wlcore allocates two static structs wl1271_band_2ghz & wl1271_band_5ghz
which are used/modified by Reg-Domain e.g. some channel might be marked
as passive at some point. Make sure we don't keep stale settings around
if the HW is unregistered/registered during operation.
[Arik - use Tx-power constant and tweak commit message]
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make sure free_link is always called when removing an interface. This
ensures all skbs belonging to this interface are returned to mac80211.
Otherwise these dangling skbs might crash the system on the next
call to wl1271_tx_reset_link_queues(). This happens on recovery/stop or
an unsuccessful Tx flush.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Otherwise we risk contention for private members of our global structure
while op_stop_locked is running.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Sometimes the driver can perform a recovery while Tx is
active, this will trigger unnecessary warning which might
delay the recovery for more than 100 mS.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 18xx fw supports greenfield so add the
IEEE80211_HT_CAP_GRN_FLD flag to the supported
ht capabilities flags.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When removing an interface currently performing a ROC operation, clear
the current ROC state. This is useful especially during recovery and
keeps mac80211 in sync to our state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
all the current firmwares support elp, so
we can safely remove WLCORE_QUIRK_NO_ELP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Under some circumstances, that fw might be asked to
remove a rx ba sessions it doesn't know about. In
this case, instead of triggering a recovery, accept
the error code (CMD_STATUS_NO_RX_BA_SESSION) and
ignore it.
[Arik - indicate failure up when the BA session cannot be setup]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently, each fw command/acx that return a status code
different than CMD_STATUS_SUCCESS will trigger a recovery
in the driver.
However, it is a valid for some fw commands to fail (e.g.
due to temporary lack of resources), so add new functions
that allow passing bitmap of valid error return values.
(make the current wl1271_cmd_send/wl1271_cmd_configure
wrappers around the new functions, in order to avoid
changing the whole driver)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
First set (low, medium and high TX power values) is used
for STA-HP background role. The 2nd set is used for other roles.
Update other mac/phy parameters according to new FW.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Conflicts:
drivers/net/wireless/ti/wl18xx/main.c
Update mac/phy paramters according to the default HP SISO boards.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 12xx FW doesn't support non-zero session ids for AP-mode. Introduce
an appropriate quirk to make sure the session id is always zero when
needed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For wl18xx, only the chip ID and the minor version number are
relevant. Ignore the other numbers which are either not used or
relate to internal projects or internal branches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Previously we were only checking the single-role firmware version.
Now add code to check for the firmware versions separately for each
firmware type.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware type and the project number fields in the firmware
version number, cannot be checked as if they increase sequentially,
because the former is the firmware type and the latter is an internal
project number. There's no guarantee that these numbers will remain
incremental, so use WLCORE_FW_VER_IGNORE.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmwares version string contain 5 integers. We used to consider
all the digits (except for the first one, which indicates the chip) as
linearly increasing version numbers. This is not correct, because
some of the integers indicate type of firmware (eg. single-role
vs. multi-role) or the internal project it was created for.
Besides, this varies a bit from chip to chip, so we need to make the
firmware version checks more flexible (eg. allow the lower driver to
ignore some of the integers). Additionally, we need to change the
code so that we only check for a linearly increasing number on the
fields where this actually makes sense.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We don't distinguish between STA and AP firmwares anymore, so the
firmware version checking and quirks setting in wl12xx isn't needed
anymore.
Remove implementation of .identify_fw in wl12xx and deprecated
definitions. Don't remove the op entirely from wlcore, because it may
be needed for more fine-grained checking later.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move wl12xx-specific chip ID macros to the wl12xx driver and rename
them to 127X and 128X for clarity since both the "1" (2.4GHz) and the
"3" (2.4GHz and 5GHz) variants use the same chip ID.
Signed-off-by: Luciano Coelho <coelho@ti.com>
add support for recovery settings including bug_on_recovery and
no_recovery options.
These options can now be set using wl18xx-conf.bin file and wlconf
tool.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It's sometimes useful to gather information about the firmware
stability in long test runs, especially to see if problems are
recurring frequently or not. With this commit we count the number of
times a hardware recovery was issued and print it out during recovery
and in the driver_state in debugfs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Adapt the new mac80211 BSS_CHANGED_PS notification,
and do the ps handling in mac80211's per-vif
callback (.bss_info_changed), rather than in
the per-device (.config) callback.
Make sure to configure it only after association.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
mask out CCK rates from the AP's local rates
when the interace is p2p interface (GO).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Try an opportunistic ROC when a STA is first added and stop the ROC when
the STA is removed or successfully authenticated. This would ensure we
don't miss auth/assoc/EAPOL packets during connection
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
18xx chips are capable of staying on 2 channels at the same time.
Introduce a chip-family specific parameter to set the number of channels
in the interface-combinations published by the driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Due to a bug, the fw asserts on fw log stop when dbg-pins are used.
Don't stop the fw log in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We support changing the channel BW when we started the STA role on
a 40Mhz bandwidth. Otherwise a reconnection is required.
Save the started channel width and use it when channel width updates
arrive.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow configuring different dwell times to the different
scan types (regular and scheduled).
Add new configuration entry (dwell_time_dfs) to
conf_scan_settings, in order to allow setting
different values for normal scan and scheduled scan.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
we have done updating the driver to the new fw
api, so make the driver operational again.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interface might go down before we got the SCHED_STOPPED
event, so make sure to call ieee80211_sched_scan_stopped()
if the scanned interface is removed.
Replace sched_scanning with sched_vif in order to save
the scanned interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In 18xx the calibration process of the PHY Cortex domain
requires to perform an active calibration of the channel
before it can be used for transmission. To fulfill world
wide regulatory restrictions, fw should be always
synchronized/updated with current CRDA configuration.
Add a new "CMD_DFS_CHANNEL_CONFIG" command to update the
fw with current reg-domain, this command passes a bit map
of channels that are allowed to be used for transmission.
The driver shall update the fw during initialization and
after each change in the current reg-domain
configuration. The driver will save the channel number of
incoming beacons during the scan process, as they might
be a result of the passive scan on
"IEEE80211_CHAN_PASSIVE_SCAN" channel and will update the
fw accordingly once the scan is finished, the purpose of
this is to be ready in case of the authentication request
on one of these disabled (uncalibrated) channels.
The new command requires to wait for the fw completion
event "DFS_CHANNELS_CONFIG_COMPLETE_EVENT".
No scan commands (including the sched scan) can be
executed concurrently with the "CMD_DFS_CHANNEL_CONFIG",
wl->mutex ensures that.
[Arik - move reset of reg_ch_conf_last to safe place inside
op_stop_locked]
[Eliad - adjust to new event waiting api]
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
A new session_id is generated on link allocation.
it is saved in a global array and used later, on tx.
The new fw api adds new bcast/global_session_id
fields to start_role(ap) command, and a new session_id
field to add_peer command. align the driver with it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New fields were added to start_role(ap) and
set_peer_state commands, so the fw will be
able to know whether the sta/ap supports
wmm (the fw uses it in order to choose the
AC for some of its internally-generated frames)
For sta, take this value right from bss_conf->qos.
For ap, check for wmm support by looking for the
WMM IE in the configured beacon.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The event mailbox in wl18xx has a different
(non-compatible) structure.
Create common functions in wlcore to handle the
events, and call them from the chip-specific
event mailbox parsers.
This way, each driver (wl12xx/wl18xx) extracts
the event mailbox by itself according to its
own structure, and then calls the common
wlcore functions to handle it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some fields were added to the channel_switch and
stop_channel_switch commands. Unfortunately,
the new 18xx channel_switch struct is not backward
compatible with the 12xx channel switch struct.
Add a new channel_switch op to wlcore, and update
the driver accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some regdomains have more than 23 valid 5ghz channels,
so 18xx's MAX_CHANNELS_5GHZ was increased to 32.
Since now we have different max 5ghz channels values
for wl12xx and wl18xx, add a new wl->max_channels_5ghz
field, and use it for scan channels configuration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The scan APIs of 12xx and 18xx are totally different.
Use some common functions as much as possible (e.g.
for setting scan channels), but split scan.c into
chip-specific scan.c files, each implementing its
own scan mechanism.
(in other words - move most of the current wlcore's
scan.c into wl12xx, and implement a similar mechanism
in 18xx, according to the new api)
New wlcore ops are introduced in order to call the
chip-specific scan functions.
The template indices used for each scan (regular/scheduled)
are also different between the chips, so set the correct
indices used for each scan type after identifying the chip.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new fw (8.5.0.0.28) is not backward compatible
with older drivers.
Use a new fw name (along with bumping the min
fw version), and add some code to fail
any boot attempt during the fw api alignment
patches (as the driver is not functional in
these transitional patches).
This code will be removed after the api alignment
will be done.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
18xx and 12xx have different scan APIs. In 18xx,
the scan and the sched scan use the same struct.
Prepare the scan configuration functions to it, by taking
more generic params (e.g. ieee80211_channel) instead of
specific structs/requests.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When we stop sched scan during connection, we shouldn't
call ieee80211_sched_scan_stopped directly, but do it
in the normal flow, as part of the SCHED_SCAN_COMPLETED
event handling.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove goto and label in the code where a simple if can be used. If
nothing else, this is at least confusing git diff, which shows the
label name as the name of the function.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In multi-vif setup it's useful to know the role_id
being configured.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
With the new connection flow, start_sta is called before
the remote rates where updated. Use our own supported rates
instead to make sure we don't disable any potential rate
(the rate policies will be updated later, but there is
currently no way to update the remote rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pass a variable indicating whether HT is enabled,
instead of duplicating the function call with
different arguments.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When first configuring the rate policy, before auth,
we still don't have the correct rates that were
agreed during association.
Reconfigure the rate policy on association in order
to update them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The supported_rates field should contain all our supported
rates, even if the remote peer doesn't support them.
(rename CONF_TX_AP_ENABLED_RATES to CONF_TX_ENABLED_RATES,
as we now use it for both ap and sta)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The default ps mode of the fw is auto, while the default
ps mode of mac80211 is active (ps off).
In order to sync them, configure active ps on association.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the sta_state notifications to ROC when a station
is about to connect, and CROC respectively on
authorization (success) / deletion (failure).
Change the wl12xx_update_sta_state() flow to bail out
only on error, so multiple code blocks could refer
to the same state.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add some basic chanctx implementation - debug prints,
and save the vif's channel/band/type.
After that, we no longer need to handle channel change
notifications on op_config.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We care only about the operational channel, not
about the temporal hw channel (which won't have
any real meaning in multi-channel env anyway)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
implement the reamin_on_channel() callback by starting
a dev role (already associated with the current vif)
on the requested channel/band.
This channel is usually different from the channel
of the sta role, so pass it to wl12xx_roc() as well,
and notify mac80211 (async) when the fw is ready
on the new channel.
Now, in case of offchannel tx, we should use the dev
role hlid, instead of the sta hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
for some reason, the wl12xx fw is not able to rx/tx
on the first start_sta cmd.
Workaround it by issuing a dummy start_sta + stop_sta
before starting the sta for the final time.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make the connection flow simpler by starting
sta role on bssid change.
Currently, we start dev role when going idle-off,
and start the sta role only after association
indication. This complicates the connection
flow with some possible intermediate states.
Make it simpler by starting sta role on bssid change,
which now happens *before* auth req get sent.
Update the handling of mac80211's notifications
and change wl1271_join/unjoin accordingly -
* Split wl1271_join() into wlcore_join (tuning on
a channel/bssid) and wlcore_set_assoc (configure
sta after association).
* Rename wl1271_unjoin() to wlcore_unset_assoc(), as
it is no longer the inversion of wl1271_join()
(now it's only used to disconnect associated sta /
joined ibss, without stopping the role).
* Set ssid before starting station role (needed for
start_role(sta)
While on it, split wl1271_bss_info_changed_sta() into
some sub-functions.
since we no longer use dev role in the connection flow,
we now always use the hlid of the sta role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to check whether unsigned variable is less than 0.
CC: Luciano Coelho <coelho@ti.com>
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
In corner case for wl12xx_spi_raw_write() when
len == SPI_AGGR_BUFFER_SIZE
we don't setup correctly spi transfer_list.
Next we will have garbage and strange errors
reported by SPI framework (eg. wrong speed_hz,
failed to transfer one message from queue)
when iterate transfer_list.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Luciano Coelho <coelho@ti.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The function wl12xx_set_power_on is only called twice, once in
wl12xx_chip_wakeup and once in wl12xx_get_hw_info. On the failure of the
call in wl12xx_chip_wakeup, the containing function just returns, but on
the failure of the call in wl12xx_get_hw_info, the containing function
calls wl1271_power_off. This does not seem necessary, because if
wl12xx_set_power_on has set the power on and then fails, it has already
turned the power off.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f,free,a;
parameter list[n] ps;
type T;
expression e;
@@
f(ps,T a,...) {
... when any
when != a = e
if(...) { ... free(a); ... return ...; }
... when any
}
@@
identifier r.f,r.free;
expression x,a;
expression list[r.n] xs;
@@
* x = f(xs,a,...);
if (...) { ... free(a); ... return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wlcore_op_set_key() calls wl18xx_set_key(),
which in turn executes some of his function
calls without acquiring wl->mutex and making
sure the fw is awake.
Adding mutex_lock()/ps_elp_wakeup() calls is
not enough, as wl18xx_set_key() calls
wl1271_tx_flush() which can't be called while
the mutex is taken.
Add the required calls to wlcore_op_set_key,
but limit the queues_stop and flushing
to the only encryption types in which
a spare block might be needed (GEM and TKIP).
[Arik - move state != ON check]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The current elp timeout (the same as the dynamic
ps timeout - 1500ms) is too high. Usually,
wl1271_ps_elp_sleep() get called right after tx/rx,
which is fine, but some command might get sent
even when there is no traffic (e.g. ht changes
triggered by beacon frames), and leaving the
device awake for 1500ms in this case is redundant.
Use a timeout of 30ms.
The fw won't enter elp anyway before the dynamic-ps
timeout was expired as well (and it entered ps
successfully).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The NVS file is loaded by the device's probe callback with the help of
request_firmware(). Since request_firmware() relies on udevd, the
modules cannot be loaded before hotplug events are handled.
Fix this by loading the NVS file asynchronously and continue
initialization only after the firmware request is over.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Move most of the device-specific probe functionality into setup(), a new
op. By doing this, wlcore_probe will be the first to request a firmware
from userspace, making it easier to load the NVS file asynchronously.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When the no_recovery flag is used, the recovery work will not restart
the FW and the state will not be set to 'on'. To enable post-mortem
analysis, allow memory access in the 'restarting' state.
Also, since the FW might not be operational, don't fail the read/write
operations if elp_wakeup fails.
Reported-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Currently, all the (station) roles use the same
keep-alive template id (0). However, the klv
template ids shouldn't be shared by different
roles.
Implement a simple klv_templates bitmap, and let
each role allocate its own klv template id on
role initialization.
[Arik - remove invalidation of KLV template when getting into "idle".
This is already handled in unjoin]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Previously, invalidation of the keep-alive template was
done when going idle. However, while removing the
idle-handling we didn't move the keep-alive template
invalidation to another place.
This finally resulted in fw error when trying to use
the keep-alive template by another role.
(Note that we still have an error here - each role
should have its unique keep-alive template id, while
currently they all use CMD_TEMPL_KLV_IDX_NULL_DATA (0).
This only works now because we don't support concurrent
connected stations yet)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The driver used siso20 in this case for legacy reasons.
Reported-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The interrupt line is enabled by wl12xx_enable_interrupts and
wl18xx_enable_interrupts, but it will not be disabled in all failure
paths. Fix this.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
While recursive recovery is avoided during shutdown, a new recovery may
be queued when the FW boots. The recovery work will then try to stop an
already stopped hardware, which will most likely result in a kernel
panic.
Fix this by verifying that wl->state is on before queueing a new
recovery.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
add phy_fw_version_str to debugfs driver_state file.
information is taken during boot and stored in wl->chip.phy_fw_ver_str.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Limit SPI transmissions to the wl12xx max buffer size, as only 12xx was
tested with SPI.
This allows us to remove the global aggregation buffer constant.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Use number_of_assembled_ant5 phy param to indicate if A band is enabled:
if number_of_assembled_ant5 != 0 then it is enabled otherwise it is
disabled.
This aligns with phy implementation that uses this param both to indicate
if band is active and the number of antennas.
This parameter replaces enable_11a module param that was removed.
User-Space applications can use wlconf and/or INI files to disable A band
using this parameter.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This allows us to have a p2p-management interface (in STA mode),
as we as a group dedicated interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Enable device roles just before starting it.
This way, a single device role should be enough
for all vifs, as we can't use concurrent device
roles (which require ROC) anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
enabled (but not-started) sta role should be good enough
for scanning (both normal and scheduled), so use it
instead of the device_role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Make debug prints operational when dynamic debug is not defined.
This allows better debugging in production environments.
Change the driver prefix to "wlcore" while were at it.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Allow 3 native mac addresses on 18xx. On 12xx allow 2 native mac
addresses and set the LAA bit to create a third mac address. This
enabled operation with a separate group interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
mac80211's resume() callback might get called even if
the sta is not associated (but only up). The
resume sequence in this case results in configuring
the wake-up conditions of a non-started role, which
causes fw assertion.
Fix it by bailing out if the STA is not connected
(like we do on suspend()).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
wowlan filters should be configured in any case in suspend/resume.
This shouldn't be dependent on whether wakeup conditions are the
same for suspend and resume states. Only the FW command to
reconfigure wakeup conditions should be avoided in such a case.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Aggregation buffer size is set separately per 18xx/12xx chip family.
For 18xx aggragation buffer is set to 13 pages to utilize all
the available tx/rx descriptors for aggregation.
[Arik - remove redundant parts from the patch]
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Force Tx during the flush if there are packets pending in the driver.
This actually solves a bug where we would get called from the mac80211
wq context, which would prevent tx_work from getting queued, even when
the mutex is unlocked.
Don't stop the queues needlessly if there's nothing to flush. Use a
larger delay when sleeping to give the driver a chance to flush and
avoid cpu busy looping. Re-arrange the loop so the last iteration is
not wasted.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Print how much time a flush took. This will help debug the time it takes
to switch between channels.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The IEEE80211_TX_CTL_NO_CCK_RATE flag is only set for mgmt packets
transmitted during p2p connection setup. Make sure to use the lowest
OFDM rate guarantee the peer always hears us.
Change the p2p rate policy to contain only the 6mpbs rate to acheive
this effect.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This solves interoperability issues with peer that don't seem to "hear"
management packets transmitted in higher rates. Based on a previous
patch by Igal Chernobelsky.
Cc: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
recovery_work should be cancelled when stopping the device,
not when removing an interface (this is probably a leftover
from the single-role days)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When a function requests to recover, it would normally abort and will
not send any additional commands to the HW. However, other threads may
not be aware of the failure and could try to communicate with the HW
after a recovery was queued, but before the recovery work began.
Fix this by introducing an intermediate state which is set when recovery
is queued, and modify all state checks accordingly.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When a single fw is being used for both single-role
and multi-role cases (e.g. 18xx), wl->mr_fw_name is
NULL, which results in NULL dereference while trying
to load the multi-role fw.
In this case, always use the single-role fw, and avoid
redundant fw switch by checking for this case in
wl12xx_need_fw_change() as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
default switch configuration set to pg2 chips (rdl 1/2/3/4).
removed hacks for specific board types.
pg1.x boards are now supported only using module params
or specific conf files.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Declare any firmware that might be used by this driver.
If all drivers declare their firmware usage, then a sufficiently
complete list of firmware files can then be used to pare down
the external linux-firmware package to just the files in actual use.
Cc: Luciano Coelho <coelho@ti.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Use a module_platform_driver declaration instead of replicating the
init and exit functions in the driver.
Based on the patch for wl18xx by Devendra Naga.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
the driver's init and exit routines can be implemented with the
module_platform_driver, as the init and exit code is same as
that of the module_platform_driver
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
avoid using the skb CB for getting the appropriate sta.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a bug hiding here since the hlid was sometimes inferred from
the sta, which might be invalid at this point.
Instead, propagate the hlid from the skb-queue where we got the skb
in the first place.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some rare cases, the CMD_ROC completion may take over 1 second.
The timeout had earlier been increased to 1000ms (from 750ms), but it
is still not enoug. Increase it to 1500ms.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We need to wait for the command completion event when we send the
CMD_ROLE_STOP event otherwise we may try to send CMD_ROLE_START too
soon and get out-of-sync with the firmware.
In some cases, the firmware may not send the event, so we wait for the
event or for the timeout, whichever comes first.
This patch is based on an earlier version by Eliad.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use this opportunity to consolidate the check for MIMO support into a
separate function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
handle errors of nla_put() inside the if(nla_put...) {}
This makes the code simpler and clearer because:
we take advantage from the fact that we have only one nla_put
in our routines (so no real need for goto label).
this avoids ugly goto forward followed by goto backward.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
this completes the calibrator based fem detect logic in driver:
driver starts (by calibrator) in plt_mode PLT_FEM_DETECT
wlcore inits and starts plt on wl12xx
wl12xx fetches fem number from firmware and stores it in wl->fem_manuf
wl12xx immediatly returns (doesn't start radio, etc...)
wlcore returns the fem_manuf to calibrator using WL1271_TM_ATTR_DATA
plt_mode is stopped
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
bip calibration is not required in wl18xx. Therefore we
disable also auto fem (using calibrator fem detect) mode.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
add wl->plt_mode that is used to indicate different plt
working modes: this will be used to implement calibrator side
auto fem detection where driver asks firmware to detect
the wlan fem radio type and returns it to calibrator.
this is not implemented yet and plt_modes: PLT_ON and
PLT_FEM_DETECT currently behave the same.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After the latest mac80211 changes, the sta has
the ap's sta pointer even before association.
This cause the auth and assoc frames to be sent
with the standard ap's rates, rather than the
basic rates.
Change the tx rate policy logic to use the regular
ap rates only for data packets (so control and mgmt
packets will be sent with basic rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During interface removal, don't adjust sleep_auth if we are during
recovery. Since the FW is potentially dead we shouldn't talk to it.
Reported-by: Yossi Wortzel <yossiw@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize val to 0, to remove the following warning with
CONFIG_CC_OPTIMIZE_FOR_SIZE. The compiler used was gcc 4.4.1
(Sourcery G++ Lite 2010q1-202).
drivers/net/wireless/ti/wl18xx/io.c: In function 'wl18xx_top_reg_read':
drivers/net/wireless/ti/wl18xx/io.c:57: warning: 'val' may be used uninitialized in this function
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Send EAPOLs using minimum basic rate for AP, STA, p2p GO and Client.
The patch fixes p2p connection issue with Realtek device in p2p
certification test 5.1.13 (DEVUT reinvokes Persistent Group).
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ht_mode added to wl18xx conf struct in order to support different modes
from the configuration file, as well as module params, and by default
(working without a conf file and/or no module params).
the hack regarding conf.phy.low_band_component_type for each board
is now explicitly handled after parsing module params.
missing default values to wl18xx config added.
fix string module params not to have defaults (so if empty, param
can be taken from conf file).
update conf version to 3.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
suspend and resume callbacks configure wakeup conditions to the FW
which may be different between suspend and resume.
This feature is currently not utilized as both in suspend and resume
FW wakeup every 1 DTIM. Avoid waking up the chip and doing the FW command
unless there's an actual difference in the wakeup conditions.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We get DMA alignment trouble if the beginning of the conf.phy struct is
not aligned to 4 bytes. Use kmemdup to ensure alignment.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We should free "chunk" here before returning the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't use the ht_mode module parameter for determining AP supported
rates. We can rely on channel type, since HT40 won't be enabled if our
HT cap doesn't support it.
Enable MIMO only if there enough antennas, and rely on per-peer rate
limitation to prevent IOPs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
commit 587cc28 ("wlcore: compare ssid_len before comparing
ssids") introduced a new bug - the ssid length from the
request struct was compared against the ssid length of
another request, instead the one of the cmd.
This might cause the sched scan request to fail
(with -EINVAL) in many cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
It seems some parties have bad user experience when smaller values
are used. This should have little implications for power consumption,
since traffic is bursty in nature.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Avoid using the IEEE80211_NUM_BANDS constant for arrays sizes etc, as
this can contain bands unsupported by the driver (e.g. 60Ghz). Use an
internal constant to determine the number of bands.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
If some IO read/write fails while the FW is not loaded, a recovery
will not take place. This means the SDIO_FAILED flag will stay in place
forever and prevent further read/writes.
This can happen if a check for STATE_OFF was forgotten in some routine.
Take this opportunity to rename the flag to IO_FAILED, since we support
other buses as well.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
wlcore needs to wait for certain events for example
for roc complete event. Usually the events are received
from the FW very fast, therefore wlcore can poll with
a short delay and if after a second the event was
not received yet poll with a long (1-5 msec) delay.
This implementation is similar to the sending of
commands to the FW.
Empirically the change reduced the wait for roc event
from ~10-40msec to 100s of usecs.
[replace udelay/msleep with usleep_range - Arik]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The interrupt line is disabled in op_stop using disable_irq. Since
pending interrupts are synchronized, the mutex has to be released before
disabling the interrupt to avoid a deadlock with the interrupt handler.
In addition, the internal state of the driver is only set to 'off'
after the interrupt is disabled. Otherwise, if an interrupt fires after
the state is set but before the interrupt line is disabled, the
interrupt handler will not be able to acknowledge the interrupt
resulting in an interrupt storm.
The driver's operations might be called during recovery. If these
acquire the mutex after it was released by op_stop, but before the
driver's state is changed, they may queue new work items instead of just
failing. This is especially problematic in the case of scans, in which a
new scan may be scheduled after all scan requests were cancelled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We have some API changes and new features in the new firmwares that
are not compatible with older drivers. Increase the version of the FW
filenames for wl12xx to 5.
Additionally, remove the duplicate definitions from wlcore_i.h and
remove the MODULE_FIRMWARE macro calls from the SDIO and SPI modules,
since they're irrelevant there.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver configures the firmware template for probe requests during
the scan process. If the same template is used for one-shot and sched
scans they will override each other when running scans simultaneously.
This fix works only on firmwares later than X.3.9.2.112 for single
role and X.3.9.2.23 for multi-role.
[Some cleaning-up and renaming of the quirk to something smaller --
Luca.]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If recovery is called when the FW is off, we should clear the recovery
flag. Otherwise we risk booting the driver in permanent pending-recovery
state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't read the FW panic log or print other debug data when recovery is
intended (i.e. FW type switch). This takes valuable time and can be
confusing to the user.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This command is buggy (doesn't take the mutex) and unused. Instead, the
"start_recovery" file is used for the same purpose. Remove the code but
keep the command constant to avoid breaking the testmode ABI.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a Tx queue is currently stopped because of our Tx watermark flow
control, don't stop it again. This causes a warning to appear.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Refuse to boot if the FW version is too old. The minimum version is set
per chip, with the option of setting it per PG in the future.
When boot fails because of an old FW, display a helpful message.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New wl12xx firmware supports scheduled scans also while connected.
Stop blocking sched scan requests when connected and add a quirk to
block in hardware that don't support it (currently wl18xx doesn't).
This requires FW version 6/7.3.10.2.112 for single-role and
6/7.5.6.0.25 for multi-role.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.
Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As recovery queuing can now occur from multiple code paths
it's convenient to know what triggered it in all cases
other than an intended recovery which is part of the
switch between single role to multi role.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Following the addition of propagating errors from the bus ops
there's a need to distinguish between bus errors (including timeout)
and a legitimate timeout occuring in cmd_wait_for_event_or_timeout.
In case of real bus errors we need to queue recovery even in cases
where a timeout on a response from the FW to a command is acceptable.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Victor Goldenshtein