Print to dmesg when FW error notification is about to be sent
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Interrupt threshold registers may be written to.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usable for debugging, to be able to obtain FW traces
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For performance monitoring, trace time intervals when Tx vring
is idle/not idle. Use CPU cycle counter for this, because jiffies is
too rough, and other precise time measurement methods involve
overhead while get_cycles() should be fast.
This used to provide some estimation for percentage when Tx vring
was idle, i.e. when hardware is under-utilized.
Estimation is not precise because of many reasons - CPU frequency scaling,
grt_cycles() may be per core etc. But still, it is good estimation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
print used/available counters on debugfs;
print to dmesg when Tx vring becomes empty
This aids with performance investigation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
print essential info to dmesg
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_cfg80211_start_ap(), debug print selected data:
- beacon (before and after fix-up)
- crypto parameters
- mark start/stop AP invocation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inform cfg80211 about Tx result
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide 2 files on the debugfs:
- "rxon": write channel (1..4) to open Rx on it, 0 to rxoff
- "tx_mgmt": write binary frame, starting from MAC header
one need to care about turning receiver on/off before/after tx_mgmt
Correct sequence is:
echo $channel > rxon
cat mfmt_frame > tx_mgmt
echo 0 > rxon
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use seperate tx queue for each AC in each channel context and expose
these information to mac80211 to avoid stopping one channel context
leads to stopping the entire traffic for that AC even on other contexts.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the TSF based hardware timer for a channel switch.
Also set up backup software timer, in case the gen timer fails.
This could be caused by a hardware reset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF time might have been updated by the incoming beacon,
need update the channel switch timer to reflect the change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In multi channel context (AP + STA case), adjust the TSF time of
the AP chanctx to keep its beacons at half beacon interval offset
relative to the STA chanctx.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update current offchannel duration during scan or roc request.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a basic state machine for switch channel context
for beacon transmission.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Group and set hw state (opmode, primary_sta, beacon conf) per
channel context instead of whole list of vifs. This would allow
each channel context to run in different mode (STA/AP).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Save TSF in channel context for multiple operating channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retrieve appropriate operating channel context while switching
between operating and off channels.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add channel context operations (add, remove, change, assign and
unassign) to enable support for multiple channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add remain on channel support in order to enable multi-channel
concurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement hw_scan support for enabling multi-channel cuncurrency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving from or entering to active channel context, send out
nullfunc frame to inform to the AP about the presence of station.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Force queueing of all frames that belong to a virtual interface on
a different channel context, to ensure that they are sent on the
correct channel.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel context worker is used to switch to next requested
channel context.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to maintain per-channel ACs list.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel context structure is defined to enable
multi-channel concurrency support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Pull trivial tree changes from Jiri Kosina:
"Usual pile of patches from trivial tree that make the world go round"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
staging: go7007: remove reference to CONFIG_KMOD
aic7xxx: Remove obsolete preprocessor define
of: dma: doc fixes
doc: fix incorrect formula to calculate CommitLimit value
doc: Note need of bc in the kernel build from 3.10 onwards
mm: Fix printk typo in dmapool.c
modpost: Fix comment typo "Modules.symvers"
Kconfig.debug: Grammar s/addition/additional/
wimax: Spelling s/than/that/, wording s/destinatary/recipient/
aic7xxx: Spelling s/termnation/termination/
arm64: mm: Remove superfluous "the" in comment
of: Spelling s/anonymouns/anonymous/
dma: imx-sdma: Spelling s/determnine/determine/
ath10k: Improve grammar in comments
ath6kl: Spelling s/determnine/determine/
of: Improve grammar for of_alias_get_id() documentation
drm/exynos: Spelling s/contro/control/
radio-bcm2048.c: fix wrong overflow check
doc: printk-formats: do not mention casts for u64/s64
doc: spelling error changes
...
Firmware 10.x supports up to 8 virtual AP interfaces, but in a DFS
channel it was possible to create only 7 interfaces as ath10k internal
creates a monitor interface for DFS. Previous vdev map initialization
was missing enough space for 8 + 1 vdevs due to wrong define used and
that's why there was no space for 8th interface. Use the correct define
TARGET_10X_NUM_VDEVS with 10.x firmware to make it possible to create
the 8th virtual interface.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While fixing a bug reported by Avery I went ahead
and added a warning suspecting there might be
something more to the bug. This ended up with
people reporting they see warnings during heavy
traffic. This bought me some time and helped me
understand the problem better - apparently fw/hw
can report a chained msdus as follows: 1 msdu, 1
chained, 1 msdu (0 length).
The patch removes the extra check but leaves the
other change that fixed the original skb_push
panic bug (msdu_chaining was overwritten in an
unfortunate way which made the above example to
be treated as non-chained case).
Reported-by: Yeoh Chun-Yeow <yeohchunyeow@gmail.com>
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Print Kconfig options enabled/disabled in the build.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Print message if no events received. This should not happen.
If it is, it points to the problem in firmware.
Track also cases when multiple events processed in one IRQ
Print information as soon as possible - mbox pointers and
event header right after reading it. This helps to identify potential
problem with memory allocation for the event buffer.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently mac80211 does not support WDS and DFS with channel context
drivers. So advertise these features only when the driver is not
supporting channel context and modparam "use_chanctx" is introduced
for preparing channel context support in ath9k.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of receiving frame with sequence number far greater than current,
wil_release_reorder_frames() will iterate many times over empty buffer.
Optimize this case by checking buffer emptiness and simply update
head_seq_num without iterating.
Suggested-by: Vladimir Shulman <Vladimir.Shulman@Wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use proper format %pad for the dma_addr_t arguments;
prefix %p with 0x, as %p don't print is by itself
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If scan has not finished in some reasonable time (10sec), interpret it as
if firmware error occurs but was not reported. Firmware should report
scan completion for every scan request, so it is error condition indeed.
Perform firmware recovery procedure.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide clear definition of the watermarks for the vring descriptor space.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case there is something fundamentally wrong with the firmware
(example: RF cable disconnected), FW will always crash immediately
after reset. This leads to infinite fw error recovery loop.
Count consecutive unsuccessful error recovery attempts in a short period
of time, and stop doing recovery after some reasonable count.
It is still possible to manually reset fw doing
interface down/up sequence.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obey 802.11 spec that defines max. data size 7920 bytes
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pm_lock is taken twice while syncing HW TSF of p2p vif.
Fix this by taking the lock at caller side.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: fix possible hang on flush" changed the receive code
to always link rx descriptors of processed frames, even when flushing.
In some cases, this leads to flushed rx buffers being passed to the
hardware while rx is already stopped.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make DFS pulse interval calculation independent
from CONFIG_ATH9K_DEBUGFS.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents leaving incomplete scatter-gather
transfer on CE rings which can lead firmware to
crash.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to read invalid state of CE ring
buffer indexes. This could lead to scatter-gather
transfer failure in mid-way and crash firmware
later by leaving garbage data on the ring.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems ath10k firmware gives us no way to know
the rssi for rx-fragments.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW creates self-peer for AP internally.
This prevents ath10k from trying to create
explicit self-peer during hw recovery and thus
prevents a timeout and a warning during teardown:
ath10k: removing stale peer $AP_BSSID from vdev_id 0
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All configuration sequences should be protected
with conf_mutex to avoid concurrent/conflicting
requests.
This should make sure that wep tx key setup is not
performed while hw is restarted (at least).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes sure no further tx requests are
submitted to HTT before driver teardown.
This should prevent invalid pointer/NULL
dereference on htt tx pool in ath10k_htt_tx() in
some cases of heavy traffic.
kvalo: remove the WARN_ON() if conf_mutex is held
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reduces risk of races and prepares for more
hw restart fixes.
It also makes sense to perform teardown after
mac80211 starts its restart routine as it
guarantees it has stopped itself by then
(including tx queues).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes failpath when override AC pdev param
setup fails and makes other pdev params setting
fail as well.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If ath10k was built into the kernel it could stall
booting for 120 seconds by default (60 seconds for
each firmware API variant) waiting for firmware
files before userspace was ready or filesystems
mounted.
Fix this by making the core registering
asynchronous.
This also shoves off about 1 second from boot time
on most systems since the driver is now mostly
initialized in a worker and modprobe takes very
little time to complete.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The tasklet is already guaranteed to be killed on
the teardown path.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will avoid unnecessary forward declaration of
any kind in the future.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents protected flag being stripped from
undecrypted raw sniffed frames when monitor
interface is active.
Reported-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Tested-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The channel_switch_beacon callback is optional, so it doesn't have to
be defined if it's not going to do anything useful with it. Both
ath9k and ath10k define the callback and just returns. This commit
removes them.
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
tmp may be used uninitialized if ath10k_bmi_read_memory() returns
an error.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recently there was a bug discovered that involved
hif_stop() being called twice that ended up with a
double free_irq() call but it only manifested with
multiple MSI interrupts mapping.
Catch this kind of a problem early in driver
regardless of interrupt mapping.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible to call hif_stop() 2 times through
ath10k_htc_connect_init() timeout failpath which
could lead to double free_irq() kernel splat for
multiple MSI interrupt case.
Re-order init sequence to avoid this problem. The
HTC stop shouldn't stop HIF implicitly since it
doesn't implicitly start it. Since the re-ordering
required some functions to be split/removed/renamed
rename a few functions to make more sense while at
it.
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On idle state, sleep timer is scheduled to put the chip into fullsleep.
But during suspend, this timer is scheduled after the chip is moved to
fullsleep forcibily. This is causing below unnecessary error messages
in kernel log during suspend.
ath: phy2: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000
!= 0x00000000
ath: phy2: RX failed to go idle in 10 ms RXSM=0xdeadbeef
ath: phy2: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
DMADBG_7=0xdeadbeef
Reported-by: Arkh4mKn1ght <arkh4mkn1ght@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The keycache index is used to abort transmission for given station
when it goes to sleep state. But the commit "ath9k_hw: Abort transmission
for sleeping station" is not handling multi-key station. Fix that.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DFS pulse interval printing is only available
when CONFIG_ATH9K_DEBUGFS is set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
carl9170_usb_probe() does not handle request_firmware_nowait() failure
that leads to several leaks in this case.
The patch adds all required deallocations.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Verified that target's tx/rx chain register is set appropriately,
and that the tx rate goes down as number of chains
decrease, but I did not actually try to verify antenna
ceased to transmit when disabled.
kvalo: move ar->supp_*_chainmask initialisation to ath10k_mac_register()
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently Oleksij's compile testing was no better than mine initially
was... :-(
Cc: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath9k/htc_drv_txrx.o
drivers/net/wireless/ath/ath9k/htc_drv_txrx.c: In function ‘ath9k_rx_prepare’:
drivers/net/wireless/ath/ath9k/htc_drv_txrx.c:1006:2: warning: passing argument 2 of ‘ath9k_htc_err_stat_rx’ from incompatible pointer type [enabled by default]
ath9k_htc_err_stat_rx(priv, &rx_stats);
^
In file included from drivers/net/wireless/ath/ath9k/htc_drv_txrx.c:17:0:
drivers/net/wireless/ath/ath9k/htc.h:380:20: note: expected ‘struct ath_htc_rx_status *’ but argument is of type ‘struct ath_rx_status *’
static inline void ath9k_htc_err_stat_rx(struct ath9k_htc_priv *priv,
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data transmission to the power save station should be aborted
immediately, whenever the station informs sleep state. Right now
the frames queued into into hardware are being transmitted until
the hardware detects the power save station based excessive retries
of the data frames due to unacknowlegdement. Then remaining frames
are returned with filetered status and might be retried later by
driver or mac80211.
Per WFA certification testing, AP should not send out more than two
frames after processing nullfunc with PM bit set from associated
station. To speed up tx filtering, the pending frames in hardware
queues for given station will be aborted immediately via tx filter
registers. This transmit filters can be ignored if the descriptor
is having invalid destination index or clear destination mask set.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This also propagates through the drivers.
The orinoco driver uses the cfg80211 API structs for internal
bookkeeping, and so needs a (void *) cast that removes the
const - but that's OK because it allocates those pointers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add initial values for JP DFS pattern detector.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sending and receiveing protected managment frames.
Lack of protected flag for received protected action frames
causes report these frames as unprotected robust action frames.
If the driver in AP mode sent frame with protected flag and
CCMP header using IEEE80211_KEY_FLAG_SW_MGMT_TX flag,
the FW encrypted frames once again. From user side all
received SA Query Requests and Responses were skipped and
all protected action frames were sent as malformed packets.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On ARM-based (MSM mach), the pci_assign_resource() is passing
some invalid pointers and leading to L2 cache errors,
what prevents the PCI communication completly.
So far I have not found this funtion to be directly called by
any other wifi driver and did not found this assigning needed
on any other platform. So removing it completely.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be useful for early initialization
debugging, i.e. ROM crashes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes warm reset works upon retry. It might be
related to imperfect warm reset routine, but for
now let's just do the retries.
This should improve the reliability of some chips
that hang/crash with cold reset which is used as a
last resort if warm reset fails.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Warm reset is now able to recover after device
crashes which required a cold reset before.
This should greatly reduce chances of getting data
bus errors or host system freezes due to buggy
cold reset on some chips.
kvalo: use ath10k_pci_soc_*()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During remain on channel request, ANI worker thread is not stopped
before doing hw reset. This is causing kernel crash in
hw_per_calibration. This change ensures that ANI is stopped before
doing chip reset and it will be rescheduled later when the chip is
configured back to home channel and having valid bss.
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently firmware can sometimes report a
sequence with the first rx descriptor saying it's
not the last MSDU. In that case msdu_chaining
value could be overwritten saying it's not a
chained MSDU. This in turn led to skb_push panic
as the frame could be treated as an A-MSDU instead
of a chained MSDU.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
msdu_payId was read before txrx tasklet was killed
so it was possible to end up using an invalid
sk_buff pointer leading to a panic.
Make sure to sanitize rx ring sk_buff pointers and
make the clean up go through all possible entries
and not rely on coherent-DMA mapped u32 index
which could be (in theory) corrupted by the device
as well.
Reported-By: Avery Pennarun <apenwarr@gmail.com>
Reported-By: Ben Greear <greearb@candelatech.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vladimir Kondratiev