Use TEGRA_GPIO() macro to name all GPIOs referenced by GPIO properties,
and some interrupts properties. Use standard GPIO flag defines too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch updates all Tegra board files so that they contain all the
properties required by the updated USB DT binding. Note that this patch
only adds the new properties and does not yet remove the old properties,
in order to maintain bisectability. The old properties will be removed
once the driver has been updated to assume the new bindings.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
[swarren: fixed some newly added regulator-name properties to better
match schematic, avoided duplicate regulator-name on Whistler.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
1. All Tegra20 ULPI reset GPIO DT properties are modified to indicate active
low nature of the GPIO.
2. Placed USB PHY DT node immediately below the EHCI controller DT nodes
and corrected reg value in the name of USB PHY DT node.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Correct IDs for cdev1 and cdev2 are 94 and 93 respectively.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: split into separate driver and device-tree patches]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the power gpio key to DT and enable the wakeup of the gpio key
for the device. The Seaboard and paz00 already had the power gpio key
binding and the power key of Whistler was on KBC. So these boards' device
tree didn't include in this patch.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The GPIO pin of SD slot card detection should active low.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UMMs
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree updates
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
* tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (22 commits)
ARM: dt: tegra30: Rename "smmu" to "iommu"
ARM: dt: tegra20: Rename "gart" to "iommu"
ARM: tegra: move serial clock-frequency attr into the Tegra30 dtsi
ARM: tegra: Add Toradex Iris carrier board DT with T20 512MB COM
ARM: tegra: Add Colibri T20 512MB COM device tree
ARM: tegra: move serial clock-frequency attr into the Tegra20 dtsi
ARM: tegra: harmony: enable keyboard in DT
ARM: tegra: whistler: enable keyboard in DT
ARM: tegra: cardhu: register UARTC
ARM: tegra: seaboard: enable keyboard in DT
ARM: tegra: add DT entry for KBC controller
ARM: tegra: swap cache-/interrupt-ctrlr nodes in DT
ASoC: tegra: add ac97 host controller to device tree
ARM: DT: tegra: Add Tegra30 Beaver board support
ARM: DT: tegra: Add board level compatible properties
ARM: tegra: paz00: enable HDMI port
ARM: tegra: ventana: enable HDMI port
ARM: tegra: seaboard: enable HDMI port
ARM: tegra: trimslice: add gpio-poweroff node to DT
ARM: DT: tegra: Unify the description of Tegra20 boards
...
As reset GPIO information is PHY specific detail, adding
it to PHY DT node.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
No Tegra20 Platform is running PLL_P at another rate than 216MHz, nor is
any using any other PLL as UART source clock. Move attribute into SoC
level dtsi file to slim down board DT files.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable host1x, and the HDMI output. Harmony also has a DVI port with an
HDMI form-factor connector, driven by Tegra's LVDS output. This isn't
enabled yet, due to potential issues with having multiple outputs enabled.
Correct DDC I2C frequency to 100KHz.
Add dummy/fixed regulators to satisfy the HDMI driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
[swarren: add commit description, remove enable of DVI port]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This was accidentally disabled by commit 2a5fdc9 "ARM: dt: tegra:
invert status=disable vs status=okay".
Cc: <stable@vger.kernel.org> # v3.5 (file is named tegra-trimslice.dts there)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On TrimSlice, Tegra's USB1 port may be routed to either an external micro
USB port, or an internal USB->SATA bridge for SSD or HDD. This muxing is
controlled by a GPIO. Whilst not strictly a VBUS GPIO, the TrimSlice
board files caused this GPIO to be set appropriately to enable the SATA
bridge by passing it as the VBUS GPIO to the USB driver. Echo this same
configuration in device tree to enable the SATA bridge.
An alternative might be to implement a full USB bus mux driver. However,
that seems over-complex right now.
Cc: <stable@vger.kernel.org> # v3.5 (file is named tegra-trimslice.dts there)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Most ARM ${board}.dts files are already named ${soc}-${board}.dts. This
change modifies the Tegra board files to be named the same way for
consistency.
Once a related change is made in U-Boot, this will cause both U-Boot and
the kernel to use the same names for the .dts files and SoC identifiers,
thus allowing U-Boot's recently added "soc" and "board" environment
variables to be used to construct the name of Tegra .dtb files, and hence
allow board-generic U-Boot bootcmd scripts to be written.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren