When monitor mode is enabled, this will make b43legacy read out
the full 64-bit MAC time from the chip for each received packet.
This patch has been ported from b43.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use initialized_var() to properly fix a bogus gcc warning.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM94311MCG rev 02 chip has an 802.11 core with revision 13 and
has not been supported until now. The changes include the following:
(1) Add the 802.11 rev 13 device to the ssb_device_id table to load b43.
(2) Add PHY revision 9 to the supported list.
(3) Change the 2-bit routing code for address extensions to 0b10 rather
than the 0b01 used for the 32-bit case.
(4) Remove some magic numbers in the DMA setup.
The DMA implementation for this chip supports full 64-bit addressing with
one exception. Whenever the Descriptor Ring Buffer is in high memory, a
fatal DMA error occurs. This problem was not present in 2.6.24-rc2 due
to code to "Bias the placement of kernel pages at lower PFNs". When
commit 44048d70 reverted that code, the DMA error appeared. As a "fix",
use the GFP_DMA flag when allocating the buffer for 64-bit DMA. At present,
this problem is thought to arise from a hardware error.
This patch has been tested on my system and by Cédric Caumont
<icare40@hotmail.com>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restart the hardware on too many PHY TX errors. A thousand PHY TX errors
per 15 seconds means we won't be able to recover for sure.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes it can be useful to see the FCS, especially when
bad-FCS frames are shown. Pass the FCS to mac80211 and let
it worry about snipping it off when required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When monitor mode is enabled, this will make b43 read out the
full 64-bit MAC time from the chip for each received packet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* only shift eventcause once
* convert mac events to decimal, as this is what the firmware
manual uses in section 6.1, too
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ability to specify channels to scan via debugfs
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ability to specify number of probes via debugfs
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make two functions in the TX packet path emit
their debug messages with LBS_DEB_TX, not LBS_DEB_MAIN.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change debug output codes from LBS_DEB_JOIN to LBS_DEB_ASSOC
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves re-works the implementation of event subscription
via debugfs. For this:
* it tells cmd.c and cmdresp.c about CMD_802_11_SUBSCRIBE_EVENT
* removes lots of low-level cmd stuff from debugfs.c
* create unified functions to read/write snr, rssi, bcnmiss and
failcount
* introduces #define's for subscription event bitmask values
* add a function to search for a specific element in an IE
(a.k.a. TLV)
* add a function to find out the size of the TLV. This is needed
because lbs_prepare_and_send_command() has an argument for a
data buffer, but not for it's lengths and TLVs can be, by
definition, vary in size.
* fix a bug where it was not possible to disable an event
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New typedefs are usually frowned upon. This patch changes
libertas_adapter -> struct libertas_adapter
libertas_priv -> struct libertas_priv
While passing, make everything checkpatch.pl-clean that gets touches.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Requires firmware version 5.110.19.p0 or newer, available here:
http://dev.laptop.org/pub/firmware/libertas/
Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The transmit and receive traffic as soon as the mesh interface is
brought up.
Test case 1: Bring up only the mesh interface and ping. No need for
any iwconfig commands on the main interface.
$ ifconfig msh0 192.168.5.3
$ iwconfig msh0 channel X
$ ping 192.168.5.2
If ping succeeds, PASS
Test case 2: Associate with the main interface, and turn off AP. Mesh
interface should not lose connectivity.
$ iwconfig eth0 mode managed essid "my_ssid"
$ ifconfig msh0 192.168.5.3
$ ping 192.168.5.2
<turn off access point>
If ping continues uninterrupted, PASS
This feature requires firmware version 5.110.19.p0 or newer, available
here: http://dev.laptop.org/pub/firmware/libertas/
Signed-off-by: Ashish Shukla <ashishs@marvell.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I think it was pretty obvious what fields in if_usb_driver are...
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Do not reset libertas devices upon module unload. We're unloading
the module, we're not killing off devices.
2) Instead, reset libertas devices inside if_usb_disconnect, as we're
killing off interfaces and so on.
3) Resetting via disconnect callback means we no longer need to keep
track of probed libertas devices; kill off that list (and its wonderful
lack of locking..), as well.
Drop a useless comment as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by chloubs on IRC
zd1211 chip 157e:300a v4810 high 00-11-e0 AL7230B_RF pa0 g----
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to be working smoothly now. Let's not hold back the mac80211
transition any further. This patch ports the existing driver from softmac
to mac80211.
Many thanks to everyone who helped out with the porting efforts.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the debug output of all association stuff clearer by:
* adding some lbs_deb_enter()/lbs_deb_leave() calls
* printing the return level in one place
* lower-casing some string
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies the namespace of variables, functions defines
and structures. It does:
- rename libertas_XXX to lbs_XXX
- rename LIBERTAS_XXX to lbs_XXX
- rename wlan_XXX to lbs_XXX
- rename WLAN_XXX to LBS_XXX (but only those that were
defined in libertas-local *.h files, e.g. not defines
from net/ieee80211.h)
While passing, I fixed some checkpatch.pl errors too.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Problem identified by Miguel Botón <mboton.lkml@gmail.com>, alternate
solution suggested by Zhu Yi <yi.zhu@intel.com>, patch by me. :-)
Cc: Miguel Botón <mboton.lkml@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old, now unused, data structures and SPROM extraction routines
are removed.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b43legacy driver is modified to use the new SPROM structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b43 driver is modified to use the new SPROM structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The b44 driver is changed to use the new SPROM data structure.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In disagreement with the SPROM specs, revision 3 devices appear to have
moved the MAC address.
Change ssb to handle the revision 4 SPROM, which is a different size.
This change in size is handled by adding a new variable to the ssb_sprom
struct and using it whenever possible. For those routines that do not
have access to this structure, a 'u16 size' argument is added.
The new PCI_ID for the BCM4328 is also added.
Testing of the Revision 4 SPROM, which is used on the BCM4328, was done
by Michael Gerdau <mgerdau@tiscali.de>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SPROM's for various devices utilizing the Sonics Silicon Backplane come
with various revisions. The Revision 2 SPROM inherited the data layout of 1, and
Revision 3 inherited the layout of 2. The first instance of Revision 4 has
now been found in a BCM4328 wireless LAN card. This device does not inherit any
layout from previous versions. Although it was possible to create a data
structure that kept all the old layouts, we decided to start fresh, keep only
those SPROM variables that are used by the drivers that utilize ssb, and to
do the conversion in such a manner that neither compilation or execution will
be affected if a bisection lands in the middle of these changes, while keeping
the patches as small as possible.
In this patch, the sprom structures are changed while maintaining the old ones.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2400pci, rt2500pci and rt61 require different
txdone handling, but the code that pushes the frame
upstream and cleans up the entry is identical to
all of them.
This will create the function rt2x00pci_txdone()
to remove the duplicate code.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes a bug that enables RXON_FLG_TGG_PROTECT_MSK erroneously
for A mode in the erp_ie_changed mac80211 callback.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use uninitialized_var() to avoid the following bogus warning:
CC [M] drivers/net/wireless/b43/debugfs.o
drivers/net/wireless/b43/debugfs.c: In function ‘b43_debugfs_read’:
drivers/net/wireless/b43/debugfs.c:355: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix dependencies for built-in b43legacy.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also fix Zhu Yi's name.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes the unused function to fix a recursive bug caused
by namespace change.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prefix all symbols with iwl3945_ or iwl4965_ and thus allow building
the driver into the kernel. Also remove all the useless default
statements in Kconfig while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the iwl4965 problem for "Can not find a suitable rate
issues." by making rs_switch_to_mimo and rs_switch_to_siso functions
return -1 when CONFIG_IWL4965_HT is not selected. They used to return 0,
which means we can switch to HT rate causing the rate scale problem and
the error message.
The patch also fix another bug reported by Ben Cahill that it uses wrong
value for max_success_limit.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace 0x8086 with PCI_VENDOR_ID_INTEL for PCI_DEVICE declaration.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix my copyright notices in b43 and b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite and sync A PHY initialization with specs, thus allowing for further
work to be done on 802.11a support. Note that A PHY initialization involves
G PHYs as well.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */
This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up
Fix this by always re-allocating the rfkill stuff before register.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a consistent naming scheme for the ops.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the retry limits provided by mac80211.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SGI IP28 machines would need special treatment (enable adding addtional
wait states) when accessing memory uncached. To avoid this pain I changed
the driver to use only cached access to memory.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Don't enable RX/TX without a link (if possible)
Don't enable RX/TX of packets until we have a link, since there's a chance
we'll just get RX frame errors, etc.
The case where we don't have a PHY we can't do much about: Just enable
it and deal with errors as they come in.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Print warning when not attaching to a PHY
Print a warning on the console when not connecting to a phy for an interface.
It turns out to be a pretty common problem when someone gets the MDIO info
wrong in their device tree, resulting in the macs running at a fixed 1Gbit FD.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: Remove SKB copy/recycle logic
It doesn't really buy us much, since copying is about as expensive
as the allocation in the first place. Just remove it for now.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi_mac: SKB unmap optimization
Avoid touching skb_shinfo() in the unmap path, since it turns out to
normally cause cache misses and delays. instead, save number of fragments
in the TX_RING_INFO structures since that's all that's needed anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Johannes Berg