Fix a race between cfg80211 add_key call and transmitting of 4/4 EAP
packet. In case the transmit is delayed until after the add key takes
place, message 4/4 will be encrypted with the new key, and the
receiver side (AP) will drop it due to MIC error.
Wil6210 will monitor and look for the transmitted packet 4/4 eap key.
In case add_key takes place before the transmission completed, then
wil6210 will let the FW store the key and wil6210 will notify the FW
to use the PTK key only after 4/4 eap packet transmission was
completed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMC is a hardware debug mechanism which allows capturing real time
debug data and stream it to host memory. The driver allocates memory
buffers and set them inside PMC ring of descriptors.
Add pmcring debugfs that application can use to read the binary
content of descriptors inside the PMC ring (cat pmcring).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move common part of wil_netif_rx_any into new helper function and add
support for non-gro receive using netif_rx_ni.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tlv targets such as WCN3990 send more data in the chan info event, which is
not sent by the non tlv targets. There is a minimum size check in the wmi event
for non-tlv targets and hence we cannot update the common channel info
structure as it was done in commit 13104929d2 ("ath10k: fill the channel
survey results for WCN3990 correctly"). This broke channel survey results on
10.x firmware versions.
If the common channel info structure is updated, the size check for chan info
event for non-tlv targets will fail and return -EPROTO and we see the below
error messages
ath10k_pci 0000:01:00.0: failed to parse chan info event: -71
Add tlv specific channel info structure and restore the original size of the
common channel info structure to mitigate this issue.
Tested HW: WCN3990
QCA9887
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
10.2.4-1.0-00037
Fixes: 13104929d2 ("ath10k: fill the channel survey results for WCN3990 correctly")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the FW bundles multiple packets, pkt->act_len may be incorrect
as it refers to the first packet only (however, the FW will only
bundle packets that fit into the same pkt->alloc_len).
Before this patch, the skb length would be set (incorrectly) to
pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually
adjusted in ath10k_sdio_mbox_rx_process_packet.
The first problem is that ath10k_sdio_mbox_rx_process_packet does not
use proper skb_put commands to adjust the length (it directly changes
skb->len), so we end up with a mismatch between skb->head + skb->tail
and skb->data + skb->len. This is quite serious, and causes corruptions
in the TCP stack, as the stack tries to coalesce packets, and relies
on skb->tail being correct (that is, skb_tail_pointer must point to
the first byte_after_ the data).
Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet,
this moves the code to ath10k_sdio_mbox_rx_packet, and also add a
bounds check, as skb_put would crash the kernel if not enough space is
available.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Fixes: 8530b4e7b2 ("ath10k: sdio: set skb len for all rx packets")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My wave-1 firmware often crashes when I am bringing down
AP vdevs, and sometimes at least some machines lockup hard
after spewing IOMMU errors.
I don't see the same issue in STA mode, so I suspect beacons
are the issue.
Moving the beacon buf deletion to later in the vdev teardown
logic appears to help this problem. Firmware still crashes
often, but several iterations did not show IOMMU errors and
machine didn't hang.
Tested hardware: QCA9880
Tested firmware: ath10k-ct from beginning of 2019, exact version unknown
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
-----BEGIN PGP SIGNATURE-----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=HAuT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes, but things are settling down:
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some features of 802.11ax without central organizing (AP) STA can also be
used in mesh mode. hwsim can be used to assist initial development of these
features without having access to HW.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Link: https://lore.kernel.org/r/20190813063657.7544-1-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ath9k_wmi_cmd, the allocated network buffer needs to be released
if timeout happens. Otherwise memory will be leaked.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In htc_config_pipe_credits, htc_setup_complete, and htc_connect_service
if time out happens, the allocated buffer needs to be released.
Otherwise there will be memory leak.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath9k_reg_rmw_single do not need return value to cope with different
cases. And change functon return type to void.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For sdio chip, if the rssi is not good, then it have some retry,
firmware will indicate the msdu list of a ppdu with a hole, it
means it lost the hole msdu, after the msdu retry from AP, the
hole msdu will indicate from firmware later. The hole msdu's PN
check will fail and the hole msdu will be dropped.
PN check fail example:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3818 6105 success
3819 6106 success
3820 6107 success
3817 6104 fail
The correct logic is reorder the msdu list and then do PN check.
ieee80211_rx_reorder_ampdu of mac80211 will do the reorer logic
and then do PN check in ieee80211_rx_h_decrypt of mac80211.
example after reorder:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3817 6104 success
3818 6105 success
3819 6106 success
3820 6107 success
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For PMF case, the action,deauth,disassoc management need to encrypt
by hardware, it need to reserve 8 bytes for encryption, otherwise
the packet will be sent out with error format, then PMF case will
fail.
After add the 8 bytes, it will pass the PMF case.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Remove (broken) d0i3 support;
* Debug infrastructure work continues;
* Bump support FW API version to 50;
* Fix for the SN value in certain suspend/resume situations;
* Some work on new FW scan APIs;
* Work on LTR FW APIs;
* New FW channel-switch support;
* Support new ACPI value for per-platform antenna gain;
* Support for single antenna diversity;
* Support for new WoWLAN FW API;
* Initial refactoring of the device selection code;
* A bunch of clean-ups;
* Other small fixes and improvements;
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEF3LNfgb2BPWm68smoUecoho8xfoFAl1yXFYACgkQoUecoho8
xfr1og/8C2CYJ7dDg/uWBUHu1L8YvukNf4/DoMkrioJ5dVBKt37v+LDqSRTssnvm
m9kbeEwu7nyNaX1YRLnK16lwthaOlIUcp7cnmJWF6JaIFmZeGFN8mdV2ccEKFJnk
iAoWrlXWcHQ4NI6e5gw+JzunxSa86czV/jl7JETLxMu8y3FH5dg3sEIVjc4uIyq1
u91SPwxF+hUIlP5UAYvBJSzBLug3o/Fn6kMXiGG+spf2gAWVfYgQm8YIV9aJ+nb+
+R2BKNFzuMa76Y5VeacV+DUqNQ5sPvr3Q8Ftagkg3g0w0aKJcMlZ9tJCZhNCo+HK
Fja6oQODsG2pVkYnPTDc4VZ3PHigebsCztiX2oNIReSSrTPAJMH2+LTp7KWY0j1h
a5hzQWf2OLRVFRbPTW6cgT2Fd+v2ywG4HnAHIRtkiCl8L/118AK42zBVxbzaSk3r
aq2/LfDVQ1fe9Rp6T+ZsSckc1Y2loEW3zAu9obiERw6//WS3DuWbGotBbsoDo29C
cD8kSGuoeaDl4T/J44tGWfubbTRuii061/zkNtX5cHPhYs6Kc1U5Lyuoq+2yqbBR
tCATJFFnGT61Z3h4691Mp38teMzhkdv9LneIuy5gkSIPaDVk6NG2usfH1OTuaECK
kuaK8KvGUD3bdwoxudkl1owpncYTXWBVnDBA6GV4CVavU48PLjg=
=1L5G
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2019-09-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Patches intended for v5.4
* Remove (broken) d0i3 support;
* Debug infrastructure work continues;
* Bump support FW API version to 50;
* Fix for the SN value in certain suspend/resume situations;
* Some work on new FW scan APIs;
* Work on LTR FW APIs;
* New FW channel-switch support;
* Support new ACPI value for per-platform antenna gain;
* Support for single antenna diversity;
* Support for new WoWLAN FW API;
* Initial refactoring of the device selection code;
* A bunch of clean-ups;
* Other small fixes and improvements;
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: 610247f46f ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using single_open(), single_release() should be used instead
of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Obviously, variable 'copied' is initialized to zero. But it is not used.
hence just remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a trivial debugfs entry for triggering reset just like in case
of firmware crash. It works by writing 1 to it:
echo 1 > reset
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of compiling driver without DEBUG expose a stub function to make
writing debug code much simpler (no extra conditions). This will allow
e.g. using debugfs_create_file() without any magic if or #ifdef.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use cancel_delayed_work_sync on the dump workers only in case of
unloading the op mode. In any other case use iwl_fw_flush_dumps or
iwl_fw_dbg_stop_sync (depends if the op mode mutex is held or not).
This way, the driver will wait until debug data is collected in all
cases but op mode unloading.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove periodic trigger functionality.
After moving to the new API we will add periodic trigger functionality
that matches the new API.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the documentation of struct iwl_fw_ini_monitor_dump and
iwl_fw_ini_error_dump_range.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support code to be able to use the DRAM buffer allocation command,
which allows us to send information about a buffer to the firmware
to use it with the DBGC hardware.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the "apply points" mechanism as preparation for the changed
debug API where this is now a "time point" instead. Use a new API
across the code at the trigger points ("time points"), but don't
yet implement it since that requires some more preparation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to easily calculate array length at the end of a TLV.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes the firmware won't be able to decrypt frames
because the keys were not installed yet or other scenarios.
The firmware will soon stop dropping multicast frames when
MAC_FILTER_ACCEPT_GRP is not set. The firmware will simply
always pass multicast frame in.
In order to avoid logging any such frame coming in when we
don't have the keys, drop the print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are products which have a single chain with 2 antennas.
In these products, we need to inform the FW that the device has the
single antenna diversity(SAD) feature. In the future, we will read
the active antenna from a BIOS configuration. Currently, we use a
default configuration which means that the FW decides which antenna to use.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In prior hardware generations (e.g. 9000 series), we received the BAR
frame with fake NSSN information to handle releasing frames from the
reorder buffer for the default queue, the other queues were getting
the FRAME_RELEASE notification in this case.
With multi-TID block-ack, the firmware no longer sends us the BAR
frame because the fake RX is quite big (just the metadata is around
48 bytes or so). Instead, it now sends us one (or multiple) special
release notifications (0xc2). The hardware consumes these as well,
but only generates the FRAME_RELEASE (0xc3) for queues other than
the default queue. We thus need to handle them in the same way we
handle the normal FRAME_RELEASE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Certain APs (I think a certain Broadcom model) interact badly with our
full state BA bitmap handling, and if triggered badly with many powersave
transitions they keep sending frames from before the window, which our
hardware then doesn't appear to ACK (to them) since it has moved on and
is sending ACKs for higher SNs now.
Try to detect this situation and if this keeps happening, disable the
aggregation session.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
WoWlan feature within the FW uses the station id for various of reasons.
Thus we need to add this information to the command.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new device generation has a slightly different suspend resume flow
Currently, the way the driver instruct the device to move to D3 is by
sending D3_CONFIG_CMD.
Instead of using the host command the indication is by writing to the
doorbell interrupt.
The FW will respond with interrupt to indicate transition completion.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove duplicate inclusion of iwl-trans.h.
This issue was found by includecheck.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few functions were receiving the iwl_cfg struct directly, but we
will also need other parts of the trans, so pass the trans (which
includes the cfg) to them.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of accessing the iwl_config_trans_params from the cfg that is
stored in the trans struct, pass this structure directly to functions
that need it during trans_alloc. This will be useful to isolate the
elements needed during allocation and pass them separately before the
actual cfg struct is known.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the cfg to iwl_trans already during allocation, set
it only later when we have had the time to decide which cfg to use.
This is part of the effort to be able to decide the cfg based on HW
revision and RF ID after iwl_trans_alloc() has been called.
For now, since we still have a bunch of code checking the HW revision
and the RF ID, we set iwl_trans->cfg early, even before we decided the
real cfg to use. We only use the trans configuration at this point,
so this is fine for now. In the future, the trans configuration will
be completely independent from the rest of the config structure, so
we'll be able to avoid this.
Additionally, we can't access the PRPH registers in iwl_trans_alloc()
anymore, so move the HW REV C-step check for family 8000 code later to
the probe function as well. This step is probably not necessary, but
if that's the case it should be removed separately later on.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There were a couple of special handling to find the correct cfg inside
iwl_trans_pcie_alloc(). Move them to iwl_pci_probe() so they're
together with the rest of the decisions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of using iwl_trans->cfg in iwl_trans_pcie_alloc(), use the
local argument that we received. This will allow us to not to set the
cfg during iwl_trans_alloc() so it can be decided later.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make a static regions ops array and use it instead of switch case when
determining what op to use to collect a region.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid iterating over dump TLVs twice for size calculation by using
linked list to store the dump TLVs.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
separate configuration flows and dump collection flows.
make ini configuration flows be in iwl-dbg-tlv.c and dump related flows
in dbg.c to better reflect their logical difference.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Can't rely that band 2.4 is always supported by the NIC and use the
first channel in this band for the phy ctxt.
Instead, look for the first channel in the first band that is supported
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of Ultra-high-band (UHB), need to allocate nvm data structure in
size of UHB channels array.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the IWL_DEVICE_AX200_COMMON definition, since it's only used
once and relies mostly on IWL_DEVICE_22000_COMMON anyway.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align wrt log prints to the driver coding style
Remove the ext field from the log and print it at the beginning of the
apply point.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug flow TLV was removed from the FW. Remove the TLV from the driver
as well.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reimplement debug TLV allocation flow. The driver will check the
validity of the debug TLVs prior allocating space for them.
Any malformed or unsupported TLV will be skipped.
The TLV specific checks will be added in later patches.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
use iwl_trans_dbg_ini_valid function instead of a boolean value check if
dbg_ini mode is on. It is needed for a future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The string we define as IWL_22000_HR_B_F0_FW_PRE is duplicate with
IWL_22000_QU_B_HR_B_FW_PRE. Remove the former to avoid confusion.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The real name is struct iwl_tof_range_req_ext_cmd, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TX power limits as defined in the OTP assume the worst case scenario
in terms of the platform's atenna gain, but most platforms are below
that value so they can use more TX power without passing the regulatory
limit. If the platform indicates in the BIOS that it indeed has lower
gain, and the geographic location allows it, higher TX power can be
used. The driver reads the PPAG (Per-Platform Antenna Gain) data from
BIOS (if it exists), validates it and sends the appropriate command to
the FW. This flow happens once at FW init, in case of suspend/resume
there is no need to read again from BIOS as we save those values during
init, so just send the PPAG command again to FW.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The check is not necessary anymore, because now the struct is not
allocated separately, but is part of the mvmsta struct. Remove the
check, since it's dead code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Any firmware that supports the new channel switch flow is
able to close / re-open the queues when needed. It takes
into account the channel switch mode etc...
Don't open / close the queues or enable / disable beacon
abort before and after the channel switch in case the
firmware is able to do this by itself.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
dma_alloc_coherent is not just the page allocator. The only valid
arguments to pass are either GFP_ATOMIC or GFP_ATOMIC with possible
modifiers of __GFP_NORETRY or __GFP_NOWARN.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
periphery phy and aux regions should not be collected like periphery mac
region. Remove their handling. The handling will be added in the future
once the FW will support it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use a linked list to maintain the debug TLVs instead of a single buffer.
This way, the driver does not need to iterate over the binary file twice
and allocates smaller chunks of memory. Also, in case one allocation
fails the driver will work with the partial configuration instead of
aborting the entire debug configuration.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Maintain DRAM debug buffer status in trans instead of keeping it as
part of the TLVs buffer to avoid allocating extra space for it.
Needed for future changes.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
regdb_ptrs is not in used anymore, remove it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
align the naming to iwl_dbg_tlv_*
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Function iwl_mvm_scan_set_legacy_probe_req() second argument
size is too large to be passed by value.
Fix it to be passed by reference.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the now unneeded functions that called those from the
transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is always set to IWL_PLAT_PM_MODE_DISABLED
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state, FW may send packets.
As a result, "write" queue pointer will be incremented by FW.
Upon resume from D3, driver should adjust its shadows of "write" and "read"
pointers to the value reported by FW.
1. Keep TID used during wowlan configuration.
2. Upon resume, set driver's "write" and "read" queue pointers
to the value reported by FW.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It doesn't make sense to use the FW thermal monitoring only if we
have CONFIG_THERMAL, because then we use the default thresholds
etc. which may be different from what the firmware implements, as
we don't maintain them in the driver now. Only the CTDP code needs
to actually be under CONFIG_THERMAL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's hard to follow the numbers so rename it with enum
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Scan API was changed to support 6Ghz channels as well.
Support the new version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New FW versions introduces LTR feature enablement by default.
For such FW versions, driver (mvm/xvt) should not send
host command to enable LTR feature, also it should be possible to
override LTR configuration through the debugfs.
1. Send LTR feature enablement command only for FW versions
which does not advertises SET_LTR_GEN2 capability.
2. Implement ltr_config file in debugfs for LTR configuration override.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
This flag should never be set unless integration work with the
platform is done. We don't support any platforms officially and don't
plan to do so in the near future, so we can remove this option
entirely in order to avoid having it enabled by mistake.
This has been marked with "depends on EXPERT", so there shouldn't be
many systems running with it set. And, if there are systems, they
should not be using this flag.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This flag is never set on any host command. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We're now left with a status bit that is never set and a few
other leftovers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Also change the signature of the power functions that won't
receive d0i3=true anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This variable read, but never set. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that d0i3 is dead, this function can't be called from d0i3
flows. Change its signature and make it static.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For runtime PM to work with d0i3 code, a lot of integration work needs
to be done with the platform (e.g. the out-of-band wake up interrupt)
and we currently don't have any platforms where this integration
happened. So, this code has been pretty much stale for a while and
when someone enables it, it just breaks things.
Therefore, to simplify the code base and make sure no one enables this
by mistake, we will remove the whole code.
This is only the very start, much more work is needed.
Remove the places where we check iwl_mvm_is_d0i3_supported
but leave all the refs, those will be removed in a different
patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When printing a TX, add to the print the length of the frame.
That will help with BSEP (buffer status report poll) tests.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use the actual length of channels array and not the max capable length.
Signed-off-by: Beker Ayala <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
add support to print ldbg command in mvm and xvt mode
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new DBGC_SUSPEND_RESUME command to change the recording state.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The recording functions are quite big to be inline and the driver should
expose only the stop and restart functions that are allowed to be used
rather then the internal helper functions. Move the functions from the
header file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These static functions are only used after their definition,
so we don't need the forward declarations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case that there are OBSS that do not know how to properly
interpret 26-tone RU OFDMA transmissions, instruct the FW not
to use such transmissions.
The check is currently only performed upon association.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If mvm->fwrt.cur_fw_img != IWL_UCODE_INIT, then
rfkill_safe_init_done must be true since
rfkill_safe_init_done is set to true before we start to load
the runtime image.
Remove the redundant condition.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ahmad Masri