When booting a board that does not have a keypad (such as imx6q-sabresd) the
following error is seen on boot:
imx-keypad 20b8000.kpp: OF: linux,keymap property not defined in /soc/aips-bus@02000000/kpp@020b8000
imx-keypad 20b8000.kpp: failed to build keymap
imx-keypad: probe of 20b8000.kpp failed with error -2
Let's disable the keypad functionality in the dtsi files and let each board dts
enable it when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Spread-spectrum doesn't work with Cubox-i hardware. eSATA devices are
detected, but then fail on normal IO. Therefore, disable this feature.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add the transmit level, boost and attenuation parameters necessary for
the eSATA interface on Cubox-i to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fix usbmisc compatible string so that usbmisc node can be found and USB
functionality can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx6sx iomuxc-gpr syscon is compatible to imx6q, so let's add
compatible string 'fsl,imx6q-iomuxc-gpr' for imx6sx iomuxc-gpr syscon node.
This is necessary to enable SW workaround for ERR007265,
please refer to imx6_pm_common_init of arch/arm/mach-imx/pm-imx6.c
for detail.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch add support for the imx6dl based aristainetos board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
DRAM: 1 GiB
NAND: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
As this board can used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The fixed-regulator's enable-active-high property
is needed to indicate that the GPIO regulator is
active high.
Before that the regulator state was inverted.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The DAI mode is and should be configured by the sound card driver as
codec and ssi have to be in the right modes to communicate with each
other. It is possible to operate the ssi unit or the codec in master mode,
sometimes even on the same board in different configurations.
With the latest changes in the fsl-ssi driver, the 'fsl,mode' property
is only handled as a fallback property. If the sound card sets the DAI
mode correctly, this fallback configuration is dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
All dtsi files where already moved to generic dma bindings. Remove the
old non-generic DMA properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
All imx5*.dtsi files define the generic dma bindings. Drop the old
non-generic fsl,ssi-dma-events.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Replace old ssi dma properties by the generic dma properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The other i.mx6 variants use "vddarm" as the name of the internal regulator
that powers the core. Use the same convention here for consistency.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The S/PDIF rxtx4 and rxtx6 clock inputs are "ESAI_HCKT" and "MLB clock",
respectively, according to the SoC documentation, and they are currently
mapped to clocks "esai" and "mlb".
However, they do not seem to actually work correctly. Testing on a
Cubox-i system with fsl_spdif driver forced to select one of those as
input will result in I/O errors on audio playback, which I believe means
missing clock signal.
Possibly the "ESAI_HCKT" and "MLB clock" refer to some other clocks
related to ESAI and MLB, or we are missing something else.
Since audio playback will not work if fsl_spdif selects these clocks
(which happens rarely), set the inputs do dummy clocks, at least for
now.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The rxtx2 clock of i.MX6 S/PDIF is currently set to "asrc" clock.
However, according to SoC documentation, rxtx2 is connected to
ASRC_EXT_CLK, a different external clock.
Testing on Cubox-i system seems to confirm that: when fsl_spdif is
forced to select rxtx2 as input clock, audio playback fails with an I/O
error.
Set rxtx2 to the dummy clock by default to prevent fsl_spdif from
selecting it.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for the Ka-Ro electronics GmbH TX6 modules.
There are five distinct module types with either i.MX6Q or i.MX6DL and
LVDS or LCD display interface and one DTS file for a complete system
with an i.MX6DL based TX6 module and a baseboard mounted on the back
of a display (imx6dl-tx6dl-comtft.dts).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds CSI subnodes for IPU1 and IPU2 that will contain
ports and endpoints connecting to external elements in the video
pipeline.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The 2.5V VDD_ETH_IO voltage supplied by the DA9063 LDO4 is used
to power the KSZ9031 PHY DVDDH input and to pull the necessary
pins (including bootstrap pins) high.
It also powers the i.MX6 NVCC_RGMII and NVCC_ENET inputs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The imx6dl dts supports both DualLite and Solo CPU variants
The imx6q dts supports both Dual and Quad CPU variants
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common and
not baseboard specific.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The PWM3 pinmux configuration conflicts with gpio 3.28. Introduce a regulator
for mmc0 so that it conflicts with the pwm driver and fails gracefully. The
kernel will then able to access mmc0 normally.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
GPIO4_9 is used as ECSPI1 chip select and it needs to be configured as GPIO.
Configure the pin functionality explicitly in the dts file instead of relying
on the fact that it comes configured as GPIO from POR or from the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for the cpuimx27 board from Eukrea and its
baseboard. This change is intended to further remove non-DT support
for this board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Extend the clock control for FlexCAN with the second gate which
enable the clocks in the Clock Divider (CCM_CSCDR2) register too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Most peripherals on the i.MX53 have an
Off-Platform Peripheral Access Control Register (OPACR)
in which the access rights (together with the MPROT registers) can be declared.
However, this does not seem to work for example for SSI1+SDMA, because the
supervisor bit is not set for the SDMA unit.
It does work for SSI2, the QSB for example uses SSI2 for its audio. But SSI2 only
works because it does NOT have an OPACR.
The right solution would be to fix the access rights for the SDMA, but the unit
responsible for this is the Central Security Unit (CSU), which of course is NOT
documented. So, until documentation for this is openly available, turn off the
supervisor protection because it cripples the hardware.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The i.MX SoCs allow to setup fine grained access rights to peripherals on the
AIPS bus.
This is done via the Peripheral Access Register (PAR) in e.g. the i.MX21
or in later SoC versions the Off-Platform Peripheral Access Control Register
(OPACR), e.g. i.MX53.
Under certain circumstances this leads to problems in which bus masters are
not granted their access rights to peripherals.
To be able to disable these restrictions on DT platforms, add a helper function
that looks for AIPS nodes in the DT and disables them for every compatible node
it finds.
The compatible has to be declared in the mach-specific entry file, where this
helper function should then be called.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch removes definitions which not used anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Use clock defines in order to make devicetrees more human readable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The board has no insufficient support to be fully functional and seems
has no users. This patch removes support for this board.
However, the support may be added in the future by using the devicetree.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch removes excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27.
Instead we use SOC_IMX*.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
i.MX1 camera driver has been removed by the commit 90b055898e.
This patch removes remaining support files for this camera.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
imx6q_pm_enter calls imx6sl_set_wait_clk when run on an imx6sl
based machine. However if support for imx6sl is not enabled
at compile time, this prevents us from building the kernel and
we get this link error instead:
arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
:(.text+0x4b84): undefined reference to `imx6sl_set_wait_clk'
This makes the cpu_is_imx6sl function conditionally return false
if imx6sl is disabled at compile-time, which matches what the
older cpu_is_mx* macros did. We have similar inline functions for
the other imx6 variants, but so far I have not run into a case
where the extra #ifdef is necessary.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Building a kernel for imx6sx but without imx6q support results in
this link error because of the missing cpuidle driver:
arch/arm/mach-imx/built-in.o: In function `imx6sx_init_late'::(.init.text+0xc228):
undefined reference to `imx6q_cpuidle_init'
This patch adds a Makefile entry so we always build support for
the imx6q_cpuidle code when at least one of the 6sx or 6q variants
are enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The PL310 integrated on i.MX6 series and VF610 are revision r3p1 and
later. Per ARM PL310 errata document, 588369 is fixed in r2p0 and
727915 is fixed in r3p1. Neither is needed for i.MX6 or VF610. So
let's drop them.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add EDMA for DMA support for Vybrid SoCs. Also add printk time.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fabio Estevam