Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
GCMP MIC length is not filled for GCMP/GCMP-256 cipher suites in
PMF enabled case. Due to mismatch in MIC length, deauth/disassoc frames
are unencrypted.
This patch fills proper MIC length for GCMP/GCMP-256 cipher suites.
Tested HW: QCA9984, QCA9888
Tested FW: 10.4-3.6-00104
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As Hash based reo destination selection is configured,
the decapped packets reach different reo destintion rings
based on the destintaion ring selected for the computed hash (based on
the 5-tuple {ip src/ip dst/src port/dst port/protocol}) by hw and
as configured by driver.
Hence the current implementation of amsdu list based processing after all
the subframes of amsdu are received (since all msdu's for a pdev are
received in same reo dest ring), is not applicable here and hence is
replaced with per msdu based handling as these subframes
can be received in different reo dest rings.
Also, as some of the rx descriptor fields might be valid only for the
first msdu (for ex. received 80211 header, encryption type, etc),
it might not be useful now as we cannot sync between different
subframes received in different rings. Hence do not rely on those
fields and replace them with fieds valid only on per msdu descriptors.
Also cache other details such as encryption type for a peer so that
it can be reused when a packet is received from it.
Co-developed-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current implementation of pdev based reo destination ring
selection is replaced by hash based ring selection so as to
ensure all the available rings are utilized for better performance.
The 4 reo destination rings are selected by the HW based on the
hash value computed from the received packet based on the 5 tuple
{ip src/ip dst/src port/dst port/protocol}. Out of the 32 hash values
used by the hw, the driver assigns 8 values per reo destination ring
to each of the 4 reo destination rings.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before dumping tx_stats proper validation was not been taken care of.
Due to which we were encountering null pointer dereference(kernel panic).
This scenario will arise when a station is getting disconnected and
we are changing the STA state by ath11k_mac_op_sta_state and assigning
tx_stats as NULL and after this the mac80211 will destroy the
debugfs entry from where we are trying to read the stats.
If anyone tries to dump tx_stats for that STA in between setting
tx_stats to NULL and debugfs file removal without checking the NULL
value it will run into a NULL pointer exception.
Proceeding with the analysis of "ARM Kernel Panic".
The APSS crash happened due to OOPS on CPU 3.
Crash Signature : Unable to handle kernel NULL pointer dereference at
virtual address 00000360
During the crash,
PC points to "ath11k_debug_htt_stats_init+0x16ac/0x1acc [ath11k]"
LR points to "ath11k_debug_htt_stats_init+0x1688/0x1acc [ath11k]".
The Backtrace obtained is as follows:
[<ffffffbffcfd8590>] ath11k_debug_htt_stats_init+0x16ac/0x1acc [ath11k]
[<ffffffc000156320>] do_loop_readv_writev+0x60/0xa4
[<ffffffc000156a5c>] do_readv_writev+0xd8/0x19c
[<ffffffc000156b54>] vfs_readv+0x34/0x48
[<ffffffc00017d6f4>] default_file_splice_read+0x1a8/0x2e4
[<ffffffc00017c56c>] do_splice_to+0x78/0x98
[<ffffffc00017c63c>] splice_direct_to_actor+0xb0/0x1a4
[<ffffffc00017c7b4>] do_splice_direct+0x84/0xa8
[<ffffffc000156f40>] do_sendfile+0x160/0x2a4
[<ffffffc000157980>] SyS_sendfile64+0xb4/0xc8
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dumping the SRNG stats during FW assert, this would help
in debugging ring stuck issues.
Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fill the channel information from rx channel for the packet
which has invalid channel info from meta data.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Firmware sends HTT event to host whenever there is a
backpressure on RX rings, Handling such event and dumping
info on the console under the "ATH11K_DBG_DP_HTT" debug level.
Fetching RX ring backpressure histogram from FW via htt_stats debugfs.
#echo "24" > /sys/kernel/debug/ath11k/ipq8074/macX/htt_stats_type
#cat /sys/kernel/debug/ath11k/ipq8074/macX/htt_stats
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds code to handle the BSS_CHANGED_BSS_COLOR flag. It will
trigger the propagation of BSS color settings into the FW. Handling is
slightly different between AP and STA interfaces.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the he_operation field of the beacon sets a BSS color, we need to inform
the FW of the settings. This patch adds the WMI command handlers required
to do so.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver currently does not use wake_txq_queue. This leads to the
tx_queue_len being defaulted to 1000. Setting this parameter will
change the queue_len to 4096 which is more fitting for HE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enabling PN checking in the hardware; hardware checks
the PN of the received packets and reports the errors
to the host for further handling; default action is to
drop such packets. TSC (TKIP sequence counter)
validation is also offloaded.
Hardware validates PN/TSC only for unicast packets;
for group addressed packets, PN validation is done
in mac80211.
PN errors are reported to the driver via WBM RX release
ring and can be dumped by using the following command.
"cat /sys/kernel/debug/ath11k/soc_rx_stats | grep -i pn"
Sample Output:
PN check fail: 210
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IPQ8074 HW has support to verify the PN of the received frames.
For all frames except for fragmented ones, HW checks the PN and
delivers them to the driver. For fragmented frames, driver is
required to do a little more; it has to reassemble the fragments
and then reinject them to the HW for verifying the PN. Currently,
to keep the logic simple, PN verifcation is disabled in HW and is
handled in mac80211 for all the frames (fragmented and unfragmented).
On the contrary, offloading PN Validation to the HW brings important
benefits. It reduces CPU cycles spent on the host CPU for verifying
the same; helps in enabling features which improve performance like
mac80211 fast RX path, enabling multiple REO rings for parallel RX
processing, 802.11 decapsulation offloading. All these features are
dependent on PN offload which in turn is dependent on handling of
the received fragments in the driver.
When TKIP security is used, additional handling is required while
processing the fragments; since MIC is computed on an MSDU in TKIP,
only the last fragment has the MIC info. In this case, driver has to
compute the MIC after reassembly and compare it against the MIC
present in the frame. For this, MICHAEL_MIC kernel crypto library
APIs are used and the dependencies are appropriately set.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for v5.7. Major changes:
ath10k
* support for getting btcoex settings from Device Tree
* support QCA9377 SDIO device
ath11k
* add HE rate accounting
* add thermal sensor and cooling devices
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: ath11k@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to
reconfigure HW's maximum txpower.
This fixes 0dBm txpower setting when user attaches to an interface for
the first time with the following scenario:
ieee80211_do_open()
ath9k_add_interface()
ath9k_set_txpower() /* Set TX power with not yet initialized
sc->hw->conf.power_level */
ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and
raise IEEE80211_CONF_CHANGE_POWER */
ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */
This issue can be reproduced with the following:
$ modprobe -r ath9k
$ modprobe ath9k
$ wpa_supplicant -i wlan0 -c /tmp/wpa.conf &
$ iw dev /* Here TX power is either 0 or 3 depending on RF chain */
$ killall wpa_supplicant
$ iw dev /* TX power goes back to calibrated value and subsequent
calls will be fine */
Fixes: 283dd11994 ("ath9k: add per-vif TX power capability")
Cc: stable@vger.kernel.org
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The CONFIG_ATH5K_AHB could be enabled on ATH25 system without enabling
ATH5K driver itself. This does not make sense because CONFIG_ATH5K_AHB
controls object build within drivers/net/wireless/ath/ath5k/ so enabling
it without CONFIG_ATH5K brings nothing.
Add proper dependency to CONFIG_ATH5K_AHB.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tid of 11a station with WMM disable reported by FW is 0x10 in
tx completion. The tid 16 is mapped to a NULL txq since buffer
MMPDU capbility is not supported. Then 11a station's airtime will
not be registered due to NULL txq check. As a results, airtime of
11a station keeps unchanged in debugfs system.
Mask the tid along with IEEE80211_QOS_CTL_TID_MASK to make it in
the valid range.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.10-00047
Signed-off-by: Yibo Zhao <yiboz@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently rx tid setup is happening for TID 0 and TID 16
during peer setup. And if other TID packets received for
the peer it will be redirected to rx error ring and not through
reo ring. And this rx tid configuration cannot be done
in the rx error ring path since it is a atomic context.
So moving the rx tid setup for all tids during the peer setup.
This is required to enable PN offload functionality to route
all packets through reo ring.
Co-developed-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before this change, after writing "warm_hw_reset" debugfs file, host
will send chip reset command to FW even though FW do not support this
service getting a warning print.
Though there is no FW impact before this change, this patch restricts
chip reset command sent to FW only if FW advertises the support via WMI
service bit.
Removed the redundant check and ath10k_warn() print as well.
New version FW will report chip reset service bit to host. Host allow user
to trigger WLAN chip reset only when fw report this service bit.
For older NON-TLV FW, since it do not report chip reset service bit, host
will not send chip reset command. For older TLV FW, since it report chip
reset service bit, host will send chip reset command.
Tested HW: QCA9984, WCN3990
QCA9984 FW version: WLAN.BL.3.9.0.2-00042-S-1
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When running simulate crash stress test, it happened
"failed to read from address 0x800: -110".
Test steps:
1. Run command continuous
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
2. error happened and it did not begin recovery for long time.
[74377.334846] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[74378.378217] ath10k_sdio mmc1:0001:1: failed to read from address 0x800: -110
[74378.378371] ath10k_sdio mmc1:0001:1: failed to process pending SDIO interrupts: -110
It has sdio errors since it can not read MBOX_HOST_INT_STATUS_ADDRESS,
then it has to do recovery process to recovery ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add hardware parameters for QCA9377 sdio devices, it's now properly supported.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, OTP is downloaded twice in case of "pre-cal-dt"
and "pre-cal-file" to fetch the board ID and takes around
~2 sec more boot uptime.
First OTP download happens in "ath10k_core_probe_fw" and
second in ath10k_core_start. First boot does not need OTP
download in core start when valid board id acquired.
The second OTP download is required upon core stop/start.
This patch skips the OTP download when first OTP download
has acquired a valid board id. This patch also marks board
id invalid in "ath10k_core_stop", which will force the OTP
download in ath10k_core_start and fetches valid board id.
Tested HW: QCA9984
Tested FW: 10.4-3.6-00104
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Call cpu_latency_qos_add/update/remove_request() instead of
pm_qos_add/update/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
With multiple VIFS ath10k, and probably others, tries to find the
minimum txpower for all vifs and uses that when setting txpower in
the firmware.
If a second vif is added and starts to scan, it's txpower is not
initialized yet and it set to zero.
ath10k had a patch to ignore zero values, but then it is impossible
to actually set txpower to zero.
So, instead initialize the txpower to INT_MIN in mac80211, and let
drivers know that means the power has not been set and so should
be ignored.
This should fix regression in:
commit 88407beb1b
Author: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Date: Tue Dec 13 14:55:19 2016 -0800
ath10k: fix incorrect txpower set by P2P_DEVICE interface
Tested on ath10k 9984 with ath10k-ct firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there is WMI command failure, 'peer->sta' was not getting
cleaned up, and mac80211 frees the 'sta' memory, which is causing
the below page fault.
Cleaning up the sta pointer in ath11k whenever peer delete command
is sent.
Unable to handle kernel paging request at virtual address 200080000006a
pgd = ffffffc02a774000
[200080000006a] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
.
.
.
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 4.4.60 #1
Hardware name: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 (DT)
task: ffffffc00083c6d0 ti: ffffffc00083c6d0 task.ti: ffffffc00083c6d0
PC is at ath11k_dp_rx_process_mon_status+0x114/0x4e0 [ath11k]
LR is at ath11k_dp_rx_process_mon_status+0xe8/0x4e0 [ath11k]
pc : [<ffffffbffcf8e544>] lr : [<ffffffbffcf8e518>] pstate: 60000145
sp : ffffffc000833a30
Signed-off-by: Vikas Patel <vikpatel@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PPDU_CTRL type is missing in current pktlog dumps.
PPDU_CTRL is sent on CE5 with len 2560 bytes, current
driver ignores the payload len greter than 2048.
PPDU_CTRL of 2560 bytes is sent in two fragments of len 2028
and 532 bytes, but firmware reports pkt header has length as 2560
for both of the fragments.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In multi AP VAP scenario, when user bring down the interfaces. mac80211 mark
the interface down for the duplicated VAP and removed from the
local->interfaces list. ath11k_mac_get_arvif() is dependent on
ieee80211_iterate_active_interfaces_atomic() API to find the vdev id
in a given radio. In disassociation path, ath11k_mac_get_arvif() not
able to find the given vdev id since that VAP is removed from the
local->interfaces list. since sta_state callback throws error, mac80211 log
the below WARN_ON_ONCE message.
Fixed it by storing the allocated_vdev_map in each radio structure to maintain
the created vdev id bits. so that we can directly mask this against the given
vdev_id to find out the ar from the vdev_id.
WARN LOG:
WARNING: at net/mac80211/sta_info.c:1008
CPU: 2 PID: 2135 Comm: hostapd Not tainted #1
Hardware name: Qualcomm Technologies, Inc. IPQ807x/AP-HK01-C1 (DT)
task: ffffffc03a43d800 ti: ffffffc03a43d800 task.ti: ffffffc03a43d800
PC is at sta_set_sinfo+0x9dc/0xad4 [mac80211]
LR is at sta_set_sinfo+0x9cc/0xad4 [mac80211]
pc : [<ffffffbffce2a008>] lr : [<ffffffbffce29ff8>] pstate: 20000145
sp : ffffffc02cedb5f0
x29: ffffffc02cedb5f0 x28: ffffffc03a43d800
x27: 0000000000000014 x26: 0000000000000001
x25: ffffffc02cfc4000 x24: ffffffc036905508
x23: 0000000000000012 x22: ffffffc02cedb670
x21: ffffffc03bc64880 x20: ffffffc036904f80
x19: ffffffc02ae31000 x18: 00000000b019f3a1
x17: 0000000057f30331 x16: 00000000d8d1998e
x15: 0000000000000066 x14: 393a35383a36343a
x13: 6337203a6e6f6974 x12: 6174732065746169
x11: 636f737361736964 x10: 206f742064656c69
x9 : 6146203a31696669 x8 : 6337203a6e6f6974
x7 : 6174732065746169 x6 : ffffffc0008c33f6
x5 : 0000000000000000 x4 : 0000000000000000
x3 : 0000000000000000 x2 : 00000000ffffff92
x1 : 0000000000000000 x0 : ffffffbffcea1091
---[ end trace 63c4b1c527345d5a ]---
Call trace:
[<ffffffbffce2a008>] sta_set_sinfo+0x9dc/0xad4 [mac80211]
[<ffffffbffce2a2c4>] __sta_info_flush+0xec/0x130 [mac80211]
[<ffffffbffce3dc48>] ieee80211_nan_func_match+0x1a34/0x23e4 [mac80211]
[<ffffffbffcde03e0>] __cfg80211_stop_ap+0x60/0xf0 [cfg80211]
[<ffffffbffcdb6d08>] __cfg80211_leave+0x110/0x150 [cfg80211]
[<ffffffbffcdb6d78>] cfg80211_leave+0x30/0x48 [cfg80211]
[<ffffffbffcdb6fbc>] cfg80211_init_wdev+0x22c/0x808 [cfg80211]
[<ffffffc0000afe28>] notifier_call_chain+0x50/0x84
[<ffffffc0000afefc>] raw_notifier_call_chain+0x14/0x1c
[<ffffffc0004ae94c>] call_netdevice_notifiers_info+0x5c/0x6c
[<ffffffc0004ae96c>] call_netdevice_notifiers+0x10/0x18
[<ffffffc0004aea80>] __dev_close_many+0x54/0xc0
[<ffffffc0004aeb50>] dev_close_many+0x64/0xdc
[<ffffffc0004b0b70>] rollback_registered_many+0x138/0x2f4
[<ffffffc0004b0d4c>] rollback_registered+0x20/0x34
[<ffffffc0004b34b4>] unregister_netdevice_queue+0x68/0xa8
[<ffffffbffce3870c>] ieee80211_if_remove+0x84/0xc0 [mac80211]
[<ffffffbffce3e588>] ieee80211_nan_func_match+0x2374/0x23e4 [mac80211]
[<ffffffbffcdc29e8>] cfg80211_wext_giwscan+0x1000/0x1140 [cfg80211]
[<ffffffbffcb2a87c>] backport_genlmsg_multicast_allns+0x158/0x1b4 [compat]
[<ffffffc0004e0944>] genl_family_rcv_msg+0x258/0x2c0
[<ffffffc0004e09f4>] genl_rcv_msg+0x48/0x6c
[<ffffffc0004dfb50>] netlink_rcv_skb+0x5c/0xc4
[<ffffffc0004e06d8>] genl_rcv+0x34/0x48
[<ffffffc0004df570>] netlink_unicast+0x12c/0x1e0
[<ffffffc0004df9a4>] netlink_sendmsg+0x2bc/0x2dc
[<ffffffc00049a540>] sock_sendmsg+0x18/0x2c
[<ffffffc00049ab94>] ___sys_sendmsg+0x1bc/0x248
[<ffffffc00049ba24>] __sys_sendmsg+0x40/0x68
[<ffffffc00049ba5c>] SyS_sendmsg+0x10/0x20
[<ffffffc000085db0>] el0_svc_naked+0x24/0x28
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath11k_mac_get_ar_by_vdev_id() get protected under rcu lock
and unlock. peer association confirmation event get used this API
without rcu protection, so corrected it.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parse and store the out-of-band rates reported by the FW.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will start using ieee80211_tx_status_ext() so we do not need to track
tx rates inside a struct ieee80211_tx_info. It is currently not possible
to populate that struct with HE rate info anyhow.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns a few times (trimmed for brevity):
../drivers/net/wireless/ath/ath11k/debugfs_sta.c:185:7: warning:
variable 'rate_idx' is used uninitialized whenever 'if' condition is
false [-Wsometimes-uninitialized]
It is not wrong, rate_idx is only initialized in the first if block.
However, this is not necessarily an issue in practice because rate_idx
will only be used when initialized because
ath11k_accumulate_per_peer_tx_stats only uses rate_idx when flags is not
set to RATE_INFO_FLAGS_HE_MCS, RATE_INFO_FLAGS_VHT_MCS, or
RATE_INFO_FLAGS_MCS. Still, it is not good to stick uninitialized values
into another function so initialize it to zero to prevent any issues
down the line.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Link: https://github.com/ClangBuiltLinux/linux/issues/832
Reported-by: ci_notify@linaro.org
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BTCOEX feature is not supported by all QCA4019 chipsets.
Since btcoex enabled by default in firmware, host needs to
enable COEX support depends on the hardware. Enabling it
by default in unsupported hardware will cause some
feature disabled in hardware.
This patch will read btcoex_support flag and
wlan priority gpio pin number from DT. Depends on the
btcoex_support flag value host will expose BTCOEX support
and wlan priority gpio pin number to target.
Testing:
* Tested HW : QCA4019
* Tested FW : 10.4-3.2.1.1-00017
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix warnings which were recently introduced:
drivers/net/wireless/ath/ath10k/ahb.c:462: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/ahb.c:470: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/sdio.c:697: space prohibited before that close parenthesis ')'
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Ftrace is one of the last W^X violators (after this only KLP is
left). These patches move it over to the generic text_poke()
interface and thereby get rid of this oddity. This requires a
surprising amount of surgery, by Peter Zijlstra.
- x86/AMD PMUs: add support for 'Large Increment per Cycle Events' to
count certain types of events that have a special, quirky hw ABI
(by Kim Phillips)
- kprobes fixes by Masami Hiramatsu
Lots of tooling updates as well, the following subcommands were
updated: annotate/report/top, c2c, clang, record, report/top TUI,
sched timehist, tests; plus updates were done to the gtk ui, libperf,
headers and the parser"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (57 commits)
perf/x86/amd: Add support for Large Increment per Cycle Events
perf/x86/amd: Constrain Large Increment per Cycle events
perf/x86/intel/rapl: Add Comet Lake support
tracing: Initialize ret in syscall_enter_define_fields()
perf header: Use last modification time for timestamp
perf c2c: Fix return type for histogram sorting comparision functions
perf beauty sockaddr: Fix augmented syscall format warning
perf/ui/gtk: Fix gtk2 build
perf ui gtk: Add missing zalloc object
perf tools: Use %define api.pure full instead of %pure-parser
libperf: Setup initial evlist::all_cpus value
perf report: Fix no libunwind compiled warning break s390 issue
perf tools: Support --prefix/--prefix-strip
perf report: Clarify in help that --children is default
tools build: Fix test-clang.cpp with Clang 8+
perf clang: Fix build with Clang 9
kprobes: Fix optimize_kprobe()/unoptimize_kprobe() cancellation logic
tools lib: Fix builds when glibc contains strlcpy()
perf report/top: Make 'e' visible in the help and make it toggle showing callchains
perf report/top: Do not offer annotation for symbols without samples
...
There is a spelling mistake in a wcn36xx_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a spelling mistake in a ar5523_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the required USB ID for running SMCWUSBT-G2 wireless adapter (SMC
"EZ Connect g").
This device uses ar5523 chipset and requires firmware to be loaded. Even
though pid of the device is 4507, this patch adds it as 4506 so that
AR5523_DEVICE_UG macro can set the AR5523_FLAG_PRE_FIRMWARE flag for pid
4507.
Signed-off-by: Mert Dirik <mertdirik@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use device_get_match_data() here to simplify the code a bit.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some printks in here don't have newlines at the end, meaning the log
will be sort of hard to read. Add newlines.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linus Torvalds