Use a string to specific the wakeup mode to make it more readable.
Add the Real-time Clock Wake-up support too for sam9g45 and sam9x5.
Add AT91_SHDW_CPTWK0_MAX to specific the Max of the Wakeup Counter.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
We can now drop the call to ioremap_registers() as we have the binding for the
SDRAM/DDR Controller.
Drop ioremap_registers() for sam9x5 too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Specified the main Oscillator via clock binding.
This will allow to do not hardcode it anymore in the DT board at 12MHz.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
http://www.calao-systems.com/articles.php?lng=en&pg=6099
this daughter board add the following device:
- Micro-SD socket
- TTL 3V3 - (Tx/Rx/RTS/CTS)
- I2C port
- 0.96" Serial OLED Display Module (over UART)
- MP3 decoder with Micro & Speakers
- 4x PB, 4x Leds (Blue), 3x Leds (Green, Orange, Red)
for now we add only the 2 UARTs, 4 Buttons, 7 leds and i2c via DT
used_led1 will not be re-add via DT as it's used by the motherboard too
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Use i2c-gpio and enable rv3029 RTC.
Enable the rtc in the sam9g20 defconfig.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Use a local copy of board informatin and fill with DT data.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file is including the SoC specific devices and properties. And
adds the dts file for SMDK5250 board which uses the EXYNOS5250
dts file. Its board specific properites will be added later.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for the new smp_twd runtime registration interface
to the imx6q platforms, and remove the old compile-time support.
The imx6q DTS file is updated to match the TWD DT documentation.
Also present in this patch a DTS fix to the timer interrupt routing
(the PPI connection uses bits [15:8]) and trigger (rising edge).
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add support for the new smp_twd runtime registration interface
to the highbank platforms, and remove the old compile-time support.
The highbank DTS file is updated to match the TWD DT documentation
and fixes the timer trigger (rising edge).
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
* 'dt-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ARM: OMAP2+: board-generic: Use of_irq_init API
arm/dts: OMAP3: Add interrupt-controller bindings for INTC
ARM: OMAP2/3: intc: Add DT support for TI interrupt controller
* 'dt' of git://github.com/hzhuang1/linux: (6 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
(plus update to v3.3-rc6)
The USB1 port on Tegra2 supports operation in host or device modes. On
Seaboard this is possible, so mark the port as OTG.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra's USB1 port supports legacy mode, so mark it as such. Even if we
don't use it, we must turn it off in the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Very basic support for TeeJet Mt.Ventoux board. Able to boot via
board-generic and ramdisk/initramfs, however most of peripherals are
not supported. Produces tons of twl4030 related errors as this board
doesn't have twl4030 installed.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tegra board updates. Most of the board updates for tegra30 and for some
of the driver device-tree conversions have gone in through the other
branches, so that leaves quite little left here -- mostly a couple
of updates to the not-yet-converted tegra2 boards and a couple of
device-tree updates.
* tag 'tegra-boards' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: match SoC name not board name in DT board files
ARM: tegra: PCIe: Provide 3.3V supply voltage
ARM: dt: tegra: add the wifi led to paz00 device tree
ARM: dt: tegra: add the power gpio key to paz00 device tree
ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tegra SoC driver support.
Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):
git://git.secretlab.ca/git/linux-2.6.git irqdomain/next
* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
ARM: tegra: uncompress.h: Don't depend on kernel headers
gpio: tegra: Fix build issue due to irq_domain rework.
ARM: tegra: Remove duplicate PMU interrupt inversion code
ARM: tegra: Add a simple PMC driver
ARM: tegra: dma: not required to move requestor when stopping.
ARM: tegra: Fix EMC pdata initialization from registers
gpio: tegra: Parameterize the number of banks
gpio: tegra: Dynamically allocate IRQ base, and support DT
ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
ARM: tegra: uncompress.h: Choose a UART at runtime
ARM: tegra: uncompress.h: Store UART address in a variable
ARM: tegra: Introduce define DEBUG_UART_SHIFT
ARM: tegra: Support Tegra30 in decompressor UART setup
ARM: tegra: Pause DMA when reading transfer count
ARM: tegra: emc: device tree support
ARM: tegra: emc: convert tegra2_emc to a platform driver
ARM: tegra: fuse: add bct strapping reading
ARM: tegra: fuse: add functions to access chip revision
ARM: tegra: fuse: use apbio dma for register access
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ports are used as follows:
UART1/A: Routed to debug dongle
UART2/B: GPS
UART3/C: Bluetooth
UART4/D: Routed to debug dongle
UART5/E: Not connected
The debug dongle has jumpers to connect either UART1/A or UART4/D to
the DB-9 connector. UART1/A is typically used on Cardhu, and is the option
we assume here.
For now, only enable UART1/A, and explicitly disable all other ports.
The explicit disable prevents the message "of_serial 70006040.serial:
no clock-frequency property set" being printed during boot.
Enabling the other ports requires their clocks to be enabled, or accesses
to the registers will hang. At present, this requires adding entries into
board-dt-tegra30.c's tegra_dt_clk_init_table[]. Lets punt on that and wait
for the common clock bindings to set this all up, although that will also
requiring adding clock support to 8250.c.
While we're at it, fix board-dt-tegra30.c to enable the correct clock for
the debug UART. We got away with this before, because the bootloader already
enabled it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds device tree binding of digital microphone to PAZ00
board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
This enables HW performance measurements, and usage of the "perf" tool.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'features/imx27-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
devicetree-bindings: Add documentation for i.MX generic boards
ARM i.MX: Add phytec phycore-i.MX27 (aka pcm038) devicetree support
ARM i.MX27: Add devicetree support
* 'at91-3.4-cleanup2+DT' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
ARM: at91/tclib: take iomem size from resource
ARM: at91/pit: add traces in case of error
ARM: at91: pit add DT support
ARM: at91: AIC and GPIO IRQ device tree initialization
ARM: at91/board-dt: remove AIC irq domain from board file
ARM: at91/gpio: remove the static specification of gpio_chip.base
ARM: at91/gpio: add .to_irq gpio_chip handler
ARM: at91/gpio: non-DT builds do not have gpio_chip.of_node field
ARM: at91/gpio: add irqdomain and DT support
ARM: at91/gpio: change comments and one variable name
ARM/USB: at91/ohci-at91: remove the use of irq_to_gpio
...
These two branches are a dependency for the at91 device tree changes,
so we pull them in here. at91/base2+cleanup will get merged through
the arm-soc cleanup2 branch, while the irqdomain tree will be sent
by Grant before this one gets integrated.
Conflicts:
drivers/rtc/rtc-at91sam9.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the gpio for d7 as we do not support yet the pwm led via dt.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds the support for new PIO controller found on some
at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
- support for several IRQ triggering features (type and polarity)
Support for those new features are retrieved from the device tree
compatibility string.
Debugfs at91_gpio file is updated to monitor configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Device tree support added to atmel_tclib: the generic Timer Counter
library. This is used by the clocksource/clockevent driver tcb_clksrc.
The current DT enabled platforms are also modified to use it:
- .dtsi files are modified to add Timer Counter Block entries
- alias are created to allow identification of each block
- clkdev lookup tables are added for clocks identification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Retreive registers address and IRQ from device tree entry.
Called from at91_dt_init_irq() so that timers are up-n-running
when timers initialization will occur.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change error path and interrupts property handling]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add "legacy" type of irqdomain to preserve old-style numbering
and allow smooth transition for both DT and non-DT cases.
Original idea and code by Jean-Christophe Plagniol-Villard.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Add an irqdomain for the AIC interrupt controller.
The device tree support is mapping the registers and
is using the irq_domain_add_legacy() to manage hwirq
translation.
The documentation is describing the meaning of the
two cells required for using this "interrupt-controller"
in a device tree node.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Add support for TI OMAP3 EVM board
arm/dts: OMAP4: Update DTS file with new GIC bindings
arm/dts: OMAP3: Add i2c controller nodes
arm/dts: OMAP4: Add i2c controller nodes
ARM: OMAP2+: Set Kconfig dependencies for PROC_DEVICETREE
arm/dts: OMAP3&4: Remove the '0x' prefix for serial nodes
ARM: OMAP1: kconfig: Enable IRQ_DOMAIN by default for OMAP1 platforms
ARM: OMAP2+: pm: Do not init statically the SR and voltage layer with DT
ARM: OMAP2+: omap_device: Replace dev_warn by dev_dbg in omap_device_build_from_dt
ARM: OMAP2+: board-generic: Remove un-needed .atag_offset for DT_MACHINE
ARM: OMAP2+: kconfig: Enable devicetree by default for OMAP2+ systems
arm/dts: OMAP: Remove bootargs node from board files
This patch adds basic devicetree support for i.MX27 based SoCs.
Only the bindings for which drivers exist are added here:
- UART
- fec
- CSPI
- I2C
- watchdog
- gpio
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This uart is the primary console for the dreamplug. Removed
kirkwood_uart0_init() call from board-dt.c.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.
After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support. First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.
Driver porting will start with the uart (see next patch), and progress
from there. Possibly, spi/flash/partitions will be next.
When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Update the DTS with the proper information required by the
INTC bindings.
- Add the number of interrupt lines
- Add the reg and the compatible entries.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cardhu uses Tegra's SD ports as follows:
SDMMC1: User SD slot, with GPIOs for power, CD, and WP.
SDMMC2: Not used
SDMMC3: WiFi (currently disabled pending future investigation)
SDMMC4: Internal eMMC
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add OMAP3 EVM (OMAP3530, AM/DM37x) DTS file to use the omap3.dtsi SoC file,
along with memory node information.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The GIC binding was updated in 3.2 and expects 3 interrupt-cells.
- Update the #interrupt-cells
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add i2c controllers nodes into the main ocp bus.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Add i2c controllers nodes into the main ocp bus.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds Device Tree file for the CoreTile Express A15x2
(V2P-CA15) with Test Chip 1.
As the chip's GIC has 160 interrupt inputs and equivalent SMM
(FPGA) has GIC synthesised with 256 interrupts, NR_IRQS is
increased.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
This patch adds generic Versatile Express DT machine description,
Device Tree description for the motherboard and documentation for
the bindings.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Follow the DTS convention and thus name the nodes <name>@<address> without
any '0x' prefix in the physical address.
Suggested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
* 'v3.3-samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (2 commits)
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
Linux 3.3-rc3
This includes an update to the v3.3-rc3 release from v3.3-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit db0d4db22a ('ARM: gic: allow GIC to support non-banked setups)
requires a cpu-offset property to be specified for non-banked gic
controllers, which is the case for Exynos4.
Reported-and-Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This adds the wifi led bound to the rfkill0 event to the device
tree of paz00.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the wakeup gpio which is connected to the embedded
controller to the device tree of paz00.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the ADT7461 temperature monitoring IC which is connected via
the DVC controller.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
UARTC is connected to the mini-pcie port.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The power gpio for the external memory card was specified wrongly.
Replace it with the correct value (tested with warmboot with fastboot).
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.
Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.
Update tegra*.dtsi to specify the required interrupt-related properties.
Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch is adding device tree support of headset autodetection on PAZ00 board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds initial device tree support of ALC5632 sound codec and
machine driver for PAZ00 board. The implementation is based on the WM8903 codec.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra PMC (Power Management Controller) interfaces with an external
PMU (Power Management Unit), and controls wake-up from sleep modes.
This initial binding is the bare minimum required to control the PMC's
inversion of the PMU's interrupt signal.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add complete bindings to instantiate and configure the codec and
top-level audio complex on all currently supported boards using the
Tegra+WM8903 audio driver.
On those boards, disable the I2S2 controller since it isn't used.
On boards not using the WM8903 codec, disable all the audio devices;
they can be re-enabled once the relevant codec and ASoC machine drivers
have been ported to device-tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This will allow the sound node to refer to the I2S controllers by name
when creating phandles.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Adjust the dma-channel property name to match the binding implemented by
the driver. The binding was implemented and documented in a
separate change to the ASoC tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Document binding, and add the node to tegra*.dtsi.
The driver isn't actually instantiated from this node yet, but the I2S
binding will rely on being able to refer to the APB DMA node using a
phandle.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Tegra30 GPIO controller has one more bank than Tegra20, and hence
has one more interrupt.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
The new content matches tegra20.dtsi, and is < 80 columns.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
Device tree include file for the AT91SAM9x5 SoC family.
An additional .dtsi file is created to describe the generic
SAM9x5 CPU Module (CM).
Device tree source files for each Evaluation Kit that are using
the generic CPU Module and the carrier board. The selection of
available peripherals is done in this .dts file.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Compiled device tree blobs shouldn't be committed in the kernel
tree, so ideally git should ignore them.
This patch will enable ignoring of any .dtb files which appear in
arch/arm/boot/
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a helper function for finding the index of a string in a string
list property. This helper is useful for bindings that use a separate
*-name property for attaching names to tuples in another property such
as 'reg' or 'gpios'.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Kbuild: Use dtc's -d (dependency) option
dtc: Implement -d option to write out a dependency file
kbuild: Fix comment in Makefile.lib
scripts/genksyms: clean lex/yacc generated files
kbuild: Correctly deal with make options which contain an "s"
This hooks dtc into Kbuild's dependency system.
Thus, for example, "make dtbs" will rebuild tegra-harmony.dtb if only
tegra20.dtsi has changed yet tegra-harmony.dts has not. The previous
lack of this feature recently caused me to have very confusing "git
bisect" results.
For ARM, it's obvious what to add to $(targets). I'm not familiar enough
with other architectures to know what to add there. Powerpc appears to
already add various .dtb files into $(targets), but the other archs may
need something added to $(targets) to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
[mmarek: Dropped arch/c6x part to avoid merging commits from the middle
of the merge window]
Signed-off-by: Michal Marek <mmarek@suse.cz>
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=P4kO
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
power management changes for omap and imx
A significant part of the changes for these two platforms went into
power management, so they are split out into a separate branch.
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (65 commits)
ARM: imx6: remove __CPUINIT annotation from v7_invalidate_l1
ARM: imx6: fix v7_invalidate_l1 by adding I-Cache invalidation
ARM: imx6q: resume PL310 only when CACHE_L2X0 defined
ARM: imx6q: build pm code only when CONFIG_PM selected
ARM: mx5: use generic irq chip pm interface for pm functions on
ARM: omap: pass minimal SoC/board data for UART from dt
arm/dts: Add minimal device tree support for omap2420 and omap2430
omap-serial: Add minimal device tree support
omap-serial: Use default clock speed (48Mhz) if not specified
omap-serial: Get rid of all pdev->id usage
ARM: OMAP2+: hwmod: Add a new flag to handle hwmods left enabled at init
ARM: OMAP4: PRM: use PRCM interrupt handler
ARM: OMAP3: pm: use prcm chain handler
ARM: OMAP: hwmod: add support for selecting mpu_irq for each wakeup pad
ARM: OMAP2+: mux: add support for PAD wakeup interrupts
ARM: OMAP: PRCM: add suspend prepare / finish support
ARM: OMAP: PRCM: add support for chain interrupt handler
ARM: OMAP3/4: PRM: add functions to read pending IRQs, PRM barrier
ARM: OMAP2+: hwmod: Add API to enable IO ring wakeup
ARM: OMAP2+: mux: add wakeup-capable hwmod mux entries to dynamic list
...
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...