mirror of https://gitee.com/openkylin/linux.git
425 Commits
Author | SHA1 | Message | Date |
---|---|---|---|
Linus Torvalds | 133d970e0d |
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle: "This is the main MIPS pull request for 4.9: MIPS core arch code: - traps: 64bit kernels should read CP0_EBase 64bit - traps: Convert ebase to KSEG0 - c-r4k: Drop bc_wback_inv() from icache flush - c-r4k: Split user/kernel flush_icache_range() - cacheflush: Use __flush_icache_user_range() - uprobes: Flush icache via kernel address - KVM: Use __local_flush_icache_user_range() - c-r4k: Fix flush_icache_range() for EVA - Fix -mabi=64 build of vdso.lds - VDSO: Drop duplicated -I*/-E* aflags - tracing: move insn_has_delay_slot to a shared header - tracing: disable uprobe/kprobe on compact branch instructions - ptrace: Fix regs_return_value for kernel context - Squash lines for simple wrapper functions - Move identification of VP(E) into proc.c from smp-mt.c - Add definitions of SYNC barrierstype values - traps: Ensure full EBase is written - tlb-r4k: If there are wired entries, don't use TLBINVF - Sanitise coherentio semantics - dma-default: Don't check hw_coherentio if device is non-coherent - Support per-device DMA coherence - Adjust MIPS64 CAC_BASE to reflect Config.K0 - Support generating Flattened Image Trees (.itb) - generic: Introduce generic DT-based board support - generic: Convert SEAD-3 to a generic board - Enable hardened usercopy - Don't specify STACKPROTECTOR in defconfigs Octeon: - Delete dead code and files across the platform. - Change to use all memory into use by default. - Rename upper case variables in setup code to lowercase. - Delete legacy hack for broken bootloaders. - Leave maintaining the link state to the actual ethernet/PHY drivers. - Add DTS for D-Link DSR-500N. - Fix PCI interrupt routing on D-Link DSR-500N. Pistachio: - Remove ANDROID_TIMED_OUTPUT from defconfig TX39xx: - Move GPIO setup from .mem_setup() to .arch_init() - Convert to Common Clock Framework TX49xx: - Move GPIO setup from .mem_setup() to .arch_init() - Convert to Common Clock Framework txx9wdt: - Add missing clock (un)prepare calls for CCF BMIPS: - Add PW, GPIO SDHCI and NAND device node names - Support APPENDED_DTB - Add missing bcm97435svmb to DT_NONE - Rename bcm96358nb4ser to bcm6358-neufbox4-sercom - Add DT examples for BCM63268, BCM3368 and BCM6362 - Add support for BCM3368 and BCM6362 PCI - Reduce stack frame usage - Use struct list_head lists - Support for CONFIG_PCI_DOMAINS_GENERIC - Make pcibios_set_cache_line_size an initcall - Inline pcibios_assign_all_busses - Split pci.c into pci.c & pci-legacy.c - Introduce CONFIG_PCI_DRIVERS_LEGACY - Support generic drivers CPC - Convert bare 'unsigned' to 'unsigned int' - Avoid lock when MIPS CM >= 3 is present GIC: - Delete unused file smp-gic.c mt7620: - Delete unnecessary assignment for the field "owner" from PCI BCM63xx: - Let clk_disable() return immediately if clk is NULL pm-cps: - Change FSB workaround to CPU blacklist - Update comments on barrier instructions - Use MIPS standard lightweight ordering barrier - Use MIPS standard completion barrier - Remove selection of sync types - Add MIPSr6 CPU support - Support CM3 changes to Coherence Enable Register SMP: - Wrap call to mips_cpc_lock_other in mips_cm_lock_other - Introduce mechanism for freeing and allocating IPIs cpuidle: - cpuidle-cps: Enable use with MIPSr6 CPUs. SEAD3: - Rewrite to use DT and generic kernel feature. USB: - host: ehci-sead3: Remove SEAD-3 EHCI code FBDEV: - cobalt_lcdfb: Drop SEAD3 support dt-bindings: - Document a binding for simple ASCII LCDs auxdisplay: - img-ascii-lcd: driver for simple ASCII LCD displays irqchip i8259: - i8259: Add domain before mapping parent irq - i8259: Allow platforms to override poll function - i8259: Remove unused i8259A_irq_pending Malta: - Rewrite to use DT of/platform: - Probe "isa" busses by default CM: - Print CM error reports upon bus errors Module: - Migrate exception table users off module.h and onto extable.h - Make various drivers explicitly non-modular: - Audit and remove any unnecessary uses of module.h mailmap: - Canonicalize to Qais' current email address. Documentation: - MIPS supports HAVE_REGS_AND_STACK_ACCESS_API Loongson1C: - Add CPU support for Loongson1C - Add board support - Add defconfig - Add RTC support for Loongson1C board All this except one Documentation fix has sat in linux-next and has survived Imagination's automated build test system" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits) Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API MIPS: ptrace: Fix regs_return_value for kernel context MIPS: VDSO: Drop duplicated -I*/-E* aflags MIPS: Fix -mabi=64 build of vdso.lds MIPS: Enable hardened usercopy MIPS: generic: Convert SEAD-3 to a generic board MIPS: generic: Introduce generic DT-based board support MIPS: Support generating Flattened Image Trees (.itb) MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0 MIPS: Print CM error reports upon bus errors MIPS: Support per-device DMA coherence MIPS: dma-default: Don't check hw_coherentio if device is non-coherent MIPS: Sanitise coherentio semantics MIPS: PCI: Support generic drivers MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY MIPS: PCI: Split pci.c into pci.c & pci-legacy.c MIPS: PCI: Inline pcibios_assign_all_busses MIPS: PCI: Make pcibios_set_cache_line_size an initcall MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC MIPS: PCI: Use struct list_head lists ... |
|
Chris Metcalf | 6727ad9e20 |
nmi_backtrace: generate one-line reports for idle cpus
When doing an nmi backtrace of many cores, most of which are idle, the output is a little overwhelming and very uninformative. Suppress messages for cpus that are idling when they are interrupted and just emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN". We do this by grouping all the cpuidle code together into a new .cpuidle.text section, and then checking the address of the interrupted PC to see if it lies within that section. This commit suitably tags x86 and tile idle routines, and only adds in the minimal framework for other architectures. Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm] Tested-by: Petr Mladek <pmladek@suse.com> Cc: Aaron Tomlin <atomlin@redhat.com> Cc: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Russell King <linux@arm.linux.org.uk> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> |
|
Matt Redfearn | 72bc8c75ea |
cpuidle: cpuidle-cps: Enable use with MIPSr6 CPUs.
This patch enables the MIPS CPS driver for MIPSr6 CPUs. Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Rafael J. Wysocki <rjw@rjwysocki.net> Cc: linux-mips@linux-mips.org Cc: linux-pm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/14228/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> |
|
Linus Torvalds | 597f03f9d1 |
Merge branch 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Thomas Gleixner: "Yet another batch of cpu hotplug core updates and conversions: - Provide core infrastructure for multi instance drivers so the drivers do not have to keep custom lists. - Convert custom lists to the new infrastructure. The block-mq custom list conversion comes through the block tree and makes the diffstat tip over to more lines removed than added. - Handle unbalanced hotplug enable/disable calls more gracefully. - Remove the obsolete CPU_STARTING/DYING notifier support. - Convert another batch of notifier users. The relayfs changes which conflicted with the conversion have been shipped to me by Andrew. The remaining lot is targeted for 4.10 so that we finally can remove the rest of the notifiers" * 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits) cpufreq: Fix up conversion to hotplug state machine blk/mq: Reserve hotplug states for block multiqueue x86/apic/uv: Convert to hotplug state machine s390/mm/pfault: Convert to hotplug state machine mips/loongson/smp: Convert to hotplug state machine mips/octeon/smp: Convert to hotplug state machine fault-injection/cpu: Convert to hotplug state machine padata: Convert to hotplug state machine cpufreq: Convert to hotplug state machine ACPI/processor: Convert to hotplug state machine virtio scsi: Convert to hotplug state machine oprofile/timer: Convert to hotplug state machine block/softirq: Convert to hotplug state machine lib/irq_poll: Convert to hotplug state machine x86/microcode: Convert to hotplug state machine sh/SH-X3 SMP: Convert to hotplug state machine ia64/mca: Convert to hotplug state machine ARM/OMAP/wakeupgen: Convert to hotplug state machine ARM/shmobile: Convert to hotplug state machine arm64/FP/SIMD: Convert to hotplug state machine ... |
|
Rafael J. Wysocki | e35db92b4f |
Merge branches 'pm-cpuidle', 'pm-opp' and 'pm-avs'
* pm-cpuidle: ARM: cpuidle: Fix error return code * pm-opp: PM / OPP: Don't support OPP if it provides supported-hw but platform does not PM / OPP: avoid maybe-uninitialized warning * pm-avs: PM / AVS: SmartReflex: Neaten logging |
|
Sebastian Andrzej Siewior | dfc616d8b3 |
cpuidle/coupled: Convert to hotplug state machine
Install the callbacks via the state machine. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: linux-pm@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20160824091444.brdr5zpbxjvh6n3f@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> |
|
Sebastian Andrzej Siewior | 10fcca9d87 |
cpuidle/powernv: Convert to hotplug state machine
Install the callbacks via the state machine. v1…v2: - Use only CPUHP_CPUIDLE_DEAD (requested by Daniel Lezcano) Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: linux-pm@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20160824091259.ozyslcopxvbfdqzy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> |
|
Sebastian Andrzej Siewior | 529351fd3c |
cpuidle/pseries: Convert to hotplug state machine
Install the callbacks via the state machine. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: linux-pm@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20160818125731.27256-11-bigeasy@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de> |
|
Christophe Jaillet | af48d7bc37 |
ARM: cpuidle: Fix error return code
We know that 'ret = 0' because it has been tested a few lines above.
So, if 'kzalloc' fails, 0 will be returned instead of an error code.
Return -ENOMEM instead.
Fixes:
|
|
Linus Torvalds | bad60e6f25 |
powerpc updates for 4.8 # 1
Highlights: - PowerNV PCI hotplug support. - Lots more Power9 support. - eBPF JIT support on ppc64le. - Lots of cxl updates. - Boot code consolidation. Bug fixes: - Fix spin_unlock_wait() from Boqun Feng - Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling - Fix multiple bugs in memory_hotplug_max() from Bharata B Rao - mm: Ensure "special" zones are empty from Oliver O'Halloran - ftrace: Separate the heuristics for checking call sites from Michael Ellerman - modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman - Fix endianness when reading TCEs from Alexey Kardashevskiy - start rtasd before PCI probing from Greg Kurz - PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler - powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu Cleanups & fixes: - Drop support for MPIC in pseries from Rashmica Gupta - Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman - Remove unused symbols in asm-offsets.c from Rashmica Gupta - Fix SRIOV not building without EEH enabled from Russell Currey - Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann - Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt - Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh - Avoid -maltivec when using clang integrated assembler from Anton Blanchard - Fix array overrun in ppc_rtas() syscall from Andrew Donnellan - Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes - export cpu_to_core_id() from Mauricio Faria de Oliveira - Remove old symbols from defconfigs from Andrew Donnellan - Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt - Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt - Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao - Remove RELOCATABLE_PPC32 from Kevin Hao - Fix .long's in tlb-radix.c to more meaningful from Balbir Singh Minor cleanups & fixes: - Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman, Stephen Rothwell, Stewart Smith. Freescale updates from Scott: - "Highlights include more 8xx optimizations, device tree updates, and MVME7100 support." PowerNV PCI hotplug from Gavin Shan: - PCI: Add pcibios_setup_bridge() - Override pcibios_setup_bridge() - Remove PCI_RESET_DELAY_US - Move pnv_pci_ioda_setup_opal_tce_kill() around - Increase PE# capacity - Allocate PE# in reverse order - Create PEs in pcibios_setup_bridge() - Setup PE for root bus - Extend PCI bridge resources - Make pnv_ioda_deconfigure_pe() visible - Dynamically release PE - Update bridge windows on PCI plug - Delay populating pdn - Support PCI slot ID - Use PCI slot reset infrastructure - Introduce pnv_pci_get_slot_id() - Functions to get/set PCI slot state - PCI/hotplug: PowerPC PowerNV PCI hotplug driver - Print correct PHB type names Power9 idle support from Shreyas B. Prabhu: - set power_save func after the idle states are initialized - Use PNV_THREAD_WINKLE macro while requesting for winkle - make hypervisor state restore a function - Rename idle_power7.S to idle_book3s.S - Rename reusable idle functions to hardware agnostic names - Make pnv_powersave_common more generic - abstraction for saving SPRs before entering deep idle states - Add platform support for stop instruction - cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES - cpuidle/powernv: cleanup cpuidle-powernv.c - cpuidle/powernv: Add support for POWER ISA v3 idle states - Use deepest stop state when cpu is offlined Power9 PMU from Madhavan Srinivasan: - factor out power8 pmu macros and defines - factor out power8 pmu functions - factor out power8 __init_pmu code - Add power9 event list macros for generic and cache events - Power9 PMU support - Export Power9 generic and cache events to sysfs Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt: - Add XICS emulation APIs - Move a few exception common handlers to make room - Add support for HV virtualization interrupts - Add mechanism to force a replay of interrupts - Add ICP OPAL backend - Discover IODA3 PHBs - pci: Remove obsolete SW invalidate - opal: Add real mode call wrappers - Rename TCE invalidation calls - Remove SWINV constants and obsolete TCE code - Rework accessing the TCE invalidate register - Fallback to OPAL for TCE invalidations - Use the device-tree to get available range of M64's - Check status of a PHB before using it - pci: Don't try to allocate resources that will be reassigned Other Power9: - Send SIGBUS on unaligned copy and paste from Chris Smart - Large Decrementer support from Oliver O'Halloran - Load Monitor Register Support from Jack Miller Performance improvements from Anton Blanchard: - Avoid load hit store in __giveup_fpu() and __giveup_altivec() - Avoid load hit store in setup_sigcontext() - Remove assembly versions of strcpy, strcat, strlen and strcmp - Align hot loops of some string functions eBPF JIT from Naveen N. Rao: - Fix/enhance 32-bit Load Immediate implementation - Optimize 64-bit Immediate loads - Introduce rotate immediate instructions - A few cleanups - Isolate classic BPF JIT specifics into a separate header - Implement JIT compiler for extended BPF Operator Panel driver from Suraj Jitindar Singh: - devicetree/bindings: Add binding for operator panel on FSP machines - Add inline function to get rc from an ASYNC_COMP opal_msg - Add driver for operator panel on FSP machines Sparse fixes from Daniel Axtens: - make some things static - Introduce asm-prototypes.h - Include headers containing prototypes - Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE - kvm: Clarify __user annotations - Pass endianness to sparse - Make ppc_md.{halt, restart} __noreturn MM fixes & cleanups from Aneesh Kumar K.V: - radix: Update LPCR HR bit as per ISA - use _raw variant of page table accessors - Compile out radix related functions if RADIX_MMU is disabled - Clear top 16 bits of va only on older cpus - Print formation regarding the the MMU mode - hash: Update SDR1 size encoding as documented in ISA 3.0 - radix: Update PID switch sequence - radix: Update machine call back to support new HCALL. - radix: Add LPID based tlb flush helpers - radix: Add a kernel command line to disable radix - Cleanup LPCR defines Boot code consolidation from Benjamin Herrenschmidt: - Move epapr_paravirt_early_init() to early_init_devtree() - cell: Don't use flat device-tree after boot - ge_imp3a: Don't use the flat device-tree after boot - mpc85xx_ds: Don't use the flat device-tree after boot - mpc85xx_rdb: Don't use the flat device-tree after boot - Don't test for machine type in rtas_initialize() - Don't test for machine type in smp_setup_cpu_maps() - dt: Add of_device_compatible_match() - Factor do_feature_fixup calls - Move 64-bit feature fixup earlier - Move 64-bit memory reserves to setup_arch() - Use a cachable DART - Move FW feature probing out of pseries probe() - Put exception configuration in a common place - Remove early allocation of the SMU command buffer - Move MMU backend selection out of platform code - pasemi: Remove IOBMAP allocation from platform probe() - mm/hash: Don't use machine_is() early during boot - Don't test for machine type to detect HEA special case - pmac: Remove spurrious machine type test - Move hash table ops to a separate structure - Ensure that ppc_md is empty before probing for machine type - Move 64-bit probe_machine() to later in the boot process - Move 32-bit probe() machine to later in the boot process - Get rid of ppc_md.init_early() - Move the boot time info banner to a separate function - Move setting of {i,d}cache_bsize to initialize_cache_info() - Move the content of setup_system() to setup_arch() - Move cache info inits to a separate function - Re-order the call to smp_setup_cpu_maps() - Re-order setup_panic() - Make a few boot functions __init - Merge 32-bit and 64-bit setup_arch() Other new features: - tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas - tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas - powerpc: Add module autoloading based on CPU features from Alastair D'Silva - crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva - Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt - xmon: Dump ISA 2.06 SPRs from Michael Ellerman - xmon: Dump ISA 2.07 SPRs from Michael Ellerman - Add a parameter to disable 1TB segs from Oliver O'Halloran - powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran - Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli - pseries: Add pseries hotplug workqueue from John Allen - pseries: Add support for hotplug interrupt source from John Allen - pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen - pseries: Move property cloning into its own routine from Nathan Fontenot - pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot - pseries: Auto-online hotplugged memory from Nathan Fontenot - pseries: Remove call to memblock_add() from Nathan Fontenot cxl: - Add set and get private data to context struct from Michael Neuling - make base more explicitly non-modular from Paul Gortmaker - Use for_each_compatible_node() macro from Wei Yongjun - Frederic Barrat - Abstract the differences between the PSL and XSL - Make vPHB device node match adapter's - Philippe Bergheaud - Add mechanism for delivering AFU driver specific events - Ignore CAPI adapters misplaced in switched slots - Refine slice error debug messages - Andrew Donnellan - static-ify variables to fix sparse warnings - PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl - PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state - Add cxl_check_and_switch_mode() API to switch bi-modal cards - remove dead Kconfig options - fix potential NULL dereference in free_adapter() - Ian Munsie - Update process element after allocating interrupts - Add support for CAPP DMA mode - Fix allowing bogus AFU descriptors with 0 maximum processes - Fix allocating a minimum of 2 pages for the SPA - Fix bug where AFU disable operation had no effect - Workaround XSL bug that does not clear the RA bit after a reset - Fix NULL pointer dereference on kernel contexts with no AFU interrupts - powerpc/powernv: Split cxl code out into a separate file - Add cxl_slot_is_supported API - Enable bus mastering for devices using CAPP DMA mode - Move cxl_afu_get / cxl_afu_put to base - Allow a default context to be associated with an external pci_dev - Do not create vPHB if there are no AFU configuration records - powerpc/powernv: Add support for the cxl kernel api on the real phb - Add support for using the kernel API with a real PHB - Add kernel APIs to get & set the max irqs per context - Add preliminary workaround for CX4 interrupt limitation - Add support for interrupts on the Mellanox CX4 - Workaround PE=0 hardware limitation in Mellanox CX4 - powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n selftests: - Test unaligned copy and paste from Chris Smart - Load Monitor Register Tests from Jack Miller - Cyril Bur - exec() with suspended transaction - Use signed long to read perf_event_paranoid - Fix usage message in context_switch - Fix generation of vector instructions/types in context_switch - Michael Ellerman - Use "Delta" rather than "Error" in normal output - Import Anton's mmap & futex micro benchmarks - Add a test for PROT_SAO -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJXnWchAAoJEFHr6jzI4aWAe64P/36Vd9yJLptjkoyZp8/IQtu1 Cv8buQwGdKuSMzdkcUAOXcC3fe2u70ZWXMKKLfY3koIV1IAiqdWk5/XWRKMP2XmE dG0LhSf0uu7uh+mE0WvQnRu46ImeKtQ+mPp4Hbs/s9SxMSeYjruv3vdWWmgUq0cl Gac2qJSRtAMmgLuHWMjf7N5mxOTOnKejU4o2i9cJ+YHmWKOdCigv2Ge1UadOQFlC E7tRPiUR3asfDfj+e+LVTTdToH6p8pk+mOUzIoZ8jIkQ+IXzi62UDl5+Rw9mqiuX 1CtqEMUXxo2qwX+d4TcV/QUOp0YKPuIcUZ9NMMS+S3lOyJ4NFt+j2Izk7QJp5kNP gKVqB68TjDQsBuDr3P9ynlHbduxTIhZAqopbTrLe0FIg48nUe4n1yHJBVzqaVajX rFBJSsSUffBLAARNPSXJJhIgc2C1/qOC8dgMeDMcR2kPirDHaQZ/lY1yEpq1yiqR q6e3v5hvIAm4IjbYk0mF7TUxBrPGVE/ExyBINyASRoYxAJ1PyeD/iljZ9vI3asRA s+hhxT8H3f7lnqTrmJqMjHgAdGkmag07EdmvFNX4xK4aADSy7Y6g4dw25ffRopo9 p9Jf9HX+dZv65Y3UjbV/6HuXcaSEBJJLSVWvii65PebqSN0LuHEFvNeIJ6Iblx0B AWh/hd0Iin2gdkcG39Mr =Z5kM -----END PGP SIGNATURE----- Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc updates from Michael Ellerman: "Highlights: - PowerNV PCI hotplug support. - Lots more Power9 support. - eBPF JIT support on ppc64le. - Lots of cxl updates. - Boot code consolidation. Bug fixes: - Fix spin_unlock_wait() from Boqun Feng - Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling - Fix multiple bugs in memory_hotplug_max() from Bharata B Rao - mm: Ensure "special" zones are empty from Oliver O'Halloran - ftrace: Separate the heuristics for checking call sites from Michael Ellerman - modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman - Fix endianness when reading TCEs from Alexey Kardashevskiy - start rtasd before PCI probing from Greg Kurz - PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler - powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu Cleanups & fixes: - Drop support for MPIC in pseries from Rashmica Gupta - Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman - Remove unused symbols in asm-offsets.c from Rashmica Gupta - Fix SRIOV not building without EEH enabled from Russell Currey - Remove kretprobe_trampoline_holder from Thiago Jung Bauermann - Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt - Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh - Avoid -maltivec when using clang integrated assembler from Anton Blanchard - Fix array overrun in ppc_rtas() syscall from Andrew Donnellan - Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes - export cpu_to_core_id() from Mauricio Faria de Oliveira - Remove old symbols from defconfigs from Andrew Donnellan - Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt - Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt - Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao - Remove RELOCATABLE_PPC32 from Kevin Hao - Fix .long's in tlb-radix.c to more meaningful from Balbir Singh Minor cleanups & fixes: - Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman, Stephen Rothwell, Stewart Smith. Freescale updates from Scott: - "Highlights include more 8xx optimizations, device tree updates, and MVME7100 support." PowerNV PCI hotplug from Gavin Shan: - PCI: Add pcibios_setup_bridge() - Override pcibios_setup_bridge() - Remove PCI_RESET_DELAY_US - Move pnv_pci_ioda_setup_opal_tce_kill() around - Increase PE# capacity - Allocate PE# in reverse order - Create PEs in pcibios_setup_bridge() - Setup PE for root bus - Extend PCI bridge resources - Make pnv_ioda_deconfigure_pe() visible - Dynamically release PE - Update bridge windows on PCI plug - Delay populating pdn - Support PCI slot ID - Use PCI slot reset infrastructure - Introduce pnv_pci_get_slot_id() - Functions to get/set PCI slot state - PCI/hotplug: PowerPC PowerNV PCI hotplug driver - Print correct PHB type names Power9 idle support from Shreyas B. Prabhu: - set power_save func after the idle states are initialized - Use PNV_THREAD_WINKLE macro while requesting for winkle - make hypervisor state restore a function - Rename idle_power7.S to idle_book3s.S - Rename reusable idle functions to hardware agnostic names - Make pnv_powersave_common more generic - abstraction for saving SPRs before entering deep idle states - Add platform support for stop instruction - cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES - cpuidle/powernv: cleanup cpuidle-powernv.c - cpuidle/powernv: Add support for POWER ISA v3 idle states - Use deepest stop state when cpu is offlined Power9 PMU from Madhavan Srinivasan: - factor out power8 pmu macros and defines - factor out power8 pmu functions - factor out power8 __init_pmu code - Add power9 event list macros for generic and cache events - Power9 PMU support - Export Power9 generic and cache events to sysfs Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt: - Add XICS emulation APIs - Move a few exception common handlers to make room - Add support for HV virtualization interrupts - Add mechanism to force a replay of interrupts - Add ICP OPAL backend - Discover IODA3 PHBs - pci: Remove obsolete SW invalidate - opal: Add real mode call wrappers - Rename TCE invalidation calls - Remove SWINV constants and obsolete TCE code - Rework accessing the TCE invalidate register - Fallback to OPAL for TCE invalidations - Use the device-tree to get available range of M64's - Check status of a PHB before using it - pci: Don't try to allocate resources that will be reassigned Other Power9: - Send SIGBUS on unaligned copy and paste from Chris Smart - Large Decrementer support from Oliver O'Halloran - Load Monitor Register Support from Jack Miller Performance improvements from Anton Blanchard: - Avoid load hit store in __giveup_fpu() and __giveup_altivec() - Avoid load hit store in setup_sigcontext() - Remove assembly versions of strcpy, strcat, strlen and strcmp - Align hot loops of some string functions eBPF JIT from Naveen N. Rao: - Fix/enhance 32-bit Load Immediate implementation - Optimize 64-bit Immediate loads - Introduce rotate immediate instructions - A few cleanups - Isolate classic BPF JIT specifics into a separate header - Implement JIT compiler for extended BPF Operator Panel driver from Suraj Jitindar Singh: - devicetree/bindings: Add binding for operator panel on FSP machines - Add inline function to get rc from an ASYNC_COMP opal_msg - Add driver for operator panel on FSP machines Sparse fixes from Daniel Axtens: - make some things static - Introduce asm-prototypes.h - Include headers containing prototypes - Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE - kvm: Clarify __user annotations - Pass endianness to sparse - Make ppc_md.{halt, restart} __noreturn MM fixes & cleanups from Aneesh Kumar K.V: - radix: Update LPCR HR bit as per ISA - use _raw variant of page table accessors - Compile out radix related functions if RADIX_MMU is disabled - Clear top 16 bits of va only on older cpus - Print formation regarding the the MMU mode - hash: Update SDR1 size encoding as documented in ISA 3.0 - radix: Update PID switch sequence - radix: Update machine call back to support new HCALL. - radix: Add LPID based tlb flush helpers - radix: Add a kernel command line to disable radix - Cleanup LPCR defines Boot code consolidation from Benjamin Herrenschmidt: - Move epapr_paravirt_early_init() to early_init_devtree() - cell: Don't use flat device-tree after boot - ge_imp3a: Don't use the flat device-tree after boot - mpc85xx_ds: Don't use the flat device-tree after boot - mpc85xx_rdb: Don't use the flat device-tree after boot - Don't test for machine type in rtas_initialize() - Don't test for machine type in smp_setup_cpu_maps() - dt: Add of_device_compatible_match() - Factor do_feature_fixup calls - Move 64-bit feature fixup earlier - Move 64-bit memory reserves to setup_arch() - Use a cachable DART - Move FW feature probing out of pseries probe() - Put exception configuration in a common place - Remove early allocation of the SMU command buffer - Move MMU backend selection out of platform code - pasemi: Remove IOBMAP allocation from platform probe() - mm/hash: Don't use machine_is() early during boot - Don't test for machine type to detect HEA special case - pmac: Remove spurrious machine type test - Move hash table ops to a separate structure - Ensure that ppc_md is empty before probing for machine type - Move 64-bit probe_machine() to later in the boot process - Move 32-bit probe() machine to later in the boot process - Get rid of ppc_md.init_early() - Move the boot time info banner to a separate function - Move setting of {i,d}cache_bsize to initialize_cache_info() - Move the content of setup_system() to setup_arch() - Move cache info inits to a separate function - Re-order the call to smp_setup_cpu_maps() - Re-order setup_panic() - Make a few boot functions __init - Merge 32-bit and 64-bit setup_arch() Other new features: - tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas - tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas - powerpc: Add module autoloading based on CPU features from Alastair D'Silva - crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva - Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt - xmon: Dump ISA 2.06 SPRs from Michael Ellerman - xmon: Dump ISA 2.07 SPRs from Michael Ellerman - Add a parameter to disable 1TB segs from Oliver O'Halloran - powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran - Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli - pseries: Add pseries hotplug workqueue from John Allen - pseries: Add support for hotplug interrupt source from John Allen - pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen - pseries: Move property cloning into its own routine from Nathan Fontenot - pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot - pseries: Auto-online hotplugged memory from Nathan Fontenot - pseries: Remove call to memblock_add() from Nathan Fontenot cxl: - Add set and get private data to context struct from Michael Neuling - make base more explicitly non-modular from Paul Gortmaker - Use for_each_compatible_node() macro from Wei Yongjun - Frederic Barrat - Abstract the differences between the PSL and XSL - Make vPHB device node match adapter's - Philippe Bergheaud - Add mechanism for delivering AFU driver specific events - Ignore CAPI adapters misplaced in switched slots - Refine slice error debug messages - Andrew Donnellan - static-ify variables to fix sparse warnings - PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl - PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state - Add cxl_check_and_switch_mode() API to switch bi-modal cards - remove dead Kconfig options - fix potential NULL dereference in free_adapter() - Ian Munsie - Update process element after allocating interrupts - Add support for CAPP DMA mode - Fix allowing bogus AFU descriptors with 0 maximum processes - Fix allocating a minimum of 2 pages for the SPA - Fix bug where AFU disable operation had no effect - Workaround XSL bug that does not clear the RA bit after a reset - Fix NULL pointer dereference on kernel contexts with no AFU interrupts - powerpc/powernv: Split cxl code out into a separate file - Add cxl_slot_is_supported API - Enable bus mastering for devices using CAPP DMA mode - Move cxl_afu_get / cxl_afu_put to base - Allow a default context to be associated with an external pci_dev - Do not create vPHB if there are no AFU configuration records - powerpc/powernv: Add support for the cxl kernel api on the real phb - Add support for using the kernel API with a real PHB - Add kernel APIs to get & set the max irqs per context - Add preliminary workaround for CX4 interrupt limitation - Add support for interrupts on the Mellanox CX4 - Workaround PE=0 hardware limitation in Mellanox CX4 - powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n selftests: - Test unaligned copy and paste from Chris Smart - Load Monitor Register Tests from Jack Miller - Cyril Bur - exec() with suspended transaction - Use signed long to read perf_event_paranoid - Fix usage message in context_switch - Fix generation of vector instructions/types in context_switch - Michael Ellerman - Use "Delta" rather than "Error" in normal output - Import Anton's mmap & futex micro benchmarks - Add a test for PROT_SAO" * tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits) powerpc/mm: Parenthesise IS_ENABLED() in if condition tty/hvc: Use opal irqchip interface if available tty/hvc: Use IRQF_SHARED for OPAL hvc consoles selftests/powerpc: exec() with suspended transaction powerpc: Improve comment explaining why we modify VRSAVE powerpc/mm: Drop unused externs for hpte_init_beat[_v3]() powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header powerpc/mm: Fix build break when PPC_NATIVE=n crypto: vmx - Convert to CPU feature based module autoloading powerpc: Add module autoloading based on CPU features powerpc/powernv/ioda: Fix endianness when reading TCEs powerpc/mm: Add memory barrier in __hugepte_alloc() powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call powerpc/ftrace: Separate the heuristics for checking call sites powerpc: Merge 32-bit and 64-bit setup_arch() powerpc/64: Make a few boot functions __init powerpc: Re-order setup_panic() powerpc: Re-order the call to smp_setup_cpu_maps() powerpc/32: Move cache info inits to a separate function powerpc/64: Move the content of setup_system() to setup_arch() ... |
|
Sudeep Holla | 220276e09b |
cpuidle: introduce CPU_PM_CPU_IDLE_ENTER macro for ARM{32, 64}
The function arm_enter_idle_state is exactly the same in both generic ARM{32,64} CPUIdle driver and will be the same even on ARM64 backend for ACPI processor idle driver. So we can unify it and move it to a common place by introducing CPU_PM_CPU_IDLE_ENTER macro that can be used in all places avoiding duplication. This is in preparation of reuse of the generic cpuidle entry function for ACPI LPI support on ARM64. Suggested-by: Rafael J. Wysocki <rjw@rjwysocki.net> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Shreyas B. Prabhu | 3005c597ba |
cpuidle/powernv: Add support for POWER ISA v3 idle states
POWER ISA v3 defines a new idle processor core mechanism. In summary, a) new instruction named stop is added. b) new per thread SPR named PSSCR is added which controls the behavior of stop instruction. Supported idle states and value to be written to PSSCR register to enter any idle state is exposed via ibm,cpu-idle-state-names and ibm,cpu-idle-state-psscr respectively. To enter an idle state, platform provided power_stop() needs to be invoked with the appropriate PSSCR value. This patch adds support for this new mechanism in cpuidle powernv driver. Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com> Cc: linux-pm@vger.kernel.org Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: linuxppc-dev@lists.ozlabs.org Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> |
|
Shreyas B. Prabhu | 957efcedee |
cpuidle/powernv: cleanup cpuidle-powernv.c
- Use stack instead of kzalloc'ed memory for variables while probing device tree for idle states. - Set cap for number of idle states that can be added to cpuidle_state_table - Minor change in way we check of_property_read_u32_array for error for sake of consistency - Drop unnecessary "&" while assigning function pointer Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: linux-pm@vger.kernel.org Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> |
|
Shreyas B. Prabhu | 169f3fae0c |
cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
Use cpuidle's CPUIDLE_STATE_MAX macro instead of powernv specific MAX_POWERNV_IDLE_STATES. Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: linux-pm@vger.kernel.org Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> |
|
Shreyas B. Prabhu | dbd1b8ea43 |
cpuidle: Fix last_residency division
Snooze is a poll idle state in powernv and pseries platforms. Snooze has a timeout so that if a CPU stays in snooze for more than target residency of the next available idle state, then it would exit thereby giving chance to the cpuidle governor to re-evaluate and promote the CPU to a deeper idle state. Therefore whenever snooze exits due to this timeout, its last_residency will be target_residency of the next deeper state. Commit |
|
Daniel Lezcano | e7387da520 |
cpuidle: Fix cpuidle_state_is_coupled() argument in cpuidle_enter()
Commit |
|
Rafael J. Wysocki | fd7c3c29f9 | Merge back new cpuidle material for v4.7. | |
James Morse | 625fe4f8ff |
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
arm_cpuidle_suspend() may return -EOPNOTSUPP, or any value returned
by the cpu_ops/cpuidle_ops suspend call. arm_enter_idle_state() doesn't
update 'ret' with this value, meaning we always signal success to
cpuidle_enter_state(), causing it to update the usage counters as if we
succeeded.
Fixes:
|
|
Daniel Lezcano | e93e59ce5b |
cpuidle: Replace ktime_get() with local_clock()
The ktime_get() can have a non negligeable overhead, use local_clock() instead. In order to test the difference between ktime_get() and local_clock(), a quick hack has been added to trigger, via debugfs, 10000 times a call to ktime_get() and local_clock() and measure the elapsed time. Then the average value, the min and max is computed for each call. From userspace, the test above was called 100 times every 2 seconds. So, ktime_get() and local_clock() have been called 1000000 times in total. The results are: ktime_get(): ============ * average: 101 ns (stddev: 27.4) * maximum: 38313 ns * minimum: 65 ns local_clock(): ============== * average: 60 ns (stddev: 9.8) * maximum: 13487 ns * minimum: 46 ns The local_clock() is faster and more stable. Even if it is a drop in the ocean, changing the ktime_get() by the local_clock() allows to save 80ns at idle time (entry + exit). And in some circumstances, especially when there are several CPUs racing for the clock access, we save tens of microseconds. The idle duration resulting from a diff is converted from nanosec to microsec. This could be done with integer division (div 1000) - which is an expensive operation or by 10 bits shifting (div 1024) - which is fast but unprecise. The following table gives some results at the limits. ------------------------------------------ | nsec | div(1000) | div(1024) | ------------------------------------------ | 1e3 | 1 usec | 976 nsec | ------------------------------------------ | 1e6 | 1000 usec | 976 usec | ------------------------------------------ | 1e9 | 1000000 usec | 976562 usec | ------------------------------------------ There is a linear deviation of 2.34%. This loss of precision is acceptable in the context of the resulting diff which is used for statistics. These ones are processed to guess estimate an approximation of the duration of the next idle period which ends up into an idle state selection. The selection criteria takes into account the next duration based on large intervals, represented by the idle state's target residency. The 2^10 division is enough because the approximation regarding the 1e3 division is lost in all the approximations done for the next idle duration computation. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> [ rjw: Subject ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Dave Gerlach | c998c07836 |
cpuidle: Indicate when a device has been unregistered
Currently the 'registered' member of the cpuidle_device struct is set
to 1 during cpuidle_register_device. In this same function there are
checks to see if the device is already registered to prevent duplicate
calls to register the device, but this value is never set to 0 even on
unregister of the device. Because of this, any attempt to call
cpuidle_register_device after a call to cpuidle_unregister_device will
fail which shouldn't be the case.
To prevent this, set registered to 0 when the device is unregistered.
Fixes:
|
|
Rafael J. Wysocki | 0c313cb207 |
cpuidle: menu: Fall back to polling if next timer event is near
Commit |
|
Rik van Riel | e132b9b3bc |
cpuidle: menu: use high confidence factors only when considering polling
The menu governor uses five different factors to pick the idle state: - the user configured latency_req - the time until the next timer (next_timer_us) - the typical sleep interval, as measured recently - an estimate of sleep time by dividing next_timer_us by an observed factor - a load corrected version of the above, divided again by load Only the first three items are known with enough confidence that we can use them to consider polling, instead of an actual CPU idle state, because the cost of being wrong about polling can be excessive power use. The latter two are used in the menu governor's main selection loop, and can result in choosing a shallower idle state when the system is expected to be busy again soon. This pushes a busy system in the "performance" direction of the performance<>power tradeoff, when choosing between idle states, but stays more strictly on the "power" state when deciding between polling and C1. Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Rasmus Villemoes | 3b99669b75 |
cpuidle: menu: help gcc generate slightly better code
We know that the avg variable actually ends up holding a 32 bit quantity, since it's an average of such numbers. It is only a u64 because it is temporarily used to hold the sum. Making it an actual u32 allows gcc to generate slightly better code, e.g. when computing the square, it can do a 32x32->64 multiply. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Rasmus Villemoes | 7024b18ca4 |
cpuidle: menu: avoid expensive square root computation
Computing the integer square root is a rather expensive operation, at least compared to doing a 64x64 -> 64 multiply (avg*avg) and, on 64 bit platforms, doing an extra comparison to a constant (variance <= U64_MAX/36). On 64 bit platforms, this does mean that we add a restriction on the range of the variance where we end up using the estimate (since previously the stddev <= ULONG_MAX was a tautology), but on the other hand, we extend the range quite substantially on 32 bit platforms - in both cases, we now allow standard deviations up to 715 seconds, which is for example guaranteed if all observations are less than 1430 seconds. Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Rafael J. Wysocki | ad1ac94767 |
Merge branches 'pm-cpuidle', 'pm-cpufreq', 'pm-domains' and 'pm-sleep'
* pm-cpuidle: cpuidle: coupled: remove unused define cpuidle_coupled_lock cpuidle: fix fallback mechanism for suspend to idle in absence of enter_freeze * pm-cpufreq: cpufreq: cpufreq-dt: avoid uninitialized variable warnings: cpufreq: pxa2xx: fix pxa_cpufreq_change_voltage prototype cpufreq: Use list_is_last() to check last entry of the policy list cpufreq: Fix NULL reference crash while accessing policy->governor_data * pm-domains: PM / Domains: Fix typo in comment PM / Domains: Fix potential deadlock while adding/removing subdomains PM / domains: fix lockdep issue for all subdomains * pm-sleep: PM: APM_EMULATION does not depend on PM |
|
Anders Roxell | 75274b33e7 |
cpuidle: coupled: remove unused define cpuidle_coupled_lock
This was found with the -RT patch enabled, but the fix should apply to non-RT also. Used multi_v7_defconfig+PREEMPT_RT_FULL=y and this caused a compilation warning without this fix: ../drivers/cpuidle/coupled.c:122:21: warning: 'cpuidle_coupled_lock' defined but not used [-Wunused-variable] Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Sudeep Holla | 6f16886b7c |
cpuidle: fix fallback mechanism for suspend to idle in absence of enter_freeze
Commit |
|
Linus Torvalds | 30f05309bd |
More power management and ACPI updates for v4.5-rc1
- Modify the driver core and the USB subsystem to allow USB devices to stay suspended over system suspend/resume cycles if they have been runtime-suspended already beforehand and fix some bugs on top of these changes (Tomeu Vizoso, Rafael Wysocki). - Update ACPICA to upstream revision 20160108, including updates of the ACPICA's copyright notices, a code fixup resulting from a regression fix that was necessary in the upstream code only (the regression fixed by it has never been present in Linux) and a compiler warning fix (Bob Moore, Lv Zheng). - Fix a recent regression in the cpuidle menu governor that broke it on practically all architectures other than x86 and make a couple of optimizations on top of that fix (Rafael Wysocki). - Clean up the selection of cpuidle governors depending on whether or not the kernel is configured for tickless systems (Jean Delvare). - Revert a recent commit that introduced a regression in the ACPI backlight driver, address the problem it attempted to fix in a different way and revert one more cosmetic change depending on the problematic commit (Hans de Goede). - Add two more ACPI backlight quirks (Hans de Goede). - Fix a few minor problems in the core devfreq code, clean it up a bit and update the MAINTAINERS information related to it (Chanwoo Choi, MyungJoo Ham). - Improve an error message in the ACPI fan driver (Andy Lutomirski). - Fix a recent build regression in the cpupower tool (Shreyas Prabhu). / -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iQIcBAABCAAGBQJWoCQ4AAoJEILEb/54YlRxLscQALEFVKSRnNaco72OqqRZs9Bu 1RI6TgHTpZxR+Ef0+QWqE1QMnDwfImGhKDbSRm/t3S2sMYYZbAOL8cu4y6GmkBv4 bOon/f9WEoPlQCFoo/6U4u8H45rNT5W9zX5+Bva8x+4Wu3n2J1QdvirnS5JHeHe1 o6tGLaHuZXSwX8SLnCk8gJYK1VhATxbubJtpcVtvlnAhO11qUAwsscCrkUmB60i7 5hLyrZb06hoa/hZVcIefGFuSd9qPhzDMQE2M20EohQ7UVkNJQdY9QNHMqCk2P42T nMWCNSwGnwfiO1p9ByXqunOFBCmyL7P+KV/DHsz6TFCVjz+jeG53Kqey9SkSJ/2W iaAE80K9MfOMvg8j7rib6fTn5uXBwRfqdeUDF/Hr64QqJoRn3R2LX4HmZe4L8ufb zA1rece67o8FD+7p7GkNbT3rPV/kA62tn/moFk446X5N+b261Kz90t1DVci8kRVf k+1gcvEdqO0GPpEHoirfXrBvQFixqkXakKj4r2aAob/DldQeLX7CkOUuRRJ1ykec bxwI9R0v8MlVe5rDxg+rPB0I9EFxRDmxqxpU5j0MRWxKnMRzLvBtHuk8YNVS/eU1 xwyJOGcwF6yI0PaCFggPqmhebSrWLE7wJxaK+3bC+yiDTvHYPjB+4MfQrmkRAwwM azgb+ZgXDYx5wXeb8EjB =bKJ9 -----END PGP SIGNATURE----- Merge tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more power management and ACPI updates from Rafael Wysocki: "This includes fixes on top of the previous batch of PM+ACPI updates and some new material as well. From the new material perspective the most significant are the driver core changes that should allow USB devices to stay suspended over system suspend/resume cycles if they have been runtime-suspended already beforehand. Apart from that, ACPICA is updated to upstream revision 20160108 (cosmetic mostly, but including one fixup on top of the previous ACPICA update) and there are some devfreq updates the didn't make it before (due to timing). A few recent regressions are fixed, most importantly in the cpuidle menu governor and in the ACPI backlight driver and some x86 platform drivers depending on it. Some more bugs are fixed and cleanups are made on top of that. Specifics: - Modify the driver core and the USB subsystem to allow USB devices to stay suspended over system suspend/resume cycles if they have been runtime-suspended already beforehand and fix some bugs on top of these changes (Tomeu Vizoso, Rafael Wysocki). - Update ACPICA to upstream revision 20160108, including updates of the ACPICA's copyright notices, a code fixup resulting from a regression fix that was necessary in the upstream code only (the regression fixed by it has never been present in Linux) and a compiler warning fix (Bob Moore, Lv Zheng). - Fix a recent regression in the cpuidle menu governor that broke it on practically all architectures other than x86 and make a couple of optimizations on top of that fix (Rafael Wysocki). - Clean up the selection of cpuidle governors depending on whether or not the kernel is configured for tickless systems (Jean Delvare). - Revert a recent commit that introduced a regression in the ACPI backlight driver, address the problem it attempted to fix in a different way and revert one more cosmetic change depending on the problematic commit (Hans de Goede). - Add two more ACPI backlight quirks (Hans de Goede). - Fix a few minor problems in the core devfreq code, clean it up a bit and update the MAINTAINERS information related to it (Chanwoo Choi, MyungJoo Ham). - Improve an error message in the ACPI fan driver (Andy Lutomirski). - Fix a recent build regression in the cpupower tool (Shreyas Prabhu)" * tag 'pm+acpi-4.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits) cpuidle: menu: Avoid pointless checks in menu_select() sched / idle: Drop default_idle_call() fallback from call_cpuidle() cpupower: Fix build error in cpufreq-info cpuidle: Don't enable all governors by default cpuidle: Default to ladder governor on ticking systems time: nohz: Expose tick_nohz_enabled ACPICA: Update version to 20160108 ACPICA: Silence a -Wbad-function-cast warning when acpi_uintptr_t is 'uintptr_t' ACPICA: Additional 2016 copyright changes ACPICA: Reduce regression fix divergence from upstream ACPICA ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Satellite R830 ACPI / video: Revert "thinkpad_acpi: Use acpi_video_handles_brightness_key_presses()" ACPI / video: Document acpi_video_handles_brightness_key_presses() a bit ACPI / video: Fix using an uninitialized mutex / list_head in acpi_video_handles_brightness_key_presses() ACPI / video: Revert "ACPI / video: driver must be registered before checking for keypresses" ACPI / fan: Improve acpi_device_update_power error message ACPI / video: Add disable_backlight_sysfs_if quirk for the Toshiba Portege R700 cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0 MAINTAINERS: Add devfreq-event entry MAINTAINERS: Add missing git repository and directory for devfreq ... |
|
Rafael J. Wysocki | 5bb1729cbd |
cpuidle: menu: Avoid pointless checks in menu_select()
If menu_select() cannot find a suitable state to return, it will return the state index stored in data->last_state_idx. This means that it is pointless to look at the states whose indices are less than or equal to data->last_state_idx in the main loop, so don't do that. Given that those checks are done on every idle state selection, this change can save quite a bit of completely unnecessary overhead. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Ingo Molnar <mingo@kernel.org> Tested-by: Sudeep Holla <sudeep.holla@arm.com> |
|
Rafael J. Wysocki | 51164251f5 |
sched / idle: Drop default_idle_call() fallback from call_cpuidle()
After commit
|
|
Jean Delvare | 10475b34f4 |
cpuidle: Don't enable all governors by default
Since commit
|
|
Jean Delvare | 66a5f6b639 |
cpuidle: Default to ladder governor on ticking systems
The menu governor is currently the default on all systems. However the documentation claims that the ladder governor is preferred on ticking systems. So bump the rating of the ladder governor when NO_HZ is disabled, or when booting with nohz=off. This fixes the first half of kernel BZ #65531. Link: https://bugzilla.kernel.org/show_bug.cgi?id=65531 Signed-off-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Linus Torvalds | f689b742f2 |
powerpc updates for 4.5
- Ground work for the new Power9 MMU from Aneesh Kumar K.V - Optimise FP/VMX/VSX context switching from Anton Blanchard - Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan - Allow wrapper to work on non-english system from Laurent Vivier - Add rN aliases to the pt_regs_offset table from Rashmica Gupta - Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt - Include KVM guest test in all interrupt vectors from Paul Mackerras - Fix DSCR inheritance over fork() from Anton Blanchard - Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng - Print MSR TM bits in oops messages from Michael Neuling - Add TM signal return & invalid stack selftests from Michael Neuling - Limit EPOW reset event warnings from Vipin K Parashar - Remove the Cell QPACE code from Rashmica Gupta - Append linux_banner to exception information in xmon from Rashmica Gupta - Add selftest to check if VSRs are corrupted from Rashmica Gupta - Remove broken GregorianDay() from Daniel Axtens - Import Anton's context_switch2 benchmark into selftests from Michael Ellerman - Add selftest script to test HMI functionality from Daniel Axtens - Remove obsolete OPAL v2 support from Stewart Smith - Make enter_rtas() private from Michael Ellerman - PPR exception cleanups from Michael Ellerman - Add page soft dirty tracking from Laurent Dufour - Add support for Nvlink NPUs from Alistair Popple - Add support for kexec on 476fpe from Alistair Popple - Enable kernel CPU dlpar from sysfs from Nathan Fontenot - Copy only required pieces of the mm_context_t to the paca from Michael Neuling - Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey - Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt - Add HWCAP bits for Power9 from Michael Ellerman - Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V - Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins - scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand - Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand - cxl: Fix possible idr warning when contexts are released from Vaibhav Jain - cxl: use correct operator when writing pcie config space values from Andrew Donnellan - cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain - cxl: fix build for GCC 4.6.x from Brian Norris - cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris - cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan - Freescale updates from Scott: Highlights include moving QE code out of arch/powerpc (to be shared with arm), device tree updates, and minor fixes. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAABAgAGBQJWmIxeAAoJEFHr6jzI4aWAA+cQAIXAw4WfVWJ2V4ZK+1eKfB57 fdXG71PuXG+WYIWy71ly8keLHdzzD1NQ2OUB64bUVRq202nRgVc15ZYKRJ/FE/sP SkxaQ2AG/2kI2EflWshOi0Lu9qaZ+LMHJnszIqE/9lnGSB2kUI/cwsSXgziiMKXR XNci9v14SdDd40YV/6BSZXoxApwyq9cUbZ7rnzFLmz4hrFuKmB/L3LABDF8QcpH7 sGt/YaHGOtqP0UX7h5KQTFLGe1OPvK6NWixSXeZKQ71ED6cho1iKUEOtBA9EZeIN QM5JdHFWgX8MMRA0OHAgidkSiqO38BXjmjkVYWoIbYz7Zax3ThmrDHB4IpFwWnk3 l7WBykEXY7KEqpZzbh0GFGehZWzVZvLnNgDdvpmpk/GkPzeYKomBj7ZZfm3H1yGD BTHPwuWCTX+/K75yEVNO8aJO12wBg7DRl4IEwBgqhwU8ga4FvUOCJkm+SCxA1Dnn qlpS7qPwTXNIEfKMJcxp5X0KiwDY1EoOotd4glTN0jbeY5GEYcxe+7RQ302GrYxP zcc8EGLn8h6BtQvV3ypNHF5l6QeTW/0ZlO9c236tIuUQ5gQU39SQci7jQKsYjSzv BB1XdLHkbtIvYDkmbnr1elbeJCDbrWL9rAXRUTRyfuCzaFWTfZmfVNe8c8qwDMLk TUxMR/38aI7bLcIQjwj9 =R5bX -----END PGP SIGNATURE----- Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc updates from Michael Ellerman: "Core: - Ground work for the new Power9 MMU from Aneesh Kumar K.V - Optimise FP/VMX/VSX context switching from Anton Blanchard Misc: - Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan - Allow wrapper to work on non-english system from Laurent Vivier - Add rN aliases to the pt_regs_offset table from Rashmica Gupta - Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt - Include KVM guest test in all interrupt vectors from Paul Mackerras - Fix DSCR inheritance over fork() from Anton Blanchard - Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng - Print MSR TM bits in oops messages from Michael Neuling - Add TM signal return & invalid stack selftests from Michael Neuling - Limit EPOW reset event warnings from Vipin K Parashar - Remove the Cell QPACE code from Rashmica Gupta - Append linux_banner to exception information in xmon from Rashmica Gupta - Add selftest to check if VSRs are corrupted from Rashmica Gupta - Remove broken GregorianDay() from Daniel Axtens - Import Anton's context_switch2 benchmark into selftests from Michael Ellerman - Add selftest script to test HMI functionality from Daniel Axtens - Remove obsolete OPAL v2 support from Stewart Smith - Make enter_rtas() private from Michael Ellerman - PPR exception cleanups from Michael Ellerman - Add page soft dirty tracking from Laurent Dufour - Add support for Nvlink NPUs from Alistair Popple - Add support for kexec on 476fpe from Alistair Popple - Enable kernel CPU dlpar from sysfs from Nathan Fontenot - Copy only required pieces of the mm_context_t to the paca from Michael Neuling - Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey - Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt - Add HWCAP bits for Power9 from Michael Ellerman - Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V - Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins - scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand - Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand cxl: - cxl: Fix possible idr warning when contexts are released from Vaibhav Jain - cxl: use correct operator when writing pcie config space values from Andrew Donnellan - cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain - cxl: fix build for GCC 4.6.x from Brian Norris - cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris - cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan Freescale: - Freescale updates from Scott: Highlights include moving QE code out of arch/powerpc (to be shared with arm), device tree updates, and minor fixes" * tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits) powerpc/module: Handle R_PPC64_ENTRY relocations scripts/recordmcount.pl: support data in text section on powerpc powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff powerpc/mm: Fix _PAGE_PTE breaking swapoff cxl: Enable PCI device ID for future IBM CXL adapter cxl: use -Werror only with CONFIG_PPC_WERROR cxl: fix build for GCC 4.6.x powerpc: Add HWCAP bits for Power9 powerpc/powernv: Reserve PE#0 on NPU powerpc/powernv: Change NPU PE# assignment powerpc/powernv: Fix update of NVLink DMA mask powerpc/powernv: Remove misleading comment in pci.c powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing powerpc: Fix build break due to paca mm_context_t changes cxl: Fix DSI misses when the context owning task exits MAINTAINERS: Update Scott Wood's e-mail address powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery() powerpc: Fix style of self-test config prompts powerpc/powernv: Only delay opal_rtc_read() retry when necessary ... |
|
Rafael J. Wysocki | 9c4b2867ed |
cpuidle: menu: Fix menu_select() for CPUIDLE_DRIVER_STATE_START == 0
Commit |
|
Stewart Smith | e4d54f71d2 |
powerpc/powernv: remove FW_FEATURE_OPALv3 and just use FW_FEATURE_OPAL
Long ago, only in the lab, there was OPALv1 and OPALv2. Now there is just OPALv3, with nobody ever expecting anything on pre-OPALv3 to be cared about or supported by mainline kernels. So, let's remove FW_FEATURE_OPALv3 and instead use FW_FEATURE_OPAL exclusively. Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> |
|
Paul Gortmaker | 84599238ea |
drivers/cpuidle: make cpuidle-exynos.c explicitly non-modular
The Kconfig currently controlling compilation of this code is: cpuidle/Kconfig.arm:config ARM_EXYNOS_CPUIDLE cpuidle/Kconfig.arm: bool "Cpu Idle Driver for the Exynos processors" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Paul Gortmaker | fdc7d515ad |
drivers/cpuidle: make cpuidle-ux500.c explicitly non-modular
The Kconfig currently controlling compilation of this code is: cpuidle/Kconfig.arm:config ARM_U8500_CPUIDLE cpuidle/Kconfig.arm: bool "Cpu Idle Driver for the ST-E u8500 processors" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Paul Gortmaker | 94e8057b84 |
drivers/cpuidle: make cpuidle-clps711x.c explicitly non-modular
The Kconfig currently controlling compilation of this code is: drivers/cpuidle/Kconfig.arm:config ARM_CLPS711X_CPUIDLE drivers/cpuidle/Kconfig.arm: bool "CPU Idle Driver for CLPS711X processors" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Rik van Riel | efddfd90fb |
cpuidle,menu: smooth out measured_us calculation
The cpuidle state tables contain the maximum exit latency for each cpuidle state. On x86, that is the exit latency for when the entire package goes into that same idle state. However, a lot of the time we only go into the core idle state, not the package idle state. This means we see a much smaller exit latency. We have no way to detect whether we went into the core or package idle state while idle, and that is ok. However, the current menu_update logic does have the potential to trip up the repeating pattern detection in get_typical_interval. If the system is experiencing an exit latency near the idle state's exit latency, some of the samples will have exit_us subtracted, while others will not. This turns a repeating pattern into mush, potentially breaking get_typical_interval. Furthermore, for smaller sleep intervals, we know the chance that all the cores in the package went to the same idle state are fairly small. Dividing the measured_us by two, instead of subtracting the full exit latency when hitting a small measured_us, will reduce the error. Signed-off-by: Rik van Riel <riel@redhat.com> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Rik van Riel | a9ceb78bc7 |
cpuidle,menu: use interactivity_req to disable polling
The menu governor carefully figures out how much time we typically sleep for an estimated sleep interval, or whether there is a repeating pattern going on, and corrects that estimate for the CPU load. Then it proceeds to ignore that information when determining whether or not to consider polling. This is not a big deal on most x86 CPUs, which have very low C1 latencies, and the patch should not have any effect on those CPUs. However, certain CPUs (eg. Atom) have much higher C1 latencies, and it would be good to not waste performance and power on those CPUs if we are expecting a very low wakeup latency. Disable polling based on the estimated interactivity requirement, not on the time to the next timer interrupt. Signed-off-by: Rik van Riel <riel@redhat.com> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Rik van Riel | 7884084f3b |
cpuidle,x86: increase forced cut-off for polling to 20us
The cpuidle menu governor has a forced cut-off for polling at 5us, in order to deal with firmware that gives the OS bad information on cpuidle states, leading to the system spending way too much time in polling. However, at least one x86 CPU family (Atom) has chips that have a 20us break-even point for C1. Forcing the polling cut-off to less than that wastes performance and power. Increase the polling cut-off to 20us. Systems with a lower C1 latency will be found in the states table by the menu governor, which will pick those states as appropriate. Signed-off-by: Rik van Riel <riel@redhat.com> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Russell King | ab319939a5 |
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
As the driver doesn't support unbinding, nor does it support arbitary binding of devices, disable the bind/unbind attributes for this driver. Also, as the driver has no remove function, it can never be modular, so use builtin_platform_driver() to avoid the module exit boilerplate. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> |
|
Russell King | da1a64f80d |
cpuidle: mvebu: clean up multiple platform drivers
There's no need to use multiple platform drivers, especially when we want to do something different in the probe, but we still use a common probe function. We can use the platform ID system to only register one platform driver, but have it match several devices, and give us the CPU idle driver via the ID's driver_data. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> |
|
Linus Torvalds | fa9a67ef9d |
Additional power management and ACPI material for v4.3-rc1
- Build fix for the new Mediatek MT8173 cpufreq driver (Guenter Roeck). - Generic power domains framework fixes (power on error code path, subdomain removal) and cleanup of a deprecated API user (Geert Uytterhoeven, Jon Hunter, Ulf Hansson). - cpufreq-dt driver fixes including two fixes for bugs related to the new Operating Performance Points Device Tree bindings introduced recently (Viresh Kumar). - Suspend frequency support for the cpufreq-dt driver (Bartlomiej Zolnierkiewicz, Viresh Kumar). - cpufreq core cleanups (Viresh Kumar). - intel_pstate driver fixes (Chen Yu, Kristen Carlson Accardi). - Additional sanity check in the cpuidle core (Xunlei Pang). - Fix for a comment related to CPU power management (Lina Iyer). / -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iQIcBAABCAAGBQJV80XwAAoJEILEb/54YlRxIAkP/RrT4mDO9QZkocO+XYDBB739 oi1aaSDmmVVKlFtFiyX4njS7S+U5UC8PYn5o/fFtVnP1kD9yuZkoak65U3t7bsKK +rjun1SzJeooaLXW4ZAJKyPldi/RrsfRJ2JOaEt2vK03ppjx2mouK1VpjNj+qmYd wwFb4q5S5Rcpph0Sx+xxhpZKoOgBmXk7nWIe5bWDxuORdx4yoxp4lus/P223wFJy r0kJnNyY55mnY4Yx5e3L8W1rMC/Sf6mt8pyMvqRpsKdBHaEbhmGsiERSi0eCZJwr AmL666TVgPk6zNM/yc3mFOTRZeAF3soSWF5R6+n2TswWvWFH+ksM14g9ndb7fTv3 FUuOU3jyfSUj2T4xr0qUZLaQUFB3xNrnWBNnm/CzPwjJtH1u1SK8uBSRqdZnEdGq EeqwnwDLFeSAbG6lQVsKVVAPZHolDCnJPsvZebKdnJH09kjgUdm60BLOnif4QDgw ULPZ6NToFZkrQSMAX1Uqm42iv/qWcHIgS5x43jAmblY3TsuByqRrI7gBCy+hbGSN cQfeCxTdVPi/tUPYlJFmWn43dgEsnceSFKvlQRXGrZJM29BFvhVzJQjTFC8Oj79q OP/Rv28+VeV5J531BQu+w8cvg73GJ3DDab+i91ZkIsd7ZNjRYQKXBfR9TImTSD4l BPjvaPXwDg6EPhwjcpK/ =C7+4 -----END PGP SIGNATURE----- Merge tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull more power management and ACPI updates from Rafael Wysocki: "These are mostly fixes and cleanups on top of the previous PM+ACPI pull request (cpufreq core and drivers, cpuidle, generic power domains framework). Some of them didn't make to that pull request and some fix issues introduced by it. The only really new thing is the support for suspend frequency in the cpufreq-dt driver, but it is needed to fix an issue with Exynos platforms. Specifics: - build fix for the new Mediatek MT8173 cpufreq driver (Guenter Roeck). - generic power domains framework fixes (power on error code path, subdomain removal) and cleanup of a deprecated API user (Geert Uytterhoeven, Jon Hunter, Ulf Hansson). - cpufreq-dt driver fixes including two fixes for bugs related to the new Operating Performance Points Device Tree bindings introduced recently (Viresh Kumar). - suspend frequency support for the cpufreq-dt driver (Bartlomiej Zolnierkiewicz, Viresh Kumar). - cpufreq core cleanups (Viresh Kumar). - intel_pstate driver fixes (Chen Yu, Kristen Carlson Accardi). - additional sanity check in the cpuidle core (Xunlei Pang). - fix for a comment related to CPU power management (Lina Iyer)" * tag 'pm+acpi-4.3-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: intel_pstate: fix PCT_TO_HWP macro intel_pstate: Fix user input of min/max to legal policy region PM / OPP: Return suspend_opp only if it is enabled cpufreq-dt: add suspend frequency support cpufreq: allow cpufreq_generic_suspend() to work without suspend frequency PM / OPP: add dev_pm_opp_get_suspend_opp() helper staging: board: Migrate away from __pm_genpd_name_add_device() cpufreq: Use __func__ to print function's name cpufreq: staticize cpufreq_cpu_get_raw() PM / Domains: Ensure subdomain is not in use before removing cpufreq: Add ARM_MT8173_CPUFREQ dependency on THERMAL cpuidle/coupled: Add sanity check for safe_state_index PM / Domains: Try power off masters in error path of __pm_genpd_poweron() cpufreq: dt: Tolerance applies on both sides of target voltage cpufreq: dt: Print error on failing to mark OPPs as shared cpufreq: dt: Check OPP count before marking them shared kernel/cpu_pm: fix cpu_cluster_pm_exit comment |
|
Rafael J. Wysocki | 4614e0cc66 |
Merge branches 'pm-cpu', 'pm-cpuidle' and 'pm-domains'
* pm-cpu: kernel/cpu_pm: fix cpu_cluster_pm_exit comment * pm-cpuidle: cpuidle/coupled: Add sanity check for safe_state_index * pm-domains: staging: board: Migrate away from __pm_genpd_name_add_device() PM / Domains: Ensure subdomain is not in use before removing PM / Domains: Try power off masters in error path of __pm_genpd_poweron() |
|
Linus Torvalds | c706c7eb0d |
Merge branch 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull ARM development updates from Russell King: "Included in this update: - moving PSCI code from ARM64/ARM to drivers/ - removal of some architecture internals from global kernel view - addition of software based "privileged no access" support using the old domains register to turn off the ability for kernel loads/stores to access userspace. Only the proper accessors will be usable. - addition of early fixup support for early console - re-addition (and reimplementation) of OMAP special interconnect barrier - removal of finish_arch_switch() - only expose cpuX/online in sysfs if hotpluggable - a number of code cleanups" * 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (41 commits) ARM: software-based priviledged-no-access support ARM: entry: provide uaccess assembly macro hooks ARM: entry: get rid of multiple macro definitions ARM: 8421/1: smp: Collapse arch_cpu_idle_dead() into cpu_die() ARM: uaccess: provide uaccess_save_and_enable() and uaccess_restore() ARM: mm: improve do_ldrd_abort macro ARM: entry: ensure that IRQs are enabled when calling syscall_trace_exit() ARM: entry: efficiency cleanups ARM: entry: get rid of asm_trace_hardirqs_on_cond ARM: uaccess: simplify user access assembly ARM: domains: remove DOMAIN_TABLE ARM: domains: keep vectors in separate domain ARM: domains: get rid of manager mode for user domain ARM: domains: move initial domain setting value to asm/domains.h ARM: domains: provide domain_mask() ARM: domains: switch to keeping domain value in register ARM: 8419/1: dma-mapping: harmonize definition of DMA_ERROR_CODE ARM: 8417/1: refactor bitops functions with BIT_MASK() and BIT_WORD() ARM: 8416/1: Feroceon: use of_iomap() to map register base ARM: 8415/1: early fixmap support for earlycon ... |
|
Xunlei Pang | abceaa9cde |
cpuidle/coupled: Add sanity check for safe_state_index
Since we are using cpuidle_driver::safe_state_index directly as the target state index, it is better to add the sanity check at the point of registering the driver. Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |
|
Linus Torvalds | ae98207309 |
Power management and ACPI material for v4.3-rc1
- ACPICA update to upstream revision 20150818 including method tracing extensions to allow more in-depth AML debugging in the kernel and a number of assorted fixes and cleanups (Bob Moore, Lv Zheng, Markus Elfring). - ACPI sysfs code updates and a documentation update related to AML method tracing (Lv Zheng). - ACPI EC driver fix related to serialized evaluations of _Qxx methods and ACPI tools updates allowing the EC userspace tool to be built from the kernel source (Lv Zheng). - ACPI processor driver updates preparing it for future introduction of CPPC support and ACPI PCC mailbox driver updates (Ashwin Chaugule). - ACPI interrupts enumeration fix for a regression related to the handling of IRQ attribute conflicts between MADT and the ACPI namespace (Jiang Liu). - Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar). - ACPI device registration code reorganization to separate the sysfs-related code and bus type operations from the rest (Rafael J Wysocki). - Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause, Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss). - ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan Xinhui, Rafael J Wysocki). - cpufreq core cleanups on top of the previous changes allowing it to preseve its sysfs directories over system suspend/resume (Viresh Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior). - cpufreq fixes and cleanups related to governors (Viresh Kumar). - cpufreq updates (core and the cpufreq-dt driver) related to the turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz). - New DT bindings for Operating Performance Points (OPP), support for them in the OPP framework and in the cpufreq-dt driver plus related OPP framework fixes and cleanups (Viresh Kumar). - cpufreq powernv driver updates (Shilpasri G Bhat). - New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen). - Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean). - intel_pstate driver updates including Skylake-S support, support for enabling HW P-states per CPU and an additional vendor bypass list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao). - cpuidle core fixes related to the handling of coupled idle states (Xunlei Pang). - intel_idle driver updates including Skylake Client support and support for freeze-mode-specific idle states (Len Brown). - Driver core updates related to power management (Andy Shevchenko, Rafael J Wysocki). - Generic power domains framework fixes and cleanups (Jon Hunter, Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson). - Device PM QoS framework update to allow the latency tolerance setting to be exposed to user space via sysfs (Mika Westerberg). - devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas). - System sleep support updates (Alan Stern, Len Brown, SungEun Kim). - rockchip-io AVS support updates (Heiko Stuebner). - PM core clocks support fixup (Colin Ian King). - Power capping RAPL driver update including support for Skylake H/S and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi). - Generic device properties framework fixes related to the handling of static (driver-provided) property sets (Andy Shevchenko). - turbostat and cpupower updates (Len Brown, Shilpasri G Bhat, Shreyas B Prabhu). / -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.22 (GNU/Linux) iQIcBAABCAAGBQJV5hhGAAoJEILEb/54YlRxs+EQAK51iFk48+IbpHYaZZ50Yo4m ZZc2zBcbwRcBlU9vKERrhG+jieSl8J/JJNxT8vBjKqyvNw038mCjewQh02ol0HuC R7nlDiVJkmZ50sLO4xwE/1UBZr/XqbddwCUnYzvFMkMTA0ePzFtf8BrJ1FXpT8S/ fkwSXQty6hvJDwxkfrbMSaA730wMju9lahx8D6MlmUAedWYZOJDMQKB4WKa/St5X 9uckBPHUBB2KiKlXxdbFPwKLNxHvLROq5SpDLc6cM/7XZB+QfNFy85CUjCUtYo1O 1W8k0qnztvZ6UEv27qz5dejGyAGOarMWGGNsmL9evoeGeHRpQL+dom7HcTnbAfUZ walyhYSm/zKkdy7Vl3xWUUQkMG48+PviMI6K0YhHXb3Rm5wlR/yBNZTwNIty9SX/ fKCHEa8QynWwLxgm53c3xRkiitJxMsHNK03moLD9zQMjshTyTNvpNbZoahyKQzk6 H+9M1DBRHhkkREDWSwGutukxfEMtWe2vcZcyERrFiY7l5k1j58DwDBMPqjPhRv6q P/1NlCzr0XYf83Y86J18LbDuPGDhTjjIEn6CqbtI2mmWqTg3+rF7zvS2ux+FzMnA gisv8l6GT9JiWhxKFqqL/rrVpwtyHebWLYE/RpNUW6fEzLziRNj1qyYO9dqI/GGi I3rfxlXoc/5xJWCgNB8f =fTgI -----END PGP SIGNATURE----- Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management and ACPI updates from Rafael Wysocki: "From the number of commits perspective, the biggest items are ACPICA and cpufreq changes with the latter taking the lead (over 50 commits). On the cpufreq front, there are many cleanups and minor fixes in the core and governors, driver updates etc. We also have a new cpufreq driver for Mediatek MT8173 chips. ACPICA mostly updates its debug infrastructure and adds a number of fixes and cleanups for a good measure. The Operating Performance Points (OPP) framework is updated with new DT bindings and support for them among other things. We have a few updates of the generic power domains framework and a reorganization of the ACPI device enumeration code and bus type operations. And a lot of fixes and cleanups all over. Included is one branch from the MFD tree as it contains some PM-related driver core and ACPI PM changes a few other commits are based on. Specifics: - ACPICA update to upstream revision 20150818 including method tracing extensions to allow more in-depth AML debugging in the kernel and a number of assorted fixes and cleanups (Bob Moore, Lv Zheng, Markus Elfring). - ACPI sysfs code updates and a documentation update related to AML method tracing (Lv Zheng). - ACPI EC driver fix related to serialized evaluations of _Qxx methods and ACPI tools updates allowing the EC userspace tool to be built from the kernel source (Lv Zheng). - ACPI processor driver updates preparing it for future introduction of CPPC support and ACPI PCC mailbox driver updates (Ashwin Chaugule). - ACPI interrupts enumeration fix for a regression related to the handling of IRQ attribute conflicts between MADT and the ACPI namespace (Jiang Liu). - Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar). - ACPI device registration code reorganization to separate the sysfs-related code and bus type operations from the rest (Rafael J Wysocki). - Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause, Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss). - ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan Xinhui, Rafael J Wysocki). - cpufreq core cleanups on top of the previous changes allowing it to preseve its sysfs directories over system suspend/resume (Viresh Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior). - cpufreq fixes and cleanups related to governors (Viresh Kumar). - cpufreq updates (core and the cpufreq-dt driver) related to the turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz). - New DT bindings for Operating Performance Points (OPP), support for them in the OPP framework and in the cpufreq-dt driver plus related OPP framework fixes and cleanups (Viresh Kumar). - cpufreq powernv driver updates (Shilpasri G Bhat). - New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen). - Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean). - intel_pstate driver updates including Skylake-S support, support for enabling HW P-states per CPU and an additional vendor bypass list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao). - cpuidle core fixes related to the handling of coupled idle states (Xunlei Pang). - intel_idle driver updates including Skylake Client support and support for freeze-mode-specific idle states (Len Brown). - Driver core updates related to power management (Andy Shevchenko, Rafael J Wysocki). - Generic power domains framework fixes and cleanups (Jon Hunter, Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson). - Device PM QoS framework update to allow the latency tolerance setting to be exposed to user space via sysfs (Mika Westerberg). - devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas). - System sleep support updates (Alan Stern, Len Brown, SungEun Kim). - rockchip-io AVS support updates (Heiko Stuebner). - PM core clocks support fixup (Colin Ian King). - Power capping RAPL driver update including support for Skylake H/S and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi). - Generic device properties framework fixes related to the handling of static (driver-provided) property sets (Andy Shevchenko). - turbostat and cpupower updates (Len Brown, Shilpasri G Bhat, Shreyas B Prabhu)" * tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits) cpufreq: speedstep-lib: Use monotonic clock cpufreq: powernv: Increase the verbosity of OCC console messages cpufreq: sfi: use kmemdup rather than duplicating its implementation cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor() cpufreq: rename cpufreq_real_policy as cpufreq_user_policy cpufreq: remove redundant 'policy' field from user_policy cpufreq: remove redundant 'governor' field from user_policy cpufreq: update user_policy.* on success cpufreq: use memcpy() to copy policy cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event cpufreq: mediatek: Add MT8173 cpufreq driver dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings PM / Domains: Fix typo in description of genpd_dev_pm_detach() PM / Domains: Remove unusable governor dummies PM / Domains: Make pm_genpd_init() available to modules PM / domains: Align column headers and data in pm_genpd_summary output powercap / RAPL: disable the 2nd power limit properly tools: cpupower: Fix error when running cpupower monitor PM / OPP: Drop unlikely before IS_ERR(_OR_NULL) PM / OPP: Fix static checker warning (broken 64bit big endian systems) ... |
|
Linus Torvalds | a1d8561172 |
Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The biggest change in this cycle is the rewrite of the main SMP load
balancing metric: the CPU load/utilization. The main goal was to make
the metric more precise and more representative - see the changelog of
this commit for the gory details:
|
|
Xunlei Pang | 4c1ed5a607 |
cpuidle/coupled: Remove redundant 'dev' argument of cpuidle_state_is_coupled()
For cpuidle_state_is_coupled(), 'dev' is not used, so remove it. Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> |