Modifying the pullup state during host mode trig a new enumeration
of attached device. Thus, avoid modifying pullup in host mode.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If dual role configuration is not selected, check and force dr_mode
based on the selected configuration.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ID status change interrupt will not be handled in peripheral only
configuration. So initialize op_state during gadget init.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Correctly update lx_state on gadget connection and disconnection.
When usb cable is disconnected, lx_state must be updated to L3 as
controller could be in power off state.
When usb cable is connected, lx_state must be updated to L0 as
controller is powered.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On a disconnect, dwc2 will kill all remaining urbs from qh list.
urbs are given back to hcd with -ETIMEDOUT status.
Some usb device driver, like mass storage, will unlink all urbs
using usb_hcd_unlink_urb when receiving a negative status different
from -ECONNRESET.
The following flow will then happen:
dwc2_hcd_disconnect()
-> dwc2_kill_all_urbs() try to kill first pending urb.
-> dwc2_host_complete(-ETIMEDOUT)
-> usb_hcd_giveback_urb(-ETIMEDOUT)
-> sg_complete()
-> usb_unlink_urb()
-> usb_put_dev(urb->dev)
-> dwc2_kill_all_urbs() try to kill next pending urb.
-> dwc2_host_complete(-ETIMEDOUT)
-> usb_hcd_giveback_urb(-ETIMEDOUT)
-> NULL pointer dereferencing because urb->dev has been freed for all
urbs of this device.
The root cause of this NULL pointer is to call call usb_unlink_urb()
while we are killing all urbs. To avoid this return urb with
-ECONNRESET status
This issue usually happens while removing mass storage device during
transfer.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On first qh initialization, hsotg->frame_number is not corresponding
to reality. So read it from host controller to get correct value.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Print urb->iso_frame_desc.status after it has been updated using
dwc2_hcd_urb_get_iso_desc_status().
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some high speed mass storage devices fail to enumerate with following
error:
Cannot enable port %i. Maybe the USB cable is bad?
This happens only when the device is plugged while the controller
is in hibernation state. After exiting hibernation, the controller
detects the device as a low speed device and fail to enumerate it.
Problem occurs only if HPRT0.PWR bit is programmed in a too short
delay after exiting hibernation. Dumping hprt register in
_dwc2_hcd_resume() directly after dwc2_exit_hibernation() shows that
HPRT0.LNSTS (D+/D- level) becomes valid approximately 2ms after
exiting hibernation.
Since dwc2_exit_hibernation() is called from atomic context, move the
delay out of this function.
Delay value is experimental and not mentioned in Synopsys
documentation. To be on the safe side 3ms delay is used.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If an interrupt rises during hibernation process, dwc2 will assert
interrupt line to interrupt controller. If interrupt is level
sensitive, interrupt handler will be called in a loop because dwc2
will not be able to clear it while controller is hibernated.
Thus, clear all controller interrupts before hibernation entry.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable host interrupts before synchronising dwc2 irq.
So that interrupts are not generated once controller is stopped.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
GINTSTS.DisconnInt is host only interrupt and should be disable after
dwc2_disable_host_interrupts is called.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case controller is asked to stop while devices are connected,
disconnect all devices and clean up before stopping.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Frame number is reset in hardware after exiting hibernation.
Thus, reset frame_number and ensure qh are queued with correct
sched_frame.
Otherwise, qh->sched_frame may be too high compared to
current frame number (which is 0). This can delay addition of qh in
the list of transfers until frame number reaches qh->sched_frame.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Port can be resumed in bus_resume callback.
In this case, there is no need to drive resume a second time
when hcd ask for it.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If hibernation is supported, resume of devices will be handled in
bus_resume callback.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a device is disconnected, lx_state must not be changed since the
device may be disconnected whereas controller is still powered.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During hcd initialization, hardware accessible flag and lx_state must
be reset to the working state since controller is powered at this stage.
Same logic applied for stop callback.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable controller power and enter hibernation when usb bus is
suspended. A phy driver is required to disable the power of the
controller and detect remote-wakeup or disconnection since the
controller will not be able to detect these in this state.
Once the phy driver detects bus activity, it must call
usb_hcd_resume_root_hub.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
lx_state must be used to reflect controller power state only and not
bus state. Thus add a flag to track state during bus suspend.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
port resume sequence may be used in different places. Create a
function to handle it. Make hprt0 read-modify-write atomic and
clear HPRT0_SUSP for both writes as it is a "read, write-set,
and self-clear (R_WS_SC)" bit. Since the lock is released
between the writes, read hprt0 again.
Since the phy clock is stopped in dwc2_port_suspend(), enable it
here and remove the PCGCTL write from dwc2_hcd_hub_control()
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When entering hibernation hprt0 must be read using dwc2_read_hprt0().
Otherwise, any set hprt0 status bits will be cleared when restoring
hprt0 on exit from hibernation.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fix spelling typo inv various part of sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It's just a lot clearer to use | operator instead of
+ operator.
Caught by coccicheck:
"
drivers/usb/dwc2/gadget.c:2883:26-27: WARNING: sum of probable
bitmasks, consider |
"
Cc: John Youn <John.Youn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Register backup function can be called from atomic context. Instead
of using atomic memory pool, embed backup storage space in
struct dwc2_hsotg.
Also add a valid flag in each struct as NULL pointer can't be used as
the content validity check any more.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To avoid sleep while atomic bugs, allocate qtd before calling
dwc2_hcd_urb_enqueue. No need to pass mem_flags to
dwc2_hcd_urb_enqueue any more as no memory allocations are done in it.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To avoid sleep while atomic bugs, allocate qh before calling
dwc2_hcd_urb_enqueue. qh pointer can be used directly now instead of
passing ep->hcpriv as double pointer.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit db62b9a804 (usb: dwc2: host: don't
use dma_alloc_coherent with irqs disabled)
introduced a build warning by using NULL
as an integer. Fix that by just using 0 instead
of NULL.
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2_hc_nak_intr could be called with a NULL qtd.
Ensure qtd exists before dereferencing it to avoid kernel panic.
This happens when using usb to ethernet adapter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2 may not be able to exit from hibernation if the hardware
does not provide a way to detect resume signalling in this state.
Thus, add the possibility to disable hibernation feature.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As dwc2 pci module is now exporting dwc2 platform device, include
platform.o in dwc2-y and remove USB_DWC2_PLATFORM configuration
option. Driver will be built as two modules, dwc2.ko and dwc2_pci.ko.
dwc2.ko is the new platform driver.
Remove all EXPORT_SYMBOL_GPL as they are not needed any more.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for SetPortFeature(PORT_TEST) for root port.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Jingwu Lin <jingwu.lin@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Align buffer must be allocated using kmalloc since irqs are disabled.
Coherency is handled through dma_map_single which can be used with irqs
disabled.
Reviewed-by: Julius Werner <jwerner@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During urb_enqueue, if the urb can't be queued to the endpoint,
the urb is freed without any spinlock protection.
This leads to memory corruption when concurrent urb_dequeue try to free
same urb->hcpriv.
Thus, ensure the whole urb_enqueue in spinlocked.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Once hub is runtime suspended, dwc2 must resume it
on port connect event.
Else, roothub will stay in suspended state and will
not resume transfers.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update controller state to indicate suspend entry.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If phy driver is present register hcd handle to it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Force argument is not used anymore. Clean up leftovers from
https://lkml.org/lkml/2014/12/9/283
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Inform that device is otg-capable in case of otg configuration.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During vbus session, usb controller needs to exit hibernation if it was
previously in suspend state.
Since controller will be resetted and configured, there is no need
to restore registers.
Moreover, set lx_state to L0 on B session. vbus_session callback may
not be used by all platforms. Thus, controller software state needs
to be set to L0 if the controller detects a valid B session.
Otherwise, lx_state will remain L2 and prevent any request submission.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If usb controller is in partial power down, any write to registers may
cause unpredictable behavior.
Thus, prevent any new request submission once controller is in partial
power down.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Nothing to be done in pm suspend/resume when controller is in L2.
Don't disconnect or reset. State is already saved when putting
controller in hibernation and will be restored on USB bus resume.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ResetDet interrupt is used to detect a reset of the bus
while the controller is suspended.
This may happens for example when using Command Verifier.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So the parameters can be used in both host and gadget modes.
Also consolidate param functions in the core.h
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is required due to an Intel specific hardware issue. Where id-
pin setup causes glitches on the interrupt line when CONIDSTSCHG
interrupt is enabled.
Specify external_id_pin_ctl when an external driver (for example phy)
can handle id change, so that CONIDSTSCHG interrupt can be disabled
from the controller.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During suspend, there could a race condition between ep_queue and
suspend interrupt if lx_state is updated after releasing spinlock in
call_gadget(hsotg, suspend).
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allow controller to enter in hibernation during usb bus suspend and
inform both phy and gadget about the suspended state.
While in hibernation, the controller can't detect the resume condition.
An external mechanism must call usb_phy_set_suspend on resume.
Exit hibernation when controller gets the resume interrupt and inform
only gadget driver about it.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When suspending usb bus, phy driver may disable controller power.
In this case, registers need to be saved on suspend and restored
on resume.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Dump all registers to take a complete snapshot of dwc2 state.
Code is inspired by dwc3/debugfs.c
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Prepare to add more debug code. Moreover, don't save dentry * for
each file in struct dwc2_hsotg as clean up is done with
debugfs_remove_recursive(). s3c_hsotg_delete_debug() is removed
altogether for the same reason.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
msleep(USB_RESUME_TIMEOUT) must be done when the controller drives
the resume. This is true after HPRT0_RES is written.
Moreover, restore the delay after controller power is up.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RqsO
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: generic resume timeout for v4.1
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U+M2
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2-pci driver should be compiled as a module when configured to
do so. If the dwc2-pci is configured as a module but actually
built-in, it can cause build errors due to the fact that the
generic-phy will be allowed to compile as a module causing undefined
references.
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When the HCD is disconnected, the DMA transfers still in-flight were cleaned-up
but the count of available DMA channels (e.g. available_host_channels) was not
reset.
The pool of DMA channels can be depleted when doing unclean
disconnection of USB peripherals, and reaches the point where no
transfer was possible until the next reboot/reload of the driver.
Tested by putting a programmable USB mux on the port and randomly
plugging/unpluging a USB HUB with USB mass-storage key, USB-audio and
USB-ethernet dongle connected to its downstream ports, and also doing the
disconnection early while the devices are still enumerating to get more URBs
in-flight.
After the patch, the devices are still enumerating after thousands of cycles,
while the port was totally dead before.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dwc2-pci driver requires the generic PHY. This fixes undefined
reference issues when it is not selected.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If device is configured to work only in HOST or DEVICE mode, there is
no point in initializing both subdrivers. This patch also fixes
resource leakage if host subdriver fails to initialize.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The pci driver now registers a platform driver, like in dwc3, and lets
its probe function do all the initialization. This allows it to
account for changes to the platform driver that were not added to the
pci driver. Also future changes to the probe function don't have to be
duplicated. This also has the effect of adding device and DRD mode to
the pci driver. Tested on the Synopsys HAPS PCIe platform.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When dwc2 controller detects a disconnect interrupt,
dwc2_hcd_disconnect() should be called immediately to do clean-up
jobs and set port_connect_status_change flag to notify usb hub
driver disconnect status.
Tested-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of
PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h.
Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bGMq
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.20 merge window
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the DWC2 datasheet, the HWCFG1 register stores
the configured endpoint directions for endpoints 0-15 in bit positions
0-31.
==========================
Endpoint Direction (EpDir)
This 32-bit field uses two bits per endpoint to determine the endpoint
direction.
Endpoint
Bits [31:30]: Endpoint 15 direction
Bits [29:28]: Endpoint 14 direction
....
Bits [3:2]: Endpoint 1 direction
Bits[1:0]: Endpoint 0 direction (always BIDIR)
==========================
The DWC2 driver is currently interpreting the contents of the register
as directions for endpoints 1-15 which leads to an error in determining
the configured endpoint directions in the core because the first 2 bits
determine the direction of endpoint 0 and not 1.
This is based on testing/next branch in Felipe's git.
Signed-off-by: Roshan Pius <rpius@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is currently possible to configure the dwc2 driver as built-in
when host mode or dual-role is enabled, but the USB core is
a loadable module. This leads to a link failure:
drivers/built-in.o: In function `_dwc2_hcd_start':
:(.text+0x84538): undefined reference to `usb_hcd_resume_root_hub'
drivers/built-in.o: In function `_dwc2_hcd_urb_dequeue':
:(.text+0x84aa0): undefined reference to `usb_hcd_check_unlink_urb'
:(.text+0x84e4c): undefined reference to `usb_hcd_unlink_urb_from_ep'
:(.text+0x84e74): undefined reference to `usb_hcd_giveback_urb'
drivers/built-in.o: In function `dwc2_assign_and_init_hc':
:(.text+0x86b98): undefined reference to `usb_hcd_unmap_urb_for_dma'
drivers/built-in.o: In function `_dwc2_hcd_urb_enqueue':
:(.text+0x8717c): undefined reference to `usb_hcd_link_urb_to_ep'
:(.text+0x872f4): undefined reference to `usb_hcd_unlink_urb_from_ep'
drivers/built-in.o: In function `dwc2_host_complete':
:(.text+0x875d4): undefined reference to `usb_hcd_unlink_urb_from_ep'
:(.text+0x87600): undefined reference to `usb_hcd_giveback_urb'
drivers/built-in.o: In function `dwc2_hcd_init':
:(.text+0x87ba8): undefined reference to `usb_disabled'
:(.text+0x87d38): undefined reference to `usb_create_hcd'
:(.text+0x88094): undefined reference to `usb_add_hcd'
:(.text+0x880dc): undefined reference to `usb_put_hcd'
drivers/built-in.o: In function `dwc2_hcd_remove':
:(.text+0x8821c): undefined reference to `usb_remove_hcd'
:(.text+0x8823c): undefined reference to `usb_put_hcd'
drivers/built-in.o: In function `dwc2_hc_handle_tt_clear.isra.10':
:(.text+0x88e2c): undefined reference to `usb_hub_clear_tt_buffer'
drivers/built-in.o: In function `dwc2_hcd_qtd_add':
:(.text+0x8b554): undefined reference to `usb_calc_bus_time'
To fix the problem, this patch changes the dependencies so that
dwc2 host mode can only be enabled if either the USB core is
built-in or both USB and dwc2 are modules.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB reset interrupt is no more used to reset the controller.
Thus, reset the controller in pullup callback as described by
Synopsys programming guide. Otherwise enumeration sometimes
fails when usb configuration is switched without physical
disconnection.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Defines are more readable and searchable than constants.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
hsotg->phyif is set in dwc2_gadget_init according to phy interface
width. Use it for configuration instead of hardcoded value.
Moreover, set USB turnaround time according to phy width.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Print debug message according to zlp direction. Always saying
"Sending" is misleading.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pullup doesn't need to be enabled during usb reset since it is
already enabled. This leads to shorter chirp-k duration if done
during usb reset.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a flag to request physical reset of the controller when
s3c_hsotg_core_init_disconnected is called.
During the usb reset, controller must not be fully reconfigured and
resetted. Else this leads to shorter chirp-k duration during
enumeration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, dwc2 requires buffers to be 4 bytes aligned. Use
bounce buffers if they are not.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove dead code as well.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
s3c_hsotg_process_req_feature comments was not correct
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle SET_FEATURE TEST_MODE request sent by the host.
Slightly rework FEATURE request handling to allow parsing
other request types than Endpoint.
Also add a debugfs to change test mode value from user space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When clearing HALT on an endpoint, req->complete of in progress
requests must be called with locks off. New request should only be
started if there is not already a pending request on the endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a remote wakeup happens during bus_suspend, hcd needs to resume
its root hub.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix using the bare number to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 0cf884e819.
Even after applying the follow-on patch at
https://patchwork.kernel.org/patch/5325111
there are still problems with device connect on the Altera SOCFPGA
platform at least. One possible fix would be to add a whitelist
to enable suspend/resume on platforms where it does work correctly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following problem: data transmission in direction
IN break unless the GSNPSID register access is done with spinlock held.
This issue occurs at least in Exynos4412 SoC, probably in many SoC's
from Exynos familly.
The problem is described here:
https://lkml.org/lkml/2014/12/22/185
And there is linux mailing list discussion:
https://lkml.org/lkml/2015/1/14/17
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If usb bus is reset without a physical disconnection, all endpoints
will remain open. Call s3c_hsotg_disconnect() from reset handler to
report a disconnect to gadget framework. hsotg->connected is checked
in s3c_hsotg_disconnect() before processing disconnect.
In some cases, USBRst is seen before EnumDone and after it as well.
So move setting of hsotg->connected to set-address to avoid reporting
extra disconnection in this case.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When booting with id pin grounded, dwc2 default to host mode.
Thus, force device mode prior initializing gadget part.
Else fifo init will fail since fifo values are not correct
in host mode.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This callback informs the driver about the total amount of current it
is allowed to draw. Share this information with the phy so that
current limits can be set for charging for example.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadget must be informed about disconnection when pullup is
removed.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After all endpoints are disabled, fifo_map should have reached 0.
Its a bug if if didn't, so warn about it and reset it to 0 so that
driver can continue using all the fifos.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When selecting different alt setting, s3c_hsotg_ep_enable can be
called with fifo already allocated. Allocate fifo again only if
required and after deallocating the previous fifo.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current algorithm picks the first fifo which is equal to or greater
than the required size. This can result in bigger fifos assigned to
endpoints with smaller maxps. Change the algorithm to pick the
smallest fifo which is greater than or equal to the required size.
Moreover, only use signed variables when required.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This flag is set before sending the zlp. So use present tense instead
of the past tense.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable phy driver to report vbus session. This allows us to remove
D+ pullup when vbus is not present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Can't stay in the loop forever. Break it after timeout.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The warning is probably good but it has false positives in both dma and non-dma
cases. So its not very helpful in either.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to programming guide, zero length packet should be
programmed on its own and should not be counted in DIEPTSIZ.PktCnt
with other packets.
For ep0, this is the zlp for DATA IN stage (if required) and not for
the STATUS stage.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Manage ep0 state in software to add handling of status OUT stage.
Just toggling hsotg->setup in s3c_hsotg_handle_outdone leaves it in
wrong state in 2-stage control transfers.
Moreover, ensure that for setup-packet s3c_hsotg_handle_outdone is
called either from SetupDone or OutDone but not both. Dwc2 ip v3.00a
generates both SetupDone and OutDone on setup packets.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kill_all_requests() can flush the fifo. Call it after disabling the
endpoint.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When matching tx fifo to endpoint, consider all fifos instead of
hard limiting to 8
Moreover, print error in case no fifo could be found.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
< 15 check doesn't show debug information for endpoint 15.
It is possible to have less than 15 endpoints so use limit
provided by hardware configuration.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These members are only occupying space.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As fifo size can vary between SOCs, add possibility to configure
them from device tree. Fifo sizes used by the legacy driver will
be used If they are not provided by the device tree.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Current code does not check endpoint 15 interrupt. Use number
of endpoint configured in hardware instead of the hardcoded value.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
GHWCFG1 provides hardware configuration of each endpoint. Use
it to configure the endpoints instead of assuming all even
endpoint are OUT and all odd endpoints are IN.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* Add an of specific function to parse device node properties.
* Enable dma usage only if device tree property 'g_use_dma' is present.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Do a read-modify-write instead of only setting DMAEn bit.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HBstLen is GAHBCFG[4:1]. Use GAHBCFG_HBSTLEN_SHIFT to write burst-
length at correct position.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In the error path, s3c_hsotg_phy_disable should be called after a
call to s3c_hsotg_phy_enable is made.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, data of the previous setup packet can be read back
from cache because ep0 and ctrl buffers are embedded in struct s3c_hsotg.
Allocate buffers instead of embedding them.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Reviewed-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Only process DOEPINT.XferCompl on data packet as DOEPINTn.SetUp can
occur with or without DOEPINT.XferCompl. When DOEPINT.SetUp occurs
with DOEPINT.XferCompl, only DOEPINT.SetUp needs to be handled.
Moreover, ignore DOEPINT.XferCompl when it occurs with
DOEPINT.StupPktRcvd as driver needs to wait for DOEPINT.SetUp to
continue.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When using DMA, keep fifo empty interrupt disabled. Otherwise
core is flooded by interrupts.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Bind peripheral controller to the phy on udc_start. Unbind on
udc_stop.
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes in simpler way the bug described in [1] and [2]. It
looks like DWC2 is the only UDC driver that doesn't force usb requests
to complete in ep_disable() function. This causes described problem,
because we have no guarantee that all requests will be completed before
unbind of usb function.
To fix this problem we force all requests of disabled endpoint to complete.
Also currently running request is not handled. This allowed to simplify
code of kill_all_requests() function, because 'force' parameter is always
set to true, so we don't need it anymore.
In s3c_hsotg_rx_data() we change function used to print message when active
request is NULL from dev_warn() to dev_dbg(), because such situation is
harmless for driver and now it can take place during normal endpoint
disabling.
[1] https://lkml.org/lkml/2014/12/9/283
[2] https://lkml.org/lkml/2014/12/12/360
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Get PHY parameters from devicetree and power off usb PHY during
system suspend.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes us sure that all requests are completed before we unbind
gadget. There are assumptions in gadget API that all requests have to
be completed and leak of complete can break some usb function drivers.
For example unbind of ECM function can cause NULL pointer dereference:
[ 26.396595] configfs-gadget gadget: unbind function
'cdc_ethernet'/e79c4c00
[ 26.414999] Unable to handle kernel NULL pointer dereference at
virtual address 00000000
(...)
[ 26.452223] PC is at ecm_unbind+0x6c/0x9c
[ 26.456209] LR is at ecm_unbind+0x68/0x9c
(...)
[ 26.603696] [<c033fdb4>] (ecm_unbind) from [<c033661c>]
(purge_configs_funcs+0x94/0xd8)
[ 26.611674] [<c033661c>] (purge_configs_funcs) from [<c0336674>]
(configfs_composite_unbind+0x14/0x34)
[ 26.620961] [<c0336674>] (configfs_composite_unbind) from
[<c0337124>] (usb_gadget_remove_driver+0x68/0x9c)
[ 26.630683] [<c0337124>] (usb_gadget_remove_driver) from [<c03376c8>]
(usb_gadget_unregister_driver+0x64/0x94)
[ 26.640664] [<c03376c8>] (usb_gadget_unregister_driver) from
[<c0336be8>] (unregister_gadget+0x20/0x3c)
[ 26.650038] [<c0336be8>] (unregister_gadget) from [<c0336c84>]
(gadget_dev_desc_UDC_store+0x80/0xb8)
[ 26.659152] [<c0336c84>] (gadget_dev_desc_UDC_store) from
[<c0335120>] (gadget_info_attr_store+0x1c/0x28)
[ 26.668703] [<c0335120>] (gadget_info_attr_store) from [<c012135c>]
(configfs_write_file+0xe8/0x148)
[ 26.677818] [<c012135c>] (configfs_write_file) from [<c00c8dd4>]
(vfs_write+0xb0/0x1a0)
[ 26.685801] [<c00c8dd4>] (vfs_write) from [<c00c91b8>]
(SyS_write+0x44/0x84)
[ 26.692834] [<c00c91b8>] (SyS_write) from [<c000e560>]
(ret_fast_syscall+0x0/0x30)
[ 26.700381] Code: e30409f8 e34c0069 eb07b88d e59430a8 (e5930000)
[ 26.706485] ---[ end trace f62a082b323838a2 ]---
It's because in some cases request is still running on endpoint during
unbind and kill_all_requests() called from s3c_hsotg_udc_stop() function
doesn't cause call of complete() of request. Missing complete() call
causes ecm->notify_req equals NULL in ecm_unbind() function, and this
is reason of this bug.
Similar breaks can be observed in another usb function drivers.
This patch fixes this bug forcing usb request completion in when
s3c_hsotg_ep_disable() is called from s3c_hsotg_udc_stop().
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WYyZ
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.
More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().
DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.
DWC3 got support for two new HW platforms: Exynos7
and AMD.
The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.
Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).
Other than these, the usual set of cleanups and
non-critical fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we have assigned clk=NULL, which is a valid clk, we should not
be returning when a clock node is not provide. Instead, we should return
only when we cannot enable the clock.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Building with bcm2835_defconfig, which has CONFIG_PM_SLEEP=n causes the
following build warning:
drivers/usb/dwc2/platform.c:227:12: warning: 'dwc2_suspend' defined but not used [-Wunused-function]
drivers/usb/dwc2/platform.c:237:12: warning: 'dwc2_resume' defined but not used [-Wunused-function]
Annotate these functions with '__maybe_unused' to prevent the warnings.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Suspend/resume code assumed that the gadget was always started and
enabled to connect to usb bus. This means that the actual state of the
gadget (started/stopped or connected/disconnected) was not correctly
preserved on suspend/resume cycle. This patch fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds mutex, which protects initialization and
deinitialization procedures against suspend/resume methods. This mutex
will be needed by the updated suspend/resume calls, which tracks gadget
state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a call to s3c_hsotg_disconnect() from 'end session'
interrupt (GOTGINT_SES_END_DET) to correctly notify gadget subsystem
about unplugged usb cable. DISCONNINT interrupt cannot be used for this
purpose, because it is asserted only in host mode.
To avoid reporting disconnect event more than once, a disconnect call has
been moved from USB_REQ_SET_ADDRESS handling function to SESSREQINT
interrupt. This way driver ensures that disconnect event is reported
either when usb cable is unplugged or every time the host starts a new
session. To handle devices which has been synthesized without
SRP support, connected state is set in ENUMDONE interrupt.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update DWC2 kconfig and makefile to support dual-role mode. The platform
file will always get compiled for the case where the controller is directly
connected to the CPU. So for loadable modules, dwc2.ko is built for host,
peripheral, and dual-role mode. The PCI bus interface will be called
dwc2_pci.ko and the platform interface module will be called dwc2_platform.ko.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since platform.c will get built for both Host and Gadget, if we leave the
usb_disabled() call in platform.c, it results in the following build error
when (!USB && USB_GADGET) condition is met.
ERROR: "usb_disabled" [drivers/usb/dwc2/dwc2_platform.ko] undefined!
Since usb_disabled() is mostly used to disable USB host functionality, move
the call the host portion for the DWC2 driver.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the dwc2 hcd driver is currently not looking for a clock node during
init, we should not completely fail if there isn't a clock provided.
By assigning clk = NULL, this allows the driver, when configured for dual-role
mode, to be able to continue loading the host portion of the driver when
a clock node is not specified.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make dwc2_handle_common_intr call the gadget interrupt function when operating
in peripheral mode. Remove the spinlock functions in s3c_hsotg_irq as
dwc2_handle_common_intr() already has the spinlocks.
Move the registeration of the IRQ to common code for platform and PCI.
Remove duplicate interrupt conditions that was in gadget, as those are handled
by dwc2 common interrupt handler.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Initialize the USB driver to peripheral mode when a B-Device connector
is attached.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Update suspend/resume to use dev_pm_ops API.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch will aggregate the probing of gadget/hcd driver into platform.c.
The gadget probe funtion is converted into gadget_init that is now only
responsible for gadget only initialization. All the gadget resources are now
handled by platform.c
Since the host workqueue will not get initialized if the driver is configured
for peripheral mode only. Thus we need to check for wq_otg before calling
queue_work().
Also, we move spin_lock_init to common location for both host and gadget that
is either in platform.c or pci.c.
We also move suspend/resume code to common platform code.
Lastly, move the "samsung,s3c6400-hsotg" binding into dwc2_of_match_table.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adds the gadget data structure and appropriate data structure pointers
to the common dwc2_hsotg data structure. To keep the driver data
dereference code looking clean, the gadget variable declares are only available
for peripheral and dual-role mode. This is needed so that the dwc2_hsotg data
structure can be used by the hcd and gadget drivers.
Updates gadget.c to use the dwc2_hsotg data structure and gadget pointers
that have been moved into the common dwc2_hsotg structure.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hcd controller needs bus_suspend/resume, dwc2 controller make
root hub generate suspend/resume signal with hprt0 register
when work in host mode.
After the root hub enter suspend, we can make controller enter
low power state with PCGCTL register.
We also update the lx_state for hsotg state.
This patch has tested on rk3288 with suspend/resume.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch allows the gadget portion of the DWC2 driver to get built when
(!USB && USB_GADGET) condition is encountered.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves calls to phy enable/disable out of spinlock protected
blocks in device suspend/resume to fix incorrect caller context. Phy
related functions must not be called from atomic context. To protect
device internal state from a race during suspend, a call to
s3c_hsotg_core_disconnect() is added under a spinlock, what prevents any
further activity on the usb bus.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves udc initialization from pullup() method to
s3c_hsotg_udc_start(), so that method ends with hardware fully
initialized and left in soft-disconnected state. After this change, the
pullup() method simply clears soft-disconnect start() when called with
is_on=1. For completeness, a call to s3c_hsotg_core_disconnect() has
been added when pullup() method is called with is_on=0, what puts the
udc hardware back to soft-disconnected state.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves phy enable/disable calls from pullup() method to
udc_start/stop functions. This solves the issue related to limited caller
context for PHY functions, because they cannot be called from non-sleeping
context. This is also a preparation for using soft-disconnect feature of
udc controller in pullup() method.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch changes s3c_hsotg_core_init function to leave hardware in
soft disconnect mode, so the moment of coupling the hardware to the usb
bus can be later controlled by the separate functions for enabling and
disabling soft disconnect mode. This patch is a preparation to rework
pullup() method.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes duplicated code and sets last_rst variable in the
function which does the hardware reset.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
that call is completely unnecessary because
usb_del_gadget_udc() already makes sure the
gadget driver is properly unregistered from
the UDC.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Excessive debug messages might cause timing issues that prevent correct
usb enumeration. This patch hides information about USB bus reset to let
driver enumerate fast enough to avoid making host angry. This fixes
endless enumeration and usb reset loop observed with some Linux hosts.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes probe function to match the pattern used elsewhere in
the driver, where power regulators are turned off as the last element in
the device shutdown procedure.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
udc_stop() should clear ->driver pointer unconditionally to let the UDC
framework to work correctly with both registering/unregistering gadgets
and enabling/disabling gadgets by writing to
/sys/class/udc/*hsotg/soft_connect interface.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The unioned u32 is used for clearing etc. Having the number of
bitfield bits add up to more than 32 is broken, even if benign.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
sparse was giving the following warning:
warning: context imbalance in 's3c_hsotg_ep_enable'
- different lock contexts for basic block
we were returning ENOMEM while still holding the spinlock.
The sparse warning was fixed by releasing the spinlock before return.
Cc: <stable@vger.kernel.org> # v3.17
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the part of code that initializes the PHY bus width.
This results in simpler code and removes the need to check whether
the Generic PHY Framework is used.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's handling of DMA buffers for non-aligned transfers
was kind of nuts. For IN transfers, it left the URB DMA buffer
mapped until the transfer completed, then synced it, copied the
data from the bounce buffer, then synced it again.
Instead of that, just call usb_hcd_unmap_urb_for_dma() to unmap
the buffer before starting the transfer. Then no syncing is
required when doing the copy. This should also allow handling of
other types of mappings besides just dma_map_single() ones.
Also reduce the size of the bounce buffer allocation for Isoc
endpoints to 3K, since that's the largest possible transfer size.
Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clip max_transfer_size to 65535 for host. dwc2_hc_setup_align_buf()
allocates coherent buffers with this size, and if it's too large we
can exhaust the coherent DMA pool.
Tested on Raspberry Pi and Altera SOCFPGA.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device is stopped or suspended clock is not needed so we
can disable it for this time.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because we have not enough memory to have each TX FIFO of size at least
3072 bytes (the maximum single packet size with 3 transactions per
microframe), we create four FIFOs of lenght 1024, and four of length
3072 bytes, and assing them to endpoints dynamically according to
maxpacket size value of given endpoint.
Up to now there were initialized 16 TX FIFOs, but we use only 8 IN
endpoints, so we can split available memory for 8 FIFOs to have more
memory for each one.
It needed to do some small modifications in few places in code, because
there was assumption that TX FIFO numbers assigned to endpoints are the
same as the endpoint numbers, which is not true since we have dynamic
FIFO assigning.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Print warning if FIFOs are configured in such a way that they don't fit
into the SPRAM available on the s3c hsotg module.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DWC2/s3c-hsotg debug messages are really useless for typical user,
so hide them behind dev_dbg().
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust the debug text to the name of the printed variable.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I'm seeing problems with a d-link dwcl-g122 wifi dongle that
someone sent me. There are reports of other wifi dongles with the
same/similar problem. The devices appear to be NAKing to the point
of confusing the dwc2 driver completely.
The attached patch helps with my d-link dwl-g122 - it's adapted
from the Raspberry Pi dwc_otg driver, which is a modified version
of the Synopsys vendor driver. The error recovery is still valid
after the patch, I think.
Cc: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8df438571c.
This patch breaks building dwc2 driver in gadget mode at samsung
platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e006fee6ec.
This patch causes build break. Modifications in Makefile and Kconfig have
no connection with driver code.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endpoint 0 should not be disabled, so we start loop counter from number 1.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes kernel panic/interrupt storm/etc issues if bootloader
left s3c-hsotg module in enabled state. Now interrupt handler is enabled
only after proper configuration of hardware registers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This leads to potential spinlock recursion in composite framework, other
udc drivers also don't call it directly from pullup method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes possible freeze caused by infinite loop in interrupt
context.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the Generic PHY Framework a NULL phy is considered to be a valid phy
thus the "if (hsotg->phy)" check does not give us the information whether
the Generic PHY Framework is used.
In addition to the above this patch also removes phy_init from probe and
phy_exit from remove. This is not necessary when init/exit is done in the
s3c_hsotg_phy_enable/disable functions.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is removed s3c_hsotg_phy_disable is called three times
instead of once. This results in decreasing of the phy reference counter
below zero and thus consecutive inserts of the module fails.
This patch removes calls to s3c_hsotg_phy_disable from s3c_hsotg_remove
and s3c_hsotg_udc_stop.
s3c_hsotg_udc_stop is called from udc-core.c only after
usb_gadget_disconnect, which in turn calls s3c_hsotg_pullup, which
already calls s3c_hsotg_phy_disable.
s3c_hsotg_remove must be called only after udc_stop, so there is no
point in disabling phy once again there.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Cc: stable <stable@vger.kernel.org> # 3.16
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the "samsung,s3c6400-hsotg" binding as the probe function in the gadget
driver will get removed when the dual-role driver is implemented.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update DWC2 kconfig and makefile to support dual-role mode. The platform
file will always get compiled for the case where the controller is directly
connected to the CPU. So for loadable modules, only dwc2.ko is needed.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the "dr_mode", the otg controller can work as
device role and host role. Some boards always want to use host mode
and some other boards want to use gadget mode. We use the dts setting
to set dwc2's mode, rather than fixing it to whatever hardware says.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation for GNPTXFSIZ says that "For host mode, this field
is always valid." Since we're already switching to host mode for
HPTXFSIZ, let's also read GNPTXFSIZ in host mode.
On an rk3288 SoC, without this change we see this at bootup:
dwc2 ff580000.usb: gnptxfsiz=00100400
dwc2 ff580000.usb: 128 invalid for host_nperio_tx_fifo_size. Check HW configuration.
After this change we see:
dwc2 ff580000.usb: gnptxfsiz=04000400
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add compatible data for dwc2 controller found on
rk3066, rk3188 and rk3288 processors from rockchip.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the default EP max packet value as 8 bytes, because in the case
of low-speed, 'ep_mps' is not set. Thus, the default value of 'ep_mps'
should be considered for the case of low-speed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux-2.6/drivers/usb/dwc2/gadget.c: In function 's3c_hsotg_irq_enumdone':
linux-2.6/drivers/usb/dwc2/gadget.c:1904: warning: 'ep_mps' may be used uninitialized in this function
Acked-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file and folder movements resulted in the incorrect reference.
So for better code maintainability, let's remove it.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checkpatch errors as belows.
ERROR: open brace '{' following function declarations go on the next line
ERROR: space required before the open parenthesis '('
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2 IP on the SOCFPGA cannot use the default HW configured
FIFO sizes. The total FIFO depth as read from GHWCFG3 reports 0x1f80 or 8064
32-bit words. But the GRXFSIZ, GNPTXFSIZ, and HPTXFSIZ register defaults
to 0x2000 or 8192 32-bit words. So the driver cannot just use the fifo sizes
as read from those registers.
For platforms that face the same issue, this commits sets the RX, periodic TX,
and non-periodic TX fifo size to those that are recommended v2.93a spec for
the DWC2 IP. Implements Method #2 from the Synopsys v2.93a spec for the DWC2.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though the IP supports Descriptor DMA mode, it does not support SPLIT
transactions in this mode. So the driver, in its currently form, will not
support LS/FS devices when connected to a HS Hub if Descriptor DMA mode is
enabled.
So we should just default to disable descriptor dma mode.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
%pad notation automatically prints in hexadecimal format (with '0x'), so remove
the unneeded '0x' to avoid a '0x0x' string.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse warns about the __le16 wValue from the USB SetAddress
command being used without converting it to CPU endianness. Fix
that, and also add a bit of defensive masking of the received
wValue before using it.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves the data structures that are in the s3c-hsotg
source into core.h. This is a necessary step towards unifying
the s3c-hsotg and dwc2 into a single DRD.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
[ jh,rb,fb - For gadget part only: ]
Tested-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[ pz - Tested host part only. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moves the s3c-hsotg driver into the dwc2 directory and uses the
dwc2 defines in hw.h. Renames s3c-hsotg.c to gadget.c.
NOTE: You can build both host and peripheral as a dynamically
linked module, but be aware that if you insmod dwc2_gadget, then
rmmod it, then insmod dwc2 and dwc2_platform for host mode, this
will not work. As the step to rmmod dwc2_gadget.ko will turn off
the clock to the USB IP. The dwc2 host driver currently does not
look to turn on a clock yet. A patch to fix that will be coming
soon.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
[ jh,rb - For gadget part only: ]
Tested-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
[ pz: Folded Kconfig/Makefile changes, which were originally in
a separate patch, into this one, to avoid a build breakage.
Modified Kconfig/Makefile changes a bit. Tested host part only. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation of combining the dwc2/s3c-hsotg driver in a single
DRD driver, the defines in dwc2/hw.h needs to get updated so that
the s3c-hsotg driver can use them.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
[ jh,rb - For gadget part only: ]
Tested-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
[ pz - Tested host part only. ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a couple of places, we were checking qtd->urb for NULL after
we had already dereferenced it. Fix this by moving the check to
before the dereference.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the spec for the DWC2 controller, when the PRTINT interrupt fires,
the application must clear the appropriate status bit in the Host Port Control
and Status register to clear this bit.
When disconnecting an A-cable when the dwc2 host driver, the PRTINT fires, but
only the GINTSTS_PRTINT status is cleared, no action is done with the HPRT0
register. The HPRT0_ENACHG bit in the HPRT0 must also be poked to correctly
clear the GINTSTS_PRTINT interrupt.
I am seeing this behavoir on v2.93 of the DWC2 IP. When I disconnect an OTG
A-cable adapter, the PRTINT interrupt fires when the DWC2 is in device mode
and is never cleared.
This patch adds the function to read the HPRT0 register when the PRTINT fires
and the dwc2 IP has already transitioned to device mode. This function is only
clearing the HPRT0_ENACHG bit for now, but can be modified to handle more.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
[ paulz: modified patch to preserve HPRT0_ENA bit ]
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.
The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.
Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: Andre Heider <a.heider@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit beb7e592bc "staging: dwc2: add check on dwc2_core_reset
return" broke the B -> A role switching on OTG-enabled platforms.
This commit fixes it.
Reported-by: Dinh Nguyen <dinguyen@altera.com>
Tested-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add usb_disabled() check to prevent kernel oops when booting with "nousb"
in the cmdline:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at bus_add_device+0xe0/0x18c
LR is at device_add_groups+0x1c/0x20
...
[<c02191c0>] (bus_add_device) from [<c0217130>] (device_add+0x41c/0x538)
[<c0217130>] (device_add) from [<c023b1d4>] (usb_new_device+0x270/0x35c)
[<c023b1d4>] (usb_new_device) from [<c0241174>] (usb_add_hcd+0x4fc/0x760)
[<c0241174>] (usb_add_hcd) from [<c0254ce0>] (dwc2_hcd_init+0x434/0x510)
[<c0254ce0>] (dwc2_hcd_init) from [<c02594f4>] (dwc2_driver_probe+0x130/0x170)
[<c02594f4>] (dwc2_driver_probe) from [<c021bbd0>] (platform_drv_probe+0x28/0x58)
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of people.)
USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdjwIACgkQMUfUDdst+ylBIQCgkRoR8lJc0L5lZ3fugIJL4IzZ
j6AAn0nBLP6VI0cvUEi3TcrPTzv4MEuL
=Yb+I
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of
people). USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues"
* tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (318 commits)
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
usb: chipidea: need to mask INT_STATUS when write otgsc
usb: chipidea: put hw_phymode_configure before ci_usb_phy_init
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
usb: chipidea: add freescale imx28 special write register method
usb: ehci: add freescale imx28 special write register method
usb: core: check for valid id_table when using the RefId feature
usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set
usb: core: bail out if user gives an unknown RefId when using new_id
usb: core: allow a reference device for new_id
usb: core: add sanity checks when using bInterfaceClass with new_id
USB: image: correct spelling mistake in comment
USB: c67x00: correct spelling mistakes in comments
usb: delete non-required instances of include <linux/init.h>
usb:hub set hub->change_bits when over-current happens
Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"
xhci: Set scatter-gather limit to avoid failed block writes.
xhci: Avoid infinite loop when sg urb requires too many trbs
usb: gadget: remove unused variable in gr_queue_int()
...
The DWC2 driver should now be in good enough shape to move out of
staging. I have stress tested it overnight on RPI running mass
storage and Ethernet transfers in parallel, and for several days
on our proprietary PCI-based platform.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>