Add PIO mode support in receive and transmit path with RX interrupt
trigger of 16 bytes for Tegra194 and older chips.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-13-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Standard UART controllers support +/-4% baud rate error tolerance.
Tegra186 only supports 0% to +4% error tolerance whereas other Tegra
chips support standard +/-4% rate. Add chip data for knowing error
tolerance level for each soc. Creating new compatible for Tegra194
chip as it supports baud rate error tolerance of -2 to +2%, different
from older chips.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-12-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to adjust baud rates to fall under supported tolerance
range through DT.
Tegra186 chip has a hardware issue resulting in frame errors when
tolerance level for baud rate is negative. Provided entries to adjust
baud rate to be within acceptable range and work with devices that
can send negative baud rate. Also report error when baud rate set is
out of tolerance range of controller updated in device tree.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-11-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set maximum number of UART ports to 8 as older chips have 5 ports and
Tergra186 and later chips will have 8 ports. Add this info to chip
data. Read device tree compatible of this driver and register uart
driver with max ports of matching chip data.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-8-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chips prior to Tegra186 needed delay of 3 UART clock cycles to avoid
data loss. This issue is fixed in Tegra186 and a new flag is added to
check if FIFO mode is enabled. chip data updated to check if this flag
is available for a chip. Tegra186 has new compatible to enable this
flag.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-7-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Report overrun/parity/frame/break errors to top tty layer. Add support
to ignore break character if IGNBRK is set.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-5-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FIFO reset/flush code implemented now does not follow programming
guidelines. RTS line has to be turned off while flushing FIFOs to
avoid new transfers. Also check LSR bits UART_LSR_TEMT and UART_LSR_DR
to confirm FIFOs are flushed.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-4-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids two race conditions from the UART shutdown sequence both
leading to 'Machine check error in AXI2APB' and kernel oops.
One was that the clock was disabled before the DMA was terminated making
it possible for the DMA callbacks to be called after the clock was
disabled. These callbacks could write to the UART registers causing
timeout.
The second was that the clock was disabled before the UART was
completely flagged as closed. This is done after the shutdown is called
and a new write could be started after the clock was disabled.
tegra_uart_start_pio_tx could be called causing timeout.
Given that the baud rate is reset at the end of shutdown sequence, this
fix is to examine the baud rate to avoid register access from both race
conditions.
Besides, terminate the DMA before disabling the clock.
Signed-off-by: Ahung Cheng <ahcheng@nvidia.com>
Signed-off-by: Shardar Mohammed <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-3-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support to ignore read characters if CREAD flag is not set.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/1567572187-29820-2-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IER and DLH registers occupy the same address space, selected by
the LCR.DLAB bit. Hence, add port lock to protect IER when LCR.DLAB bit
is set.
Signed-off-by: Ahung Cheng <ahcheng@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1565609303-27000-5-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the internal loopback functionality that can be enabled with
TIOCM_LOOP.
Signed-off-by: Andreas Abel <aabel@nvidia.com>
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1565609303-27000-2-git-send-email-kyarlagadda@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-45-swboyd@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a few spelling mistakes I stumbled upon while debugging a customers
UART issues.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq can fail, so we should handle negative value when
returned.
[v2]
platform_get_irq can actually return zero on some platforms. So do not
remove checks for irq == 0 there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local mcr variable is never used in the tegra_uart_set_mctrl()
function, so it should be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the tegra UART driver there are three places where the RX DMA buffer
is handled and pushed up to the tty layer. In all three instances the
same functions are called and so instead of duplicating the code in three
places, move this code to a new helper function and use this new function.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial-tegra driver always uses DMA and hence the driver always
allocates DMA channels. Therefore, the test to see if the RX DMA channel
is initialised in tegra_uart_stop_rx() is unnecessary and so remove
the test and the code that corresponds to the case where the RX DMA
channel is not initialised. Please note that the call to
tegra_uart_stop_rx() should always be before the call to
tegra_uart_shutdown() which will uninitialise the RX DMA channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions in the serial-tegra driver have unnecessary return
statements at the end of a void function and so remove them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 853a699739 ("serial: tegra: handle race condition on uart rx
side") attempted to fix a race condition between the RX end of
transmission interrupt and RX DMA completion callback. Despite this
fix there is still another case where these two paths can race and
result in duplicated data. The race condition is as follows:
1. DMA completion interrupt occurs and schedules tasklet to call DMA
callback.
2. DMA callback for the UART driver starts to execute. This will copy
the data from the DMA buffer and restart the DMA. This is done under
uart port spinlock.
3. During the callback, UART interrupt is raised for end of receive. The
UART ISR runs and waits to acquire port spinlock held by the DMA
callback.
4. DMA callback gives up spinlock after copying the data, but before
restarting DMA.
5. UART ISR acquires the spin lock and reads the same DMA buffer because
DMA has not been restarted yet.
The release of the spinlock during the DMA callback was introduced by
commit 9b88748b36 ("tty: serial: tegra: drop uart_port->lock before
calling tty_flip_buffer_push()") to fix a spinlock lock-up issue when
calling tty_flip_buffer_push(). However, since then commit a9c3f68f3c
("tty: Fix low_latency BUG") migrated tty_flip_buffer_push() to always
use a workqueue, allowing tty_flip_buffer_push() to be called from
within atomic sections. Therefore, we can remove the unlocking of the
spinlock from the DMA callback and UART ISR and this will ensure that
the race condition no longer occurs.
Reported-by: Christopher Freeman <cfreeman@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to dmaengine_slave_config() fails, then the DMA buffer will
not be freed/unmapped. Fix this by moving the code that stores the
address of the buffer in the tegra_uart_port structure to before the
call to dmaengine_slave_config().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function tegra_uart_dma_channel_allocate() does not check that
dma_map_single() mapped the DMA buffer correctly. Add a check for this
and appropriate error handling.
Furthermore, if dmaengine_slave_config() (called by
tegra_uart_dma_channel_allocate()) fails, then memory allocated/mapped
is not freed/unmapped. Therefore, call tegra_uart_dma_channel_free()
instead of just dma_release_channel() if dmaengine_slave_config() fails.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two issues in the shutdown path of the UARTs which are:
1. The function tegra_uart_shutdown() calls tegra_uart_flush_buffer()
to stop DMA TX transfers. However, tegra_uart_flush_buffer() is
called after the DMA channels have already been freed and so actually
does nothing.
2. The function that frees the DMA channels
(tegra_uart_dma_channel_free()), unmaps the dma buffer before
freeing the DMA channel and does not ensure the DMA has been
stopped.
Resolve this by fixing the code in tegra_uart_dma_channel_free() to
ensure the DMA is stopped, free the DMA channel and then unmap the DMA
buffer. Finally, remove the unnecessary call to tegra_uart_flush_buffer().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA cookie for the RX channel is being used by the TX channel.
Therefore, fix driver to use the correct DMA cookie for the TX channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_insert_flip_string() takes an argument "size" which is
of type size_t. This is an unsigned type. Update the count,
rx_bytes_requested and tx_bytes_requested in the tegra serial driver to
be unsigned integers so that an unsigned type is passed to
tty_insert_flip_string().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra serial driver has two paths through which receive data is
copied up to the tty layer. These are:
1. DMA completion callback
2. UART RX interrupt
A UART RX interrupt occurs for either RX_TIMEOUT (data has been sitting
in the Rx FIFO for more than 4 character times without being read
because there is not enough data to reach the trigger level), End of
Receive Data event (receiver detects that data stops coming in for more
than 4 character times) or a receive error.
In the RX interrupt path, the following happens ...
- All RX DMA transfers are stopped
- Any data in the DMA buffer and RX FIFO are copied up to the tty layer.
- DMA is restarted/primed for the RX path
In the DMA completion callback, the DMA buffer is copied up to the tty
layer but there is no check to see if the RX interrupt could have
occurred between the DMA interrupt firing the the DMA callback running.
Hence, if a RX interrupt was to occur shortly after the DMA completion
interrupt, it is possible that the RX interrupt path has already copied
the DMA buffer before the DMA callback has been called. Therefore, when
the DMA callback is called, if the DMA is already in-progress, then this
indicates that the UART RX interrupt has already occurred and there is
nothing to do in the DMA callback. This race condition can cause
duplicated data to be received.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
[jonathanh@nvidia.com: Moved async_tx_ack() call to after check to see
if DMA has completed because if the DMA is in progress we do not need
to ACK yet. Changed the print from dev_info to dev_debug. Updated
changelog to add more commentary on the race condition based upon
feedback from author.]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is only necessary to read data from the dma buffer when the count
value is non-zero and hence, tegra_uart_copy_rx_to_tty() so only be
called when this is the case.
Although, this was being tested for in two places, there is a third
place where this was not tested. However, instead of adding another
if-statement prior to calling tegra_uart_copy_rx_to_tty(), move the test
inside the function.
Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
[jonathanh@nvidia.com: Re-worked patch to move the check for the count
value inside the function tegra_uart_copy_rx_to_tty(). Updated
changelog with more commentary.]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For all tegra devices (up to t210), there is a hardware issue that
requires software to wait for 3 UART clock periods after enabling
the TX fifo, otherwise data could be lost.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For all tegra devices (up to t210), there is a hardware issue that
requires software to wait for 32 UART clock periods for the flush
to propagate otherwise TX data could be post. Add a helper function
to wait for N UART clock periods and update delay following FIFO
flush to be 32 UART clock cycles.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty break and error flags are not bit masks so do not to use bitwise
OR when assigning them.
Note that there is no functional change due to the if-else construct and
flag having been initialised to zero (TTY_NORMAL).
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the context of the final tty & port close, flushing the tx
ring buffer after the hardware has already been shutdown and
the ring buffer freed is neither required nor desirable.
uart_flush_buffer() performs 3 operations:
1. Resets tx ring buffer indices, but the tx ring buffer has
already been freed and the indices are reset if the port is
re-opened.
2. Calls uart driver's flush_buffer() method
5 in-tree uart drivers define flush_buffer() methods:
amba-pl011, atmel-serial, imx, serial-tegra, timbuart
These have been refactored into the shutdown() method, if
required.
3. Kicks the ldisc for more writing, but this is undesirable.
The file handle is being released; any waiting writer will
will be kicked out by tty_release() with a warning. Further,
the N_TTY ldisc may generate SIGIO for a file handle which
is no longer valid.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Rx dma descriptor allocated without the DMA_ACK flags so that
once after tarnsfer done or terminated, client can ack the descriptor
to free it for later use.
If the Rx DMA is terminated for some reason then rx-dma descriptor
is not getting acked which causes the memory leak and list of usage
desc to grow continuously.
Hence, acknowledge the rx-dma descriptor once transfer is terminated
to avoid memory leak and desc list to grow.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When channel is require to stop transmit then update the Tx circular
buffer only when DMA based transfer is in progress. If there is no
DMA based transfer then no need to update the Tx buffer.
Signed-off-by: Pradeep Goudagunta <pgoudagunta@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By using dma_request_slave_channel_or_err(), the DMA slave ID can be
looked up from standard DT properties, and squirrelled away during
channel allocation. Hence, there's no need to use a custom DT property
to store the slave ID.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'cons' is a pointer; thus NULL should be used instead of 0.
Also, local symbols are staticized.
Fix the following sparse warnings:
drivers/tty/serial/serial-tegra.c:1209:27: warning: Using plain integer as NULL pointer
drivers/tty/serial/serial-tegra.c:1240:29: warning: symbol 'tegra20_uart_chip_data' was not declared. Should it be static?
drivers/tty/serial/serial-tegra.c:1246:29: warning: symbol 'tegra30_uart_chip_data' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra only supports, and always enables, device tree. Remove all ifdefs
for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many of the tty functions were converted to use a struct tty_port
instead of a struct tty_struct. Update the Tegra driver accordingly to
avoid build breakage.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA's Tegra has multiple UART controller which supports:
- APB DMA based controller fifo read/write.
- End Of Data interrupt in incoming data to know whether end
of frame achieve or not.
- HW controlled RTS and CTS flow control to reduce SW overhead.
Add serial driver to use all above feature.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krishna Yarlagadda