Add dmtimer clock aliases for AM33XX devices so that the parent clock for
the dmtimer can be set correctly by the dmtimer driver. Without these clock
aliases the dmtimer driver will fail to find the parent clocks for the dmtimer.
Verified that DMTIMERs can be successfully requested on AM335x beagle bone.
Original patch was provided by Vaibhav Hiremath [1]. Changelog and
additional verification performed by Jon Hunter.
[1] http://marc.info/?l=linux-omap&m=134693631608018&w=2
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After commit 24d7b40a60 (ARM: OMAP2+:
PM: MPU DVFS: use generic CPU device for MPU-SS), OPPs are registered
using an existing CPU device, not the omap_device for MPU-SS.
First, fix the board file to use get_cpu_device() as required by the
above commit, otherwise custom OPPs will be added to the wrong device.
Second, the board files OPP init is called from the its init_machine
method, and the generic CPU devices are not yet created when
init_machine is run. Therefore OPP initialization will fail. To fix,
use a device_initcall() for the board file's OPP customization, and
make the device_initcall board-specific by using a machine_is check.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On n900 uart1 pins are not not used for uart, instead they are
used to connect to a cell modem over ssi. Looks like we're
currently missing these signal names for 3430 for some reason,
and only have some of them listed for 3630. Obviously the signals
are there for 3430 if n900 is using them and they are documented
in some TRMs.
Note that these will eventually be replaced by device tree
based pinctrl-single.c driver. But for now these are needed
to verify the SSI pins for devices like Nokia N900.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8f31cefe (ARM: OMAP2+: select PINCTRL in Kconfig)
added select PINCTRL, but accdentally added it to a wrong
location.
We want to select if for ARCH_OMAP2PLUS, not for
ARCH_OMAP2PLUS_TYPICAL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The runtime PM framework assumes that the hardware state of devices
when initialized is disabled. For all omap_devices, we idle/disable
device by default. However, the console uart uses a "no idle" option
during omap_device init in order to allow earlyprintk usage to work
seamlessly during boot.
Because the hardware is left partially enabled after init (whatever
the bootloader settings were), the omap_device should later be fully
initialized (including mux) and the runtime PM framework should be
told that the device is active, and not disabled so that the hardware
state is in sync with runtime PM state.
To fix, after the device has been created/registered, call
omap_device_enable() to finialize init and use pm_runtime_set_active()
to tell the runtime PM core the device is enabled.
Tested on 2420/n810, 3530/Overo, 3530/Beagle, 3730/OveroSTORM,
3730/Beagle-xM, 4460/PandaES.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP34xx/35xx, and OMAP36xx chips with ES < 1.2, if the PER
powerdomain goes to OSWR or OFF while CORE stays at CSWR or ON, or if,
upon chip wakeup from OSWR or OFF, the CORE powerdomain goes ON before
PER, the UART3/4 FIFOs and McBSP2/3 SIDETONE memories will be
unusable. This is erratum i582 in the OMAP36xx Silicon Errata
document.
This patch implements one of several parts of the workaround: the
addition of the wakeup dependency between the PER and WKUP
clockdomains, such that PER will wake up at the same time CORE_L3
does.
This is not a complete workaround. For it to be complete:
1. the PER powerdomain's next power state must not be set to OSWR or
OFF if the CORE powerdomain's next power state is set to CSWR or
ON;
2. the UART3/4 FIFO and McBSP2/3 SIDETONE loopback tests should be run
if the LASTPOWERSTATEENTERED bits for PER and CORE indicate that
PER went OFF while CORE stayed on. If loopback tests fail, then
those devices will be unusable until PER and CORE can undergo a
transition from ON to OSWR/OFF and back ON.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently, if the GPMC driver fails to reserve memory when probed we will
call BUG() and the kernel will not boot. Instead of calling BUG(), return
an error from probe and allow kernel to boot.
Boot tested on AM335x beagle bone board and OMAP4430 Panda board.
V2 changes:
- Ensure that clock and memory resources are released on error.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previously the code only acquired spinlock after increasing / decreasing
the usecount value, which is wrong. This leaves a small window where
a task switch may occur between the check of the usecount and the actual
wakeup / sleep of the domain. Fixed by moving the spinlock locking before
the usecount access. Left the usecount as atomic_t if someone wants an
easy access to the parameter through atomic_read.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPMC code has been converted to a driver by the following commit:
commit da49687397
Author: Afzal Mohammed <afzal@ti.com>
Date: Sun Sep 23 17:28:25 2012 -0600
ARM: OMAP2+: gpmc: minimal driver support
It now requests a clock with con-id "fck" otherwise the probe will fails.
[ 0.342010] omap-gpmc omap-gpmc: error: clk_get
[ 0.346771] omap-gpmc: probe of omap-gpmc failed with error -2
Add the "omap-gmpc" dev-id and fck con-id to the already existing
gmpc-fck dummy clock.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal)
changed the interrupts to allow enabling sparse IRQ, but
accidentally added the omap3 INTC base to the local IRQ.
This causes the following:
twd: can't register interrupt 45 (-22)
twd_local_timer_register failed -22
The right fix is to not add any base, as it is a local
timer. For the OMAP44XX_IRQ_LOCALWDT we had defined earlier
there are no users, so no need to fix that.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because firmware
no longer sets up all pin states before starting the kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was pre-agreed).
- A longer series of misc regression fixes and cleanups, warning removals,
etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vAh+
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
From Tony Lindgren:
This branch contains regression fixes for omap4/5 ASoC
audio that were caused by the fact that u-boot stopped
muxing non essential pins.
As omap audio and dmaengine development happens on
these platforms, let's make sure they are usable.
Of course this should have been fixed earlier and
not during the -rc cycle.
* tag 'omap-for-v3.7-rc1/fixes-asoc-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
ARM: OMAP: board-4430-sdp: Pin mux configuration for audio needs
From Tony Lindgren:
These were agreed to be merged via arm soc tree as Rafael
is on vacation.
From Kevin Hilman <khilman@deeprootsystems.com>:
This series a couple bug fixes and a couple fixes that make this
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
* tag 'omap-for-v3.7-rc1/fixes-cpufreq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for MPU-SS
cpufreq: OMAP: use get_cpu_device() instead of omap_device API
cpufreq: OMAP: fix clock usage to be SoC independent, remove plat/ includes
cpufreq: OMAP: remove unused <plat/omap-pm.h>
cpufreq: OMAP: ensure valid clock rate before scaling
From Kevin Hilman <khilman@deeprootsystems.com> via Tony Lindgren:
OMAP PM related fixes for v3.7-rc
* tag 'omap-for-v3.7-rc1/fixes-pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: SmartReflex: fix error path in init function
ARM: OMAP: SmartReflex: select CONFIG_POWER_SUPPLY in Kconfig
ARM: OMAP2+: PM: fix return value check in omap2_set_init_voltage()
ARM: OMAP2+: SmartReflex: fix return value check in sr_dev_init()
ARM: OMAP: omap_device: fix return value check in omap_device_build_ss()
ARM: OMAP: fix return value check in beagle_opp_init()
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Some OMAP fixes for the 3.7 merge window, fixing mismerges, branch
integration issues, and bugs after the arm-soc merges.
* tag 'omap-for-v3.7-rc1/fixes-hwmod-clock-signed-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
ARM: OMAP: omap3evm: fix new sparse warning
ARM: OMAP2+: hwmod data: Fix PMU interrupt definitions
ARM: am33xx: clk: Update clkdev table to add mcasp alias
Commit eb05f69129 ("ARM: OMAP: hwmod:
partially un-reset hwmods might not be properly enabled") added code
to skip the IP block disable sequence if all of the block's hardreset
lines weren't asserted. But this did not handle the case when no
hardreset lines were associated with a module, which is the general
case. In that situation, the IP block disable would be skipped. This
is likely to cause PM regressions.
So, modify _omap4_disable_module() and _am33xx_disable_module() to
only bail out early if there are any hardreset lines asserted. And
move the AM33xx test above the actual module disable code to ensure
that the behavior is consistent.
Reported-by: Archit Taneja <a0393947@ti.com>
Tested-by: Archit Taneja <a0393947@ti.com> # DSS
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com> # AM335x
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b71c721 (ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU
clockdomain idle problems) added a workaround for the EMU clock domain on
OMAP3/4 devices to prevent the clock domain for transitioning while it is
in use.
In the proposed patch [1] code was added to the omap3xxx_clkdm_clk_enable()
and omap3xxx_clkdm_clk_disable() functions to check for the flag
CLKDM_MISSING_IDLE_REPORTING and perform the appropriate action. However, in the
merged patch it appears that this code was added to the omap2_clkdm_clk_enable()
and omap2_clkdm_clk_disable() functions by mistake.
[1] http://marc.info/?l=linux-arm-kernel&m=134383567112518&w=2
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use the enum for board_ref_clock from linux/wl12xx.h
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Pankaj Jangra<jangra.pankaj9@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. These pins are
essential for audio and need to be done to have working audio on the board.
Pin Mux configuration for: twl6040 audpwron gpio, McPDM, and McBSP1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. These pins are
essential for audio and need to be done to have working audio on the board.
Pin Mux configuration for: twl6040 audpwron gpio, McPDM, DMIC, McBSP1 and
McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kteZ
-----END PGP SIGNATURE-----
Merge tag 'for_3.7-fixes-cpufreq' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.7-rc1/fixes-cpufreq
This series a couple bug fixes and a couple fixes that make this
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
This patch adds a missing hwmod entry for the HDQ/1-Wire module present
in the AM3505/17 CPUs.
This restores 1-Wire support to our AM3505 boards. We think it probably
stopped working with commit 96b1b29d37
ARM: OMAP2+: HDQ1W: use omap_device
Signed-off-by: Raphael Assenat <raph@8d.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
compiler complained,
`gpmc_remove' referenced in section `.data' of arch/arm/mach-omap2/built-in.o: defined in discarded section `.exit.text' of arch/arm/mach-omap2/built-in.o
Annotate gpmc_remove function and dependents with __devexit.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
not NULL pointer. The NULL test in the return value check should
be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
not NULL pointer. The NULL test in the return value check should
be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support of
D3 clock-stop. Also changing the power_save option in sysfs kicks
off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in HD-audio
are continued cleanups and standardization for the generic auto
parser and bug fixes (HBR, device-specific fixups), in addition to
the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=uNqD
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
Currently, a dummy omap_device is created for the MPU sub-system so
that a device node exists for MPU DVFS. Specifically, for the
association of MPU OPPs to a device node, and so that a voltage
regulator can be mapped to a device node.
For drivers to get a handle to this device node, an OMAP-specific API
has been used. However, the kernel already has device nodes for the
CPU(s) in the system, so we can use those instead of an OMAP-specific
dummy device and then drivers (like OMAP CPUfreq) can use generic
APIs.
To use the existing CPU device nodes, modify the OPP creation and
regulator registration to use the CPU0 device node for registraion.
NOTE: this patch always uses CPU0 as the device node. On all
OMAPs today, MPU DVFS scales all CPUs together, so this will
not be a problem, but this assumption will need to be changed
if independently scalable CPUs are introduced.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
rx51_si4713_dev is referenced only from rx51_init_si4713.
So the memory for rx51_si4713_dev can be safely freed after init.
Also it references rx51_si4713_board_info which is __initdata_or_module.
fixes the below warning.
WARNING: vmlinux.o(.data+0x30958): Section mismatch in reference from the variable rx51_si4713_dev to the (unknown reference) .init.data:(unknown)
The variable rx51_si4713_dev references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
memblock_steal tries to reserve physical memory during boot.
When the requested size is not aligned on the section size
then, the remaining memory available for lowmem becomes
unaligned on the section boundary. There is a issue with this,
which is discussed in the thread below.
https://lkml.org/lkml/2012/6/28/112
The final conclusion from the thread seems to
be align the memblock_steal calls on the SECTION boundary.
The issue comes out when LPAE is enabled, where the
section size is 2MB.
Boot tested this on OMAP5 evm with and without LPAE.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit e54adb1e79 ("ARM: OMAP: omap3evm:
cleanup revision bits") adds a new sparse[1] warning:
arch/arm/mach-omap2/board-omap3evm.c:90:4: warning: symbol 'get_omap3_evm_rev' was not declared. Should it be static?
This symbol no longer appears to be used outside this file, so mark it
static and remove the export.
...
1. https://sparse.wiki.kernel.org/index.php/Main_Page
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit ec2c082
(ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ) updated the way
interrupts for OMAP2/3 devices are defined in the HWMOD data structures to
being an index plus a fixed offset (defined by OMAP_INTC_START). The definition
of the PMU interrupts on OMAP2/3 devices is missing the OMAP_INTC_START offset
and so this is causing the allocation of PMU interrupts to fail on OMAP2/3
devices. So add the offset to fix this.
This is patch is based upon Tony's master branch for OMAP.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After Rajendra's common-clock preparation series,
commit (a1978ef4da1 - ARM: omap: hwmod: get rid of
all omap_clk_get_by_name usage) the clkdev table need to
update with an entry for clocks used by hwmod to have
clock name same as the alias.
Without this, the clk_get() in omap_hwmod would fail.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQblIiAAoJEIwa5zzehBx3J1EP/1pxMqjVKQDXxak+A6g8a7r0
hUTjqfiA9nZ4st+nk3PKJL9DNkoTEoZZqXghYRA+N6ej4hAaFJX1izgQDtjtjfRE
s2izZuxGka8Oiic6FpCUoQnMORg10tSLgyvlHNW4hXy3qpe2C4u1D2GJwA/GPeLQ
lHREekcJ3RKWutpG2hMtCT+9Bm4AwnnMY5uO39gxoXeMn6RoaACNIyYxz0NeL5bV
GDuawi7Pc4KJTXX+D/VU0o7VtksiUO8YBczFEra/9khSL/RI2PFalIX3DKiioqvA
yUA11d9proqojIdfdjVRPBHnIMl49H8ohBwbQfKnkNz9msl1BKN5PbakKls97mQ+
vaJpoACnc/3x4P/izEpwry5XqeIl5S5mwz4R4+fojpWpp4JPcly/cAKMAsXf5WRi
NF50E4D/8ysHE8WuBU5YHFgEEbn3nXkRbNMgdYtUwzixdmNJNaU8+33BJo34c4j0
DNktiEdKUBoiiEdsC1MgH86olD/sFNUxvXBub30hhOywoapgQE61fGQGxG38DV/K
kspTHz9SKUrmgbYEyMNOhz4paRrheYxx9cAgKP7Hp7m4Gu8d6ZqRqLqN9hbAbLuW
TbH2FpqcjSw4KnYYCepTixJ3dhGiICiILWHfsW3qCj5Le3YVwedCpBCL1/I+RqEP
kYTToVhur/T1yamHAmBi
=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
Pull media updates from Mauro Carvalho Chehab:
"The first part of the media updates for Kernel 3.7.
This series contain:
- A major tree renaming patch series: now, drivers are organized
internally by their used bus, instead of by V4L2 and/or DVB API,
providing a cleaner driver location for hybrid drivers that
implement both APIs, and allowing to cleanup the Kconfig items and
make them more intuitive for the end user;
- Media Kernel developers are typically very lazy with their duties
of keeping the MAINTAINERS entries for their drivers updated. As
now the tree is more organized, we're doing an effort to add/update
those entries for the drivers that aren't currently orphan;
- Several DVB USB drivers got moved to a new DVB USB v2 core; the new
core fixes several bugs (as the existing one that got bitroted).
Now, suspend/resume finally started to work fine (at least with
some devices - we should expect more work with regards to it);
- added multistream support for DVB-T2, and unified the API for
DVB-S2 and ISDB-S. Backward binary support is preserved;
- as usual, a few new drivers, some V4L2 core improvements and lots
of drivers improvements and fixes.
There are some points to notice on this series:
1) you should expect a trivial merge conflict on your tree, with the
removal of Documentation/feature-removal-schedule.txt: this series
would be adding two additional entries there. I opted to not
rebase it due to this recent change;
2) With regards to the PCTV 520e udev-related breakage, I opted to
fix it in a way that the patches can be backported to 3.5 even
without your firmware fix patch. This way, Greg doesn't need to
rush backporting your patch (as there are still the firmware cache
and firmware path customization issues to be addressed there).
I'll send later a patch (likely after the end of the merge window)
reverting the rest of the DRX-K async firmware request, fully
restoring its original behaviour to allow media drivers to
initialize everything serialized as before for 3.7 and upper.
3) I'm planning to work on this weekend to test the DMABUF patches
for V4L2. The patches are on my queue for several Kernel cycles,
but, up to now, there is/was no way to test the series locally.
I have some concerns about this particular changeset with regards
to security issues, and with regards to the replacement of the old
VIDIOC_OVERLAY ioctl's that is broken on modern systems, due to
GPU drivers change. The Overlay API allows direct PCI2PCI
transfers from a media capture card into the GPU framebuffer, but
its API is crappy. Also, the only existing X11 driver that
implements it requires a XV extension that is not available
anymore on modern drivers. The DMABUF can do the same thing, but
with it is promising to be a properly-designed API. If I can
successfully test this series and be happy with it, I should be
asking you to pull them next week."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (717 commits)
em28xx: regression fix: use DRX-K sync firmware requests on em28xx
drxk: allow loading firmware synchrousnously
em28xx: Make all em28xx extensions to be initialized asynchronously
[media] tda18271: properly report read errors in tda18271_get_id
[media] tda18271: delay IR & RF calibration until init() if delay_cal is set
[media] MAINTAINERS: add Michael Krufky as tda827x maintainer
[media] MAINTAINERS: add Michael Krufky as tda8290 maintainer
[media] MAINTAINERS: add Michael Krufky as cxusb maintainer
[media] MAINTAINERS: add Michael Krufky as lg2160 maintainer
[media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer
[media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer
[media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer
[media] MAINTAINERS: add Michael Krufky as tda18271 maintainer
[media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap
[media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()
[media] exynos-gsc: Add missing static storage class specifiers
[media] exynos-gsc: Remove <linux/version.h> header file inclusion
[media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()
[media] s5p-tv: Fix potential NULL pointer dereference error
[media] s5k6aa: Fix possible NULL pointer dereference
...
Merge misc patches from Andrew Morton:
"The MM tree is rather stuck while I wait to find out what the heck is
happening with sched/numa. Probably I'll need to route around all the
code which was added to -next, sigh.
So this is "everything else", or at least most of it - other small
bits are still awaiting resolutions of various kinds."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
lib/decompress.c add __init to decompress_method and data
kernel/resource.c: fix stack overflow in __reserve_region_with_split()
omfs: convert to use beXX_add_cpu()
taskstats: cgroupstats_user_cmd() may leak on error
aoe: update aoe-internal version number to 50
aoe: update documentation to better reflect aoe-plus-udev usage
aoe: remove unused code
aoe: make dynamic block minor numbers the default
aoe: update and specify AoE address guards and error messages
aoe: retain static block device numbers for backwards compatibility
aoe: support more AoE addresses with dynamic block device minor numbers
aoe: update documentation with new URL and VM settings reference
aoe: update copyright year in touched files
aoe: update internal version number to 49
aoe: remove unused code and add cosmetic improvements
aoe: increase net_device reference count while using it
aoe: associate frames with the AoE storage target
aoe: disallow unsupported AoE minor addresses
aoe: do revalidation steps in order
aoe: failover remote interface based on aoe_deadsecs parameter
...
Merge in the late Kirkwood branch with the OMAP late branch for upstream
submission.
Final contents described in shared tag.
Fixup remove/change conflicts in arch/arm/mach-omap2/devices.c and
drivers/spi/spi-omap2-mcspi.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
In case of error, the function voltdm_lookup() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case of error, the function voltdm_lookup() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case of error, the function omap_device_get_by_hwmod_name()
returns ERR_PTR() not NULL pointer. The NULL test in the return
value check should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
Vaibhav Hiremath