Now that rt2x00pci_write_tx_data and rt2x00usb_write_tx_data are similar
we can merge them in a single function in rt2x00queue.c.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to rt2800pci, remove the check for duplicate
register reading, and instead limit the for-loop to
the maximum number of TX entries inside a queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Explicitly enable the usage of fallback rates for
the transmission of frames with rt61pci and rt73usb hardware.
Note that for txdone reporting, only rt61pci is capable of
reporting the fallback rates, for USB it is not possible
to determine the number of retries. However the device will
use the fallback rates, so it might still help in the performance.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of fiddling with the skb->data pointer and thereby risking
out of bounds accesses, properly reserve the space needed in an
skb for descriptors.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Not all the devices require a TX descriptor to be written (i.e. rt2800
device don't require them). Push down the creation of the TX descriptor
to the device drivers so that they can decide for themselves whether
a TX descriptor is to be created.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
(Based on a patch created by Ondrej Zary)
In some circumstances the Ralink devices do not properly go to sleep
or wake up, with timeouts occurring.
Fix this by retrying telling the device that it has to wake up or
sleep.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The handling of tx descriptors for beacons can be simplified by updating
write_tx_desc implementations of each driver to write directly to the
queue entry descriptor instead of to a provided memory area.
This is also a preparation for further clean ups where descriptors are
properly reserved in the skb instead of fiddling with the skb data
pointer.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Where possible, write the tx descriptor words from start to end, to
follow a logical ordering of words.
Where this is not possible (in rt2400pci, rt2500pci and rt61pci) add
a comment as to why word 0 needs to be written last.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The buffer address descriptor word is not part of the TXINFO structure
needed for beacons. The current writing of that word for beacons is
therefore an out-of-bounds write.
Fix this by only writing the buffer address descriptor word for TX
queues.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation to fix rt2800 beaconing.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All of the driver's kick_tx_queue callback functions treat the TX queue
for beacons in a special manner.
Clean this up by integrating the kicking of the beacon queue into the
write_beacon callback function, and let the generic code no longer call
the kick_tx_queue callback function when updating the beacon.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should simply follow what the hardware told us it has done.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And use it consistently in the chipset drivers.
Preparation for further clean ups.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed to wake up the device automatically for receiving beacons,
and is required for proper powersave handling.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The recent rt2800 devices are no longer really identified by their PCI
ID's, but rather by the contents of their CSR0 register. Also for the
other chipsets is the contents of this CSR0 register important.
Change the chipset determination logic to be more aligned with the rt2800
model.
Preparation for the support of rt3070 / rt3090 based devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't set the RT chipset for a device from within the generic PCI/SOC code,
but rather from the individual drivers, so that individual drivers have
more control over what RT chipset is set.
Preparation for chip handling updates for rt2800 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
get_tx_stats() will be removed from mac80211.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let each of them take a struct rt2x00_dev pointer as argument instead of
a mixture of struct rt2x00_chip and struct rt2x00_dev pointers.
Preparation for further clean ups in the rt2x00 chip handling, especially
for rt2800 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've had many reports of rt61pci failures with powersaving enabled.
Therefore, as a stop-gap measure, disable powersaving of the rt61pci
until we have found a proper solution.
Also disable powersaving on rt2800pci as it most probably will show
the same problem.
Cc: stable@kernel.org
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the value of extra_tx_headroom in a central place, rather than in each
of the drivers. This is preparatory for taking alignment space into account
in the TX headroom requested by rt2x00.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the use of whitespace in the initialization of the rt2x00_ops
structures. This is preparatory for a later patch that adds members
to that structure, which require different whitespace alignment.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (rt2800* most notably) cannot set the RF and RT chipset in
the correct order to have the information logging in rt2x00_set_chip
be correct.
Fix this by decoupling the setting of the chipset information from the
logging of the chipset information so that drivers can determine
themselves when all information is set.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As mentioned on the linux-wireless mailing list, the current copyright
statements in the rt2x00 are meaningless, as the rt2x00 project is
not even a formal legal entity. Therefore it is better to replace
the existing copyright statements with copyright statements for the
people that actually wrote the code.
Note: Updated to the best of my knowledge with respect to who
contributed considerable amounts of code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calculated values for the ACK timeout and ACK
consume time are different then the values as
used by the Legacy drivers.
After testing from James Ledwith it appeared that
the calculated values caused a high amount of TX
failures, and the values from the Legacy drivers
were the most optimal to prevent TX failure due to
excessive retries.
The symptoms of this problem:
- Rate control module always falls back to 1Mbs
- Low throughput when bitrate was fixed
Possible side-effects (not confirmed but highly likely)
- Problems with DHCP
- Broken connections due to lack of probe response
This should fix at least:
Kernel bugzilla reports: [13362], [13009], [9273]
Fedora bugzilla reports: [443203]
but possible some additional bugs as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When beacon is being updated to refresh TIM (AP mode), beacon frames are
de-synchronizing (i.e. two neighbor beacon frames - before and after
update - are being transmitted with a wrong time interval).
That is because xxx_write_beacon should disable beacon generation only
while beacon data are being uploaded to the device, but it should not
disable the beacon clock.
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements FIF_PSPOLL filter flag support in rt2x00 drivers,
which has been introduced in mac80211 (see
http://marc.info/?l=linux-wireless&m=124897986330807&w=2).
Signed-off-by: Igor Perminov <igor.perminov@inbox.ru>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unloading rt61pci can leave the device in such state that reloading
rt61pci would fail to reinitialize it. Bogus data would be read from
the EEPROM and the RF version won't be recognized.
It appears that unloading rt61pci with power saving enabled would have
such effect. To initialize the device properly, SOFT_RESET_CSR should
be set to the same value as rt61pci_config_ps() uses to wake up the
device.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a bunch of spelling errors in the rt2x00 drivers
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement set_tim callback for all rt2x00 drivers, this makes the
device wake up powersaving stations properly while in AP mode.
The only way to update the beacon is by simply calling mac80211 and
requesting the new beacon. This means the set_tim() event is mostly the
same as a beacon_done() event which was already defined in rt2x00lib.
Signed-off-by: Stefan Steuerwald <salsasepp@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the input_polldev from rt2x00 and replace it with
the rfkill interface offered by the wiphy structure. This
simplifies the entire rfkill handling in rt2x00 and allows
us to remove the CONFIG_RT2X00_LIB_RFKILL option and always
enables rfkill capabilities.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the last usage of beacon_int inside the iee80211_config
structure from rt2x00. The attempt is a bit hackish, and subject to
change in the future when the entire rt2x00_dev structure is
cleaned up and restructured.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago,
it is about time to remove all usage from the rt2x00 drivers and
use the correct beacon interval configuration through the bss_info
structure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pci_dev->irq and pci_name(pci_dev) access should be limited
to rt2x00pci only. This is more generic and allows a rt2x00 pci
driver to be controlled as PCI device but also as platform driver
(needed for rt2800pci SoC support).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only way rf_write() can be called with word 0 is
when the user sends the wrong word index through debugfs.
However the values which are send through debugfs are
validated using the RF_BASE and RF_SIZE macro values,
the most logical solution is to increase RF_BASE with 4
and decrease RF_SIZE with 4 (RF_SIZE has always been
1 word too big)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The get_firmware_crc() callback function isn't flexible
enough when dealing with multiple firmware versions.
It might in some cases be possible that the firmware
file contains multiple CRC checksums.
Create the check_firmware() callback function where the driver
has complete freedom in how to validate the firmware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
provide rt2x00lib the possibility to kill a particular TX queue.
This can be useful when disabling the radio, but more importantly
will allow beaconing to be disabled when mac80211 requests this
(during scanning for example)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add extra security to the drivers for firmware loading,
check the firmware file length before uploading it to
the hardware. Incorrect lengths might indicate a firmware
upgrade (which is not yet supported by the driver) or
otherwise incorrect firmware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
conf_tx() in rt61pci and rt73usb only have to check once
if the queue_idx indicates a non-WMM queue and break of
the function immediately if that is the case.
Only the WMM queues need to have the TX configuration written
to the registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This modifies hardware flags for powersave to support three different
flags:
* IEEE80211_HW_SUPPORTS_PS - indicates general PS support
* IEEE80211_HW_PS_NULLFUNC_STACK - indicates nullfunc sending in software
* IEEE80211_HW_SUPPORTS_DYNAMIC_PS - indicates dynamic PS on the device
It also adds documentation for all this which explains how to set the
various flags.
Additionally, it fixes a few things:
* a spot where && was used to test flags
* enable CONF_PS only when associated again
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag ENTRY_TXD_OFDM_RATE isn't flexible enough
to indicate which rate modulation should be used for
a frame. This will become a problem when 11n support
is added.
Remove the flag and replace it with an enum value which
can better indicate the exact rate modulation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 2 bits in EEPROM_NIC_TX_RX_FIXED each influence
a different antenna. We might as well split the
definition and directly read the correct bit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restrict drivers to only access link_qual structure during
link tuning. The contents of these fields are for the drivers
and all fields are allowed to be changed to values the driver
considers correct.
This means that some fields need to be moved outside of this
structure to restrict access only to rt2x00link itself.
This allows some code to be moved outside of the rt2x00.h header
and into rt2x00link.c.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The link_tuner() function will always call bbp_read()
at the start of the function. Because this is an
indirect register access has some costs attached
to it (especially for USB hardware).
We already store the value read from the register
into the vgc_level value inside the link structure.
Instead of reading from the register we can read that
field directly and base the tuner on that value.
This reduces the time the registers are locked with
the csr_mutex and speeds up the link_tuner processing.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Listen to IEEE80211_CONF_PS to determine if the device
should drop into powersaving mode. This feature depends
on the dynamic power save functionality in mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers should notify rt2x00lib when they provide
the IV/ICV data. This adds some flexibility to drivers
which can't provide all information.
* rt2500usb provides ICV inside the frame
* rt2800pci doesn't provide IV/ICV
* rt2800usb doesn't provide IV/ICV
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IV and EIV belong to eachother and don't require
2 seperate fields. Instead they can logically be
merged into a single array with size 2.
With this approach we can simplify the code in
rt2x00crypto.c by using a single memcpy() when
copying the iv/eiv data. Additionally we can
move some code out of if-statements because the
if-statement would always be true.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All code which accessed indirect registers was similar
in respect to the for-loop, the given timeout, etc.
Move it into a seperate function, which for PCI drivers
can be moved into rt2x00pci.
This allows us to cleanup the cleanup the code further
by removing the goto statementsand making the codepath
look a bit nicer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Indirect registers require multiple calls to the CSR
register in order to access the indirect registers.
This must be protected under a lock to prevent race
conditions which could cause invalid data to
be returned when reading from the indirect register or silent
failures when writing data to the indirect register.
USB drivers where already protected under a mutex,
so rename the mutex and make PCI drivers use the mutex
as well.
This now means that BBP and RF registers are no longer
accessible in interrupt context. That is not a bad
situation since the slow behavior of accessing
those registers means we don't _want_ to access them
in interrupt context either.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge the callback functions init_txentry() and
init_rxentry(). This makes life in rt2x00lib a
lot simpler and we can cleanup several functions.
rt2x00pci contained "fake" FIELD definitions for
descriptor words. This is not flexible since it
assumes the driver will always have the same field
to indicate if a driver is available or not.
This should be dependent on the driver, and we
should add a callback function for this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move calculation of CSR register offset into rt2x00debug.c
and remove the wrapper functions from each individual driver.
(Except rt2500usb, which still needs to wrap for the
different value type argument).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.
* Remove set_retry_limit callback function, handled
through config()
* Move config_antenna to its own callback function,
it isn't handled by mac80211 anymore
* Use IEEE80211_CONF_CHANGED_* flags and remove manual
checks
* Removed deprecated short slot setting through config()
and put it in config_erp() through which mac80211 now
configures it
* Remove config_phymode() and move contents to config_erp()
since it only managed the basic rates which is now
determined by mac80211 through config_erp().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the rt2x00 driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a crypto key is being removed, rt2x00mac should not
reset the key->hw_key_idx value because that will prevent
the driver from removing the correct key from the hardware.
Furthermore ffz() starts counting at 0 instead of 1, so we don't
need to substract 1 from the resulting value.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There isn't really a good reason to have the LED
configuration options selectable per driver, lets
make it default 'y' and make it depend on the
NEW_LEDS and LEDS_CLASS interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFKILL should be enabled for _all_ hardware whether
or not they feature a rfkill button or not.
Remove driver specific RFKILL configuration options
and make the rt2x00lib version depend on CONFIG_RFKILL
and defaulting to 'y' to make sure it will always
be enabled when RFKILL was enabled.
This also fixes some bugs where RFKILL wasn't initialized
and didn't respond to RFKILL key presses.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.
The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)
Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a module parameter to rt61 and rt73 to disable
HW crypto. The option should only be checked when
determining if the SUPPORT_HW_CRYPTO flag should
be set or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can optimize lna calculation in IRQ context by
calculating most of the value during the config() callback
when most of the value is actually influenced.
This will be required later by rt2800pci and rt2800usb as
well, since they need the lna_gain value during config().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Channel information which is read from EEPROM should
be read into an array containing per-channel information.
This removes the requirement of multiple arrays and makes
the channel handling a bit cleaner and easier to expand.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci supports hardware encryption.
rt61pci supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.
Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.
By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.
After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.
This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a bit of code moving to rt2x00lib within the
TX and RX paths we can now remove a lot of EXPORT_SYMBOL_GPL()
statements. This cleans up the interface between rt2x00lib
and the drivers and has the additional benefit that rt2x00pci
and rt2x00usb are trimmed down in size as well since they
have less to do.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current PCI drivers require a lot of pre-allocated DMA buffers. Reduce this
by using dynamically mapped skb's (using pci_map_single) instead of the pre-
allocated DMA buffers that are allocated at device start-up time.
At the same time move common RX path code into rt2x00lib from rt2x00pci and
rt2x00usb, as the RX paths now are now almost the same.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the same time clean up the device administration a bit, by storing a pointer
to struct device instead of a void pointer that is dependent on the type of
device. The normal PCI and USB subsystem provided macros can be used to convert
the device pointer to the right type.
This makes the rt2x00 driver a bit more type-safe.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The skbs containing the beacons weren't properly cleaned up for rt2400pci, rt2500pci,
rt61pci, and rt73usb. Clean up those skbs in the manner appropriate for each driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data and data_len fields aren't really necessary in struct
skb_frame_desc, as they can be deduced from the skb itself.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX queues shouldn't be kicked after each frame that is put into the
queue. This could cause problems during RTS and CTS-to-self as well
as with fragmentation. In all those cases you want all frames to be
send out in a single burst. Off course we shouldn't let the queue fill
up entirely, thus we introduce a 10% threshold which, when reached,
will force the frames to be send out regardless of the frame.
In addition we should prevent queues to become full in such a way
that the tx() handler can fail. Instead of stopping the queue when
it is full, we should stop it when it is below the threshold.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce code duplication by moving led structure initialization
into a per-driver function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reduce goto usage
* Mark if-statements which are true on hardware error unlikely()
* Cleanup debug messages
This makes the code look nicer and be better optimized since
the chance of hardware errors should be very small.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the pending removal of the tx_control structure
we can merge the RX and TX entry private data structure
in advance. This will temporarily increase the required
memory for the queue, but that overhead will only be limited.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the rxdesc structure is properly memsetted before passed to
the driver. This means we don't have to reinitialize the flags
and dev_flags fields in the drivers again.
This will prevent problems when the rxdone handler is adding
flags in a earlier status and will make the code look nicer
when we are adding more read attributes in the rxdone handler
in the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split rt2x00lib_write_tx_desc() up into a TX descriptor initializor
and TX descriptor writer.
This split is required to properly allow mac80211 to move its
tx_control structure into the skb->cb array.
The rt2x00queue_create_tx_descriptor() function will read all tx control
information and convert it into a rt2x00 TX descriptor information structure.
After that function is complete, we have all information we needed from the
tx control structure and are free to start writing into the skb->cb array
for our own purposes.
rt2x00queue_write_tx_descriptor() will be in charge of really sending
the TX descriptor to the hardware and kicking the TX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde