The call to set_machine_constraints() in regulator_register(), will
attempt to get the voltage for the regulator. If a regulator is in
bypass will fail to get the voltage (ie. it's bypass voltage) and
hence register the regulator, because the supply for the regulator has
not been resolved yet.
To fix this, add a call to regulator_resolve_supply() before we call
set_machine_constraints(). If the call to regulator_resolve_supply()
fails, rather than returning an error at this point, allow the
registration of the regulator to continue because for some regulators
resolving the supply at this point may not be necessary and it will be
resolved later as more regulators are added. Furthermore, if the supply
is still not resolved for a bypassed regulator, this will be detected
when we attempt to get the voltage for the regulator and an error will
be propagated at this point.
If a bypassed regulator does not have a supply when we attempt to get
the voltage, rather than returing -EINVAL, return -EPROBE_DEFER instead
to allow the registration of the regulator to be deferred and tried
again later.
Please note that regulator_resolve_supply() will call
regulator_dev_lookup() which may acquire the regulator_list_mutex. To
avoid any deadlocks we cannot hold the regulator_list_mutex when calling
regulator_resolve_supply(). Therefore, rather than holding the lock
around a large portion of the registration code, just hold the lock when
aquiring any GPIOs and setting up supplies because these sections may
add entries to the regulator_map_list and regulator_ena_gpio_list,
respectively.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To make the code more compat and centralized, this patch add a
unified function - regulator_ops_is_valid. So we can add
some extra checking code easily later.
Signed-off-by: WEN Pingbo <pingbo.wen@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The public functions to acquire a regulator, such as regulator_get(),
internally look-up the regulator from the list of regulators that have
been registered with the regulator device class. The registration of
a new regulator with the regulator device class happens before the
regulator has been completely setup. Therefore, it is possible that
the regulator could be acquired before it has been setup successfully.
To avoid this move the device registration of the regulator to the end
of the regulator setup and update the error exit path accordingly.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During the resolution of a regulator's supply, we may attempt to enable
the supply if the regulator itself is already enabled. If enabling the
supply fails, then we will call _regulator_put() for the supply.
However, the pointer to the supply has not been cleared for the
regulator and this will cause a crash if we then unregister the
regulator and attempt to call regulator_put() a second time for the
supply. Fix this by clearing the supply pointer if enabling the supply
after fails when resolving the supply for a regulator.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The function regulator_register_resolve_supply() is called from the
context of class_for_each_dev() (during the regulator registration) to
resolve any supplies added. regulator_register_resolve_supply() will
return an error if a regulator's supply cannot be resolved and this will
terminate the loop in class_for_each_dev(). This means that we will not
attempt to resolve any other supplies after one has failed. Hence, this
may delay the resolution of other regulator supplies until the failing
one itself can be resolved.
Rather than terminating the loop early, don't return an error code and
keep attempting to resolve any other supplies for regulators that have
been registered.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are debugfs entries for voltage and current, but not for
the constraint flags. It's useful for debugging to be able to
see what these flags are so this patch adds a new debugfs file.
We can't use debugfs_create_bool for this because the flags are
bitfields, so as this needs a special read callback they have been
collected into a single file that lists all the flags.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
suspend_prepare can be called during regulator init time also, where
the mutex is not locked yet. This causes a false lockdep warning.
To avoid the problem, remove the lockdep assertion from the function
causing the issue. An alternative would be to lock the mutex during
init, but this would cause other problems (some APIs used during init
will attempt to lock the mutex also, causing deadlock.)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we acquire a shareable enable GPIO on probe we do so with the
regulator_list_mutex held. However when we release the GPIOs we do this
immediately after dropping the mutex meaning that the list could become
corrupted. Move the release into the locked region to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
device_register() is calling ->get_voltage() as part of it's sysfs attribute
initialization process, and this functions might need to know the regulator
constraints to return a valid value.
This is at least true for the pwm regulator driver (when operating in
continuous mode) which needs to know the minimum and maximum voltage values
to calculate the current voltage:
min_uV + (((max_uV - min_uV) * dutycycle) / 100);
Move device_register() after set_machine_constraints() to make sure those
constraints are correctly initialized when ->get_voltage() is called.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Stephen Barber <smbarber@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator is in bypass mode it is functioning as a switch
returning the voltage set in the regulator will not give the voltage
being output by the regulator as it's just passing through its supply.
This means that when we are getting the voltage from a regulator we
should check to see if it is in bypass mode and if it is we should
report the voltage from the supply rather than that which is set on the
regulator.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
[treding@nvidia.com: return early for bypass mode]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5e3ca2b349 ("regulator: Try to resolve regulators supplies on
registration") added a call to regulator_resolve_supply() within
regulator_register() where the regulator_list_mutex is held. This causes
a deadlock to occur on the Tegra114 Dalmore board when the palmas PMIC
is registered because regulator_register_resolve_supply() calls
regulator_dev_lookup() which may try to acquire the regulator_list_mutex
again.
Fix this by releasing the mutex before calling
regulator_register_resolve_supply() and update the error exit path to
ensure the mutex is released on an error.
[Made commit message more legible -- broonie]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This aids in debugging problems triggered by the regulator core applying
its constraints, we could potentially crash immediately after updating
the voltage if the constraints are buggy.
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
moved the regulator supplies lookup logic from the regulators registration
to the regulators get time.
Unfortunately, that changed the behavior of the regulator core since now a
parent supply with a child regulator marked as always-on, won't be enabled
unless a client driver attempts to get the child regulator during boot.
This patch tries to resolve the parent supply for the already registered
regulators each time that a new regulator is registered. So the regulators
that have child regulators marked as always on will be enabled regardless
if a driver gets the child regulator or not.
That was the behavior before the mentioned commit, since parent supplies
were looked up at regulator registration time instead of during child get.
Since regulator_resolve_supply() checks for rdev->supply, most of the times
it will be a no-op. Errors aren't checked to keep the possible out of order
dependencies which was the motivation for the mentioned commit.
Also, the supply being available will be enforced on regulator get anyways
in case the resolve fails on regulators registration.
Fixes: 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # 4.1+
Currently we only attempt to set the voltage during constraints
application if an exact voltage is specified. Extend this so that if
the currently set voltage for the regulator is outside the bounds set in
constraints we will move the voltage to the nearest constraint, raising
to the minimum or lowering to the maximum as needed. This ensures that
drivers can probe without the hardware being driven out of spec.
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently due to a wrongly resolved merge conflict between two
branches, which contained the same commit, the commit contents
partially was added two times in a row.
This change reverts the latter wrong inclusion of commit 909f7ee0b5
("regulator: core: Add support for active-discharge configuration").
The first applied commit 670666b9e0 ("regulator: core: Add support
for active-discharge configuration") is not touched.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_resolve_supply() function checks if a supply has been
associated with a regulator to avoid enabling it if that is not the
case.
But the supply was already looked up with regulator_resolve_supply()
and set with set_supply() before the check and both return on error.
So the fact that this statement has been reached means that neither
of them failed and a supply must be associated with the regulator.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This problem was introduced by:
commit daad134d66 ("regulator: core: Request GPIO before creating
sysfs entries")
The error path was not updated correctly after moving GPIO registration
code and in case regulator_ena_gpio_free failed, device_unregister() was
called even though device_register() was not yet called.
This problem breaks the boot at least on all Tegra 32-bit devices. It
will also crash each device that specifices GPIO that is unavaiable at
regulator_register call. Here's error log I've got when forced GPIO to
be invalid:
[ 1.116612] usb-otg-vbus-reg: Failed to request enable GPIO10: -22
[ 1.122794] Unable to handle kernel NULL pointer dereference at
virtual address 00000044
[ 1.130894] pgd = c0004000
[ 1.133598] [00000044] *pgd=00000000
[ 1.137205] Internal error: Oops: 5 [#1] SMP ARM
and here's backtrace from KDB:
Exception stack(0xef11fbd0 to 0xef11fc18)
fbc0: 00000000 c0738a14 00000000 00000000
fbe0: c0b2a0b0 00000000 00000000 c0738a14 c0b5fdf8 00000001 ef7f6074 ef11fc4c
fc00: ef11fc50 ef11fc20 c02a8344 c02a7f1c 60000013 ffffffff
[<c010cee0>] (__dabt_svc) from [<c02a7f1c>] (kernfs_find_ns+0x18/0xf8)
[<c02a7f1c>] (kernfs_find_ns) from [<c02a8344>] (kernfs_find_and_get_ns+0x40/0x58)
[<c02a8344>] (kernfs_find_and_get_ns) from [<c02ac4a4>] (sysfs_unmerge_group+0x28/0x68)
[<c02ac4a4>] (sysfs_unmerge_group) from [<c044389c>] (dpm_sysfs_remove+0x30/0x5c)
[<c044389c>] (dpm_sysfs_remove) from [<c0436ba8>] (device_del+0x48/0x1f4)
[<c0436ba8>] (device_del) from [<c0436d84>] (device_unregister+0x30/0x6c)
[<c0436d84>] (device_unregister) from [<c0403910>] (regulator_register+0x6d0/0xdac)
[<c0403910>] (regulator_register) from [<c04052d4>] (devm_regulator_register+0x50/0x84)
[<c04052d4>] (devm_regulator_register) from [<c0406298>] (reg_fixed_voltage_probe+0x25c/0x3c0)
[<c0406298>] (reg_fixed_voltage_probe) from [<c043d21c>] (platform_drv_probe+0x60/0xb0)
[<c043d21c>] (platform_drv_probe) from [<c043b078>] (driver_probe_device+0x24c/0x440)
[<c043b078>] (driver_probe_device) from [<c043b5e8>] (__device_attach_driver+0xc0/0x120)
[<c043b5e8>] (__device_attach_driver) from [<c043901c>] (bus_for_each_drv+0x6c/0x98)
[<c043901c>] (bus_for_each_drv) from [<c043ad20>] (__device_attach+0xac/0x138)
[<c043ad20>] (__device_attach) from [<c043b664>] (device_initial_probe+0x1c/0x20)
[<c043b664>] (device_initial_probe) from [<c043a074>] (bus_probe_device+0x94/0x9c)
[<c043a074>] (bus_probe_device) from [<c043a610>] (deferred_probe_work_func+0x80/0xcc)
[<c043a610>] (deferred_probe_work_func) from [<c01381d0>] (process_one_work+0x158/0x454)
[<c01381d0>] (process_one_work) from [<c013854c>] (worker_thread+0x38/0x510)
[<c013854c>] (worker_thread) from [<c013e154>] (kthread+0xe8/0x104)
[<c013e154>] (kthread) from [<c0108638>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@tieto.com>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_attr_is_visible (which is a .is_visible callback of
regulator_dev_group attribute_grpup) checks rdev->ena_pin to decide if
"status" file should be present in sysfs. This field is set at the end
of regulator_ena_gpio_request so it has to be called before
device_register() otherwise this test will always fail, causing "status"
file to not be visible.
Since regulator_attr_is_visible also tests for is_enabled() op, this
problem is only visible for regulators that does not define this
callback, like regulator-fixed.c.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@tieto.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we now free the constraints in regulator_dev_release we will still
call free on the constraints pointer even if we went down an error
path in regulator_register, because it is only allocated after the
device_register. As such we no longer need to free rdev->constraints
on the error paths, so this patch removes said frees.
Fixes: 29f5f4860a ("regulator: core: Move more deallocation into class unregister")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Originally queue_delayed_work() used to negative error codes or 0 and 1
on success depending if the work was queued or not. It caused a lot of
bugs where people treated all non-zero returns as failures so we changed
it to return bool instead in d4283e9378 ('workqueue: make queueing
functions return bool'). Now it never returns failure.
Checking for negative values causes a static checker warning since it is
impossible based on the bool type.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fa731ac7ea ("regulator: core: avoid unused variable warning")
introduced a subtle change in how supplies are locked. Where previously
code was always locking the regulator of the current iteration, the new
implementation only locks the regulator if it has a supply. For any
given power tree that means that the root will never get locked.
On the other hand the regulator_unlock_supply() will still release all
the locks, which in turn causes the lock debugging code to warn about a
mutex being unlocked which wasn't locked.
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Fixes: Fixes: fa731ac7ea ("regulator: core: avoid unused variable warning")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The latest workaround for the lockdep interface's not using the second
argument of mutex_lock_nested() changed the loop missed locking the last
regulator due to a thinko with the loop termination condition exiting
one regulator too soon.
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As noticed by Geert Uytterhoeven, my patch to avoid a harmless build warning
in regulator_lock_supply() was total crap and introduced a real bug:
> [ BUG: bad unlock balance detected! ]
> kworker/u4:0/6 is trying to release lock (&rdev->mutex) at:
> [<c0247b84>] regulator_set_voltage+0x38/0x50
we still lock the regulator supplies, but not the actual regulators,
so we are missing a lock, and the unlock is unbalanced.
This rectifies it by first locking the regulator device itself before
using the same loop as before to lock its supplies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 716fec9d1965 ("[SUBMITTED] regulator: core: avoid unused variable warning")
Signed-off-by: Mark Brown <broonie@kernel.org>
The second argument of the mutex_lock_nested() helper is only
evaluated if CONFIG_DEBUG_LOCK_ALLOC is set. Otherwise we
get this build warning for the new regulator_lock_supply
function:
drivers/regulator/core.c: In function 'regulator_lock_supply':
drivers/regulator/core.c:142:6: warning: unused variable 'i' [-Wunused-variable]
To avoid the warning, this restructures the code to make it
both simpler and to move the 'i++' outside of the mutex_lock_nested
call, where it is now always used and the variable is not
flagged as unused.
We had some discussion about changing mutex_lock_nested to an
inline function, which would make the code do the right thing here,
but in the end decided against it, in order to guarantee that
mutex_lock_nested() does not introduced overhead without
CONFIG_DEBUG_LOCK_ALLOC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9f01cd4a91 ("regulator: core: introduce function to lock regulators and its supplies")
Link: http://permalink.gmane.org/gmane.linux.kernel/2068900
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it possible to use the bulk API with optional supplies, by allowing
the consumer to marking supplies as optional in the regulator_bulk_data.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we need to read voltages of parents as part of setting supply
voltages we need to be able to do get_voltage() internally without
taking locks so reorganize the locking to take locks on the full tree on
entry rather than as we recurse when called externally.
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Until now changing the voltage of a regulator only ever effected the
regulator itself, but never its supplies. It's a common pattern though
to put LDO regulators behind switching regulators. The switching
regulators efficiently drop the input voltage but have a high ripple on
their output. The output is then cleaned up by the LDOs. For higher
energy efficiency the voltage drop at the LDOs should be minimized. For
this scenario we need to propagate the voltage change to the supply
regulators. Another scenario where voltage propagation is desired is
a regulator which only consists of a switch and thus cannot regulate
voltages itself. In this case we can pass setting voltages to the
supply.
This patch adds support for voltage propagation. We do voltage
propagation when the current regulator has a minimum dropout voltage
specified or if the current regulator lacks a get_voltage operation
(indicating it's a switch and not a regulator).
Changing the supply voltage must be done carefully. When we are
increasing the current regulators output we must first increase the
supply voltage and then the regulator itself. When we are decreasing the
current regulators voltage we must decrease the supply voltage after
changing the current regulators voltage.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
_regulator_call_set_voltage has code to translate a minimum/maximum
voltage pair into a selector. This code is useful for others aswell,
so create a regulator_map_voltage function.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The unlocked version will be needed when we start propagating voltage
changes to the supply regulators.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The unlocked version will be needed when we start propagating voltage
changes to the supply regulators.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each regulator_dev is locked with its own mutex. This is fine as long
as only one regulator_dev is locked, but makes lockdep unhappy when we
have to walk up the supply chain like it can happen in
regulator_get_voltage:
regulator_get_voltage ->
mutex_lock(®ulator->rdev->mutex) ->
_regulator_get_voltage(regulator->rdev) ->
regulator_get_voltage(rdev->supply) ->
mutex_lock(®ulator->rdev->mutex);
This causes lockdep to issue a possible deadlock warning.
There are at least two ways to work around this:
- We can always lock the whole supply chain using the functions
introduced with this patch.
- We could store the current voltage in struct regulator_rdev so
that we do not have to walk up the supply chain for the
_regulator_get_voltage case.
Anyway, regulator_lock_supply/regulator_unlock_supply will be needed
once we allow regulator_set_voltage to optimize the supply voltages.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When resolving regulator-regulator supplies we ignore probe deferral
returns from regulator_dev_lookup() (such as are generated for DT when
we can see a supply is registered) and just fall back to the dummy
regulator if there are full constraints (as is the case for DT). This
means that probe deferral is broken for DT systems, fix that by paying
attention to -EPROBE_DEFER return codes like we do -ENODEV.
A further patch will simplify this further, this is a minimal fix for
the specific issue.
Fixes: 9f7e25edb1 (regulator: core: Handle full constraints systems when resolving supplies)
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonnie@kernel.org>
Cc: stable@vger.kernel.org
As we are already registering a device with regulator_class for each
regulator device, regulator_list is redundant and can be replaced with
calls to class_find_device() and class_for_each_device().
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ret pointer passed to regulator_dev_lookup is only filled with a
valid error code if regulator_dev_lookup returned NULL. Currently
regulator_resolve_supply checks this ret value before it checks if a
regulator was returned, this can result in valid regulator lookups being
ignored.
Fixes: 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The same error print exists 4 times in the regulator core
<rdev>: operation not allowed
Unfortunately, seeing this in the dmesg is not very informative.
Add what type of operation is not allowed to the message so that
these errors are unique, hopefully pointing developers in the
right direction
<rdev>: drms operation not allowed
<rdev>: voltage operation not allowed
<rdev>: current operation not allowed
<rdev>: mode operation not allowed
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been a busy release for regmap. By far the biggest set of
changes here are those from Markus Pargmann which implement support for
block transfers in smbus devices. This required quite a bit of
refactoring but leaves us better able to handle odd restrictions that
controllers may have and with better performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV6cZyAAoJECTWi3JdVIfQM3sH/RSygzRIOoOuvro0U3qd4+nM
qLzpuZNtuAP7xNc5yJZiixz1S6PqUNl+pK/u58s6x10GWDGsWZY6E0Lg94lYmfhA
26jqWSzrMHp42x+ZN7btLExzPTVnvRerrjtj4mqz6t4yun9SzqVymaZTUZ1hqPHB
qxSNHs3rHPiqiEWpQKJXb+5dazYYJCbOUrlivxJCk60+ns1N88cA71aY+5/zq5uy
36e0iYe3s+lv0lptedarFCf9p7o1E6EQzhvEMfyquGXtvq8fl7Qdeo7riRFQ8Iiy
sygCb3AYuZIiqnOC7+90xkr2Oq0iwdJUD91A9sl/SRiwgItG9jW03bWNHYIhQyk=
=CbGt
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for regmap.
By far the biggest set of changes here are those from Markus Pargmann
which implement support for block transfers in smbus devices. This
required quite a bit of refactoring but leaves us better able to
handle odd restrictions that controllers may have and with better
performance on smbus.
Other new features include:
- Fix interactions with lockdep for nested regmaps (eg, when a device
using regmap is connected to a bus where the bus controller has a
separate regmap). Lockdep's default class identification is too
crude to work without help.
- Support for must write bitfield operations, useful for operations
which require writing a bit to trigger them from Kuniori Morimoto.
- Support for delaying during register patch application from Nariman
Poushin.
- Support for overriding cache state via the debugfs implementation
from Richard Fitzgerald"
* tag 'regmap-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (25 commits)
regmap: fix a NULL pointer dereference in __regmap_init
regmap: Support bulk reads for devices without raw formatting
regmap-i2c: Add smbus i2c block support
regmap: Add raw_write/read checks for max_raw_write/read sizes
regmap: regmap max_raw_read/write getter functions
regmap: Introduce max_raw_read/write for regmap_bulk_read/write
regmap: Add missing comments about struct regmap_bus
regmap: No multi_write support if bus->write does not exist
regmap: Split use_single_rw internally into use_single_read/write
regmap: Fix regmap_bulk_write for bus writes
regmap: regmap_raw_read return error on !bus->read
regulator: core: Print at debug level on debugfs creation failure
regmap: Fix regmap_can_raw_write check
regmap: fix typos in regmap.c
regmap: Fix integertypes for register address and value
regmap: Move documentation to regmap.h
regmap: Use different lockdep class for each regmap init call
thermal: sti: Add parentheses around bridge->ops->regmap_init call
mfd: vexpress: Add parentheses around bridge->ops->regmap_init call
regmap: debugfs: Fix misuse of IS_ENABLED
...
We were checking rdev->supply for NULL after dereferencing it. Lets
check for rdev->supply along with _regulator_is_enabled() and call
regulator_enable() only if rdev->supply is not NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When calling regulator_set_load, regulator_check_drms prints and returns
an error if the regulator device's flag REGULATOR_CHANGE_DRMS isn't set.
drms_uA_update, however, bails out without reporting an error.
Replace the error print with a debug level print so that we don't get
such prints when the underlying regulator doesn't support DRMS.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Failure to create a debugfs node is not an error, but we print a
warning upon failure to create the node. Downgrade this to a
debug printk so that we're quiet here. This allows multiple
drivers to request a CPU's regulator so that CPUfreq and AVSish
drivers can coexist.
The downside of this approach is that whoever gets to debugfs first
the others who come later to not have any debugfs attributes associated
with them.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_list has exactly the same contents as the list that the
driver core maintains of regulator_class members so is redundant. As a
first step in converting over to use the class device list convert our
iteration in late_initcall() to use the class device iterator.
Signed-off-by: Mark Brown <broonie@kernel.org>
We really ought to be using the class dvice lifetime management features
more than we are rather than open coding them so take a step towards that
by moving some of the simplest deallocations to the dev_release() function.
Signed-off-by: Mark Brown <broonie@kernel.org>
When we release a regulator we need to remove references to it from the
rdev which means locking the rdev. Currently we also free resources
associated with the regulator inside the rdev lock but there is no need
to do this, we can reduce the region the lock is held by restricting it
to just actions that affect the rdev.
Signed-off-by: Mark Brown <broonie@kernel.org>
When removing a regulator we hold regulator_list_mutex in order to
ensure the regualtor doesn't become removed again. However we only need
to protect the list until we remove the regulator from the list so move
the unlock earlier to reduce the locked region.
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can automatically shut down when they detect an
over current event. Add an op (set_over_current_protection) and a
DT property + constraint to support this capability.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_resolve_supply() function calls set_supply() which in turn
calls create_regulator() to allocate a supply regulator.
If an error occurs after set_supply() succeeded, the allocated regulator
has to be freed before propagating the error code.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator is unregistered with regulator_unregister(), a call to
regulator_put() is made for its input supply if there is one. This does
a module_put() to decrement the refcount of the module that owns the
supply but there isn't a corresponding try_module_get() in set_supply()
to make the calls balanced.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When resolving device supplies if we fail to look up the regulator we
substitute in the dummy supply instead if the system has fully specified
constraints. When resolving supplies for regulators we do not have the
equivalent code and instead just directly use the regulator_dev_lookup()
result causing spurious failures.
This does not affect DT systems since we are able to detect missing
mappings directly as part of regulator_dev_lookup() and so have appropriate
handling in the DT specific code.
Reported-by: Christian Hartmann <cornogle@googlemail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add lockdep_assert_held_once() to functions explicitly mentioning that
rdev or regulator_list mutex must be held. Using WARN_ONCE shouldn't
pollute the dmesg to much.
The patch (if CONFIG_LOCKDEP enabled) will show warnings in certain
regulators calling regulator_notifier_call_chain() without rdev->mutex
held.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators can limit their input current (typically annotated
as ilim). Add an op (set_input_current_limit) and a DT property +
constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators support a "soft start" feature where the voltage
ramps up slowly when the regulator is enabled. Add an op
(set_soft_start) and a DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some regulators have a fixed load that isn't captured by
consumers that the kernel knows about. Add a constraint to
support this.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to avoid potential overflows in print_constraints we
better replace sprintf() with scnprintf().
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
We weren't taking into account the already used buffer when telling
sprintf() where to print to.
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't consider a failure to add the sysfs node as a problem,
so use sysfs_create_link_nowarn() so that we don't print a
backtrace when duplicated files exist. Also, downgrade the printk
message to a debug statement so that we're quiet here. This
allows multiple drivers to request a CPU's regulator so that
CPUfreq and AVSish drivers can coexist.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Voltage regulators can have (unregulated) current limits too, so we should
probably output both voltage and current for all regulators.
Holding the rdev->mutex actually conflicts with _regulator_get_current_limit
but also is not really necessary, as the global regulator_list_mutex already
protects us from the regulator vanishing while we go through the list.
On the rk3288-firefly the summary now looks like:
regulator use open bypass voltage current min max
-------------------------------------------------------------------------------
vcc_sys 0 12 0 5000mV 0mA 5000mV 5000mV
vcc_lan 1 1 0 3300mV 0mA 3300mV 3300mV
ff290000.ethernet 0mV 0mV
vcca_33 0 0 0 3300mV 0mA 3300mV 3300mV
vcca_18 0 0 0 1800mV 0mA 1800mV 1800mV
vdd10_lcd 0 0 0 1000mV 0mA 1000mV 1000mV
[...]
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On modern systems the regulator hierarchy can get quite long and nested
with regulators supplying other regulators. In some cases when debugging
it might be nice to get a tree of these regulators, their consumers
and the regulation constraints in one go.
To achieve this add a regulator_summary sysfs node, similar to
clk_summary in the common clock framework, that walks the regulator
list and creates a tree out of the regulators, their consumers and
core per-regulator settings.
On a rk3288-firefly the regulator_summary would for example look
something like:
regulator use open bypass value min max
-----------------------------------------------------------------------
vcc_sys 0 12 0 5000mV 5000mV 5000mV
vcc_lan 1 1 0 3300mV 3300mV 3300mV
ff290000.ethernet 0mV 0mV
vcca_33 0 0 0 3300mV 3300mV 3300mV
vcca_18 0 0 0 1800mV 1800mV 1800mV
vdd10_lcd 0 0 0 1000mV 1000mV 1000mV
vccio_sd 0 0 0 3300mV 3300mV 3300mV
vcc_20 0 3 0 2000mV 2000mV 2000mV
vcc18_lcd 0 0 0 1800mV 1800mV 1800mV
vcc_18 0 2 0 1800mV 1800mV 1800mV
ff100000.saradc 0mV 0mV
ff0d0000.dwmmc 1650mV 1950mV
vdd_10 0 0 0 1000mV 1000mV 1000mV
vdd_log 0 0 0 1100mV 1100mV 1100mV
vcc_io 0 3 0 3300mV 3300mV 3300mV
ff0f0000.dwmmc 3300mV 3400mV
vcc_flash 1 1 0 1800mV 1800mV 1800mV
ff0f0000.dwmmc 1700mV 1950mV
vcc_sd 1 1 0 3300mV 3300mV 3300mV
ff0c0000.dwmmc 3300mV 3400mV
vcc_ddr 0 0 0 1200mV 1200mV 1200mV
vdd_gpu 0 0 0 1000mV 850mV 1350mV
vdd_cpu 0 1 0 900mV 850mV 1350mV
cpu0 900mV 900mV
vcc_5v 0 2 0 5000mV 5000mV 5000mV
vcc_otg_5v 0 0 0 5000mV 5000mV 5000mV
vcc_host_5v 0 0 0 5000mV 5000mV 5000mV
regulator-dummy 0 0 0 0mV 0mV 0mV
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of resolving regulator supplies during registration move this to
the time of a consumer retrieving a handle. The benefit is that it's
possible for one driver to register regulators with internal
dependencies out of order.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If multiple regulator devices of the same type exist in a system,
the regulator driver assigns generic names for the regulators it
provides, and debugfs is enabled, the regulator subsystem attempts
to create multiple entries with the same name in the regulator debugfs
directory. This fails for all but the first regulator, resulting in
multiple "Failed to create debugfs directory" log entries.
To avoid the problem, prepend the debugfs directory name for a regulator
with its parent device name if available, but only if no explicit
regulator name was provided.
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the regulator_set_optimum_mode() function regulator_set_load() to
better represent what's going on.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Normally _regulator_do_enable() isn't called on an already-enabled
rdev. That's because the main caller, _regulator_enable() always
calls _regulator_is_enabled() and only calls _regulator_do_enable() if
the rdev was not already enabled.
However, there is one caller of _regulator_do_enable() that doesn't
check: regulator_suspend_finish(). While we might want to make
regulator_suspend_finish() behave more like _regulator_enable(), it's
probably also a good idea to make _regulator_do_enable() robust if it
is called on an already enabled rdev.
At the moment, _regulator_do_enable() is _not_ robust for already
enabled rdevs if we're using an ena_pin. Each time
_regulator_do_enable() is called for an rdev using an ena_pin the
reference count of the ena_pin is incremented even if the rdev was
already enabled. This is not as intended because the ena_pin is for
something else: for keeping track of how many active rdevs there are
sharing the same ena_pin.
Here's how the reference counting works here:
* Each time _regulator_enable() is called we increment
rdev->use_count, so _regulator_enable() calls need to be balanced
with _regulator_disable() calls.
* There is no explicit reference counting in _regulator_do_enable()
which is normally just a warapper around rdev->desc->ops->enable()
with code for supporting delays. It's not expected that the
"ops->enable()" call do reference counting.
* Since regulator_ena_gpio_ctrl() does have reference counting
(handling the sharing of the pin amongst multiple rdevs), we
shouldn't call it if the current rdev is already enabled.
Note that as part of this we cleanup (remove) the initting of
ena_gpio_state in regulator_register(). In _regulator_do_enable(),
_regulator_do_disable() and _regulator_is_enabled() is is clear that
ena_gpio_state should be the state of whether this particular rdev has
requested the GPIO be enabled. regulator_register() was initting it
as the actual state of the pin.
Fixes: 967cfb18c0 ("regulator: core: manage enable GPIO list")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The _regulator_do_enable() call ought to be a no-op when called on an
already-enabled regulator. However, as an optimization
_regulator_enable() doesn't call _regulator_do_enable() on an already
enabled regulator. That means we never test the case of calling
_regulator_do_enable() during normal usage and there may be hidden
bugs or warnings. We have seen warnings issued by the tps65090 driver
and bugs when using the GPIO enable pin.
Let's match the same optimization that _regulator_enable() in
regulator_suspend_finish(). That may speed up suspend/resume and also
avoids exposing hidden bugs.
[Use much clearer commit message from Doug Anderson]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The commit [39f802d6b6d9: 'regulator: Build sysfs entries with static
attribute groups'] converted the sysfs entry creation to static
attribute groups, but this resulted in a regression due to the NULL
check of rdev->constraints. At the point where the device is
registered, rdev->constraints isn't set, so the attributes depending
on it are missing.
We may fix it by shuffling the code order in regulator_register(), but
a quicker fix is to just remove this NULL check. rdev->constraints is
in anyway always set to non-NULL in set_machine_constraints(), thus
the check there is basically superfluous.
Fixes: 39f802d6b6 ('regulator: Build sysfs entries with static attribute groups')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reportded-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose the requested load directly to the regulator implementation for
hardware that does not support the normal enum based set_mode().
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling device_create_file() manually after the device
registration, put all in attribute groups and filter the unwanted ones
via is_visible callback. This not only simplifies the code but also
avoids the possible race between the device registration and sysfs
registration.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor drms_uA_update() slightly to allow regulator_set_optimum_mode()
to utilize the same logic instead of duplicating it.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Update documentation for regulator_register() function after renaming
its argument.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When drivers use simplified DT parsing method (they provide
'regulator_desc.of_match') they still may want to parse custom
properties for some of the regulators. For example some of the
regulators support GPIO enable control.
Add a driver-supplied callback for such case. This way the regulator
core parses common bindings offloading a lot of code from drivers and
still custom properties may be used.
The callback, called for each parsed regulator, may modify the
'regulator_config' initially passed to regulator_register().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Copy the 'regulator_config' structure passed to regulator_register()
function so the driver could safely modify it after parsing init data.
The driver may want to change the config as a result of specific init
data parsed by regulator core (e.g. when core handled parsing device
tree).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator framework maintains a list of consumer regulators
for a regulator device and protects it from concurrent access using
the regulator device's mutex lock.
In the case of regulator_put() the consumer is removed and regulator
device's parameters are updated without holding the regulator device's
mutex. This would lead to a race condition between the regulator_put()
and any function which traverses the consumer list or modifies regulator
device's parameters.
Fix this race condition by holding the regulator device's mutex in case
of regulator_put.
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch initializes regulator_no to -1 to avoid extra subtraction
operation performed every time we register a regulator and avoid negative
regulator no in its name.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After freeing pin from regulator_ena_gpio_free, loop can access
the pin. So this patch fixes not to access pin after freeing.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a PRE_DISABLE notification so that consumers can use a
notifier to run any steps required to prepare for the
regulator being switched off. Since the regulator disable
can fail an abort notification is also added.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some systems have very large numbers of regulators so the constraint
logging done at startup can end up being a very big part of the boot
output which is both verbose and slows things down if the console is
a serial console. Lower to dev_dbg() instead, we may want to provide
a boot parameter to raise this in future but for now people can edit
the source.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Most drivers do not set the ena_gpio field of struct regulator_config
before passing it to the regulator core. This is fine as long as the
gpio identifier that is passed is a positive integer. But the gpio
identifier 0 is also valid. So we are not able to decide wether we got a
real gpio identifier or not based on a 0 in ena_gpio.
To be able to decide if it is a valid gpio that got passed, this patch
adds a ena_gpio_initialized field that should be set if was initialized
with a correct value, either a gpio >= 0 or a negative error number. The
core then checks if ena_gpio or ena_gpio_initialized before handling it
as a gpio. This way we maintain backwards compatibility and fix the
behaviour for gpio number 0.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regulator drivers which support DT all repeat very similar code
to supply a list of known regulator identifiers to be matched with DT,
convert that to platform data which is then matched up with the regulators
as they are registered. This is both fiddly to get right and for devices
which can use the standard helpers to provide their operations is the main
source of code in the driver.
Since this code is essentially identical for most drivers we can factor it
out into the core, moving the identifiers in the match table into the
regulator descriptors and also allowing drivers to pass in the name of the
subnode to search. When a driver provides an of_match string for the
regulator the core will attempt to use that to obtain init_data, allowing
the driver to remove all explicit code for DT parsing and simply provide
data instead.
The current code leaks the phandles for the child nodes, this will be
addressed incrementally and makes no practical difference for FDT anyway
as the DT data structures are never freed.
Signed-off-by: Mark Brown <broonie@linaro.org>
In some cases we need to know when a regulator is about to be changed.
Add a way for clients to be notified. Note that for set_voltage() we
don't necessarily know what voltage we'll end up with, so we tell the
client what the range will be so they can prepare.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie+linaro@kernel.org>
Commit 272e2315fa ("regulator: core: add const qualifier to ops in
struct regulator_desc") introduced const qualifier to ops in regulator_desc.
This patch adds 'const' to regulator_ops vars in newly added core APIs
for v3.17-rc1:
- regulator_get_hardware_vsel_register()
- regulator_list_hardware_vsel()
This patch also fix a build error in mc13892-regulator.c due to const
regulator_desc.ops. Modification of regulator_desc.ops' member fields is not
allowed.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some regulator require a minimum delay between its disable and next enable.
This is to avoid damages when out-of-range frequent disable/enable of a
single regulator can bring to the regulator chip.
Add @off_on_delay to struct regulator_desc. Device drivers' can use this field
to set this guard time.
Add @last_off_jiffy to struct regulator_dev. When @off_on_delay is set by
driver, regulator core can store its last off (disable) time into this field.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
A common delay function can be helpful when implementing new features. Factor
it out to maximize code reusability.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
struct regulator_ops *ops is a member in struct regulator_desc, which gets
its value from individual regulator driver upon regulator_register() and
is used by regulator core APIs. It's not allowed for regulator core to
modify any of these callbacks in *ops. Add 'const' qualifier to enforce that.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Load switches are modeled as regulators but they just provide
the voltage of their parent input supply. So, the drivers for
these switches usually neither provide a .list_voltage handler
not set a .n_voltages count. But there is code in the kernel
that assumes that all regulators should be able to provide this
information (e.g: cpufreq and mmc subsystems).
If the voltage count and list are not available for a regulator
and it has a parent input supply, then use the parent values.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Load switches are modeled as regulators but they just provide
the voltage of their parent input supply. So the drivers for
these switches usually don't provide a .get_voltage function
handler but there is code in the kernel that assumes that all
regulators should be able to provide its current voltage rail.
So, if the output voltage for a regulator is not available and
it has a parent supply, then pass the voltage of its parent.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add helper functions that allow regulator consumers to obtain low-level
details about the regulator hardware, like the voltage selector register
address and such. These details can be useful when configuring hardware
or firmware that want to do low-level access to regulators, with no
involvement from the kernel.
The use-case for Tegra is a voltage-controlled oscillator clocksource
which has control logic to change the supply voltage via I2C to achieve
a desired output clock rate.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert the regulator GPIO handling to use a gpio descriptor rather than
numbers. This allows us to revise the interfaces to permit all GPIOs
to be used with the regulator core.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
With commit 064d5cd110
(regulator: core: Fix the init of DT defined fixed regulators)
We ensure that regulator must be capable of providing it's current
voltage when constraints are used, however adding the return value in
the print is a little more informative to explain the nature of the
failure involved.
So, instead of providing message such as:
smps9: failed to get the current voltage
having error value added to the message such as:
smps9: failed to get the current voltage(-22)
is a little more informative for debugging the error.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a regulator is defined using DT and it has a single voltage the
regulator init always tries to apply this voltage. However it fails if
the regulator isn't settable because it is using an internal low level
function. To overcome this we now first query the regulator and only
set it if needed.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_init_complete does a scan of regulators which dont have
always-on or consumers are automatically disabled as being unused.
However, with deferred probing, late_initcall() is too soon to
declare a regulator as unused as the regulator itself might not
have registered due to defferal - Example: A regulator deffered due
to i2bus not available which in turn is deffered due to pinctrl
availability.
Since deferred probing is done in late_initcall(), do the cleanup of
unused regulators by regulator_init_complete in late_initcall_sync
instead of late_initcall.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
[nm@ti.com: minor rewording]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the spirit of conservatism that governs our general approach to
permissions it is better if we don't touch regulators we weren't explicitly
given permissions to control. This avoids the need to explicitly specify
unknown regulators in DT as always on, if a regulator is not otherwise
involved in software control it can be omitted from the DT.
Regulators explicitly given constraints in DT still need to have an always
on constraint specified as before.
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_get_optional() doesn't hold an exclusive reference to
the regulator. Fix the documentation and reword the exclusive
documentation to fix the grammatical error "this reference is
held".
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use map_voltage_linear_range() if list_voltage_linear_range() is in use and
nothing is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the regulator core does not take an additional reference to
the of_node it is passed. This means that the caller must ensure that
the of_node is valid for the duration of the regulator's existance.
It is reasonable for the framework to assume it is passed a valid
of_node but seems onerous for it to assume the caller will keep the node
valid for the life-time of the regulator, especially when
devm_regulator_register is used and there will likely be no code in the
driver called at the point it would be safe to put the of_node.
This patch adds an additional of_node_get when the regulator is
registered and an of_node_put when it is unregistered in the core. This
means individual drivers are free to put their of_node references at the
end of probe letting the regulator core handling it from there. This
simplifies code on the driver side.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A couple of fixes here which ensure that regulators using the core
support for GPIO enables work in all cases by ensuring that helpers are
used consistently rather than open coding in places and hence not having
GPIO support in some of them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vx3C
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes here which ensure that regulators using the core
support for GPIO enables work in all cases by ensuring that helpers
are used consistently rather than open coding in places and hence not
having GPIO support in some of them"
* tag 'regulator-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Replace direct ops->disable usage
regulator: core: Replace direct ops->enable usage
There are many places where ops->disable is called directly. Instead we
should use _regulator_do_disable() which also handles gpio regulators.
To be able to use the wrapper function from _regulator_force_disable(),
I moved the _notifier_call_chain() call from _regulator_do_disable() to
_regulator_disable(). This way, _regulator_force_disable() can use
different flags for _notifier_call_chain() without calling it twice.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are some direct ops->enable in the regulator core driver. This is
a potential issue as the function _regulator_do_enable() handles gpio
regulators and the normal ops->enable calls. These gpio regulators are
simply ignored when ops->enable is called directly.
One possible bug is that boot-on and always-on gpio regulators are not
enabled on registration.
This patch replaces all ops->enable calls by _regulator_do_enable.
[Handle missing enable operations -- broonie]
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator: Handle invalid enable operation for always/boot on regulators
Signed-off-by: Mark Brown <broonie@linaro.org>
Change "dummy supplies not allowed" error message to warning instead, as this
is a just warning message with no change to the behavior.
[Added a CC to stable since some other bug fixes cause this to come up
more frequently on PCs which is how it was noticed -- broonie]
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make it okay to call regulator_set_voltage on regulators with fixed
voltage if the requested range overlaps the current/configured voltage.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Once we have full constraints then all supply mappings should be known to
the regulator API. This means that we should treat failed lookups as fatal
rather than deferring in the hope of further registrations but this was
broken by commit 9b92da1f12 "regulator: core: Fix default return
value for _get()" which was targeted at DT systems but unintentionally
broke non-DT systems by changing the default return value.
Fix this by explicitly returning -EPROBE_DEFER from the DT lookup if we
find a property but no corresponding regulator and by having the non-DT
case default to -ENODEV when we have full constraints.
Fixes: 9b92da1f12 "regulator: core: Fix default return value for _get()"
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Fix the following checkpatch errors and warnings.
ERROR: trailing whitespace
ERROR: return is not a function, parentheses are not required
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Only print an error when _regulator_get() is expected to return a valid
regulator, that is when _regulator_get() is called from regulator_get() and
we're not using the dummy because we don't have full-constraints, or when
_regulator_get() is called from regulator_get_exclusive() in which case
returning a dummy is not allowed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Eliminate the gap between DT becoming available and this being used to say
we have full constraints by checking directly for DT every time we check
for full constraints. This improves interoperaton with optional regulator
support.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Simple code reorganisation so we can change the logic for deciding what
full constraints are more easily.
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit c368e5fc2a "regulator: fixed:
get rid of {get|list}_voltage()" broke regulator_list_voltage() for
the fixed regulator, because an earlier commit
5a523605af "regulator: core: provide
fixed voltage in desc for single voltage rail" missed to add support
for the fixed-voltage special case to that function. This patch
fixes that regression.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These patches add the ability to create an alternative device on which
a lookup for a certain supply should be conducted.
A common use-case for this would be devices that are logically
represented as a collection of drivers within Linux but are are
presented as a single device from device tree. It this case it is
necessary for each sub device to locate their supply data on the main
device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps people spot if they have missed a supply from a device tree or
equivalent data structure.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Keep busy-wait looping to a minimum while waiting for a regulator to
ramp-up to the target voltage. This follows the guidelines set forth
in Documentation/timers/timers-howto.txt and assumes that regulators
are never enabled in atomic context.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure that the return value is always set when we return now that the
logic has changed for regulator_get_optional() so we don't get missing
codes leaking out.
Reported-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that we are defaulting to providing dummy regulators fix the logic
for substituting a dummy by making the default return code -EPROBE_DEFER.
Reported-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Machine constraints is configured during regulator register. If current
constraints are provided through machine constraints then it is observed
that sometime the current configured on rail is out of range what machine
constraint has.
Set the current constraints when setting machine constraints to make
sure that rail's current is within the range of given machine constraints.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The turn-on time of the regulator depends on the regulator device's
electrical characteristics. Sometimes regulator turn-on time also
depends on the capacitive load on the given platform and it can be
more than the datasheet value.
The driver provides the enable-time as per datasheet.
Add support for configure the enable ramp time through regulator
constraints so that regulator core can take this value for enable
time for that regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No boards have used this functionality and the new default of providing
dummy regulators by default provides a better solution to the problem it
was trying to solve.
Signed-off-by: Mark Brown <broonie@linaro.org>
When a system has said that it has fully specified constraints for its
regulators it is still possible that some supplies may be missing,
especially if regulator support has been added to a driver after the
board was integrated. We can handle such situations more gracefully by
providing a dummy regulator.
Unless the caller has specifically indicated that the system design may
not include a given regulator by using regulator_get_optional() or that
it needs its interactions to have an effect using regulator_get_exclusive()
provide a dummy regulator if we can't locate a real one.
The kconfig option REGULATOR_DUMMY that provided similar behaviour for all
regulators has been removed, systems that need it should flag that they
have full constraints instead.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cut down on the size of core.c a bit more and ensure that the devres
versions of things don't do too much peering inside the internals of
the APIs they wrap.
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation of devm_regulator_get, devm_regulator_get_exclusive and
devm_regulator_get_optional are almost the same.
Introduce _devm_regulator_get helper function and refactor the code.
Also move devm_regulator_get_exclusive to proper place, put it after
regulator_get_exclusive() function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulator drivers have a remove function that consists solely of
calling regulator_unregister() so provide a devm_regulator_register()
in order to allow this repeated code to be removed and help eliminate
error handling code.
Signed-off-by: Mark Brown <broonie@linaro.org>
If given rail has the single voltage (n_voltages = 1) then provide the
rail voltage through regulator descriptor so that core can use this
value for finding voltage.
This will avoid the implementation of the callback for get_voltage() or
list_voltage() callback on regulator driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a resource managed regulator_get_exclusive()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move regulator_list_voltage_{linear,linear_range,table} helper functions to
helpers.c.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While the majority of supplies on devices are mandatory and can't be
physically omitted for electrical reasons some devices do have optional
supplies and need to know if they are missing, MMC being the most common
of these.
Currently the core accurately reports all errors when regulators are
requested since it does not know if the supply is one that must be provided
even if by a regulator software does not know about or if it is one that
may genuinely be disconnected. In order to allow this behaviour to be
changed and stub regulators to be provided in the former case add a new
regulator request function regulator_get_optional() which provides a hint
to the core that the regulator may genuinely not be connected.
Currently the implementation is identical to the current behaviour, future
patches will add support in the core for returning stub regulators in the
case where normal regulator_get() fails and the board has requested it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the regulator class code to use
the correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code does not allow fixed voltage range in multiple linear ranges.
If someone does set range->uV_step == 0 in one of the linear ranges, we hit
divided by zero bug. This patch fixes this issue.
For fixed voltage range, return any selector means the same voltage.
Thus just return 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to use a normal per-CPU workqueue for delayed power downs
as they're not timing or performance critical and waking up a core for them
would defeat some of the point.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
In function _regulator_do_set_voltage(), old_selector gets intialised only
if (_regulator_is_enabled(rdev) && rdev->desc->ops->set_voltage_time_sel &&
rdev->desc->ops->get_voltage_sel)) is true.
Before calling set_voltage_time_sel() we checks if (old_selector >= 0) and it
will true if it got intialised properly. so we don't need to check again
_regulator_is_enabled(rdev) && rdev->desc->ops->set_voltage_time_sel before
calling set_voltage_time_sel().
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some hardwares support disabling ramp delay, so adding ramp_disable flag to
constraints. It will be used to figure out whether ramp_delay in constraints
is explicitly set to zero or its unintialized (zero by default).
And we don't need to call set_voltage_time_sel() for regulators for whom ramp
delay is disabled in constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulators have several linear ranges of selector with different
step sizes, for example offering better resolution at lower voltages.
Provide regulator_{map,list}_voltage_linear_range() allowing these
regulators to use generic code. To do so a table of regulator_linear_range
structs needs to be pointed to from the descriptor.
This was inspired by similar code included in a driver submission from
Chao Xie and Yi Zhang at Marvell.
Signed-off-by: Mark Brown <broonie@linaro.org>
Add regulator_get_linear_step(), which returns the voltage step size
between VSEL values for linear regulators. This is intended for use
by regulator consumers which build their own voltage-to-VSEL tables.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a couple kernel-doc lines to get rid of kernel-doc generation
warnings, no functional change.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of regulator hardware has ascendant voltage list.
This patch adds regulator_map_voltage_ascend() and export it.
Drivers that have ascendant voltage list can use this as their map_voltage()
operation, this is more efficient than default regulator_map_voltage_iterate()
function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 6d191a5fc7
(regulator: core: Don't defer probe if there's no DT binding for a supply)
Attempted to differentiate between regulator_get() with an actual
DT binding for the supply and when there is none to avoid unnecessary
deferal.
However, ret value supplied by regulator_dev_lookup() is being
ignored by regulator_get(). So, exit with the appropriate return value.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Regulator drivers may specify regulator_desc->supply_name which
regulator_register() will use to find the supply node for a regulator.
If no supply was specified in the device tree or the supply has yet
to be registered regulator_register() will fail, deferring the probe
of the regulator. In the case where no supply node was specified in the
device tree, there is no supply and it is pointless to try and find one
later, so go ahead and add the regulator without the supply.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add enable_is_inverted flag to indicate set enable_mask bits to disable
when using regulator_enable_regmap and friends APIs.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulator_dev has regulator_enable_gpio structure.
'ena_gpio' and 'ena_gpio_invert' were moved to in regulator_enable_gpio.
regulator_dev ---> regulator_enable_gpio
.ena_gpio .gpio
.ena_gpio_invert .ena_gpio_invert
Pointer, 'ena_pin' is used for checking valid enable GPIO pin.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To support shared enable GPIO pin, replace GPIO code with new static functions
Reference count: 'enable_count'
Balance the reference count of each GPIO and actual pin control.
The count is incremented with enabling GPIO.
On the other hand, it is decremented on disabling GPIO.
Actual GPIO pin is enabled at the initial use.(enable_count = 0)
The pin is disabled if it is not used(shared) any more. (enable_count <=1)
Regardless of the enable count, update GPIO state of the regulator.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A Regulator can be enabled by external GPIO pin.
This is configurable in the regulator_config.
At this moment, the GPIO can be owned by only one regulator device.
In some devices, multiple regulators are enabled by shared one GPIO pin.
This patch extends this limitation, enabling shared enable GPIO of regulators.
New list for enable GPIO: 'regulator_ena_gpio_list'
This manages enable GPIO list.
New structure for supporting shared enable GPIO: 'regulator_enable_gpio'
The enable count is used for balancing GPIO control count.
This count is incremented when GPIO is enabled.
On the other hand, it's decremented when GPIO is disabled.
Reference count: 'request_count'
The reference count, 'request_count' is incremented/decremented on
requesting/freeing the GPIO. This count makes sure only free the GPIO
when it has no users.
How it works
If the GPIO is already used, skip requesting new GPIO usage.
The GPIO is new one, request GPIO function and add it to the list of
enable GPIO.
This list is used for balancing enable GPIO count and pin control.
Updating a GPIO and invert code moved
'ena_gpio' and 'ena_gpio_invert' of the regulator_config were moved to
new function, regulator_ena_gpio_request().
Use regulator_enable_pin structure rather than regulator_dev.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unwinding code disables all successfully enabled regulators.
Error is logged for every failed regulator.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit f59c8f9f (regulator: core: Support bypass mode)
has a short documentation error around the regulator_allow_bypass
parameter 'enable' which is documented as 'allow'.
This generates kernel-doc warning as follows:
./scripts/kernel-doc drivers/regulator/core.c >/dev/null
Warning(drivers/regulator/core.c:2841): No description found for parameter 'enable'
Warning(drivers/regulator/core.c:2841): Excess function parameter 'allow' description in 'regulator_allow_bypass'
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit dd8004af: 'regulator: core: Log when a device causes a voltage
constraint fail', tried to print out some information about the
check consumer min/max uV fixup, however, it uses a garbage pointer
left over from list_for_each_entry leading to boot messages in the
form:
'[ 2.079890] <RANDOM ASCII>: Restricting voltage, 3735899821-4294967295uV'
Because it references regulator->dev, it could potentially read memory from
anywhere causing a panic.
This patch instead uses rdev and the updated min/max uV values.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Optimize _regulator_do_set_voltage() for the case selector is equal to
old_selector. Since the voltage does not change, we don't need to call
set_voltage_sel() and set_voltage_time_sel() in this case.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_register() does not return 0 on success, fix the comment.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some DVM regulators needs to update apply_bit after setting vsel_reg to
initiate voltage change on the output. This patch adds apply_reg and
apply_bit to struct regulator_desc and update
regulator_set_voltage_sel_regmap() to set apply_bit of apply_reg when
apply_bit is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Regulator drivers with continuous_voltage_range flag set allows not setting
n_voltages. Thus if continuous_voltage_range is set, check the constraint range
instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Having a linear_min_sel setting means the first linear_min_sel selectors are
invalid. We need to subtract linear_min_sel when use n_voltages to determinate
if regulator can change voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a regulator_can_change_voltage() function for the subsytems or
drivers which might check if applying voltage change is possible and use
special workaround code when the driver is used with fixed regulators or
regulators with disabled ability to change the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some drivers (at least 3 drivers) have such variant of linear mapping that
the first few selectors are invalid and the reset are linear mapping.
Let's support this case in core.
This patch adds linear_min_sel in struct regulator_desc,
so we can allow specific minimal selector for starting linear mapping.
Then extends regulator_[map|list]_voltage_linear() to support this feature.
Note that for selectors less than min_linear_index, we need count them to
n_voltages so regulator_list_voltage() won't fail while checking the boundary
for selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.
This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the gpio_request_one() fails, or returns EPROBE_DEFER, the
regulator must be device_unregister()ed. When this is not done,
there are WARNING: from sysfs:
WARNING: at fs/sysfs/file.c:343 sysfs_open_file+0x238/0x268()
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some regulators can set any voltage within the constraints range,
not being limited to specified operating points.
This patch makes it possible to describe such regulator and makes
the regulator_is_supported_voltage() function behave correctly.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
Many regulators support a bypass mode where they simply switch their
input supply to the output. This is mainly used in low power retention
states where power consumption is extremely low so higher voltage or
less clean supplies can be used.
Support this by providing ops for the drivers and a consumer API which
allows the device to be put into bypass mode if all consumers enable it
and the machine enables permission for this.
This is not supported as a mode since the existing modes are rarely used
due to fuzzy definition and mostly redundant with modern hardware which is
able to respond promptly to load changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Graeme Gregory <gg@slimlogic.co.uk>
If the device doesn't have a regmap specified by the driver and we can't
find one on the device itself try its parent, providing a useful defualt
for many MFDs.
[Rewrite commit message -- broonie]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Users (especially framework code) may end up passing in a zero deferral
time depending on runtime conditions or configuration. If they do then
just call regulator_disable() directly to save scheduling.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If a regulator only supports a single voltage list_voltage() can be used
to report what that voltage is so add this as one of the criteria for
creating the microvolts file in sysfs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix regulator kernel-doc warnings:
Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
Fix regulator kernel-doc warnings:
Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 65f735082d ("regulator: core: Add core support for GPIO controlled
enable lines") introduced enable gpio entry in regulator configuration
structure. Some drivers use '-1' as a placeholder for marking that such
gpio line is not available, because '0' is considered as a valid gpio
number. This patch fixes initialization of such drivers (like MAX8952
on UniversalC210 board), when '-1' is provided as enable gpio pin in the
regulator's platform data.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the regulator doesn't supply a way of reading back the voltage but does
provide a list_voltage() operation then use that with a selector of zero
to read the voltage. Regulators doing this means that we have the list
operation there for consumers that want to configure themselves.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This prevents the output of just
dummy:
in the boot log. Now it says:
regulator-dummy: no parameters
which at least doesn't make it look like an accidental printk and also doesn't
only use "dummy" which could mean anything.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is to address the following warning during compilation time: (Compile on x86_64)
CC drivers/regulator/core.o
drivers/regulator/core.c: In function '_regulator_do_set_voltage':
drivers/regulator/core.c:2183:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
This patch adds a temporary variable to avoid double cast.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown