The IMX219 camera driver is not a clock provider, but merely a clock
consumer, and thus does not need to include <linux/clk-provider.h> and
<linux/clkdev.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Parse device properties and register controls for them using the newly
introduced helpers.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When enumerating the frame sizes, the value sent to
imx219_get_format_code should be fse->code
(the code from the ioctl) and not imx219->fmt.code
which is the code set currently in the driver.
Fixes: 22da1d56e9 ("media: i2c: imx219: Add support for RAW8 bit bayer format")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement the get_selection pad operation for the IMX219 sensor driver.
The supported targets report the sensor's native size, the crop default
rectangle and the crop rectangle.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adds a driver for the 8MPix Sony IMX219 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
8MPix @ 15fps, 1080P @ 30fps (cropped FOV), and 1640x1232 (2x2 binned)
@ 30fps are currently supported.
[Sakari Ailus: make imx219_check_hwcfg static]
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Geert Uytterhoeven