Print the error number of GPIO hog failed during its configurations.
This helps in identifying the failure without instrumenting the code.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit ff2b135922 ("gpio: make the gpiochip a real device"),
attempts to add a gpio chip prior to gpiolib initialization cause
the system to crash. This happens because gpio_bus_type has not been
registered yet. Defer creating gpio devices until after gpiolib has
been initialized to fix the problem.
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is possible that a gpio chip is registered before the gpiolib
initialization code has run. This means we can not use devm_ functions
to allocate memory at that time. Do it the old fashioned way.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When firmware does not use _DSD properties that allow properly name GPIO
resources, the kernel falls back on parsing _CRS resources, and will
return entries described as GpioInt() as general purpose GPIOs even
though they are meant to be used simply as interrupt sources for the
device:
Device (ETSA)
{
Name (_HID, "ELAN0001")
...
Method(_CRS, 0x0, NotSerialized)
{
Name(BUF0,ResourceTemplate ()
{
I2CSerialBus(
0x10, /* SlaveAddress */
ControllerInitiated, /* SlaveMode */
400000, /* ConnectionSpeed */
AddressingMode7Bit, /* AddressingMode */
"\\_SB.I2C1", /* ResourceSource */
)
GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone,,
"\\_SB.GPSW") { BOARD_TOUCH_GPIO_INDEX }
} )
Return (BUF0)
}
...
}
This gives troubles with drivers such as Elan Touchscreen driver
(elants_i2c) that uses devm_gpiod_get to look up "reset" GPIO line and
decide whether the driver is responsible for powering up and resetting
the device, or firmware is. In the above case the lookup succeeds, we
map GPIO as output and later fail to request client->irq interrupt that
is mapped to the same GPIO.
Let's ignore resources described as GpioInt() while parsing _CRS when
requesting output GPIOs (but allow them when requesting GPIOD_ASIS or
GPIOD_IN as some drivers, such as i2c-hid, do request GPIO as input and
then map it to interrupt with gpiod_to_irq).
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO controllers has a special hardware bit we can flip
to support open drain / source. This means that on these hardwares
we do not need to emulate OD/OS by setting the line to input
instead of actively driving it high/low. Add an optional vtable
callback to the driver set_single_ended() so that driver can
implement this in hardware if they have it.
We may need a pinctrl_gpio_set_config() call at some point to
propagate this down to a backing pin control device on systems
with split GPIO/pin control.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original code of gpiodev_add_to_list is not very clear which
lead to bugs or compiling warning, reference the following patches:
Bugs:
1. Commit ef7c755303 ("gpiolib: improve overlap check of range of
gpio").
2. Commit 96098df125 ("gpiolib: fix chip order in gpio list")
Warning:
1. Commit e28ecca6ea ("gpio: fix warning about iterator").
of gpio").
There is a off-list discussion about how to improve it consequently.
This commit try to follow this by rewriting the whole functions.
Tested pass with my gpio mockup driver and test scripts[1].
[1] http://www.spinics.net/lists/linux-gpio/msg09598.html
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I named the field representing the current user of GPIO line as
"label" but this is too vague and ambiguous. Before anyone gets
confused, rename it to "consumer" and indicate clearly in the
documentation that this is a string set by the user of the line.
Also clean up leftovers in the documentation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add device managed APIs devm_gpiochip_add_data() and
devm_gpiochip_remove() for the APIs gpiochip_add_data()
and gpiochip_remove().
This helps in reducing code in error path and sometimes
removal of .remove callback for driver unbind.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
This fixes the wrongly indicated lines in the userspace
ABI: test for the right BITS, do not treat bit numbers as
bitmasks.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a GPIO line ABI for getting name, label and a few select
flags from the kernel.
This hides the kernel internals and only tells userspace what it
may need to know: the different in-kernel consumers are masked
behind the flag "kernel" and that is all userspace needs to know.
However electric characteristics like active low, open drain etc
are reflected to userspace, as this is important information.
We provide information on all lines on all chips, later on we will
likely add a flag for the chardev consumer so we can filter and
display only the lines userspace actually uses in e.g. lsgpio,
but then we first need an ABI for userspace to grab and use
(get/set/select direction) a GPIO line.
Sample output from "lsgpio" on ux500:
GPIO chip: gpiochip7, "8011e000.gpio", 32 GPIO lines
line 0: unnamed unlabeled
line 1: unnamed unlabeled
(...)
line 25: unnamed "SFH7741 Proximity Sensor" [kernel output open-drain]
line 26: unnamed unlabeled
(...)
Tested-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio_chip label is useful for userspace to understand what
kind of GPIO chip it is dealing with. Let's store a copy of this
label in the gpio_device, add it to the struct passed to userspace
for GPIO_GET_CHIPINFO_IOCTL and modify lsgpio to show it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The use of kmalloc() to allocate the gpio_device leaves the contained struct
device object in an unknown state. Calling dev_set_name() on a struct device
of unknown state can trigger the free() of an invalid pointer, as seen in the
following backtrace (collected by Tony Lindgren):
kfree
kobject_set_name_vargs
dev_set_name
gpiochip_add_data
omap_gpio_probe
platform_drv_probe
...
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Michael Welling <mwelling@ieee.org>
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Michael Welling <mwelling@ieee.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
My left hand merges code to privatize the descriptor handling
while my right hand merges drivers that poke around and
disrespect with the same gpiolib internals.
So let's expose the proper APIs for drivers to ask the gpiolib
core if a line is marked as open drain or open source and
get some order around things so this driver compiles again.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We move to manage this pointer under gpiolib control rather than
leave it in the subdevice's gpio_chip. We can not NULL it after
gpiochip_remove so at to keep things tight.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of keeping this reference to the pin ranges in the
client driver-supplied gpio_chip, move it to the internal
gpio_device as the drivers have no need to inspect this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Every time a descriptor is retrieved from the gpiolib, we issue
module_get() to reference count the module supplying the GPIOs.
We also need to call device_get() and device_put() as we also
reference the backing gpio_device when doing this.
Since the sysfs GPIO interface is using gpiod_get() this will
also reference count the sysfs requests until all GPIOs are
unexported.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some information about the GPIO chip need to stay around also
after the gpio_chip has been removed and only the gpio_device
persist. The base and ngpio are such things, for example we
don't want a new chip arriving to overlap the number space
of a dangling gpio_device, and the chardev may still query
the device for the number of lines etc.
Note that the code that assigns base and insert gpio_device
into the global list no longer check for a missing gpio_chip:
we respect the number space allocated by any other gpio_device.
As a consequence of the gdev being referenced directly from
the gpio_desc, we need to verify it differently from all
in-kernel API calls that fall through to direct queries to
the gpio_chip vtable: we first check that desc is !NULL, then
that desc->gdev is !NULL, then, if desc->gdev->chip is NULL,
we *BAIL OUT* without any error, so as to manage the case
where operations are requested on a device that is gone.
These checks were non-uniform and partly missing in the past:
so to simplify: create the macros VALIDATE_DESC() that will
return -EINVAL if the desc or desc->gdev is missing and just
0 if the chip is gone, and conversely VALIDATE_DESC_VOID()
for the case where the function does not return an error.
By using these macros, we get warning messages about missing
gdev with reference to the right function in the kernel log.
Despite the macro business this simplifies the code and make
it more readable than if we copy/paste the same descriptor
checking code into all code ABI call sites (IMHO).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This kind of hacks disturbs the refactoring of the gpiolib.
The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need gpio_device to hold the descriptors so that they can
be lifecycled with the struct gpio_device held from userspace.
Move the descriptor array into gpio_device. Also rename it from
"desc" (singularis) to "descs" (pluralis) to reflect the fact
that it is an array.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since gpio_device is the struct that survives if the backing
gpio_chip is removed, move the sysfs mock device to this state
container so it becomes part of the dangling state of the
GPIO device on removal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the device core reference count for the device goes to
0 and it calls .release() we free resources and so can also
finally free up the GPIO state container, struct gpio_device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A new chardev that is to be used for userspace GPIO access is
added in this patch. It is intended to gradually replace the
horribly broken sysfs ABI.
Using a chardev has many upsides:
- All operations are per-gpiochip, which is the actual
device underlying the GPIOs, making us tie in to the
kernel device model properly.
- Hotpluggable GPIO controllers can come and go, as this
kind of problem has been know to userspace for character
devices since ages, and if a gpiochip handle is held in
userspace we know we will break something, whereas the
sysfs is stateless.
- The one-value-per-file rule of sysfs is really hard to
maintain when you want to twist more than one knob at a time,
for example have in-kernel APIs to switch several GPIO
lines at the same time, and this will be possible to do
with a single ioctl() from userspace, saving a lot of
context switching.
We also need to add a new bus type for GPIO. This is
necessary for example for userspace coldplug, where sysfs is
traversed to find the boot-time device nodes and create the
character devices in /dev.
This new chardev ABI is *non* *optional* and can be counted
on to be present in the future, emphasizing the preference
of this ABI.
The ABI only implements one single ioctl() to get the name
and number of GPIO lines of a chip. Even this is debatable:
see it as a minimal example for review. This ABI shall be
ruthlessly reviewed and etched in stone.
The old /sys/class/gpio is still optional to compile in,
but will be deprecated.
Unique device IDs are created using IDR, which is overkill
and insanely scalable, but also well tested.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use the new struct device inside gpio_chip to related debug
prints and warnings, and we also add it to the debugfs dump.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO chips have been around for years, but were never real devices,
instead they were piggy-backing on a parent device (such as a
platform_device or amba_device) but this was always optional.
GPIO chips could also exist without any device at all, with its
struct device *parent (ex *dev) pointer being set to null.
When sysfs was in use, a mock device would be created, with the
optional parent assigned, or just floating orphaned with NULL
as parent.
If sysfs is active, it will use this device as parent.
We now create a gpio_device struct containing a real
struct device and move the subsystem over to using that. The
list of struct gpio_chip:s is augmented to hold struct
gpio_device:s and we find gpio_chips:s by first looking up
the struct gpio_device.
The struct gpio_device is designed to stay around even if the
gpio_chip is removed, so as to satisfy users in userspace
that need a backing data structure to hold the state of the
session initiated with e.g. a character device even if there is
no physical chip anymore.
From this point on, gpiochips are devices.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull input updates from Dmitry Torokhov:
- new driver for eGalaxTouch serial touchscreen
- new driver for TS-4800 touchscreen
- an update for Goodix touchscreen driver
- PS/2 mouse module was reworked to limit number of protocols we try on
pass-through ports to speed up their detection time
- wacom_w8001 touchscreen driver now reports pen and touch via separate
instances of input devices
- other driver changes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (42 commits)
Input: elantech - mark protocols v2 and v3 as semi-mt
Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE
Input: gpio-keys - fix check for disabling unsupported keys
Input: omap-keypad - remove dead check
Input: ti_am335x_tsc - fix HWPEN interrupt handling
Input: omap-keypad - set tasklet data earlier
Input: rohm_bu21023 - fix handling of retrying firmware update
Input: ALPS - report v3 pinnacle trackstick device only if is present
Input: ALPS - detect trackstick presence for v7 protocol
Input: pcap_ts - use to_delayed_work
Input: bma150 - constify bma150_cfg structure
Input: i8042 - add Fujitsu Lifebook U745 to the nomux list
Input: egalax_ts_serial - fix potential NULL dereference on error
Input: uinput - sanity check on ff_effects_max and EV_FF
Input: uinput - rework ABS validation
Input: uinput - add new UINPUT_DEV_SETUP and UI_ABS_SETUP ioctl
Input: goodix - use "inverted_[xy]" flags instead of "rotated_screen"
Input: goodix - add axis swapping and axis inversion support
Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
Input: goodix - add power management support
...
In some situations the gpio_list order is not correct.
As a consequence gpiochip_find_base returns the same
base number twice. This happens when a first ship is added
with manual base number, then other ships are added using
automatic base number.
To prevent this behaviour, this patch add the new chip after
the last element of the gpio list.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a void * pointer to gpio_chip so that driver can
assign and retrieve some states. This is done to get rid of
container_of() calls for gpio_chips embedded inside state
containers, so we can remove the need to have the gpio_chip
or later (planned) struct gpio_device be dynamically allocated
at registration time, so that its struct device can be properly
reference counted and not bound to its parent device (e.g.
a platform_device) but instead live on after unregistration
if it is opened by e.g. a char device or sysfs.
The data is added with the new function gpiochip_add_data()
and for compatibility we add static inline wrapper function
gpiochip_add() that will call gpiochip_add_data() with
NULL as argument. The latter will be removed once we have
exorcised gpiochip_add() from the kernel.
gpiochip_get_data() is added as a static inline accessor
for drivers to quickly get their data out.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO is used as an interrupt in ACPI, the irq_type was not
available for device driver.
Make available polarity and triggering information in acpi_find_gpio by
renaming acpi_gpio_info field active_low to polarity and adding triggering
field (edge/level).
For sanity, in gpiolib.c replace info.active_low by
"info.polarity == GPIO_ACTIVE_LOW".
Set the irq_type if necessary in acpi_dev_gpio_irq_get.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We were getting build warning about "iterator" being used uninitialized.
Use iterator properly to fix the build warning and in the process remove
the variable "pos" which is not required now.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 45ad7db90b.
We have fixed all the drivers that were returning ambious values
not clamped to [0,1] or an error code, so return the error
propagating behaviour of the API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit e20538b82f
("gpio: Propagate errors from chip->get()")
started to propagate errors from the .get() functions since
we can get errors from the infrastructure of e.g. slowbus
GPIO expanders.
However it turns out a bunch of drivers relied on the core
to clamp the value, so we need to revert to the old behaviour
and go over all drivers and fix them to conform to the
expectations of the core before we go back to propagating
the error code.
Cc: stable@vger.kernel.org # 4.3+
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Fixes: e20538b82f ("gpio: Propagate errors from chip->get()")
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should not fall back to the legacy unnamed gpio lookup style if the
driver requests gpios with different names, because we'll give out the same
gpio twice. Let's keep track of the names that were used for the device and
only do the fallback for the first name used.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit f4d566a8a0e6 ("gpio: change member .dev to .parent") changes
member of gpiochip from .dev to .parent. Update the corresponding
comment.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit c0017ed719 ("gpio: Introduce gpio descriptor 'name'") causes
OOPS on boot on LPC32xx boards:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0+ #707
Hardware name: LPC32XX SoC (Flattened Device Tree)
task: c381baa0 ti: c381e000 task.ti: c381e000
PC is at strcmp+0x10/0x40
LR is at gpiochip_add+0x3d0/0x4d4
pc : [<>] lr : [<>] psr: a0000093
sp : c381fd60 ip : c381fd70 fp : c381fd6c
[snip]
Backtrace:
[<>] (strcmp) from [<>] (gpiochip_add+0x3d0/0x4d4)
[<>] (gpiochip_add) from [<>] (lpc32xx_gpio_probe+0x44/0x60)
[<>] (lpc32xx_gpio_probe) from [<>] (platform_drv_probe+0x40/0x8c)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x110/0x294)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0xd4/0x1f0)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x38/0x4c)
[<>] (__platform_driver_register) from [<>] (lpc32xx_gpio_driver_init+0x18/0x20)
[<>] (lpc32xx_gpio_driver_init) from [<>] (do_one_initcall+0x108/0x1c8)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
This is caused by the fact that at the moment some GPIO names are set
to NULL, there is a hole in linear representation of one GPI bank, see
drivers/gpio/gpio-lpc32xx.c / gpi_p3_names[] for details.
The same problem most probably affects also gpio-cs5535.c, see
cs5535_gpio_names[].
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to check if number of gpio is positive if there is no
such check in devicetree or acpi or whatever called before
gpiochip_add.
I suppose that devicetree and acpi do not allow insert gpiochip
with zero number but I do not know if it is enough to ignore
this check in gpiochip_add.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are limitations for the current checker:
1. Could not check the overlap if the new gpiochip is the secondly
gpiochip.
2. Could not check the overlap if the new gpiochip is overlap
with the left of gpiochip. E.g. if we insert [c, d] between
[a,b] and [e, f], and e >= c + d, it will successful even if
c < a + b.
3. Allow overlap of base of different gpiochip.
This patch fix these issues by checking the overlap of both right and
left gpiochip in the same loop statement.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
[Tweaked to remove unnecessary ret variable]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit f881bab038 ("gpio: keep the GPIO line names internal")
change the error to warning in gpiochip_set_desc_names. Update the
comment accordingly.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should not fall back to the legacy unnamed gpio lookup style if the
driver requests gpios with different names, because we'll give out the same
gpio twice. Let's keep track of the names that were used for the device and
only do the fallback for the first name used.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface)
and a few fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2)
support along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated
by the specification) to avoid confusion on systems with more than
255 logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges
on x86 and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when
it has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume
handling in some cases and the changes include a couple of users
of it (the i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up
the system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that
code (Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common
cpufreq policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states
range to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization
to make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=1gaH
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Quite a new features are included this time.
First off, the Collaborative Processor Performance Control interface
(version 2) defined by ACPI will now be supported on ARM64 along with
a cpufreq frontend for CPU performance scaling.
Second, ACPI gets a new infrastructure for the early probing of IRQ
chips and clock sources (along the lines of the existing similar
mechanism for DT).
Next, the ACPI core and the generic device properties API will now
support a recently introduced hierarchical properties extension of the
_DSD (Device Specific Data) ACPI device configuration object. If the
ACPI platform firmware uses that extension to organize device
properties in a hierarchical way, the kernel will automatically handle
it and make those properties available to device drivers via the
generic device properties API.
It also will be possible to build the ACPICA's AML interpreter
debugger into the kernel now and use that to diagnose AML-related
problems more efficiently. In the future, this should make it
possible to single-step AML execution and do similar things.
Interesting stuff, although somewhat experimental at this point.
Finally, the PM core gets a new mechanism that can be used by device
drivers to distinguish between suspend-to-RAM (based on platform
firmware support) and suspend-to-idle (or other variants of system
suspend the platform firmware is not involved in) and possibly
optimize their device suspend/resume handling accordingly.
In addition to that, some existing features are re-organized quite
substantially.
First, the ACPI-based handling of PCI host bridges on x86 and ia64 is
unified and the common code goes into the ACPI core (so as to reduce
code duplication and eliminate non-essential differences between the
two architectures in that area).
Second, the Operating Performance Points (OPP) framework is
reorganized to make the code easier to find and follow.
Next, the cpufreq core's sysfs interface is reorganized to get rid of
the "primary CPU" concept for configurations in which the same
performance scaling settings are shared between multiple CPUs.
Finally, some interfaces that aren't necessary any more are dropped
from the generic power domains framework.
On top of the above we have some minor extensions, cleanups and bug
fixes in multiple places, as usual.
Specifics:
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface) and a few
fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2) support
along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated by
the specification) to avoid confusion on systems with more than 255
logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges on x86
and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when it
has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume handling
in some cases and the changes include a couple of users of it (the
i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up the
system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that code
(Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common cpufreq
policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states range
to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization to
make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes)"
* tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (108 commits)
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
PM / Domains: Merge measurements for PM QoS device latencies
PM / Domains: Don't measure ->start|stop() latency in system PM callbacks
PM / clk: Fix broken build due to non-matching code and header #ifdefs
ACPI / Documentation: add copy_dsdt to ACPI format options
ACPI / sysfs: correctly check failing memory allocation
ACPI / video: Add a quirk to force native backlight on Lenovo IdeaPad S405
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI / PAD: power_saving_thread() is not freezable
ACPI / PM: Fix incorrect wakeup IRQ setting during suspend-to-idle
ACPI: Using correct irq when waiting for events
ACPI: Use correct IRQ when uninstalling ACPI interrupt handler
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
...
The flag matches the DT GPIO_SINGLE_ENDED flag and allows drivers to
parse and use the DT flag to handle single-ended (open-drain or
open-source) GPIOs.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When requesting a GPIO through the legacy or the gpiod_* API the
gpiochip request operation is first called and then the GPIO flags are
parsed and the GPIO is configured. This prevents the gpiochip from
rejecting the request if the flags are not supported by the device.
To fix this split the parse-and-configure operation in two and parse
flags before requesting the GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide generic request/free implementations that pinctrl aware gpio
drivers can use instead of open coding if they use a 1:1 pin to gpio
signal mapping.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The parameter offset is an unsigned, so it makes no sense to compare
it for >= 0. Fix the compiler warning regarding this by removing this
comparison.
As the macro GPIO_OFFSET_VALID is only used at this single place, simplify
the code by dropping the macro completely and dropping the invert, too.
No functional change.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This refactors the changes to the GPIO line naming mechanism to
not have so widespread effects, instead we conclude the patch series
by having created a name attribute in the GPIO descriptor, that need
not be globally unique, and it will be initialized from the old
.names array in struct gpio_chip if it exists, then used in the legacy
sysfs code like the array was used previously.
The associated changes to name lines from the device tree are
controversial and need to stand alone from this. Resulting changes:
1. Remove the export and the header for the gpio_name_to_desc() as so
far the only use is inside gpiolib.c. Staticize gpio_name_to_desc()
and move it above the only function using it.
2. Only print a warning if there are two GPIO lines with the same name.
The reason is to preserve current behaviour: before the previous
changes to the naming mechanism this would not reject probing the
driver, instead the error would occur when trying to export the line
in sysfs, so restore this behaviour, but print a friendly warning
if names collide.
Cc: Johan Hovold <johan@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add some information about gpio names to the debugfs gpio file. name and
label of a GPIO are then displayed next to each other. This way it is
easy to see what the real name of GPIO is and what the driver requested
it for.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[Dropped unsolicited sysfs ABI patch hunk]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds GPIO names to the GPIO descriptors when initializing the
gpiochip. It also introduces a check whether any of the new names will
conflict with an existing GPIO name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The latest gpio hogging mechanism assigns each gpio a 'line-name' in the
devicetree. The 'name' field is different from the 'label' field.
'label' is only used for requested GPIOs to describe its current use by
driver or userspace.
The 'name' field describes the GPIO itself, not the use. This is most
likely identical to the label in the schematic on the GPIO line and
should help to find this particular GPIO.
This is equivalent to the gpiochip->names array. However names should be
stored in the GPIO descriptor. We will use gpiochip->names in the future
only as initializer for the GPIO descriptors for drivers that assign
GPIO names hardcoded. All other GPIO names will be parsed from DT and
directly assigned to the GPIO descriptor.
This patch adds a helper function to find gpio descriptors by name
instead of gpio number.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make device_get_next_child_node() work with ACPI data-only subnodes
introduced previously.
Namely, replace acpi_get_next_child() with acpi_get_next_subnode()
that can handle (and return) child device objects as well as child
data-only subnodes of the given device and modify the ACPI part
of the GPIO subsystem to handle data-only subnodes returned by it.
To that end, introduce acpi_node_get_gpiod() taking a struct
fwnode_handle pointer as the first argument. That argument may
point to an ACPI device object as well as to a data-only subnode
and the function should do the right thing (ie. look for the matching
GPIO descriptor correctly) in either case.
Next, modify fwnode_get_named_gpiod() to use acpi_node_get_gpiod()
instead of acpi_get_gpiod_by_index() which automatically causes
devm_get_gpiod_from_child() to work with ACPI data-only subnodes
that may be returned by device_get_next_child_node() which in turn
is required by the users of that function (the gpio_keys_polled
and gpio-leds drivers).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Modify is_acpi_node() to return "true" for ACPI data-only subnodes as
well as for ACPI device objects and change the name of to_acpi_node()
to to_acpi_device_node() so it is clear that it covers ACPI device
objects only. Accordingly, introduce to_acpi_data_node() to cover
data-only subnodes in an analogous way.
With that, make the fwnode_property_* family of functions work with
ACPI data-only subnodes introduced previously.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It's possible to have gpio chips hanging off unreliable remote buses
where the get() operation will fail to acquire a readout of the current
gpio state. Propagate these errors to the consumer so that they can
act on, retry or ignore these failing reads, instead of treating them as
the line being held high.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm for 4.3. Nouveau is
probably the biggest amount of changes in here, since it missed 4.2.
Highlights below, along with the usual bunch of fixes.
All stuff outside drm should have applicable acks.
Highlights:
- new drivers:
freescale dcu kms driver
- core:
more atomic fixes
disable some dri1 interfaces on kms drivers
drop fb panic handling, this was just getting more broken, as more locking was required.
new core fbdev Kconfig support - instead of each driver enable/disabling it
struct_mutex cleanups
- panel:
more new panels
cleanup Kconfig
- i915:
Skylake support enabled by default
legacy modesetting using atomic infrastructure
Skylake fixes
GEN9 workarounds
- amdgpu:
Fiji support
CGS support for amdgpu
Initial GPU scheduler - off by default
Lots of bug fixes and optimisations.
- radeon:
DP fixes
misc fixes
- amdkfd:
Add Carrizo support for amdkfd using amdgpu.
- nouveau:
long pending cleanup to complete driver,
fully bisectable which makes it larger,
perfmon work
more reclocking improvements
maxwell displayport fixes
- vmwgfx:
new DX device support, supports OpenGL 3.3
screen targets support
- mgag200:
G200eW support
G200e new revision support
- msm:
dragonboard 410c support, msm8x94 support, msm8x74v1 support
yuv format support
dma plane support
mdp5 rotation
initial hdcp
- sti:
atomic support
- exynos:
lots of cleanups
atomic modesetting/pageflipping support
render node support
- tegra:
tegra210 support (dc, dsi, dp/hdmi)
dpms with atomic modesetting support
- atmel:
support for 3 more atmel SoCs
new input formats, PRIME support.
- dwhdmi:
preparing to add audio support
- rockchip:
yuv plane support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1369 commits)
drm/amdgpu: rename gmc_v8_0_init_compute_vmid
drm/amdgpu: fix vce3 instance handling
drm/amdgpu: remove ib test for the second VCE Ring
drm/amdgpu: properly enable VM fault interrupts
drm/amdgpu: fix warning in scheduler
drm/amdgpu: fix buffer placement under memory pressure
drm/amdgpu/cz: fix cz_dpm_update_low_memory_pstate logic
drm/amdgpu: fix typo in dce11 watermark setup
drm/amdgpu: fix typo in dce10 watermark setup
drm/amdgpu: use top down allocation for non-CPU accessible vram
drm/amdgpu: be explicit about cpu vram access for driver BOs (v2)
drm/amdgpu: set MEC doorbell range for Fiji
drm/amdgpu: implement burst NOP for SDMA
drm/amdgpu: add insert_nop ring func and default implementation
drm/amdgpu: add amdgpu_get_sdma_instance helper function
drm/amdgpu: add AMDGPU_MAX_SDMA_INSTANCES
drm/amdgpu: add burst_nop flag for sdma
drm/amdgpu: add count field for the SDMA NOP packet v2
drm/amdgpu: use PT for VM sync on unmap
drm/amdgpu: make wait_event uninterruptible in push_job
...
Since IRQ chip helpers were introduced drivers lose ability to
register separate lockdep classes for each registered GPIO IRQ
chip and the gpiolib now is using shared lockdep class for
all GPIO IRQ chips (gpiochip_irq_lock_class).
As result, lockdep will produce warning when there are min two
stacked GPIO chips and all of them are interrupt controllers.
HW configuration which generates lockdep warning (TI dra7-evm):
[SOC GPIO bankA.gpioX]
<- irq - [pcf875x.gpioY]
<- irq - DevZ.enable_irq_wake(pcf_gpioY_irq);
The issue was reported in [1] and discussed [2].
=============================================
[ INFO: possible recursive locking detected ]
4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted
---------------------------------------------
sh/63 is trying to acquire lock:
(class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
but task is already holding lock:
(class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(class);
lock(class);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by sh/63:
#0: (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164
#1: (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0
#2: (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0
#3: (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4
#4: (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398
#5: (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94
#6: (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94
stack backtrace:
CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14)
[<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c)
[<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20)
[<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128)
[<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c)
[<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94)
[<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc)
[<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54)
[<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc)
[<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4)
[<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124)
[<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398)
[<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4)
[<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728)
[<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4)
[<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8)
[<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0)
[<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8)
[<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164)
[<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c)
[<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54)
Lets fix it by using separate lockdep class for each registered GPIO
IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros.
The implementation of this patch inspired by solution done by Nicolas
Boichat for regmap [3]
[1] http://www.spinics.net/lists/linux-gpio/msg05844.html
[2] http://www.spinics.net/lists/linux-gpio/msg06021.html
[3] http://www.spinics.net/lists/arm-kernel/msg429834.html
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Roger Quadros <rogerq@ti.com>
Tested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the driver has specified its own irq_{request/release}_resources()
functions, don't override them. The gpio-etraxfs driver will use this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
[Added a small comment blurb]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER if
the pin controller isn't available.
Otherwise, the GPIO range wouldn't be set at all unless the pin
controller probed always before the GPIO chip.
With this change, the probe of the GPIO chip will be deferred and will
be retried at a later point, hopefully once the pin controller has been
registered and probed already.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed as most platforms don't use probing.
There appears to be a great deal of blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This variable is used as an iterator and initialized in the
list_for_each() loop.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case we unload and load a driver module again that is registering a
lookup table, without this it will result in multiple entries. Provide
an option to remove the lookup table on driver unload
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gpiod_get* functions mandatory and so allows to remove an ugly cpp hack
introduced in commit 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) for v3.17-rc1.
The other nine commits fix the last remaining users of these functions that
don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the
gpiod functions needs fixing anyhow.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVmj+OAAoJEMH8FHityuwJHGcH/A5bSLcdaFCMcrYceYD/odzR
X/mer/CcW/uWG0sUha2pZjT172szSrm0/Bk+SaY5Ub0c6ssCpKRGhtqZNVWWz44V
duRQGkYEFODHSed1XnKQyKwr6nLyhjmj8RuP5GokjcsBZyl4onj+NHgmpH5aQBYC
4NyFpIXcSS4jCwj4nsZu4Y2xLAgu/t5oVzqDheqTyZ9imgaR8hbyminKhN+wFfrI
FKukShQ5AQPVs7pGEqeY0wgJp+keOIYLukLwvgZw+S7MxixXaPiSK1Ez9DPY9CFo
f+NkDV6GIe4OAOGFsL9dCxR0sO6mF7C5PpYuDUBtISi3JHNAvW+Ri7FKPeSDikA=
=ixJj
-----END PGP SIGNATURE-----
Merge tag 'gpiod-flags-for-4.3' of git://git.pengutronix.de/git/ukl/linux into devel
The last patch in this series makes the flags parameter for the various
gpiod_get* functions mandatory and so allows to remove an ugly cpp hack
introduced in commit 39b2bbe3d7 (gpio: add flags argument to gpiod_get*()
functions) for v3.17-rc1.
The other nine commits fix the last remaining users of these functions that
don't pass flags yet. (Only etraxfs-uart wasn't fixed; this driver's use of the
gpiod functions needs fixing anyhow.)
Assign GPIO chip owner field to chip->dev->driver->owner if it was not
configured by GPIO driver.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now nothing prevents GPIO driver from being unloaded if its gpios
were requested as GPIO IRQs only (without calling gpio_request()).
Hence, add calls of try_module_get()/module_put() into
gpiochip_irq_reqres/relres() to track such scenario properly.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_add_pingroup_range() has a pctldev argument, not pinctrl.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Now that all[1] users of the gpiod_get functions are converted to make
use of the up to now optional flags parameter, make it mandatory which
allows to remove some cpp magic.
[1] all but etraxfs-uart which is broken anyhow and I'm allowed to
ignore it by Jesper Nilsson :-)
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* acpi-video:
ACPI / video: Inline acpi_video_set_dmi_backlight_type
* device-properties:
ACPI / OF: Rename of_node() and acpi_node() to to_of_node() and to_acpi_node()
* pm-sleep:
PM / sleep: Increase default DPM watchdog timeout to 60
PM / hibernate: re-enable nonboot cpus on disable_nonboot_cpus() failure
* pm-cpuidle:
tick/idle/powerpc: Do not register idle states with CPUIDLE_FLAG_TIMER_STOP set in periodic mode
Commit 8a0662d9 introduced of_node and acpi_node symbols in global namespace
but there were already ~63 of_node local variables or function parameters
(no single acpi_node though, but anyway).
After debugging undefined but used of_node local varible (which turned out
to reference static function of_node() instead) it became clear that the names
for the functions are too short and too generic for global scope.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
kernel series:
- A big set of cleanups to the aged sysfs interface from
Johan Hovold. To get these in, v4.1-rc3 was merged into
the tree as the first patch in that series had to go
into stable. This makes the locking much more fine-grained
(get rid of the "big GPIO lock(s)" and store states in the
GPIO descriptors.
- Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
to avoid confusions.
- New drivers for:
- NXP LPC18xx (currently LPC1850)
- NetLogic XLP
- Broadcom STB SoC's
- Axis ETRAXFS
- Zynq Ultrascale+ (subdriver)
- ACPI:
- Make it possible to retrieve GpioInt resources from
a GPIO device using acpi_dev_gpio_irq_get()
- Merge some dependent I2C changes exploiting this.
- Support the ARM X-Gene GPIO standby driver.
- Make it possible for the generic GPIO driver to read
back the value set registers to reflect current
status.
- Loads of OMAP IRQ handling fixes.
- Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- Janitorial (contification, checkpatch cleanups)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vKYs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the big bulk of GPIO changes queued for the v4.2 kernel
series:
- a big set of cleanups to the aged sysfs interface from Johan
Hovold. To get these in, v4.1-rc3 was merged into the tree as the
first patch in that series had to go into stable. This makes the
locking much more fine-grained (get rid of the "big GPIO lock(s)"
and store states in the GPIO descriptors.
- rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
avoid confusions.
- New drivers for:
* NXP LPC18xx (currently LPC1850)
* NetLogic XLP
* Broadcom STB SoC's
* Axis ETRAXFS
* Zynq Ultrascale+ (subdriver)
- ACPI:
* make it possible to retrieve GpioInt resources from a GPIO
device using acpi_dev_gpio_irq_get()
* merge some dependent I2C changes exploiting this.
* support the ARM X-Gene GPIO standby driver.
- make it possible for the generic GPIO driver to read back the value
set registers to reflect current status.
- loads of OMAP IRQ handling fixes.
- incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- janitorial (constification, checkpatch cleanups)"
* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: Fix checkpatch.pl issues
gpio: pcf857x: handle only enabled irqs
gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
gpio: improve error reporting on own descriptors
gpio: promote own request failure to pr_err()
gpio: Added support to Zynq Ultrascale+ MPSoC
gpio: add ETRAXFS GPIO driver
fix documentation after renaming gpiod_set_array to gpiod_set_array_value
gpio: Add GPIO support for Broadcom STB SoCs
gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
gpio: tb10x: Drop unneeded free_irq() call
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
gpio: stp-xway: Use the of_property_read_u32 helper
gpio: pcf857x: Check for irq_set_irq_wake() failures
gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
gpio: Prevent an integer overflow in the pca953x driver
gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
gpio: omap: rework omap_gpio_request to touch only gpio specific registers
gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
...
This patch fixes some issues given by checkpatch. Fixes include
bracket placement, spacing and indenting.
Signed-off-by: Daniel Lockyer <thisisdaniellockyer@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When requesting own descriptors through hogs, it is useful to
get some details about what's going on if we encounter problems.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These error messages are helpful to see that we fail to get
hogs. Promote them to real errors so they appear in the boot
crawl.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean up chained handler and handler data if they were set by
gpiochip_set_chained_irqchip().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure to free any hogged gpios on errors in gpiochip_add.
Also move all forward declarations to the top of the file.
Fixes: f625d46017 ("gpio: add GPIO hogging mechanism")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the gpio-chip export/unexport functions to the more descriptive
names gpiochip_sysfs_register and gpiochip_sysfs_unregister.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean up gpiochip_remove somewhat and only output warning about removing
chip with GPIOs requested once.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If dev is NULL in __gpiod_get_index() and both ACPI and OF are
enabled, it will be checked twice before the code decides to give
up with DT/ACPI lookup, so avoid that.
Also use the observation that ACPI_COMPANION() is much more efficient
than ACPI_HANDLE(), because the latter uses the former and carries out
a check and a pointer dereference on top of it, so replace the
ACPI_HANDLE() check with an ACPI_COMPANION() one which does not
require the additional IS_ENABLED(CONFIG_ACPI) check too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions for conveniently obtaining and disposing of
an entire array of GPIOs with one function call.
ACPI parts tested by Mika Westerberg, DT parts tested by Rojhalat
Ibrahim.
Change log:
v5: move the ACPI functions to gpiolib-acpi.c
v4: - use shorter names for members of struct gpio_descs
- rename lut_gpio_count to platform_gpio_count for clarity
- add check for successful memory allocation
- use ERR_CAST()
v3: - rebase on current linux-gpio devel branch
- fix ACPI GPIO counting
- allow for zero-sized arrays
- make the flags argument mandatory for the new functions
- clarify documentation
v2: change interface
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Avoid multiple identical definitions of the gpio suffix strings by putting
them into a global constant array.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on Boris Brezillion's work this is a reworked patch
of his initial GPIO hogging mechanism.
This patch provides a way to initially configure specific GPIO
when the GPIO controller is probed.
The actual DT scanning to collect the GPIO specific data is performed
as part of gpiochip_add().
The purpose of this is to allow specific GPIOs to be configured
without any driver specific code.
This is particularly useful because board design are getting
increasingly complex and given SoC pins can now have more
than 10 mux values, a lot of connections are now dependent on
external IO muxes to switch various modes.
Specific drivers should not necessarily need to be aware of
what accounts to a specific board implementation. This board level
"description" should be best kept as part of the dts file.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing
memory-mapped OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for
switching several lines at once, a feature merged in
the last cycle.
- New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
- Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
- New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
- Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
- Various minor cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yWrB
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the GPIO bulk changes for the v3.20 series:
GPIOLIB core changes:
- Create and use of_mm_gpiochip_remove() for removing memory-mapped
OF GPIO chips
- GPIO MMIO library suppports bgpio_set_multiple for switching
several lines at once, a feature merged in the last cycle.
New drivers:
- New driver for the APM X-gene standby GPIO controller
- New driver for the Fujitsu MB86S7x GPIO controller
Cleanups:
- Moved rcar driver to use gpiolib irqchip
- Moxart converted to the GPIO MMIO library
- GE driver converted to GPIO MMIO library
- Move sx150x to irqdomain
- Move max732x to irqdomain
- Move vx855 to use managed resources
- Move dwapb to use managed resources
- Clean tc3589x from platform data
- Clean stmpe driver to use device tree only probe
New subtypes:
- sx1506 support in the sx150x driver
- Quark 1000 SoC support in the SCH driver
- Support X86 in the Xilinx driver
- Support PXA1928 in the PXA driver
Extended drivers:
- max732x supports device tree probe
- sx150x supports device tree probe
Various minor cleanups and bug fixes"
* tag 'gpio-v3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: kconfig: replace PPC_OF with PPC
gpio: pxa: add PXA1928 gpio type support
dt/bindings: gpio: add compatible string for marvell,pxa1928-gpio
gpio: pxa: remove mach IRQ includes
gpio: max732x: use an inline function for container cast
gpio: use sizeof() instead of hardcoded values
gpio: max732x: add set_multiple function
gpio: sch: Consolidate similar algorithms
gpio: tz1090-pdc: Use resource_size to fix off-by-one resource size calculation
gpio: ge: Convert to use devm_kstrdup
gpio: correctly use const char * const
gpio: sx150x: fixup OF support
gpio: mpc8xxx: Use of_mm_gpiochip_remove
gpio: Add Fujitsu MB86S7x GPIO driver
gpio: mpc8xxx: Convert to platform device interface.
gpio: zevio: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_mm_gpiochip_remove
gpio: gpio-mm-lantiq: Use of_property_read_u32
gpio: gpio-mm-lantiq: Do not replicate code
gpio :gpio-mm-lantiq: Use devm_kzalloc
...
gpiolib uses a fixed string for the suffixes and defines it at 32 bytes.
Later in the code snprintf is used with this fixed value of 32. Using
sizeof() is safer in case the size for the suffixes is ever changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On my previous patch I was overly hasty and made the suffixes string
array
const char const *suffixes, instaed of const char * const suffixes. This
patch corrects that
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Checkpatch complains, and probably with good reason that we should use
const char const * for the static constant array that never gets
changed.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unregister gpiochip device (used to export information through sysfs)
before removing it internally. This way removal will reverse addition.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move direct and indirect calls to gpiochip_remove_pin_ranges outside of
spin lock as they can end up taking a mutex in pinctrl_remove_gpio_range.
Note that the pin ranges are already added outside of the lock.
Fixes: 9ef0d6f762 ("gpiolib: call pin removal in chip removal function")
Fixes: f23f1516b6 ("gpiolib: provide provision to register pin ranges")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix memory leak and sleep-while-atomic in gpiochip_remove.
The memory leak was introduced by afa82fab5e ("gpio / ACPI: Move event
handling registration to gpiolib irqchip helpers") that moved the
release of acpi interrupt resources to gpiochip_irqchip_remove, but by
then the resources are no longer accessible as the acpi_gpio_chip has
already been freed by acpi_gpiochip_remove.
Note that this also fixes a few potential sleep-while-atomics, which has
been around since 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
when the call to gpiochip_irqchip_remove while holding a spinlock was
added (a couple of irq-domain paths can end up grabbing mutexes).
Fixes: afa82fab5e ("gpio / ACPI: Move event handling registration to
gpiolib irqchip helpers")
Fixes: 1425052097 ("gpio: add IRQ chip helpers in gpiolib")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix potential corruption of gpio-chip list due to failure to remove the
chip from the list before returning in gpiochip_add error path.
The chip could be long gone when the global list is next traversed,
something which could lead to a null-pointer dereference. In the best
case (chip not deallocated) we are just leaking the gpio range.
Fixes: 14e85c0e69 ("gpio: remove gpio_descs global array")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Memory allocated and references taken by of_gpiochip_add and
acpi_gpiochip_add were never released on errors in gpiochip_add (e.g.
failure to find free gpio range).
Fixes: 391c970c0d ("of/gpio: add default of_xlate function if device
has a node pointer")
Fixes: 664e3e5ac6 ("gpio / ACPI: register to ACPI events
automatically")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A new API that allows setting more than one GPIO at the
time. This is implemented for the new descriptor-based
API only and makes it possible to e.g. toggle a clock and
data line at the same time, if the hardware can do this
with a single register write. Both consumers and drivers
need new calls, and the core will fall back to driving
individual lines where needed. Implemented for the MPC8xxx
driver initially.
- Patched the mdio-mux-gpio and the serial mctrl driver
that drives modems to use the new multiple-setting API
to set several signals simultaneously.
- Get rid of the global GPIO descriptor array, and instead
allocate descriptors dynamically for each GPIO on a certain
GPIO chip. This moves us closer to getting rid of the
limitation of using the global, static GPIO numberspace.
- New driver and device tree bindings for 74xx ICs.
- New driver and device tree bindings for the VF610 Vybrid.
- Support the RCAR r8a7793 and r8a7794.
- Guidelines for GPIO device tree bindings trying to get
things a bit more strict with the advent of combined
device properties.
- Suspend/resume support for the MVEBU driver.
- A slew of minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZAhA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
Commit 14e85c0e69 ("gpio: remove gpio_descs global array") changed
gpio_to_desc()'s behavior to return NULL not only for GPIOs numbers
not in the valid range, but also for all GPIOs whose controller has not
been probed yet. Although this behavior is more correct (nothing hints
that these GPIO numbers will be populated later), this affects
gpio_request() and gpio_request_one() which call gpiod_request() with a
NULL descriptor, causing it to return -EINVAL instead of the expected
-EPROBE_DEFER for a non-probed GPIO.
gpiod_request() is only called with a descriptor obtained from
gpio_to_desc() from these two functions, so address the issue there.
Other ways to obtain GPIOs rely on well-defined mappings and can thus
return -EPROBE_DEFER only for relevant GPIOs, and are thus not affected
by this issue.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Although gpiod_get_direction() can be considered side-effect free for
consumers, its internals involve setting or clearing bits in the
affected GPIO descriptor, for which we need to force-cast the const
descriptor variable to non-const. This could lead to incorrect behavior
if the compiler decides to optimize here, so remove this const
attribute. The intent is to make gpiod_get_direction() private anyway,
so it does not really matter.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ARCH_NR_GPIOS-sized static array of GPIO descriptors by
dynamically-allocated arrays for each GPIO chip.
This change makes gpio_to_desc() perform in O(n) (where n is the number
of GPIO chips registered) instead of O(1), however since n is rarely
bigger than 1 or 2 no noticeable performance issue is expected.
Besides this provides more incentive for GPIO consumers to move to the
gpiod interface. One could use a O(log(n)) structure to link the GPIO
chips together, but considering the low limit of n the hypothetical
performance benefit is probably not worth the added complexity.
This patch uses kcalloc() in gpiochip_add(), which removes the ability
to add a chip before kcalloc() can operate. I am not aware of such
cases, but if someone bisects up to this patch then I will be proven
wrong...
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It doesn't make much sense to make some (possible expensive) calls to
gpio_is_valid() first, and to ignore the result if the base number is
negative. Check for a positive base number first.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers need to deal with only firmware representation of its
GPIOs. An example would be a GPIO button array driver where each button
is described as a separate firmware node in device tree. Typically these
child nodes do not have physical representation in the Linux device
model.
In order to help device drivers to handle such firmware child nodes we
add dev[m]_get_named_gpiod_from_child() that takes a child firmware
node pointer as its second argument (the first one is the parent device
itself), finds the GPIO using whatever is the underlying firmware
method, and requests the GPIO properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With release of ACPI 5.1 and _DSD method we can finally name GPIOs (and
other things as well) returned by _CRS. Previously we were only able to
use integer index to find the corresponding GPIO, which is pretty error
prone if the order changes.
With _DSD we can now query GPIOs using name instead of an integer index,
like the below example shows:
// Bluetooth device with reset and shutdown GPIOs
Device (BTH)
{
Name (_HID, ...)
Name (_CRS, ResourceTemplate ()
{
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {15}
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {27, 31}
})
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () {"reset-gpio", Package() {^BTH, 1, 1, 0 }},
Package () {"shutdown-gpio", Package() {^BTH, 0, 0, 0 }},
}
})
}
The format of the supported GPIO property is:
Package () { "name", Package () { ref, index, pin, active_low }}
ref - The device that has _CRS containing GpioIo()/GpioInt() resources,
typically this is the device itself (BTH in our case).
index - Index of the GpioIo()/GpioInt() resource in _CRS starting from zero.
pin - Pin in the GpioIo()/GpioInt() resource. Typically this is zero.
active_low - If 1 the GPIO is marked as active_low.
Since ACPI GpioIo() resource does not have field saying whether it is
active low or high, the "active_low" argument can be used here. Setting
it to 1 marks the GPIO as active low.
In our Bluetooth example the "reset-gpio" refers to the second GpioIo()
resource, second pin in that resource with the GPIO number of 31.
This patch implements necessary support to gpiolib for extracting GPIOs
using _DSD device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
To unify how we connect cascaded IRQ chips to parent IRQs, if
NULL us passed as handler to the gpiochip_set_chained_irqchip()
function, assume the chips is nested rather than chained, and
we still get the parent set up correctly by way of this function
call.
Alter the drivers for tc3589x and stmpe to use this to set up
their chained handlers as a demonstration of the usage.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the IRQ from the parent is nested the IRQ may need to be
resent under certain conditions. Currently the chained IRQ
handler in gpiolib does not handle connecting nested IRQs
but it is conceptually correct to indicate the actual parent
IRQ.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no guarantee that VIRQs will be allocated sequentially
for gpio irqchip in gpiochip_irqchip_add().
Therefore, it's unsafe to dispose VIRQ in gpiochip_irqchip_remove()
basing on index relatively to stored irq_base value.
Hence, use irq_find_mapping for VIRQ finding in gpiochip_irqchip_remove()
instead of irq_base + index.
Reported-by: Wang, Yalin <Yalin.Wang@sonymobile.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is possibility with misconfigured pins that interrupt occurs instantly
after setting irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Now if handler gets called before irq_set_handler_data() the handler gets
NULL handler data.
Fix this by moving irq_set_handler_data() call before
irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Cc: Stable <stable@vger.kernel.org> # 3.15+
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
GPIO direction flags are not getting set because
an 'if' statement is the wrong way around.
Cc: Stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current prototype of gpiochip_request_own_desc() requires to obtain
a pointer to a descriptor. This is in contradiction to all other GPIO
request schemes, and imposes an extra step of obtaining a descriptor to
drivers. Most drivers actually cannot even perform that step since the
function that does it (gpichip_get_desc()) is gpiolib-private.
Change gpiochip_request_own_desc() to return a descriptor from a
(chip, hwnum) tuple and update users of this function (currently
gpiolib-acpi only).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The huge majority of GPIOs have their direction and initial value set
right after being obtained by one of the gpiod_get() functions. The
integer GPIO API had gpio_request_one() that took a convenience flags
parameter allowing to specify an direction and value applied to the
returned GPIO. This feature greatly simplifies client code and ensures
errors are always handled properly.
A similar feature has been requested for the gpiod API. Since setting
the direction of a GPIO is so often the very next action done after
obtaining its descriptor, we prefer to extend the existing functions
instead of introducing new functions that would raise the
number of gpiod getters to 16 (!).
The drawback of this approach is that all gpiod clients need to be
updated. To limit the pain, temporary macros are introduced that allow
gpiod_get*() to be called with or without the extra flags argument. They
will be removed once all consumer code has been updated.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since now we have irqchip helpers that the GPIO chip drivers are supposed
to use if possible, we can move the registration of ACPI events to happen
in these helpers. This seems to be more natural place and might encourage
GPIO chip driver writers to take advantage of the irqchip helpers.
We make the functions available to GPIO chip drivers via private gpiolib.h,
just in case generic irqchip helpers are not suitable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per example from the regulator subsystem: put all defines and
functions related to registering board info for GPIO descriptors
into a separate <linux/gpio/machine.h> header.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both functions were introduced to let gpio drivers request their own
gpio pins. Without exporting the functions, this can however only be
used by gpio drivers built into the kernel.
Secondary impact is that the functions can not currently be used by
platform initialization code associated with the gpio-pca953x driver.
This code permits auto-export of gpio pins through platform data, but
if this functionality is used, the module can no longer be unloaded due
to the problem solved with the introduction of gpiochip_request_own_desc
and gpiochip_free_own_desc.
Export both function so they can be used from modules and from
platform initialization code.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_ensure_requested() only makes sense when using the integer-based
GPIO API, so make sure it is called from there instead of the gpiod
API which we know cannot be called with a non-requested GPIO anyway.
The uses of gpio_ensure_requested() in the gpiod API were kind of
out-of-place anyway, so putting them in gpio-legacy.c helps clearing the
code.
Actually, considering the time this ensure_requested mechanism has been
around, maybe we should just turn this patch into "remove
gpio_ensure_requested()" if we know for sure that no user depend on it
anymore?
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_lock/unlock_as_irq() are working with (chip, offset) arguments and
are thus not using the old integer namespace. Therefore, there is no
reason to have gpiod variants of these functions working with
descriptors, especially since the (chip, offset) tuple is more suitable
to the users of these functions (GPIO drivers, whereas GPIO descriptors
are targeted at GPIO consumers).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As GPIO descriptors are not going to remain unique anymore, having this
function public is not safe. Restrain its use to gpiolib since we have
no user outside of it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old integer GPIO interface is, in effect, a privileged user of the
gpiod interface. Reflect this fact further by moving legacy GPIO support
into its own source file. This makes the code clearer and will allow us
to disable legacy GPIO support in the (far) future.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sysfs support is currently entangled within the core GPIO support, while
it should relly just be a (privileged) user of the integer GPIO API.
This patch is a first step towards making the gpiolib code more readable
by splitting it into logical parts.
Move all sysfs support to their own source file, and share static
members of gpiolib that need to be in the private gpiolib.h file. In
the future we will want to put some of them back into gpiolib.c, but this
first patch let us at least identify them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Compiling out GPIO labels results in a space gain so small that it can
hardly be justified. Labels can also be useful for printing debug
messages, so always keep them around.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit dd34c37aa3 (gpio: of: Allow -gpio suffix for property names)
added parsing for both -gpio and -gpios suffix but also changed
the handling for deferred probe unintentionally. Because of the
looping the second name will now return -ENOENT instead of
-EPROBE_DEFER. Fix the issue by breaking out of the loop if
-EPROBE_DEFER is encountered.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce gpiod_get_optional() and gpiod_get_index_optional() helpers
that make it easier for drivers to handle optional GPIOs.
Currently in order to handle optional GPIOs, a driver needs to special
case error handling for -ENOENT, such as this:
gpio = gpiod_get(dev, "foo");
if (IS_ERR(gpio)) {
if (PTR_ERR(gpio) != -ENOENT)
return PTR_ERR(gpio);
gpio = NULL;
}
if (gpio) {
/* set up GPIO */
}
With these new helpers the above is reduced to:
gpio = gpiod_get_optional(dev, "foo");
if (IS_ERR(gpio))
return PTR_ERR(gpio);
if (gpio) {
/* set up GPIO */
}
While at it, device-managed variants of these functions are also
provided.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function is called gpiod_get(), not gpio_get(). Fix the kernel-doc
comment to match the name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many bindings use the -gpio suffix in property names. Support this in
addition to the -gpios suffix when requesting GPIOs using the new
descriptor-based API.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_find_gpio() is always called under an IS_ENABLED(CONFIG_OF), so the
dummy implementation provided for !OF configurations is not needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO irqchip drivers exploit the irqdomain mapping
function to set up the IRQ default type in the hardware,
make sure that if we pass IRQ_TYPE_NONE, no hardware setup
whatsoever takes place (this should be the norm) until
later when the IRQ gets utilized.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: linux-omap <linux-omap@vger.kernel.org>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Another feature that is duplicated in a number of GPIO irqchips
is that these cascades IRQs are assigned their own lock class
so as to avoid warnings about lockdep recursions. Do this also
in the generic GPIO irqchip helpers for smooth transition to
this core infrastructure.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some off-chip GPIO expanders need to be communicated by I2C or
SPI traffic, but may still support IRQs. By the sleeping nature
of such buses, such IRQ handlers need to be threaded. Support
such handlers in the gpiochip irqchip helpers by flagging IRQs
as threaded if the .can_sleep property of the gpiochip is
true.
Helpfully deny registration of chained IRQ handlers if the
.can_sleep property is set, as such chips will invariably need
a nested handler rather than a chained handler.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During irq mapping, in irq_set_chip_and_handler() the process
of setting this up may incur calls to lock the irqchip, which
in turn may need to dereference and use the chip data. So set
the data first, then set the chip and handler.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using the irqchip helper inside the gpiolib, make sure
the IRQs are unmapped/disposed before the irqdomain is removed
as part of removing the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a function gpiochip_irqchip_add() to set
up an irqchip for a GPIO controller, and a function
gpiochip_set_chained_irqchip() to chain it to a parent
irqchip.
Most GPIOs are of the type where a number of lines form
a cascaded interrupt controller chained onto
the primary system interrupt controller (or further down the
chain) so let's add this helper and factor the code to
request the lines to be used as IRQs, the .to_irq() function
and the irqdomain into the core as well.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nothing prevents GPIO drivers from returning values outside the
boolean range, and as it turns out a few drivers are actually doing so.
These values were passed as-is to unsuspecting consumers and created
confusion.
This patch makes the internal _gpiod_get_raw_value() function return a
bool, effectively clamping the GPIO value to the boolean range no
matter what the driver does.
While we are at it, we also change the value parameter of
_gpiod_set_raw_value() to bool type before drivers start doing funny
things with it as well.
Another way to fix this would be to change the prototypes of the driver
interface to use bool directly, but this would require a huge
cross-systems patch so this simpler solution is preferred.
Changes since v1:
- Change local variable type to bool as well, use boolean values in
code
- Also change prototype of open drain/open source setting functions
since they are only called from _gpiod_set_raw_value()
This probably calls for a larger booleanization of gpiolib, but let's
keep that for a latter change - right now we need to address the issue
of non-boolean values returned by drivers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current ACPI GPIO event handling code was never tested against real
hardware with functioning GPIO triggered events (at the time such hardware
wasn't available). Thus it misses certain things like requesting the GPIOs
properly, passing correct flags to the interrupt handler and so on.
This patch reworks ACPI GPIO event handling so that we:
1) Use struct acpi_gpio_event for all GPIO signaled events.
2) Switch to use GPIO descriptor API and request GPIOs by calling
gpiochip_request_own_desc() that we added in a previous patch.
3) Pass proper flags from ACPI GPIO resource to request_threaded_irq().
Also instead of open-coding the _AEI iteration loop we can use
acpi_walk_resources(). This simplifies the code a bit and fixes memory leak
that was caused by missing kfree() for buffer returned by
acpi_get_event_resources().
Since the remove path now calls gpiochip_free_own_desc() which takes GPIO
spinlock we need to call acpi_gpiochip_remove() outside of that lock
(analogous to acpi_gpiochip_add() path where the lock is released before
those funtions are called).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sometimes it is useful to allow GPIO chips themselves to request GPIOs they
own through gpiolib API. One use case is ACPI ASL code that should be able
to toggle GPIOs through GPIO operation regions.
We can't use gpio_request() because it will pin the module to the kernel
forever (it calls try_module_get()). To solve this we move module refcount
manipulation to gpiod_request() and let __gpiod_request() handle the actual
request. This changes the sequence a bit as now try_module_get() is called
outside of gpio_lock (I think this is safe, try_module_get() handles
serialization it needs already).
Then we provide gpiolib internal functions gpiochip_request/free_own_desc()
that do the same as gpio_request() but don't manipulate module refrence
count. This allows the GPIO chip driver to request and free descriptors it
owns without being pinned to the kernel forever.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is currently debated where the functions to lock a certain
GPIO line as used for IRQs should be called. Delete all
misleading documentation.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers dealing with a gpio_chip might need to act on its
descriptors directly; one example is pinctrl drivers that need to lock a
GPIO for being used as IRQ using gpiod_lock_as_irq().
This patch exports a gpiochip_get_desc() function that returns the
GPIO descriptor at the requested index. It also sweeps the
gpio_to_chip() function out of the consumer interface since any holder
of a gpio_chip reference can manipulate its GPIOs way beyond what a
consumer should be allowed to do.
As a result, gpio_chip is not visible anymore to simple GPIO consumers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The documentation was not clear about whether
gpio_direction_output should take a logical value or the physical
level on the output line, i.e. whether the ACTIVE_LOW status
would be taken into account.
This converts gpiod_direction_output to use the logical level
and adds a new gpiod_direction_output_raw for the raw value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A big set this merge window, as we have much going on in
this subsystem. Major changes this time:
- Some core improvements and cleanups to the new GPIO
descriptor API. This seems to be working now so we can
start the exodus to this API, moving gradually away from
the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move
the few GPIO ACPI clients we have to the GPIO descriptor
API right *now* before we go any further. We actually
managed to contain this *before* we started to litter
the kernel with yet another hackish global numberspace for
the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have
been migrated to use the GPIO descriptors rather than
fixed number assignments. Tegra machine has been migrated
as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x.
Those should be really good examples of how I expect a
nice GPIO driver to look these days.
- Do away with custom GPIO implementations on a major
part of the ARM machines: ks8695, lpc32xx, mv78xx0.
Make a first step towards the same in the horribly
convoluted Samsung S3C include forest. We expect to
continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em,
intel-mid and lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line
is used for IRQs and can then enforce some semantics such
as disallowing a GPIO line marked as in use for IRQ to be
switched to output mode.
- Drop all use of irq_set_chip_and_handler_name().
The name provided in these cases were just unhelpful
tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em
74x164 and msm drivers.
- Some non-urgent bug fixes here and there, duplicate
#includes and that usual kind of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lW2i
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
Now that all users of acpi_gpio.h have been moved to use either the GPIO
descriptor interface or to the internal gpiolib.h we can get rid of
acpi_gpio.h entirely.
Once this is done the only interface to get GPIOs to drivers enumerated
from ACPI namespace is the descriptor based interface.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.
We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.
Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some devices drivers make use of optional GPIO parameters. For such
drivers, it is important to discriminate between the case where no
GPIO mapping has been defined for the function they are requesting, and
the case where a mapping exists but an error occured while resolving it
or when acquiring the GPIO.
This patch changes the family of gpiod_get() functions such that they
will return -ENOENT if and only if no GPIO mapping is defined for the
requested function. Other error codes are used when an actual error
occured during the GPIO resolution.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
This patch performs the following renames.
* s/sysfs_elem_dir/kernfs_elem_dir/
* s/sysfs_elem_symlink/kernfs_elem_symlink/
* s/sysfs_elem_attr/kernfs_elem_file/
* s/sysfs_dirent/kernfs_node/
* s/sd/kn/ in kernfs proper
* s/parent_sd/parent/
* s/target_sd/target/
* s/dir_sd/parent/
* s/to_sysfs_dirent()/rb_to_kn()/
* misc renames of local vars when they conflict with the above
Because md, mic and gpio dig into sysfs details, this patch ends up
modifying them. All are sysfs_dirent renames and trivial. While we
can avoid these by introducing a dummy wrapping struct sysfs_dirent
around kernfs_node, given the limited usage outside kernfs and sysfs
proper, I don't think such workaround is called for.
This patch is strictly rename only and doesn't introduce any
functional difference.
- mic / gpio renames were missing. Spotted by kbuild test robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch just accents that @dev could be NULL.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In several places we are printing messages with prefix based on chip->label.
Introduced macros help us to do this easier and in uniform way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch includes the following amendments:
1) use "?" as a label when the last one is not defined in gpiod_*;
2) whenever it's possible gpiod_* are used;
3) print a function name, if it's already used in other messages.
Additionally it fixes an indentation in few places.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change the format of the platform GPIO lookup tables to make them less
confusing and improve lookup efficiency.
The previous format was a single linked-list that required to compare
the device name and function ID of every single GPIO defined for each
lookup. Switch that to a list of per-device tables, so that the lookup
can be done in two steps, omitting the GPIOs that are not relevant for a
particular device.
The matching rules are now defined as follows:
- The device name must match *exactly*, and can be NULL for GPIOs not
assigned to a particular device,
- If the function ID in the lookup table is NULL, the con_id argument of
gpiod_get() will not be used for lookup. However, if it is defined, it
must match exactly.
- The index must always match.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the two members of struct gpio_chip that were
defined as unsigned foo:1 to bool, because that is indeed what
they are. Switch all users in the gpio and pinctrl subsystems
to assign these values with true/false instead of 0/1. The
users outside these subsystems will survive since true/false
is 1/0, atleast we set some kind of more strict typing example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_offset_to_desc() was using gpio_to_desc(), which directly
addresses the global GPIO array we are hoping to get rid of someday.
Reimplement it using the descriptor array of the chip itself, after
checking the requested offset is within the valid bounds of the chip.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's the drivers responsibility to react on failure to get
the gpio descriptors and not the frameworks. Since there are
some common peripherals that may or may not have certain
pins connected to gpio lines, depending on the platform,
printing the warning there may end up generating useless bug
reports.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For platforms that use device tree or ACPI as the standard way to look
GPIOs up, allow the platform-defined GPIO mappings to be used as a
fallback. This may be useful for platforms that need extra GPIOs mappings
not defined by the firmware.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The prototype for static GPIO lookup functions has been updated to use
an explicit type for GPIO lookup flags. Unfortunately the definition of
of_find_gpio() when CONFIG_OF is not defined has been omitted, which
triggers a warning. This patch fixes this.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO mapping properties were defined using the GPIOF_* flags, which are
declared in linux/gpio.h. This file is not included when using the
GPIO descriptor interface.
This patch declares the flags that can be used as GPIO mappings
properties in linux/gpio/driver.h, and uses them in gpiolib, so that no
deprecated declarations are used by the GPIO descriptor interface.
This patch also allows GPIO_OPEN_DRAIN and GPIO_OPEN_SOURCE to be
specified as GPIO mapping properties.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
find_chip_by_name() was incorrectly implemented by using
gpio_lookup_list instead of gpiod_chips to iterate through all the
registered GPIO controllers. This patch reimplements it by using
gpiochip_find() with a custom search function, which simplifies the code
on top of fixing the mistake.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
- Merged the GPIO descriptor API from Alexandre Courbot.
This is a first step toward trying to get rid of the
global GPIO numberspace for the future.
- Add an API so that driver can flag that a certain GPIO
line is being used by a irqchip backend for generating
IRQs, so that we can enforce checks, like not allowing
users to switch that line to an output at runtime, since
this makes no sense. Implemented corresponding calls
in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting
rid of a bunch of custom GPIO implementations from the
arch/arm/* tree:
- Move the IOP GPIO driver to the GPIO subsystem and
fix all users to use the gpiolib API for accessing
GPIOs. Delete the old custom GPIO implementation.
- Delete the unused custom PXA GPIO implemention.
- Convert all users of the IXP4 custom GPIO
implementation to use gpiolib and delete the custom
implementation.
- Delete the custom Gemini GPIO implementation, also
completely unused.
- Various cleanups and renamings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=881E
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"Here is the bulk of GPIO changes for the v3.13 development cycle.
I've got ACKs for the things that affect other subsystems (or it's my
own subsystem, like pinctrl). Most of that pertain to an attempt from
my side to consolidate and get rid of custom GPIO implementations in
the ARM tree. I will continue doing this.
The main change this time is the new GPIO descriptor API, background
for this can be found in Corbet's summary from this january in LWN:
http://lwn.net/Articles/533632/
Summary:
- Merged the GPIO descriptor API from Alexandre Courbot. This is a
first step toward trying to get rid of the global GPIO numberspace
for the future.
- Add an API so that driver can flag that a certain GPIO line is
being used by a irqchip backend for generating IRQs, so that we can
enforce checks, like not allowing users to switch that line to an
output at runtime, since this makes no sense. Implemented
corresponding calls in a few select drivers.
- ACPI GPIO cleanups, refactorings and switch to using the
descriptor-based interface.
- Support for the TPS80036 Palmas GPIO variant.
- A new driver for the Broadcom Kona GPIO SoC IP block.
- Device tree support for the PCF857x driver.
- A set of ARM GPIO refactorings with the goal of getting rid of a
bunch of custom GPIO implementations from the arch/arm/* tree:
* Move the IOP GPIO driver to the GPIO subsystem and fix all users
to use the gpiolib API for accessing GPIOs. Delete the old
custom GPIO implementation.
* Delete the unused custom PXA GPIO implemention.
* Convert all users of the IXP4 custom GPIO implementation to use
gpiolib and delete the custom implementation.
* Delete the custom Gemini GPIO implementation, also completely
unused.
- Various cleanups and renamings"
* tag 'gpio-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: gpio-mxs: Remove unneeded dt checks
gpio: pl061: don't depend on CONFIG_ARM
gpio: bcm-kona: add missing .owner to struct gpio_chip
gpiolib: provide a declaration of seq_file in gpio/driver.h
gpiolib: include gpio/consumer.h in of_gpio.h for desc_to_gpio()
gpio: provide stubs for devres gpio functions
gpiolib: devres: add missing headers
gpiolib: make GPIO_DEVRES depend on GPIOLIB
gpiolib: devres: fix devm_gpiod_get_index()
gpiolib / ACPI: document the GPIO descriptor based interface
gpiolib / ACPI: allow passing GPIOF_ACTIVE_LOW for GpioInt resources
gpiolib / ACPI: add ACPI support for gpiod_get_index()
gpiolib / ACPI: convert to gpiod interfaces
gpiolib: add gpiod_get() and gpiod_put() functions
gpiolib: port of_ functions to use gpiod
gpiolib: export descriptor-based GPIO interface
Fixup "MAINTAINERS: GPIO-INTEL-MID: add maintainer"
gpio: bcm281xx: Don't print addresses of GPIO area in probe()
gpio: tegra: use new gpio_lock_as_irq() API
gpio: rcar: Include linux/of.h header
...
- Blackfin ADI pin control driver, we move yet another
architecture under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control
driver. New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things,
this enabled simplified device tree bindings by referring
entire groups of pins on some pin controller to act as
back-end for a certain GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged
through this tree, so the ARC has full support for pins
and GPIOs after this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin
controller instances. The i.MX1 and i.MX27 is an entirely
new family (silicon) of controllers whereas i.MX50 is
a variant of the previous supported controller.
- Then the usual slew of fixes, cleanups and incremental
updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=z9SM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Main pin control pull request for the v3.13 cycle.
The changes hitting arch/blackfin are ACKed by the Blackfin
maintainer, and the device tree bindings are ACKed to the extent
possible by someone from the device tree maintainers group.
- Blackfin ADI pin control driver, we move yet another architecture
under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control driver.
New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things, this
enabled simplified device tree bindings by referring entire groups
of pins on some pin controller to act as back-end for a certain
GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged through
this tree, so the ARC has full support for pins and GPIOs after
this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
instances. The i.MX1 and i.MX27 is an entirely new family
(silicon) of controllers whereas i.MX50 is a variant of the
previous supported controller.
- Then the usual slew of fixes, cleanups and incremental updates"
The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.
* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: imx50: add pinctrl support code for the IMX50 SoC
pinctrl: at91: copy define to driver
pinctrl: remove minor dead code
pinctrl: imx: fix using pin->input_val wrongly
pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
gpio: tb10x: fix return value check in tb10x_gpio_probe()
gpio: tb10x: use module_platform_driver to simplify the code
pinctrl: imx27: imx27 pincontrol driver
pinctrl: imx1 core driver
pinctrl: sh-pfc: r8a7791 PFC support
sh-pfc: r8a7778: Add CAN pin groups
gpio: add TB10x GPIO driver
pinctrl: at91: correct a few typos
pinctrl: mvebu: remove redundant of_match_ptr
pinctrl: tb10x: use module_platform_driver to simplify the code
pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
pinctrl: add documentation for pinctrl_get_group_pins()
pinctrl: rockchip: emulate both edge triggered interrupts
pinctrl: rockchip: add rk3188 specifics
pinctrl: rockchip: remove redundant check
...
The ACPI GpioInt resources contain polarity field that is used to specify
whether the interrupt is active high or low. Since gpiolib supports
GPIOF_ACTIVE_LOW we can pass this information in the flags field in
acpi_find_gpio(), analogous to the DeviceTree version.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiod_get_index() and gpiod_get() are now the new preferred way to request
GPIOs. Add support for finding the corresponding GPIO descriptor from ACPI
namespace.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add gpiod_get(), gpiod_get_index() and gpiod_put() functions that
provide safer management of GPIOs.
These functions put the GPIO framework in line with the conventions of
other frameworks in the kernel, and help ensure every GPIO is declared
properly and valid while it is used.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch exports the gpiod_* family of API functions, a safer
alternative to the legacy GPIO interface. Differences between the gpiod
and legacy gpio APIs are:
- gpio works with integers, whereas gpiod operates on opaque handlers
which cannot be forged or used before proper acquisition
- gpiod get/set functions are aware of the active low state of a GPIO
- gpio consumers should now include <linux/gpio/consumer.h> to access
the new interface, whereas chips drivers will use
<linux/gpio/driver.h>
The legacy gpio API is now built as inline functions on top of gpiod.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the infrastructure required to register non-linear gpio
ranges through gpiolib and the standard GPIO device tree bindings.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is currently often possible in many GPIO drivers to request
a GPIO line to be used as IRQ after calling gpio_to_irq() and,
as the gpiolib is not aware of this, set the same line to
output and start driving it, with undesired side effects.
As it is a bogus usage scenario to request a line flagged as
output to used as IRQ, we introduce APIs to let gpiolib track
the use of a line as IRQ, and also set this flag from the
userspace ABI.
The API is symmetric so that lines can also be flagged from
.irq_enable() and unflagged from IRQ by .irq_disable().
The debugfs file is altered so that we see if a line is
reserved for IRQ.
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Patch be1a4b brought some improvements to the GPIO error handling code,
but also changed the return value of gpiod_request() when called on a
not yet initialized GPIO descriptor: it now returns -EINVAL instead of
-EPROBE_DEFER, and this affects some drivers.
This patch restores the original behavior for gpiod_request(). It is
safe to do so now that desc_to_gpio() does not rely on the GPIO
descriptor to be initialized. Other functions changed by patch be1a4b
do not see their return value affected, so these are not reverted.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Dr. H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current implementation of desc_to_gpio() relies on the chip pointer
to be set to a valid value in order to compute the GPIO number. This
was done in the hope that we can get rid of the gpio_desc global array,
but this is not happening anytime soon.
This patch reimplements desc_to_gpio() in a fashion similar to that of
gpio_to_desc(). As a result, desc_to_gpio(gpio_to_desc(gpio)) == gpio is
now always true. This allows to call desc_to_gpio() on non-initialized
descriptors as some error-handling code currently does.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Dr. H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pre-existing sysfs interfaces which take explicit namespace
argument are weird in that they place the optional @ns in front of
@name which is contrary to the established convention. For example,
we end up forcing vast majority of sysfs_get_dirent() users to do
sysfs_get_dirent(parent, NULL, name), which is silly and error-prone
especially as @ns and @name may be interchanged without causing
compilation warning.
This renames sysfs_get_dirent() to sysfs_get_dirent_ns() and swap the
positions of @name and @ns, and sysfs_get_dirent() is now a wrapper
around sysfs_get_dirent_ns(). This makes confusions a lot less
likely.
There are other interfaces which take @ns before @name. They'll be
updated by following patches.
This patch doesn't introduce any functional changes.
v2: EXPORT_SYMBOL_GPL() wasn't updated leading to undefined symbol
error on module builds. Reported by build test robot. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gpiod_get/set functions share common code between their regular and
cansleep variants. The exporting of the gpiod interface will make
the situation worse. This patch factorizes the common code to avoid code
redundancy.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide the human readable label for the GPIO as well as the number when
we are recording it in order to improve the readability of log messages.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently many but not all GPIO log messages log the GPIO number and the
formats vary. Ensure that this is done consistently by defining logging
helpers which take the GPIO descriptor.
The will help people pattern matching on logs and providing the number
makes the log messages that omitted it more useful.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears some drivers are using gpio_set_debounce()
opportunistically, i.e. without knowing whether it works or
not. (Example: input/keyboard/gpio_keys.c) to account for
this use case, return -ENOTSUPP and do not print any
warnings in this case.
Took a round over the other gpio_set_debounce() consumers
to make sure that none of them are relying on the returned
error code to be something specific.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At several places the gpiolib will proceed to handle a GPIO
descriptor even if it's ->chip member is NULL and no gpiochip
is associated.
Fix this by checking that both the descriptor cookie *and*
the chip pointer are valid.
Also bail out earlier with more specific diagnostic messages
on missing operations for setting as input/output or debounce.
ChangeLog v1->v2:
- Also return -EIO on gpiod_set_debounce() with missing
operations in the vtable
- Fix indentations.
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Frank Rowand <frank.rowand@sonymobile.com>
Cc: Tim Bird <tim.bird@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This comment applies to gpio_to_chip(), not gpiod_to_chip().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Constify descriptor parameter of gpiod_* functions for those that
should obviously not modify it. This includes value or direction get,
cansleep, and IRQ number query.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some functions dereferenced their GPIO descriptor argument without
checking its validity first, potentially leading to an oops when given
an invalid argument.
This patch also makes gpio_get_value() more resilient when given an
invalid GPIO, returning 0 instead of silently crashing.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This branch contains the usual set of individual driver improvements and
bug fixes, as well as updates to the core code. The more notable changes
include:
- Internally add new API for referencing GPIOs by gpio_desc instead of
number. Eventually this will become a public API
- ACPI GPIO binding support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JN4M
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull GPIO changes from Grant Likely:
"This branch contains the usual set of individual driver improvements
and bug fixes, as well as updates to the core code. The more notable
changes include:
- Internally add new API for referencing GPIOs by gpio_desc instead
of number. Eventually this will become a public API
- ACPI GPIO binding support"
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (33 commits)
arm64: select ARCH_WANT_OPTIONAL_GPIOLIB
gpio: em: Use irq_domain_add_simple() to fix runtime error
gpio: using common order: let 'static const' instead of 'const static'
gpio/vt8500: memory cleanup missing
gpiolib: Fix locking on gpio debugfs files
gpiolib: let gpio_chip reference its descriptors
gpiolib: use descriptors internally
gpiolib: use gpio_chips list in gpiochip_find_base
gpiolib: use gpio_chips list in sysfs ops
gpiolib: use gpio_chips list in gpiochip_find
gpiolib: use gpio_chips list in gpiolib_sysfs_init
gpiolib: link all gpio_chips using a list
gpio/langwell: cleanup driver
gpio/langwell: Add Cloverview ids to pci device table
gpio/lynxpoint: add chipset gpio driver.
gpiolib: add missing braces in gpio_direction_show
gpiolib-acpi: Fix error checks in interrupt requesting
gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
gpiolib: remove gpiochip_reserve()
arm: pxa: tosa: do not use gpiochip_reserve()
...
The debugfs files really need to hold the gpiolib spinlock before
accessing the list. Otherwise chip addition/removal will cause an oops.
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a pointer to the gpio_chip structure that references the array of
GPIO descriptors belonging to the chip, and update gpiolib code to use
this pointer instead of the global gpio_desc[] array. This is another
step towards the removal of the gpio_desc[] global array.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.orh>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make sure gpiolib works internally with descriptors and (chip, offset)
pairs instead of using the global integer namespace. This prepares the
ground for the removal of the global gpio_desc[] array and the
introduction of the descriptor-based GPIO API.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[grant.likely: Squash in fix for link error when CONFIG_SYSFS=n]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Re-implement gpiochip_find_base using the list of chips instead of the
global gpio_desc[] array. This makes it both simpler and more efficient,
and is needed to remove the global descriptors array.
The new code should preserve the exact same GPIO number assignment
policy as the code it is replacing. There shouldn't be any visible
change to the assigned GPIO numbers.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[grant.likely: Added comment about assignment policy]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This makes the code both simpler and faster compared to parsing the GPIO
number space.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Using the GPIO chips list is much faster than parsing the entire GPIO
number space.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the small list of GPIO chips instead of parsing the whole GPIO
number space.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a list member to gpio_chip that allows all chips to be parsed
quickly. The current method requires parsing the entire GPIO integer
space, which is painfully slow. Using a list makes many chip operations
that involve lookup or parsing faster, and also simplifies the code. It
is also necessary to eventually get rid of the global gpio_desc[] array.
The list of gpio_chips is always ordered by base GPIO number to ensure
chips traversal is done in the right order.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
All in-kernel users of class_find_device() don't really need mutable
data for match callback.
In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.
The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.
Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laxman Dewangan