This change is meant to make the code much more readable for MTQC and MRQC
configuration.
The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
DCB
En Dis
VMDq En VMDQ/DCB VMDq/RSS
Dis DCB/RSS RSS
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.
In this patch I basically did 3 things. I updated the logic for getting
the first register index. I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register. Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues. By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls. Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go. This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.
This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jett Kirsher says:
====================
This series contains updates to e1000e and ixgbe.
...
Alexander Duyck (5):
ixgbe: Simplify logic for getting traffic class from user priority
ixgbe: Cleanup unpacking code for DCB
ixgbe: Populate the prio_tc_map in ixgbe_setup_tc
ixgbe: Add function for obtaining FCoE TC based on FCoE user priority
ixgbe: Merge FCoE set_num and cache_ring calls into RSS/DCB config
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change merges the ixgbe_cache_ring_fcoe and ixgbe_set_fcoe_queues
logic into the DCB and RSS initialization calls.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In upcoming patches it will become increasingly common to need to determine
the FCoE traffic class in order to determine the correct queues for FCoE.
In order to make this easier I am adding a function for obtaining the FCoE
traffic class based on the user priority.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were cases where the prio_tc_map was not populated when we were
calling open. This will result in us incorrectly configuring the traffic
classes when DCB is enabled. In order to correct this I have updated the
code so that we now populate the values prior to allocating the q_vectors
and calling ixgbe_open.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is meant to be a generic clean-up of the remaining functions for
unpacking data from the DCB structures. The only real changes are:
replaced the variable i with tc for functions that were looping through the
traffic classes, and added a pointer for tc_class instead of path since
that way we only need to pull the pointer once instead of once per loop.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to help simplify the logic for getting traffic classes
from user priorities. To do this I am adding a function named
ixgbe_dcb_get_tc_from_up that will go through the traffic classes in
reverse order in order to determine which traffic class contains a bit for
a given user priority.
Adding a declaration for this new function to the header so that
we have a centralized means for sorting out traffic classes belonging to
features such as FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are really only 3 modes that can control the number of queues. Those
are RSS, DCB, and VMDq/SR-IOV. Currently we have things much more broken
up than they need to be for how we are configuring the rings. In order to
try and straiten some of this out I am going to start merging similar
functionality into single functions. To start with I am merging the Flow
Director ring configuration into the RSS ring configuration since Flow
Director cannot function with DCB or SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces a switch statement for an 82598 workaround with an if
statement that only applies to 82598. In addition I am pulling out several
dead pieces of code and instead of reading the SRRCTL register and then
modifying it we are just writing a value which we generate from scratch.
Finally I am also removing any drop enable related code since that was
moved to a function of its own.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The mask value for ring features was overloaded for FCoE which can lead to
some confusion. In order to avoid any confusion I am splitting the mask
value and adding an offset value. This can be used for the start of the
FCoE rings, and in the future I hope to use it to store the start of the
registers for SR-IOV.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are currently using indices to indicate the upper limit on a ring
feature. However since we can switch back and forth on features such as
DCB and that has effects on other features such as RSS it is preferable to
instead store the upper limit separate from the current value for the
number of rings related to the feature.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It makes much more sense for us to count q_vectors instead of MSI-X
vectors. We were using num_msix_vectors to find the number of q_vectors in
multiple places. This was wasteful since we only had one place that
actually needs the number of MSI-X vectors and that is in slow path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCB and SR-IOV cannot currently be enabled at the same time as the queueing
schemes are incompatible. If they are both enabled it will result in Tx
hangs since only the first Tx queue will be able to transmit any traffic.
This simple fix for this is to block us from enabling TCs in ixgbe_setup_tc
if SR-IOV is enabled. This change will be reverted once we can support
SR-IOV and DCB coexistence.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
FCoE target mode was experiencing issues due to the fact that we were
sending up data frames that were padded to 60 bytes after the DDP logic had
already stripped the frame down to 52 or 56 depending on the use of VLANs.
This was resulting in the FCoE DDP logic having issues since it thought the
frame still had data in it due to the padding.
To resolve this, adding code so that we do not pad FCoE frames prior to
handling them to the stack.
CC: <stable@vger.kernel.org>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for length <= 0 is bogus because length is unsigned, and network
stack never sends zero length packets (unless it is totally broken).
The check for really small packets can be optimized (using unlikely)
and calling skb_pad directly.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the method used for determining the link speed of
devices. The old method re-wrote some logic already existing in a mac.ops
function which should be used instead. The result is much simpler to
understand and removes a strange double-check of logic, as well as reducing
code redundancy.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 1G Fiber PHY modules (SFP+ modules). This support
comes along side support for 1G Copper PHY modules, but uses a different PHY
type (ixgbe_sfp_type_1g_sx_core).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a memory leak that was introduced in the 3.4 kernel. The
leak occurred when FCoE was enabled and traffic was passed over the FCoE
rings reserved for FCoE. The memory leak was due to us not populating the
compound page information on the order 1 pages needed for FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a potential hole when configuring the cycle counter used to
generate the nanosecond time clock. This clock is based off of the SYSTIME
registers along with the TIMINCA registers. The TIMINCA register determines
the increment to be added to the SYSTIME registers every DMA clock tick. This
register needs to be reconfigured whenever the link-speed changes. However,
the value calculated stays the same when link is down and when link is up.
Misconfiguration can occur if the link status changes due to a reset, which
causes the TIMINCA register to be reset. This reset puts the device in an
unstable state where the SYSTIME registers stop incrementing and the PTP
protocol does not function.
The solution is to double check the TIMINCA value and always reset the value
if the register is zero. This prevents a misconfiguration bug that halts the
PHC.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a potential Rx timestamp deadlock that causes the Rx
timestamping to stall indefinitely. The issue could occur when a PTP packet is
timestamped by hardware but never reaches the Rx queue. In order to prevent a
permanent loss of timestamping, the RXSTMP(L/H) registers have to be read to
unlock them. (This used to only occur when a packet that was timestamped
reached the software.) However the registers can't be read early otherwise
there is no way to correlate them to the packet.
This patch introduces a filter function which can be used to determine if a
packet should have been timestamped. Supplied with the filter setup by the
hwtstamp ioctl, check to make sure the PTP protocol and message type match the
expected values. If so, then read the timestamp registers (to free them.) At
this point check the descriptor bit, if the bit is set then we know this
packet correlates to the timestamp stored in the RXTSTAMP registers.
Otherwise, assume that packet was dropped by the hardware, and ignore this
timestamp value. However, we have at least unlocked the rxtstamp registers for
future timestamping.
Due to the way the driver handles skb data, it cannot be directly accessed. In
order to work around this, a copy of the skb data into a linear buffer is
made. From this buffer it becomes possible to read the data correctly
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling the hwtstamp mode for Rx timestamping the V2 ptp event type
specific modes (Delay Request and Sync) have been rolled into the V2 all event
packet modes, in order to more accurately represent what hardware is doing.
Hardware always timestamps the Path delay packets when a V2 mode is selected,
regardless of what type was selected (in order to always support Path delay
mode). However this means the user selected modes of timestamping only Sync or
Delay Request is not truly supported. This patch correctly sets the mode for
the hwtstamp config and returns to the user that all V2 event packets will be
timestamped.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes two minor nits from Richard Cochran. The first is a case of
ambitious line wrapping that wasn't necessary. The second is to re-order the
flag checks for PPS support. Previously, the hardware test was done first, and
the interrupt flag test was done second. Now, test the interrupt flag and use
the unlikely macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_sysfs.c is only needed when CONFIG_IXGBE_HWMON is configured in the
kernel.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Don Skidmore <Donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The flow control DV macros are used to calculate the flow control
high and low thresholds. This patch annotates these macros slightly
better and fixes the issues below.
The macro variables are renamed LINK to _max_frame_link and TC to
_max_frame_tc. This was to avoid confusion and make them more
readable. It was found that people auditing the code read TC to be
'traffic class' in the 802.1Q definition instead of the max frame
size of the tc. Hopefully it is clear now.
This audit also found the following real deviations from the
theoretical values. Fixed in this patch.
* I multiplied the DV calculations by (36/25) which always
evaluates to 1. This does not match the intended theoretical
value of 1.44.
* IXGBE_BT2KB added 1023 to account for rounding however this
really should be 8 * 1023 - 1 to account for division by 8k.
* x2 multiplication of max frame in DV calculations to account
for updated hardware recommendations.
With this patch the DV values are inline with the recommendations
in the 82599 and 82598 data sheets. Its worth noting I did not
see any dropped frames with flow control on in my experiments without
this patch. However aligning with the hardware specs and
recommendations seems like a good idea here to account for worst
case scenarios.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware bit IXGBE_RXD_STAT_VP appears to be set even when Rx
stripping is disabled. This results in passing frames up the stack
which do not have the 802.1Q tag stripped but have the tci bits
set as if it was.
Working around this with a check for the feature flag bit. I
would welcome any better ideas or a pointer to exactly which
bits in the hardware register need to be cleared to get the
IXGBE_RXD_STAT_VP bit to be set per data sheet.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB can be used independent of if RX VLAN stripping is enabled
or disabled so remove erroneous check.
Also enable or disable VLAN stripping when features are applied so
hardware and feature flags are in sync.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update version number to better match the version of the out of tree
driver with similar functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the hwmon code was initially added it was with the assumption that a
sysfs patch would be also coming soon. Since that isn't the case some
clean up needs to be done. This patch does that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the MAC, in order to provide the best software
timestamps. This patch adds this call for that support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the ethtool get_ts_info operation, which enables
access of available timestamp/timesync support for that device. It can query
which ptp clock device is associated with the particular port.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current value of the udelay timeout for ixgbe_disable_rx_buff is too
short. This causes the security path to not not be properly disabled during
the section that is meant to have it turned off. The end result causes a race
condition that results in RX issues.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the PPS system in the PHC framework, by enabling
the clock-out feature on the X540 device. Causes the SDP0 to be set as
a 1Hz clock. Also configures the timesync interrupt cause in order to
report each pulse to the PPS via the PHC framework, which can be used
for general system clock synchronization. (This allows a stable method
for tuning the general system time via the on-board SYSTIM register
based clock.)
Signed-off-by: Jacob E Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables hardware timestamping for use with PTP software by
extracting a ns counter from an arbitrary fixed point cycles counter.
The hardware generates SYSTIME registers using the DMA tick which
changes based on the current link speed. These SYSTIME registers are
converted to ns using the cyclecounter and timecounter structures
provided by the kernel. Using the SO_TIMESTAMPING api, software can
enable and access timestamps for PTP packets.
The SO_TIMESTAMPING API has space for 3 different kinds of timestamps,
SYS, RAW, and SOF. SYS hardware timestamps are hardware ns values that
are then scaled to the software clock. RAW hardware timestamps are the
direct raw value of the ns counter. SOF software timestamps are the
software timestamp calculated as close as possible to the software
transmit, but are not offloaded to the hardware. This patch only
supports the RAW hardware timestamps due to inefficiency of the SYS
design.
This patch also enables the PHC subsystem features for atomically
adjusting the cycle register, and adjusting the clock frequency in
parts per billion. This frequency adjustment works by slightly
adjusting the value added to the cycle registers each DMA tick. This
causes the hardware registers to overflow rapidly (approximately once
every 34 seconds, when at 10gig link). To solve this, the timecounter
structure is used, along with a timer set for every 25 seconds. This
allows for detecting register overflow and converting the cycle
counter registers into ns values needed for providing useful
timestamps to the network stack.
Only the basic required clock functions are supported at this time,
although the hardware supports some ancillary features and these could
easily be enabled in the future.
Note that use of this hardware timestamping requires modifying daemon
software to use the SO_TIMESTAMPING API for timestamps, and the
ptp_clock PHC framework for accessing the clock. The timestamps have
no relation to the system time at all, so software must use the posix
clock generated by the PHC framework instead.
Signed-off-by: Jacob E Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF sends a MACVLAN request with index of zero then it is not
actually trying to add a filter. Check the index value and only
indicate that operation is not allowed when the VF is actually trying
to add a filter.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The drop enable bit can be used to improve the performance of the adapter
in the case of multiple queues being present. This performance gain is due
to the fact that some slower CPUs can cause the FIFO to backfill preventing
faster CPUs from receiving additional work. By setting the drop enable bit
we prevent this and instead just drop the packets that would have been
bound for the slower CPU.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up the logic in the priority based flow control
configuration routines. Both the 82599 and 82598 based routines perform
similar functions however they are both arranged completely differently.
This patch goes over both of them to clean up the code.
In addition I am dropping the ixgbe_fc_pfc flow control mode and instead
just replacing it with checks for if priority flow control is enabled.
This allows us to maintain some of the link flow control information which
allows for an easier transition between link and priority flow control.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we would get a mailbox error and still process the message.
Instead we should exit on error.
In addition we should also be flushing the ACK of the message so that we
can guarantee that the other end is aware we have received the message
while we are processing it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
PFC stats are only tabulated when PFC is enabled. However in IEEE
mode the ieee_pfc pfc_tc bits were not checked and the calculation
was aborted.
This results in statistics not being reported through ethtool and
possible a false Tx hang occurring when receiving pause frames.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb and ixgbe incorrectly call netdev_tx_reset_queue() from
i{gb|xgbe}_clean_tx_ring() this sort of works in most cases except
when the number of real tx queues changes. When the number of real
tx queues changes netdev_tx_reset_queue() only gets called on the
new number of queues so when we reduce the number of queues we risk
triggering the watchdog timer and repeated device resets.
So this is not only a cosmetic issue but causes real bugs. For
example enabling/disabling DCB or FCoE in ixgbe will trigger this.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: John Bishop <johnx.bishop@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the link flow control configuration so that we
correctly set the link flow control settings for DCB. Previously we would
have to call the fc_enable call 8 times, once for each packet buffer. If
we move that logic into the fc_enable call itself we can avoid multiple
unnecessary register writes.
This change also corrects an issue in which we were only shifting the water
marks for 82599 parts by 6 instead of 10. This was resulting in us only
using 1/16 of the packet buffer when flow control was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck