Currently fifo transfer is started when submitting a transfer
request. Add posibility to defer the fifo transfer and start it
later by calling additional function. This change is backward
compatible, the behaviour of mpc52xx_lpbfifo_submit() is the same
for previous driver users, so there is no need to adapt them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Work around a silicon bug in the ac97 reset functionality of the
mpc5200(b). The implementation of the ac97 "cold" reset is flawed.
If the sync and output lines are high when reset is asserted the
attached ac97 device may go into test mode. Avoid this by
reconfiguring the psc to gpio mode and generating the reset manually.
From MPC5200B User's Manual:
"Some AC97 devices goes to a test mode, if the Sync line is high
during the Res line is low (reset phase). To avoid this behavior the
Sync line must be also forced to zero during the reset phase. To do
that, the pin muxing should switch to GPIO mode and the GPIO control
register should be used to control the output lines."
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Merge the WDT code into the GPT interface.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch changes the period parameter of mpc52xx_gpt_start_timer to
a u64 to support larger timeout periods.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is a driver for the FIFO device on the LocalPlus bus on an mpc5200 system.
The driver supports programmed I/O through the FIFO as well as setting up DMA
via the BestComm engine through the FIFO.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the utility function mpc52xx_get_xtal_freq() to get
the frequency of the external oscillator clock connected to the pin
SYS_XTAL_IN. The MSCAN may us it as clock source. Unfortunately, this
value is not available from the FDT blob, but it can be determined
from the IPB frequency.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds documentation to the mpc5200 interrupt controller
driver and cleans up some minor coding conventions. It also moves the
contents of mpc52xx_pic.h into the driver proper (except for a small
common bit that is moved to the common mpc52xx.h) because the
information encoded there is not required by any other part of kernel
code. Finally for code readability sake, the L2_OFFSET shift value
is removed because the code using it resolves to a noop.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Anatolij Gustschin