191.310067] [<ffffffff>] 0xffffffff
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This reverts commit a3d77411e8,
as it causes a mess in the wireless rfkill status on some models.
It is probably a bad idea to toggle the rfkill for all dell models
without the respect to the claim that it is hardware-controlled.
Cc: stable@kernel.org
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Patch 2e711c04db
(PM: Remove sysdev suspend, resume and shutdown operations)
deleted sysdev_suspend(), which was being relied on to call
check_wakeup_irqs() in suspend. If check_wakeup_irqs() is not
called, wake interrupts that are pending when suspend is
entered may be lost. It also breaks IRQCHIP_MASK_ON_SUSPEND,
which is handled in check_wakeup_irqs().
This patch adds a call to check_wakeup_irqs() in syscore_suspend(),
similar to what was deleted in sysdev_suspend().
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
I came across a memory leak during a cyclic cpu-online-offline test.
Signed-off-by: Yu Luming <luming.yu@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (pmbus) Improve auto-detection of temperature status register
hwmon: (lm95241) Fix negative temperature results
hwmon: (lm95241) Fix chip detection code
It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+
Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.
Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6994/1: smp_twd: Fix typo in 'twd_timer_rate' printing
ARM: 6987/1: l2x0: fix disabling function to avoid deadlock
ARM: 6966/1: ep93xx: fix inverted RTS/DTR signals on uart1
ARM: 6980/1: mmci: use StartBitErr to detect bad connections
ARM: 6979/1: mach-vt8500: add forgotten irq_data conversion
ARM: move memory layout sanity checking before meminfo initialization
ARM: 6990/1: MAINTAINERS: add entry for ARM PMU profiling and debugging
ARM: 6989/1: perf: do not start the PMU when no events are present
ARM: dmabounce: fix map_single() error return value
When firewire-ohci is bound to a Pinnacle MovieBoard, eventually a
"Register access failure" is logged and an interrupt storm or a kernel
panic happens. https://bugzilla.kernel.org/show_bug.cgi?id=36622
Until this is sorted out (if that is going to succeed at all), let's
just prevent firewire-ohci from touching these devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C2440: fix section mismatch on mini2440
ARM: S3C24XX: drop return codes in void function of dma.c
ARM: S3C24XX: don't use uninitialized variable in dma.c
ARM: EXYNOS4: Set appropriate I2C device variant
ARM: S5PC100: Fix for compilation error
spi/s3c64xx: Bug fix for SPI with different FIFO level
ARM: SAMSUNG: Add tx_st_done variable
ARM: EXYNOS4: Address a section mismatch w/ suspend issue.
ARM: S5P: Fix bug on init of PWMTimers for HRTimer
ARM: SAMSUNG: header file revised to prevent declaring duplicated
ARM: EXYNOS4: fix improper gpio configuration
ARM: EXYNOS4: Fix card detection for sdhci 0 and 2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: max8997: Fix setting inappropriate value for ramp_delay variable
regulator: db8500-prcmu: small fixes
regulator: max8997: remove dependency on platform_data pointer
regulator: MAX8997: Fix for divide by zero error
regulator: max8952 - fix wrong gpio valid check
This driver handles the variants pca9530-pca9533, so it chose the name
"pca953x". However, there is a gpio driver which decided on the same
name. As a result, those two can't be loaded at the same time. Add a
subsystem prefix to make the driver name unique. Device matching will not
suffer, because both are I2C drivers which match using a
i2c_device_id-table which is not altered.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:
: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.
This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves. Unfortunately,
this is not always the case. The sleep is restored but as a parameter to
the probe function in the pdata.
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LM95241 driver accepts every chip ID equal to or larger than 0xA4 as its
own, and other chips such as LM95245 use chip IDs in the accepted ID range.
This results in false chip detection.
Fix problem by accepting only the known LM95241 chip ID.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ramp_delay variable can be set lower than the desired value.
This patch fixes it.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Small cleanups for better readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The platform_data (pdata) may be pointing to __initdata section, which
may be free'd from the memory. The dependency on pdata in non-init
functions is removed in this patch to allow platform to declare
__initdata for platform data.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently, ramp_delay variable is used uninitialzed in
max8997_set_voltage_ldobuck which gets called through
regulator_register calls.
To fix the problem, in max8997_pmic_probe, ramp_delay initialization
code is moved before calls to regulator_register.
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
evergreen+ asics have 2-6 crtcs. Don't access crtc registers
for crtc regs that don't exist as they have very high latency
and may cause problems on some asics. The previous code missed
a few cases and was not fine grained enough (missed the 4 crtc
case for example).
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=38800
v2: fix typo noticed by Chris Bandy <cbandy@jbandy.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/kms: allow drm_mode_group with no objects
drm/radeon/kms: free ib pool on module unloading
drm/radeon/kms: fix typo in evergreen disp int status register
drm/radeon/kms: fix typo in IH_CNTL swap bitfield
The wrong bit was masked when acking langwell gpio interrupts.
Reason for maskig the wrong bit was probably because__ffs() and ffs() functions
return bit indexes differently (0..31 vs 1..32)
This fixes langwell based devices from hanging when a gpio interrupt is
triggered and undoes the breakage which occurred in change set
732063b92b
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-30-rc5/all-i2c' of git://git.fluff.org/bjdooks/linux:
i2c-bfin-twi: abort transfer is MEM bit is reset unexpectedly
i2c-s3c2410: Remove useless break code
i2c-s3c2410: Fix typo 'i2s' -> 'i2c'
i2c: tegra: Assign unused slave address
According to the hardware documentation, GDRST is exactly the same as on
Sandybridge. So simply enable the existing code.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
On sinks with a DPCD rev of 1.1 or greater, we can send sink power
management commands to address 0x600 per section 5.1.5 of the
DisplayPort 1.1a spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
When checking link status during a hot plug event or detecting sink
presence, we need to retry 3 times per the spec (section 9.1 of the 1.1a
DisplayPort spec). Consolidate the retry code into a
native_aux_read_retry function for use by get_link_status and _detect.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
We currently use this when a hot plug event is received, only checking
the link status and re-training if we had previously configured a link.
However if we want to preserve the DP configuration across both hot plug
and DPMS events (which we do for userspace apps that don't respond to
hot plug uevents), we need to unconditionally check the link and try to
bring it up on hot plug.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
If ->detect is called too soon after a hot plug event, the sink may not
be ready yet. So try up to 3 times with 1ms sleeps in between tries to
get the data (spec dictates that receivers must be ready to respond within
1ms and that sources should try 3 times).
See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
When a hotplug event is received, we need to check the receiver cap bits
in case they've changed (as they might with a hub or chain config).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Makes it easier to search for DP related constants.
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Linus Torvalds