This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device. The device doesn't like to be asked for
its interface strings.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: adam ? <adam3337@wp.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the number of ports present on the SoC/board is not the maximum
and that the platform data is not filled with all data, there is
an easy way to mess the PIO setup for this interface.
This quick fix addresses mis-configuration in USB host platform data
that is common in at91 boards since commit 0ee6d1e (USB: ohci-at91:
change maximum number of ports) that did not modified the associatd
board files.
Reported-by: Klaus Falkner <klaus.falkner@solectrix.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [3.4+]
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>. It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b69cc67205 added support for the E-861. After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.
Compiled, but only actually tested on the E-861 and C-867.
Signed-off-by: Éric Piel <piel@delmic.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, rebind_workers() and idle_worker_rebind() are two-way
interlocked. rebind_workers() waits for idle workers to finish
rebinding and rebound idle workers wait for rebind_workers() to finish
rebinding busy workers before proceeding.
Unfortunately, this isn't enough. The second wait from idle workers
is implemented as follows.
wait_event(gcwq->rebind_hold, !(worker->flags & WORKER_REBIND));
rebind_workers() clears WORKER_REBIND, wakes up the idle workers and
then returns. If CPU hotplug cycle happens again before one of the
idle workers finishes the above wait_event(), rebind_workers() will
repeat the first part of the handshake - set WORKER_REBIND again and
wait for the idle worker to finish rebinding - and this leads to
deadlock because the idle worker would be waiting for WORKER_REBIND to
clear.
This is fixed by adding another interlocking step at the end -
rebind_workers() now waits for all the idle workers to finish the
above WORKER_REBIND wait before returning. This ensures that all
rebinding steps are complete on all idle workers before the next
hotplug cycle can happen.
This problem was diagnosed by Lai Jiangshan who also posted a patch to
fix the issue, upon which this patch is based.
This is the minimal fix and further patches are scheduled for the next
merge window to simplify the CPU hotplug path.
Signed-off-by: Tejun Heo <tj@kernel.org>
Original-patch-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <1346516916-1991-3-git-send-email-laijs@cn.fujitsu.com>
This doesn't make any functional difference and is purely to help the
next patch to be simpler.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
When adding a blackhole or a prohibit route, they were handling like classic
routes. Moreover, it was only possible to add this kind of routes by specifying
an interface.
Bug already reported here:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=498498
Before the patch:
$ ip route add blackhole 2001::1/128
RTNETLINK answers: No such device
$ ip route add blackhole 2001::1/128 dev eth0
$ ip -6 route | grep 2001
2001::1 dev eth0 metric 1024
After:
$ ip route add blackhole 2001::1/128
$ ip -6 route | grep 2001
blackhole 2001::1 dev lo metric 1024 error -22
v2: wrong patch
v3: add a field fc_type in struct fib6_config to store RTN_* type
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows code to handle the PCIe AER capability.
The PCI callbacks for error handling/reset/recovery already exist in be2net
and have been tested with EEH/ppc.
This patch has been tested using the aer-inject tool.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using list_move_tail() instead of list_del() + list_add_tail().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes this build error:
net/ipv6/netfilter/nf_nat_l3proto_ipv6.c: In function 'nf_nat_ipv6_csum_recalc':
net/ipv6/netfilter/nf_nat_l3proto_ipv6.c:144:4: error: implicit declaration of function 'csum_ipv6_magic' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.
The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.
The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.
Cc: <stable@vger.kernel.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed duplicate definition for SGE_PF_KDOORBELL, SGE_INT_ENABLE3,
PCIE_MEM_ACCESS_OFFSET registers.
Moved the register field definitions around the register definition.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Reviewed-by: Sivakumar Subramani <sivasu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4 driver has duplicate definitions of registers which will be removed. This
patch updates the RDMA/cxgb4 driver accordingly.
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Reviewed-by: Sivakumar Subramani <sivasu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when the NIC duplex state is DUPLEX_UNKNOWN it is exported as
full through sysfs, this patch adds support for DUPLEX_UNKNOWN. It is
handled the same way as in ethtool.
Signed-off-by: Nikolay Aleksandrov <naleksan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 144d56e910
("tcp: fix possible socket refcount problem") is missing
the IPv6 part. As tcp_release_cb is shared by both protocols
we should hold sock reference for the TCP_MTU_REDUCED_DEFERRED
bit.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DRM drivers appear to be missing the .compat_ioctl file
operation entry necessary for 32-bit application compatibility.
This patch uses drm_compat_ioctl for all drivers which don't have
their own, and which are using drm_ioctl for .unlocked_ioctl.
This leaves drivers/gpu/drm/psb/psb_drv.c unchanged; it has a custom
.unlocked_ioctl and will presumably need a custom .compat_ioctl as
well.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
This reverts commit 5d65878d7031b6c39054b282faceff406bb2fda9.
The upper layers call usbnet_start_xmit() with a valid skb.
However cdc_ncm abuses this method by calling it with NULL
to trigger IO for the aggregated private skb holding erlier
packets. Until cdc_ncm is fixed, the check for NULL must
be reintroduced.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.
To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console feature's write routing is unsafe on SMP with
the startup/shutdown call.
There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()
The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.
Add a spin_lock for startup/shutdown/console_write routing.
This patch is a port from Freescale's Android kernel.
Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.
Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.
[ balbi@ti.com: slight improvement to commit log ]
This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.
Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Add support for genl "tcp_metrics". No locking
is changed, only that now we can unlink and delete
entries after grace period. We implement get/del for
single entry and dump to support show/flush filtering
in user space. Del without address attribute causes
flush for all addresses, sadly under genl_mutex.
v2:
- remove rcu_assign_pointer as suggested by Eric Dumazet,
it is not needed because there are no other writes under lock
- move the flushing code in tcp_metrics_flush_all
v3:
- remove synchronize_rcu on flush as suggested by Eric Dumazet
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this patch is for the v3.6 release cycle. Benoît Locher fixed a repeated frame
bug in the mcp251x driver. He implemented the workaround suggested by the
errata sheet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the ioremap_nocache variant of the ioremap API in
order to make sure our memory will be marked uncachable.
This patch should be backported to kernels as old as 3.4, that contain
the commit 3429e91a66 "usb: host: xhci:
add platform driver support".
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.
If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.
As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.
For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.
If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.
Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).
This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.
This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset. The kernels will need to
contain both commit 10d674a82e "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd37d "usb: Add support for root hub
port status CAS". The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.
Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.
I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.
This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d "USB: xhci: BIOS handoff
and HW initialization."
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
The intent was to test whether the flag was set.
This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This patch fixes a race condition that results in memory
corruption when using cleancache.
The race exists between the zcache shrinker handler,
shrink_zcache_memory() and cleancache_get_page().
In most cases, the shrinker will both evict a zbpg
from its buddy list and flush it from tmem before a
cleancache_get_page() occurs on that page. A subsequent
cleancache_get_page() will fail in the tmem layer.
In the rare case that two occur together and the
cleancache_get_page() path gets through the tmem
layer before the shrinker path can flush tmem,
zbud_decompress() does a check to see if the zbpg is a
"zombie", i.e. not on a buddy list, which means the shrinker
is in the process of reclaiming it. If the zbpg is a zombie,
zbud_decompress() returns -EINVAL.
However, this return code is being ignored by the caller,
zcache_pampd_get_data_and_free(), which results in the
caller of cleancache_get_page() thinking that the page has
been properly retrieved when it has not.
This patch modifies zcache_pampd_get_data_and_free() to
convey the failure up the stack so that the caller of
cleancache_get_page() knows the page retrieval failed.
This needs to be applied to stable trees as well.
zcache-main.c was named zcache.c before v3.1, so
I'm not sure how you want to handle trees earlier
than that.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the interface is down, the hardware is powered off.
However, the suspend handler currently tries to send host sleep commands
(when wakeup params are set) in this configuration, causing a system hang
when going into suspend (the commands will never complete).
Avoid this by detecting this situation and simply returning from
the suspend handler without doing anything special.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On our system (ARM Cortex-M3 SOC running linux-2.6.33)
frequent crashes were observed in the rt2800usb module
because of the invalid length of the received packet (3392,
46920...). This patch adds the sanity check on the packet
legth. Also, changed WARNING to ERROR in rt2x00lib_rxdone()
so that the bad packet condition would be noticed.
The fix was tested on the latest compat-wireless-3.5.1-1-snpc.
Cc: stable@vger.kernel.org
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.
Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register is 16 bits wide, not 32.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an RT3572 based device.
Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_cfg80211_get_station requests the RSSI from
the device. The complete structure used needs to be cleared
before sending the request to firmware. Otherwise the request
fails filling the logs with "Could not get rssi (-2)" messages.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On both rx and tx there is was a race condition on the queueing
of usb requests. When for example frame gets submitted it is
possible that complete function gets called even before
usb_submit_urb() returns. As a result it is possible that usb
requests get losts, which was noticed on OMAP4 pandaboard
platform. This patch fixes the race condition.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
URB_ZERO_PACKET should only be set or bulk OUT and this condition
is checked with a WARN_ON in usb_submit_urb(). This patch fixes
brcmfmac to get rid of this warning filling the logs.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB part of the brcmfmac did a dev_kfree_skb() that resulted
in a warning in net/core/skbuff.c:
Jul 11 04:53:33 lb-bun-10 kernel: [53282.667745] WARNING: at
net/core/skbuff.c:490 skb_release_head_state+0xcc/0xe0()
The brcmutil modules provides brcmu_pkt_buf_free_skb() which takes
the context into account. This patch makes use of this function
instead of dev_kfree_skb().
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.
On many newer devices, the calibration is assumed to be done with PA
linearization enabled.
Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Re-train if the calibrated PA linearization curve is out of bounds
(affects AR933x and AR9485).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to the vendor driver v2.6.0.1, during the rf register init the SRAM
voltage should be increased to 1.35V and after 1ms decreased back to 1.2V. This
patch adds the field setting of LDO_CFG0_LDO_CORE_VLEVEL accordingly.
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we send a command to firmware, we assumed that cmd_size
will be always less than or equal to the structure size of
host_cmd_ds_command. However, this is no longer true after
we added AP support. There are some AP commands that Custom
IE TLVs are included in command buffer, hence the cmd_size
gets enlarged by the TLV data. We need to increase the skb
length for the extra data.
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap_fixes_a_3.6rc/20120904110254/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=R0kV
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a-for-3.6rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes
Some hwmod, clockdomain, am335x fixes against v3.6-rc4.
Test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap_fixes_a_3.6rc/20120904110254/
Alan Stern