Make use of the hybrid tuner framework so the analog and digital parts of the
au8522 demodulator can make use of the same shared state.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the au8522 is idle, put the chip into a low power mode (reduces power
consumption from 450ma to 346ma)
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the i2c messages to read and write registers, the two high order bits
of the first byte dictates whether it is a read or a write operation.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the au8522 state structure, as well as exposing functions needed by the
analog side of the demodulator into a common header file.
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename the au8522.c file to au8522_dig.c so that more source files can be
added to the driver while preserving the original name of au8522.ko
Thanks to Michael Krufky <mkrufky@linuxtv.org> and Steven Toth
<stoth@linuxtv.org> for providing sample hardware, engineering level support,
and testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It appears TS discontinuity about one per 10 hrs if CAM used.
Patch to fix it.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Setting state->frontend.demodulator_priv to NULL in the event of
a kzalloc error will result in an OOPS. Just remove that line.
Thanks to Matthias Schwarzott for pointing this out.
Cc: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We'll start off with MODULE_VERSION("0.1")
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
small whitespace cleanup - space missing after the *
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function prototype is defined but the function itself does not exist.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix dvb frontend debug variable to be static, to avoid linker
errors:
drivers/built-in.o:(.data+0xf4b0): multiple definition of `debug'
arch/x86/kernel/built-in.o:(.kprobes.text+0x90): first defined here
ld: Warning: size of symbol `debug' changed from 85 in arch/x86/kernel/built-in.o to 4 in drivers/built-in.o
It would also be Good if arch/x86/kernel/entry_32.S didn't have a
non-static 'debug' symbol. OTOH, it helps catch things like this one.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of asking a lot of questions for the poor users, let's just hide
the frontend customise menu, if the user doesn't want to customise.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is based on initial work by Tino Reichardt and was heavily changed.
The datasheet of the zl10036 can be found here and on other places on the net:
http://www.mcmilk.de/projects/dvb-card/datasheets/ZL10036.pdf
The zl10038 is similar to the zl10036, so it is maybe possible to write a common
driver of necessary.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was a typo in the function
name, it should be lnbh24_attach, and not lnbp24_attach.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add last piece of code to support ST STV0900 dual demodulator.
The IC consist of two dependent parts.
It may use single or dual mode.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The IC consist of two dependent parts.
It may use single or dual mode.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The controller consist of two independent parts.
Every part is similar to LNBP21, but has configurable i2c address.
It is used in NetUP Dual DVB-S2 CI card.
http://linuxtv.org/wiki/index.php/NetUP_Dual_DVB_S2_CI
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner is used in NetUP Dual DVB-S2 CI card.
http://linuxtv.org/wiki/index.php/NetUP_Dual_DVB_S2_CI
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
[mchehab@redhat.com: removed a wrong header: "cx23885.h"]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi there!
While having a look at the allocation of struct dvb_frontend in *_attach
functions, I found some cases calling memset after kzalloc. This is
redundant, and the attached patch removes these calls.
I also changed one case calling kmalloc and memset to kzalloc.
Regards
Matthias
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For i2c normal work, we need to slow down the bus speed. However, the
slow down breaks the eeprom firmware load. So, use normal speed for
eeprom booting and then restore the i2c speed after that.
It should also be noticed that no other I2C transfer should be in course
while booting from eeprom, otherwise, tda10046 goes into an instable
state. So, proper locking are needed at the i2c bus master.
Tested with saa7134 MSI TV @nyware A/D board, that comes with an eeprom
with firmware version 29.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some cards uses cx24116 LNB_DC pin for LNB power control,
some not uses, some uses it different way, like HVR-4000.
Tested-by : Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here is a patch which adds some documentation about meanings of the
the lnbp21 system register bits.
Signed-off-by: Hans Werner <hwerner4@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now there is a card, which uses cx24116 to control LNB DC voltage.
It is DVBWorld DVBS2 PCI-e 2005.
The patch is nedded to add support for that card.
1. Rename CMD_SET_TONEPRE to CMD_LNBDCLEVEL.
2. Fill set_voltage with actually control voltage code.
3. Correct set_tone to not affect voltage.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
in Hz not kHz, and a comment incorrectly says MHz instead of Hz. I
don't know if this caused real problems anywhere
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
zl10353 i2c-gate was always closed and due to that devices having tuner
behind i2c-gate were broken. Add module configuration which allows disabling
i2c-gate only when really needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just like with the s5h1411, the s5h1409 needs a soft-reset in order for it
to know that the tuner has been told to change frequencies. This change
changes the behavior from "random tuning times between 500ms to complete
tuning lock failures" to "tuning lock consistently within 700ms".
Thanks to Robert Krakora <rob.krakora@messagenetsystems.com> for doing
initial testing of the patch on the KWorld 330U.
Thanks to Andy Walls <awalls@radix.net> for doing testing of the patch on
the HVR-1600.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for doing additional testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
anysee.c:44:5: warning: symbol 'dvb_usb_anysee_delsys' was not declared. Should it be static?
cx24116.c:378:3: warning: symbol 'CX24116_MODFEC_MODES' was not declared. Should it be static?
stb0899_algo.c:57:5: warning: symbol 'stb0899_get_srate' was not declared. Should it be static?
stb0899_algo.c:766:6: warning: symbol 'Log2Int' was not declared. Should it be static?
stb0899_drv.c:137:20: warning: symbol 'stb0899_quant_tab' was not declared. Should it be static?
stb0899_drv.c:180:20: warning: symbol 'stb0899_est_tab' was not declared. Should it be static?
stb0899_drv.c:220:5: warning: symbol '_stb0899_read_reg' was not declared. Should it be static?
budget-ci.c:1348:23: warning: symbol 'tt3200_stb6100_config' was not declared. Should it be static?
/home/v4l/master/v4l/cx25840-core.c:190:6: warning: symbol 'cx25840_work_handler' was not declared. Should it be static?
/home/v4l/master/v4l/m5602_s5k83a.c:116:6: warning: symbol 's5k83a_dump_registers' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Report to userspace that cx24116 and stv0899 drivers support DVB-S2.
Signed-off by: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Acked-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix I2C bridge error in zl10353 if no tunner attached to internal I2C
bus of zl10353 chip.
When set enable bridge from internal I2C bus to the main I2C bus
(saa7134) the main I2C bus stopped very hardly. No any communication. In
our next board we solder additional resistors to internal I2C bus.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller