Random improvements for sb1250: Silence compiler warnings, a bugfix for
the profiling code, and a comment typo.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix compilation for bcm1480, a hpt is only available on sb1250/bcm112x.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Historically plat_mem_setup did the entire platform initialization. This
was rather impractical because it meant plat_mem_setup had to get away
without any kind of memory allocator. To keep old code from breaking
plat_setup was just renamed to plat_setup and a second platform
initialization hook for anything else was introduced.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Running a UP kernel on a bcm1480 board, I get nonsensical timing
results, like this:
release@unknown:~/tmp$ time ./a.out
real 0m22.906s
user 0m45.792s
sys 0m0.010s
According to my watch, this program took 23 seconds to run, so the real
time clock is OK. It is process accounting that is broken.
I tracked this down to a problem with the function
bcm1480_timer_interrupt in the file sibyte/bcm1480/time.c. This
function calls ll_timer_interrupt for cpu0, and ll_local_timer_interrupt
for all cpus. However, both of these functions do process accounting.
Thus processes running on cpu0 end up with doubled times. This is very
obvious in a UP kernel where all processes run on cpu0.
The correct way to do this is to only call ll_local_timer interrupt if
this is not cpu0. This can be seen in the mips-board/generic/time.c
file, and also in the sibyte/sb1250/time.c file, both of which handle
this correctly. I fixed the bcm1480/time.c file by copying over the
correct code from the sb1250/time.c file.
With this fix, I now get sensible results.
release@unknown:~/tmp$ time ./a.out
real 0m22.903s
user 0m22.894s
sys 0m0.006s
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Saves like 1,600 lines of code, is way easier to debug, compilers
frequently do a better job than the cut and paste type of handlers many
boards had. And finally having all the stuff done in a single place
also means alot of bug potencial for the MT ASE is gone.
The only surviving handler in assembler is the DECstation one; I hope
Maciej will rewrite it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>:
sb1250_gettimeoffset() simply reads the current cpu 0 timer remaining
value, however once this counter reaches 0 and the interrupt is raised,
it immediately resets and begins to count down again.
If sb1250_gettimeoffset() is called on cpu 1 via do_gettimeofday() after
the timer has reset but prior to cpu 0 processing the interrupt and
taking write_seqlock() in timer_interrupt() it will return a full value
(or close to it) causing time to jump backwards 1ms. Once cpu 0 handles
the interrupt and timer_interrupt() gets far enough along it will jump
forward 1ms.
Fix this problem by implementing mips_hpt_*() on sb1250 using a spare
timer unrelated to the existing periodic interrupt timers. It runs at
1Mhz with a full 23bit counter. This eliminated the custom
do_gettimeoffset() for sb1250 and allowed use of the generic
fixed_rate_gettimeoffset() using mips_hpt_*() and timerhi/timerlo.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
From Dave Johnson <djohnson+linuxmips@sw.starentnetworks.com>:
The timers need to be loaded with 1 less than the desired interval not
the interval itself.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A recent change requires cpu_possible_map to be initialized before
smp_sched_init() but most MIPS platforms were initializing their
processors in the prom_prepare_cpus callback of smp_prepare_cpus. The
simple fix of calling prom_prepare_cpus from one of the earlier SMP
initialization hooks doesn't work well either since IPIs may require
init_IRQ() to have completed, so bit the bullet and split
prom_prepare_cpus into two initialization functions, plat_smp_setup
which is called early from setup_arch and plat_prepare_cpus called where
prom_prepare_cpus used to be called.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the following compiler warnings:
CC arch/mips/sibyte/bcm1480/irq.o
arch/mips/sibyte/bcm1480/irq.c: In function ‘bcm1480_set_affinity’:
arch/mips/sibyte/bcm1480/irq.c:168: warning: ISO C90 forbids mixed declarations and code
arch/mips/sibyte/bcm1480/irq.c: In function ‘ack_bcm1480_irq’:
arch/mips/sibyte/bcm1480/irq.c:230: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Many RTC routines were not protected against each other, so there are
potential races, for example, ntp-update against /dev/rtc. This patch
fixes them using rtc_lock.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Kconfig and Makefile changes
- arch/mips/sibyte/bcm1480/
- changes to sibyte common code to support 1480
Signed-Off-By: Andy Isaacson <adi@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Thiemo Seufer