For performance reasons we want to avoid updating the tail pointer in
the driver tx ring as much as possible. To accomplish this we add
batching support to the redirect path in XDP.
This adds another ndo op "xdp_flush" that is used to inform the driver
that it should bump the tail pointer on the TX ring.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a trace event for xdp redirect which may help when debugging
XDP programs that use redirect bpf commands.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are optimizations we can add after the basic feature is
enabled. But, for now keep the patch simple.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_rings and rx_rings are cleaned up on close paths in ixgbe driver
however, xdp_rings are not. Set the xdp_rings to NULL here so that
we can use the pointer to indicate if the XDP rings are initialized.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now IPv6 unregistered multicast traffic would be flooded like
broadcast, even when MLD snooping was enabled on the bridge. This was
intentional as MLD packet traps were missing, preventing the bridge
driver from programming MDB entries to the device.
Previous patch added these traps, so we can now finally flood IPv6
unregistered multicast packets to specific ports via the multicast table
instead of flooding them to all ports via the broadcast table.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for IPv6 MLDv1/2 packet trapping.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case local sockets have the IP_ROUTER_ALERT socket option set, then
they expect to get packets with the Router Alert option.
Trap such packets, so that the kernel could inspect them and potentially
send them to interested sockets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1c6c6d221e ("mlxsw: spectrum: Mirror certain packets to
CPU") we marked packets that were mirrored to the CPU, so that they
won't be flooded again by the bridge driver.
However, certain packets are trapped in the device's router block, after
passing through the bridge block where they were potentially flooded.
Mark all packets coming from L3 traps, so that they won't be potentially
flooded again by the bridge driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support offloading rules that match on ip tos.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ecn and dscp fields to the ipv4 acl block.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define new element for ip tos (ecn, dscp) and place it into scratch area.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support offloading rules that match on ip ttl.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ttl field to the ipv4 acl block.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define new element for ip ttl and place it into scratch area.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep supporting proprietary "xlnx,phy-type" attribute and add support for
MII connectivity to the PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code didn't handle non-IPv4 packets very well, so the
offload advertising had to be scaled back down to just IP. Here we
add the bits needed to support TCP and UDP packets over IPv6 and
turn the offload advertising back on.
Orabug: 26289579
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since internal phy-mode is reserved for non-xMII protocol we cannot use
it with dwmac-sun8i.
Furthermore, all DT patchs which comes with this patch were cleaned, so
the current state is broken.
This reverts commit 1c2fa5f846 ("net: stmmac: support future possible different internal phy mode")
Fixes: 1c2fa5f846 ("net: stmmac: support future possible different internal phy mode")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have more than 32 unicast MAC addresses assigned to an interface
we will read beyond the end of the address table in the driver when
adding filters. The next 256 entries store multicast addresses, so we
will end up attempting to insert duplicate filters, which is mostly
harmless. If we add more than 288 unicast addresses we will then read
past the multicast address table, which is likely to be more exciting.
Fixes: 12fb0da45c ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no check for return code of smsc911x_drv_probe()
in smsc911x_drv_probe(). The patch adds one.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lower level nl80211 code in cfg80211 ensures that "len" is between
25 and NL80211_ATTR_FRAME (2304). We subtract DOT11_MGMT_HDR_LEN (24) from
"len" so thats's max of 2280. However, the action_frame->data[] buffer is
only BRCMF_FIL_ACTION_FRAME_SIZE (1800) bytes long so this memcpy() can
overflow.
memcpy(action_frame->data, &buf[DOT11_MGMT_HDR_LEN],
le16_to_cpu(action_frame->len));
Cc: stable@vger.kernel.org # 3.9.x
Fixes: 18e2f61db3 ("brcmfmac: P2P action frame tx.")
Reported-by: "freenerguo(郭大兴)" <freenerguo@tencent.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns port type is not debug mode, netif_tx_disable is called
when there is a tx timeout, which requires system reboot to return
to normal state. This patch fix this problem by resetting the net
dev.
Fixes: b5996f11ea ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally free a NULL pointer and leak the pointer we want to
free. Also you can tell from the label name what was intended. :)
Fixes: abfcdc1de9 ("nfp: add a stats handler for flower offloads")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't rely on kzalloc() always succeeding, so check its return value.
Suppresses the following smatch error:
mlxsw_sp_switchdev_event() error: potential null dereference
'switchdev_work->fdb_info.addr'. (kzalloc returns
null)
Fixes: af06137892 ("mlxsw: spectrum_switchdev: Add support for learning FDB through notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 10e23eb299 ("mlxsw: spectrum: Remove support for bypass bridge
port attributes/vlan set") removed statements that used 'bridge_vlan',
but didn't remove the variable itself resulting in the following warning
with W=1:
warning: variable ‘bridge_vlan’ set but not used
[-Wunused-but-set-variable]
Remove the variable and suppress the warning.
Fixes: 10e23eb299 ("mlxsw: spectrum: Remove support for bypass bridge port attributes/vlan set")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on IPv6 route replace I realized we can have a
use-after-free in IPv4 in case the replaced route is offloaded and the
only one using its FIB info.
The problem is that fib_table_insert() drops the reference on the FIB
info of the replaced routes which is eventually freed via call_rcu().
Since the driver doesn't hold a reference on this FIB info it can cause
a use-after-free when it tries to clear the RTNH_F_OFFLOAD flag stored
in fi->fib_flags.
After running the following commands in a loop for enough time with a
KASAN enabled kernel I finally got the below trace.
$ ip route add 192.168.50.0/24 via 192.168.200.1 dev enp3s0np3
$ ip route replace 192.168.50.0/24 dev enp3s0np5
$ ip route del 192.168.50.0/24 dev enp3s0np5
BUG: KASAN: use-after-free in mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
Read of size 4 at addr ffff8803717d9820 by task kworker/u4:2/55
[...]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
? mlxsw_sp_router_neighs_update_work+0x1cd0/0x1ce0 [mlxsw_spectrum]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
__asan_load4+0x61/0x80
mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
mlxsw_sp_fib_entry_offload_refresh+0xb6/0x370 [mlxsw_spectrum]
mlxsw_sp_router_fib_event_work+0xd1c/0x2780 [mlxsw_spectrum]
[...]
Freed by task 5131:
save_stack_trace+0x16/0x20
save_stack+0x46/0xd0
kasan_slab_free+0x70/0xc0
kfree+0x144/0x570
free_fib_info_rcu+0x2e7/0x410
rcu_process_callbacks+0x4f8/0xe30
__do_softirq+0x1d3/0x9e2
Fix this by taking a reference on the FIB info when creating the nexthop
group it represents and drop it when the group is destroyed.
Fixes: 599cf8f95f ("mlxsw: spectrum_router: Add support for route replace")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the error path of mlxsw_sp_nexthop_init() is symmetric
with mlxsw_sp_nexthop_fini(). Noticed during code review.
Fixes: a8c9701427 ("mlxsw: spectrum_router: Refactor nexthop init routine")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not allowed to block on the RCU reader side, so can't
just hold the mutex as before. As a quick fix, convert it to
a spinlock.
Fixes: d9f1f61c08 ("tap: Extending tap device create/destroy APIs")
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the introduction of ULD (Upper-Layer Drivers), the MSI-X
deallocating path changed in cxgb4: the driver frees the interrupts
of ULD when unregistering it or on shutdown PCI handler.
Problem is that if a MSI-X is not freed before deallocated in the PCI
layer, it will trigger a BUG() due to still "alive" interrupt being
tentatively quiesced.
The below trace was observed when doing a simple unbind of Chelsio's
adapter PCI function, like:
"echo 001e:80:00.4 > /sys/bus/pci/drivers/cxgb4/unbind"
Trace:
kernel BUG at drivers/pci/msi.c:352!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c0000000005a5e60] free_msi_irqs+0xa0/0x250
LR [c0000000005a5e50] free_msi_irqs+0x90/0x250
Call Trace:
[c0000000005a5e50] free_msi_irqs+0x90/0x250 (unreliable)
[c0000000005a72c4] pci_disable_msix+0x124/0x180
[d000000011e06708] disable_msi+0x88/0xb0 [cxgb4]
[d000000011e06948] free_some_resources+0xa8/0x160 [cxgb4]
[d000000011e06d60] remove_one+0x170/0x3c0 [cxgb4]
[c00000000058a910] pci_device_remove+0x70/0x110
[c00000000064ef04] device_release_driver_internal+0x1f4/0x2c0
...
This patch fixes the issue by refactoring the shutdown path of ULD on
cxgb4 driver, by properly freeing and disabling interrupts on PCI
remove handler too.
Fixes: 0fbc81b3ad ("Allocate resources dynamically for all cxgb4 ULD's")
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option "h" (host order ) exists for ipv4 only.
Remove the h when printing ipv6 addresses.
Lead to the following smatch warning:
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:585 qed_iwarp_print_tcp_ramrod()
warn: '%pI6' can only be followed by c
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1521 qed_iwarp_print_cm_info()
warn: '%pI6' can only be followed by c
Fixes commit 456a584947 ("qed: iWARP CM add passive side connect")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'alloc_dma_[rt]x_desc_resources()' functions look very close.
Remove a useless initialization and use the same label name for error
handling path in order to get them even closer.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the first 'kmalloc_array' within the loop fails, we should free what
as already been allocated, as done in all other error handling path.
Fixes: ce736788e8 ("net: stmmac: adding multiple buffers for TX")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the first 'kmalloc_array' within the loop fails, we should free what
as already been allocated, as done in all other error handling path.
Fixes: 54139cf3bb ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if 'ioread32()' returns 0xFFFFFFF, we have to go through the error
handling path as done everywhere else in this function.
Move the 'err_free_wq' label to better match its name and its location
and add a new label 'err_disable_wq'.
Update the code accordingly.
Fixes: 373fb0873d ("enic: add devcmd2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF driver sets up a list of firmware commands from the VF driver that
needs to be forwarded to the PF for approval. This list is a 256-bit
bitmap. The code that sets up the bitmap falls apart on big-endian
architecture. __set_bit() does not work because it operates on long types
whereas the firmware interface is defined in u32 types, causing bits in
the wrong 32-bit word to be set.
Fix it by setting the proper bits on an array of u32.
Fixes: de68f5de56 ("bnxt_en: Fix bitmap declaration to work on 32-bit arches.")
Reported-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing channels from combined to rx/tx or vice versa, the code
uses the wrong "sh" parameter to determine if we are reserving rings
for shared or non-shared mode. It should be using the ethtool requested
"sh" parameter instead of the current "sh" parameter.
Fix it by passing the "sh" parameter to bnxt_reserve_rings(). For
ethtool, we will pass in the requested "sh" parameter.
Fixes: 391be5c273 ("bnxt_en: Implement new scheme to reserve tx rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
.ndo_get_stats64() may not be protected by RTNL and can race with
.ndo_stop() or other ethtool operations that can free the statistics
memory. Fix it by setting a new flag BNXT_STATE_READ_STATS and then
proceeding to read statistics memory only if the state is OPEN. The
close path that frees the memory clears the OPEN state and then waits
for the BNXT_STATE_READ_STATS to clear before proceeding to free the
statistics memory.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IPSec offload code introduced a build error:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_rxtx.o: In function `mlx5e_ipsec_build_inverse_table':
ipsec_rxtx.c:(.text+0x556): undefined reference
Another patch was added on top to fix the build error, but
that introduced a new bug, as we now use the remainder of
the division rather than the result.
This makes it use the correct helper function instead.
Fixes: 5dfd87b67c ("net/mlx5: IPSec, Fix 64-bit division on 32-bit builds")
Fixes: 2ac9cfe782 ("net/mlx5e: IPSec, Add Innova IPSec offload TX data path")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes fixes to mlx5 driver:
- Compilation warnings and issues introduced on v4.12
- Initialize CEE's getpermhwaddr address buffer to 0xff
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZYiE3AAoJEEg/ir3gV/o+/GYH/1qly/TNGUbmLyxFmx5dHBlI
1V98Rxrrk/Y2eA+PtcgHzJKcZ/vcAYhwAY/3JIY3qfiWyD/GAfK3hPcemMpNNyCj
va9C9SUEcGr6JEZ0UgGQDcmU3aWs1yslMe7+ZiW9k1EcG0HvEmaB2BPLRmVKxUWX
6gF0qdIGuj0wu7PL/ly5CZQ5jl8r6oKp665YJxvaJlVCaZYyZZgzuXK/MHuCZRbK
ziIONkmtGzfBb/Yocxgr2lSR+1PIFpDtRysBbhYJDlsMCPo3XMT+M+xJI92kH6ZP
pj8NxDvUTCHtyrmAk5aUxRzta71uqY6XgjR+PBwecG47jJ/+0kryxj1MU008diA=
=ebzr
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-07-09' of https://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2017-07-09
This series includes fixes to mlx5 driver:
- Compilation warnings and issues introduced on v4.12
- Initialize CEE's getpermhwaddr address buffer to 0xff
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Mostly fixing some light fallout from the changes that went into the
merge window.
1) Fix memory leaks on network namespace teardown in netfilter, from
Liping Zhang.
2) When comparing ipv6 nexthops, we have to take the lightweight
tunnel state into account as well. From David Ahern.
3) Fix socket option object length check in the new TLS code, from
Matthias Rosenfelder.
4) Fix memory leak in nfp driver flower support, from Jakub Kicinski.
5) Several netlink attribute validation fixes in cfg80211, from
Srinivas Dasari.
6) Fix context array leak in virtio_net, from Jason Wang.
7) SKB use after free in hns driver, from Yusheng Lin.
8) Fix socket leak on accept() in RDS, from Sowmini Varadhan. Also
add a WARN_ON() to sock_graft() so other protocol stacks don't
trip over this as well"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
net: ethernet: mediatek: remove useless code in mtk_probe()
mpls: fix uninitialized in_label var warning in mpls_getroute
doc: SKB_GSO_[IPIP|SIT] have been replaced
bonding: avoid NETDEV_CHANGEMTU event when unregistering slave
net/sock: add WARN_ON(parent->sk) in sock_graft()
rds: tcp: use sock_create_lite() to create the accept socket
net: hns: Fix a skb used after free bug
net: hns: Fix a wrong op phy C45 code
net: macb: Adding Support for Jumbo Frames up to 10240 Bytes in SAMA5D3
net: Update networking MAINTAINERS entry.
virtio-net: fix leaking of ctx array
cfg80211: Validate frequencies nested in NL80211_ATTR_SCAN_FREQUENCIES
cfg80211: Define nla_policy for NL80211_ATTR_LOCAL_MESH_POWER_MODE
cfg80211: Check if NAN service ID is of expected size
cfg80211: Check if PMKID attribute is of expected size
arcnet: com20020-pci: Fix an error handling path in 'com20020pci_probe()'
nfp: flower: add missing clean up call to avoid memory leaks
vrf: fix bug_on triggered by rx when destroying a vrf
ptp: dte: Use LL suffix for 64-bit constants
sctp: set the value of flowi6_oif to sk_bound_dev_if to make sctp_v6_get_dst to find the correct route entry.
...
Remove useless local variables _match_, _soc_ and the code related.
Notice that
const struct of_device_id of_mtk_match[] = {
{ .compatible = "mediatek,mt2701-eth" },
{},
};
So match->data is NULL.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Hongjun/Nicolas summarized in their original patch:
"
When a device changes from one netns to another, it's first unregistered,
then the netns reference is updated and the dev is registered in the new
netns. Thus, when a slave moves to another netns, it is first
unregistered. This triggers a NETDEV_UNREGISTER event which is caught by
the bonding driver. The driver calls bond_release(), which calls
dev_set_mtu() and thus triggers NETDEV_CHANGEMTU (the device is still in
the old netns).
"
This is a very special case, because the device is being unregistered
no one should still care about the NETDEV_CHANGEMTU event triggered
at this point, we can avoid broadcasting this event on this path,
and avoid touching inetdev_event()/addrconf_notify() path.
It requires to export __dev_set_mtu() to bonding driver.
Reported-by: Hongjun Li <hongjun.li@6wind.com>
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the user manual described, the second step to write to C45 phy
by mdio should be data, but not address. Here we should fix this
issue.
Fixes: 5b904d3940 ("net: add Hisilicon Network Subsystem MDIO support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per the SAMA5D3 device specification it supports Jumbo frames.
But the suggested flag and length of bytes it supports was not updated
in this driver config_structure.
The maximum jumbo frames the device supports :
10240 bytes as per the device spec.
While changing the MTU value greater than 1500, it threw error:
sudo ifconfig eth1 mtu 9000
SIOCSIFMTU: Invalid argument
Add this support to driver so that it works as expected and designed.
Signed-off-by: vishnuvardhan <vardhanraj4143@gmail.com>
[nicolas.ferre@microchip.com: modify slightly commit msg]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit d45b897b11 ("virtio_net: allow specifying context for rx")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this memory allocation fails, we should go through the error handling
path as done everywhere else in this function before returning.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller