Add ethernet phy node in at91rm9200ek.dts.
The reg register is not specified, as it may differ depending on the init
process of the board:
ADDR0/1 phy pins are connected to PA13/14 rm9200 pins. Which means the phy
will take its address from these pins during the reset process.
The macb driver will launch a full scan on the mdio bus to discover the phy
address.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: changed to IRQ_TYPE_EDGE_BOTH as asked by Boris]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Swap names as they were improperly defined.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch removes the old main clk node which is now useless as sama5d3
SoCs and boards are no longer compatible with the old at91 clk
implementations.
It also remove old clock definitions (clock definitions using at91 old clk
framework).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch removes the selection of AT91_USE_OLD_CLK when selecting sama5d3
SoC support. This will enable automatically enable COMMON_CLK_AT91 option
and add support for at91 common clk implementation.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define the main clock frequency for the new main clock node
in sama5d3xcm.dtsi.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define sama5d3 clocks in sama5d3 device tree.
Add references to the appropriate clocks in each peripheral.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch encloses sama5d3 old clk registration in
"#if defined(CONFIG_OLD_CLK_AT91) #endif" sections.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch prepare the transition to common clk for sama5 dt boards by
replacing the timer init callback.
Clocks registration cannot be done in early init callback (as formerly done
by the old clk implementation) because it requires dynamic allocation
which is not ready yet during early init.
In the other hand, at91 clocks must be registered before
at91sam926x_pit_init is called because PIT (Periodic Interval Timer) driver
request the master clk (mck).
A new function (at91sama5_dt_timer_init) is created to fullfil these needs.
This function registers all at91 clks using the dt definition before
calling the PIT init function.
The device tree clock registration is enabled only if common clk is
selected. Else the old clk registration is been done during
at91_dt_initialize call.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new compatible string for PMC node to prepare the
transition to common clk.
These compatible string come from pmc driver in clk subsystem and are
needed to provide new device tree compatibility with old at91 clks
(device tree using common clks will use the new compatible strings).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use device tree to get the source clock of the PIT (Periodic Interval Timer).
If the clock is not found in device tree (or dt is not enabled) we'll try to
get it using clk_lookup definitions.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds at91 smd (Soft Modem) clock implementation using common clk
framework.
Not used by any driver right now.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds new at91 usb clock implementation using common clk framework.
This clock is used to clock usb ports (ohci, ehci and udc).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds new at91 utmi clock implementation using common clk framework.
This clock is a pll with a fixed factor (x40).
It is used as a source for usb clock.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds the following Kconfig options to prepare the transition to
common clk framework:
- AT91_USE_OLD_CLK: this option is selected by every SoC which does not
support new at91 clks based on common clk framework (SoC which does not
define the clock tree in its device tree).
This options is also selected when the user choose non dt boards support
(new at91 clks can only be registered from a device tree definition).
- COMMON_CLK_AT91: this option cannot be selected directly. Instead it is
enabled if these 3 conditions are met:
* at least one of the selected SoCs have a PMC (Power Management
Controller) Unit
* device tree support is enabled
* the old at91 clk implementation is disabled (every selected SoC define
its clks in its device tree and non dt boards support is disabled)
- OLD_CLK_AT91: this option cannot be selected directly. Instead it is
enabled if these 2 conditions are met:
* at least one of the selected SoCs have a PMC (Power Management
Controller) Unit
* at least one of the selected SoCs does not define its clks in its
device tree or non dt-boards support is enabled
This patch selects AT91_USE_OLD_CLK in all currently supported SoCs. These
selects will be removed after clk definitions are properly added in each
soc's device tree.
It also selects AT91_USE_OLD_CLK in all non-dt boards support.
AT91_PMC_UNIT references are replaced by OLD_CLK_AT91, because PMC Unit is
enabled for both old and common clk implementations, and old clk
implementation should not be compiled if COMMON_CLK is enabled.
To avoid future link errors, a new stub is created for at91_dt_clock_init
function if OLD_CLK_AT91 is disabled.
A new check is added in dt init functions (setup.c) to prepare for SoCs
supporting new clk implementation. These SoCs won't setup the
register_clocks callback (clk registration is done using of_clk_init).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch moves at91_pmc.h header from machine specific directory
(arch/arm/mach-at91/include/mach/at91_pmc.h) to clk include directory
(include/linux/clk/at91_pmc.h).
We need this to avoid reference to machine specific headers in clk
drivers.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull DRM fixes from Dave Airlie:
"I was going to leave this until post -rc1 but sysfs fixes broke
hotplug in userspace, so I had to fix it harder, otherwise a set of
pulls from intel, radeon and vmware,
The vmware/ttm changes are bit larger but since its early and they are
unlikely to break anything else I put them in, it lets vmware work
with dri3"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (36 commits)
drm/sysfs: fix hotplug regression since lifetime changes
drm/exynos: g2d: fix memory leak to userptr
drm/i915: Fix gen3 self-refresh watermarks
drm/ttm: Remove set_need_resched from the ttm fault handler
drm/ttm: Don't move non-existing data
drm/radeon: hook up backlight functions for CI and KV family.
drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
drm/i915: Do not enable package C8 on unsupported hardware
drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
drm/i915: encoder->get_config is no longer optional
drm/i915/tv: add ->get_config callback
drm/radeon/cik: Add macrotile mode array query
drm/radeon/cik: Return backend map information to userspace
drm/vmwgfx: Make vmwgfx dma buffers prime aware
drm/vmwgfx: Make surfaces prime-aware
drm/vmwgfx: Hook up the prime ioctls
drm/ttm: Add a minimal prime implementation for ttm base objects
drm/vmwgfx: Fix false lockdep warning
drm/ttm: Allow execbuf util reserves without ticket
drm/i915: restore the early forcewake cleanup
...
Pull ARM fixes from Russell King:
"Some small fixes for this merge window, most of them quite self
explanatory - the biggest thing here is a fix for the ARMv7 LPAE
suspend/resume support"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7894/1: kconfig: select GENERIC_CLOCKEVENTS if HAVE_ARM_ARCH_TIMER
ARM: 7893/1: bitops: only emit .arch_extension mp if CONFIG_SMP
ARM: 7892/1: Fix warning for V7M builds
ARM: 7888/1: seccomp: not compatible with ARM OABI
ARM: 7886/1: make OABI default to off
ARM: 7885/1: Save/Restore 64-bit TTBR registers on LPAE suspend/resume
ARM: 7884/1: mm: Fix ECC mem policy printk
ARM: 7883/1: fix mov to mvn conversion in case of 64 bit phys_addr_t and BE
ARM: 7882/1: mm: fix __phys_to_virt to work with 64 bit phys_addr_t in BE case
ARM: 7881/1: __fixup_smp read of SCU config should do byteswap in BE case
ARM: Fix nommu.c build warning
Pull third set of powerpc updates from Benjamin Herrenschmidt:
"This is a small collection of random bug fixes and a few improvements
of Oops output which I deemed valuable enough to include as well.
The fixes are essentially recent build breakage and regressions, and a
couple of older bugs such as the DTL log duplication, the EEH issue
with PCI_COMMAND_MASTER and the problem with small contexts passed to
get/set_context with VSX enabled"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/signals: Mark VSX not saved with small contexts
powerpc/pseries: Fix SMP=n build of rng.c
powerpc: Make cpu_to_chip_id() available when SMP=n
powerpc/vio: Fix a dma_mask issue of vio
powerpc: booke: Fix build failures
powerpc: ppc64 address space capped at 32TB, mmap randomisation disabled
powerpc: Only print PACATMSCRATCH in oops when TM is active
powerpc/pseries: Duplicate dtl entries sometimes sent to userspace
powerpc: Remove a few lines of oops output
powerpc: Print DAR and DSISR on machine check oopses
powerpc: Fix __get_user_pages_fast() irq handling
powerpc/eeh: More accurate log
powerpc/eeh: Enable PCI_COMMAND_MASTER for PCI bridges
There are two code paths how page with pmd page table can be freed:
pmd_free() and pmd_free_tlb().
I've missed the second one and didn't add page table destructor call
there. It leads to leak of page->ptl for pmd page tables, if
dynamically allocated page->ptl is in use.
The patch adds the missed destructor and modifies documentation
accordingly.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Andrey Vagin <avagin@openvz.org>
Tested-by: Andrey Vagin <avagin@openvz.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just a small pile of fixes for bugs and a few regressions. I'm still
trying to track down a driver load hang on my g33 (which infuriatingly
doesn't happen when loading the module manually after boot), somehow
bisecting loves to go astray on this one :( And there's a (harmless)
locking WARN in the suspend code due to one of Jesse's vlv backlight
rework patches. Otherwise nothing outstanding afaik.
* tag 'drm-intel-fixes-2013-11-20' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix gen3 self-refresh watermarks
drm/i915: Replicate BIOS eDP bpp clamping hack for hsw
drm/i915: Do not enable package C8 on unsupported hardware
drm/i915: Hold pc8 lock around toggling pc8.gpu_idle
drm/i915: encoder->get_config is no longer optional
drm/i915/tv: add ->get_config callback
drm/i915: restore the early forcewake cleanup
Partially revert "drm/i915: tune the RC6 threshold for stability"
drm/i915: flush cursors harder
i915: Use 120MHz LVDS SSC clock for gen5/gen6/gen7
x86/early quirk: use gen6 stolen detection for VLV
drm/i915/dp: set sink to power down mode on dp disable
The VSX MSR bit in the user context indicates if the context contains VSX
state. Currently we set this when the process has touched VSX at any stage.
Unfortunately, if the user has not provided enough space to save the VSX state,
we can't save it but we currently still set the MSR VSX bit.
This patch changes this to clear the MSR VSX bit when the user doesn't provide
enough space. This indicates that there is no valid VSX state in the user
context.
This is needed to support get/set/make/swapcontext for applications that use
VSX but only provide a small context. For example, getcontext in glibc
provides a smaller context since the VSX registers don't need to be saved over
the glibc function call. But since the program calling getcontext may have
used VSX, the kernel currently says the VSX state is valid when it's not. If
the returned context is then used in setcontext (ie. a small context without
VSX but with MSR VSX set), the kernel will refuse the context. This situation
has been reported by the glibc community.
Based on patch from Carlos O'Donell.
Tested-by: Haren Myneni <haren@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit a489043 "Implement arch_get_random_long() based on H_RANDOM" I
broke the SMP=n build. We were getting plpar_wrappers.h via spinlock.h
which breaks when SMP=n.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Up until now we have only used cpu_to_chip_id() in the topology code,
which is only used on SMP builds. However my recent commit a4da0d5
"Implement arch_get_random_long/int() for powernv" added a usage when
SMP=n, breaking the build.
Move cpu_to_chip_id() into prom.c so it is available for SMP=n builds.
We would move the extern to prom.h, but that breaks the include in
topology.h. Instead we leave it in smp.h, but move it out of the
CONFIG_SMP #ifdef. We also need to include asm/smp.h in rng.c, because
the linux version skips asm/smp.h on UP. What a mess.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
I encountered following issue:
[ 0.283035] ibmvscsi 30000015: couldn't initialize event pool
[ 5.688822] ibmvscsi: probe of 30000015 failed with error -1
which prevents the storage from being recognized, and the machine from
booting.
After some digging, it seems that it is caused by commit 4886c399da
as dma_mask pointer in viodev->dev is not set, so in
dma_set_mask_and_coherent(), dma_set_coherent_mask() is not called
because dma_set_mask(), which is dma_set_mask_pSeriesLP() returned EIO.
While before the commit, dma_set_coherent_mask() is always called.
I tried to replace dma_set_mask_and_coherent() with
dma_coerce_mask_and_coherent(), and the machine could boot again.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/platforms/wsp/wsp.c: In function ‘wsp_probe_devices’:
arch/powerpc/platforms/wsp/wsp.c:76:3: error: implicit declaration of function ‘of_address_to_resource’ [-Werror=implicit-function-declaration]
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit fba2369e6c (mm: use vm_unmapped_area() on powerpc architecture)
has a bug in slice_scan_available() where we compare an unsigned long
(high_slices) against a shifted int. As a result, comparisons against
the top 32 bits of high_slices (representing the top 32TB) always
returns 0 and the top of our mmap region is clamped at 32TB
This also breaks mmap randomisation since the randomised address is
always up near the top of the address space and it gets clamped down
to 32TB.
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If TM is not active there is no need to print PACATMSCRATCH
so we can save ourselves a line.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Machine check exceptions set DAR and DSISR, so print them in our
oops output.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
__get_user_pages_fast() may be called with interrupts disabled (see e.g.
get_futex_key() in kernel/futex.c) and therefore should use local_irq_save()
and local_irq_restore() instead of local_irq_disable()/enable().
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: <stable@vger.kernel.org> [v3.12]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This clarifies in the log whether the error is a global PHB error
or an individual PE being frozen.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On PHB3, we will fail to fetch IODA tables without PCI_COMMAND_MASTER
on PCI bridges. According to one experiment I had, the MSIx interrupts
didn't raise from the adapter without the bit applied to all upstream
PCI bridges including root port of the adapter. The patch forces to
have that bit enabled accordingly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc LE updates from Ben Herrenschmidt:
"With my previous pull request I mentioned some remaining Little Endian
patches, notably support for our new ABI, which I was sitting on
making sure it was all finalized.
The toolchain folks confirmed it now, the new ABI is stable and merged
with gcc, so we are all good. Oh and we actually missed the actual
Kconfig switch for LE so here it is, along with a couple more bug
fixes.
I have more fixes but not related to LE so I'll send them as a
separate pull request tomorrow, let's get this one out of the way.
Note that this supports running user space binaries using the new ABI,
but the kernel itself still needs to be built with the old one. We'll
bring fixes for that after -rc1.
Here's Anton log that goes with this series:
This patch series adds support for the new ABI, LPAR support for
H_SET_MODE and finally adds a kconfig option and defconfig.
ABIv2 support was recently committed to binutils and gcc, and should
be merged into glibc soon. There are a number of very nice
improvements including the removal of function descriptors. Rusty's
kernel patches allow binaries of either ABI to work, easing the
transition"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Wrong DWARF CFI in the kernel vdso for little-endian / ELFv2
powerpc: Add pseries_le_defconfig
powerpc: Add CONFIG_CPU_LITTLE_ENDIAN kernel config option.
powerpc: Don't use ELFv2 ABI to build the kernel
powerpc: ELF2 binaries signal handling
powerpc: ELF2 binaries launched directly.
powerpc: Set eflags correctly for ELF ABIv2 core dumps.
powerpc: Add TIF_ELF2ABI flag.
pseries: Add H_SET_MODE to change exception endianness
powerpc/pseries: Fix endian issues in pseries EEH code
The ARM architected timer driver doesn't compile without
GENERIC_CLOCKEVENTS selected, so ensure that we select it when building
for a platform that has the timer.
Without this patch, mach-virt fails to build without something like
mach-vexpress also selected.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Uwe reported a build failure when targetting a NOMMU platform with my
recent prefetch changes:
arch/arm/lib/changebit.S: Assembler messages:
arch/arm/lib/changebit.S:15: Error: architectural extension `mp' is
not allowed for the current base architecture
This is due to use of the .arch_extension mp directive immediately prior
to an ALT_SMP(...) instruction. Whilst the ALT_SMP macro will expand to
nothing if !CONFIG_SMP, gas will still choke on the directive.
This patch fixes the issue by only emitting the sequence (including the
directive) if CONFIG_SMP=y.
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull alpha updates from Matt Turner:
"It contains a few fixes and some work from Richard to make alpha
emulation under QEMU much more usable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: Prevent a NULL ptr dereference in csum_partial_copy.
alpha: perf: fix out-of-bounds array access triggered from raw event
alpha: Use qemu+cserve provided high-res clock and alarm.
alpha: Switch to GENERIC_CLOCKEVENTS
alpha: Enable the rpcc clocksource for single processor
alpha: Reorganize rtc handling
alpha: Primitive support for CPU power down.
alpha: Allow HZ to be configured
alpha: Notice if we're being run under QEMU
alpha: Eliminate compiler warning from memset macro
Pull parisc fixes from Helge Deller:
- revert an access_ok() patch which broke 32bit userspace on 64bit
kernels
- avoid a gcc miscompilation in two internal pa_memcpy() functions by
not inlining those
- do not export the definition of SOCK_NONBLOCK via uapi header (fixes
build of audit package)
- depending on the fault type we now correctly report either SIGBUS or
SIGSEGV
- a small fix to not compare a size_t variable for < 0
* 'parisc-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: size_t is unsigned, so comparison size < 0 doesn't make sense.
parisc: improve SIGBUS/SIGSEGV error reporting
parisc: break out SOCK_NONBLOCK define to own asm header file
parisc: do not inline pa_memcpy() internal functions
Revert "parisc: implement full version of access_ok()"
Pull AVR32 updates from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: uapi: be sure of "_UAPI" prefix for all guard macros
avr32: add kprobe_ctlblk memory struct
avr32: fix out-of-range jump in large kernels
avr32: setup crt for early panic()
Pull vfs bits and pieces from Al Viro:
"Assorted bits that got missed in the first pull request + fixes for a
couple of coredump regressions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fold try_to_ascend() into the sole remaining caller
dcache.c: get rid of pointless macros
take read_seqbegin_or_lock() and friends to seqlock.h
consolidate simple ->d_delete() instances
gfs2: endianness misannotations
dump_emit(): use __kernel_write(), not vfs_write()
dump_align(): fix the dumb braino
Note that pmds[i] is simply uninitialized at that point...
Granted, it's very hard to hit (you need split page locks *and*
kmalloc(sizeof(spinlock_t), GFP_KERNEL) failing), but the code is
obviously bogus.
Introduced by commit 09ef493985 ("x86: add missed
pgtable_pmd_page_ctor/dtor calls for preallocated pmds")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've finally tracked down why my CR signal-unwind test case still
fails on little-endian. The problem turned to be that the kernel
installs a signal trampoline in the vDSO, and provides a DWARF CFI
record for that trampoline. This CFI describes the save location
for CR:
rsave (70, 38*RSIZE + (RSIZE - CRSIZE))
which is correct for big-endian, but points to the wrong word on
little-endian. This is wrong no matter which ABI.
In addition, for the ELFv2 ABI, we should not only provide a CFI
record for register 70 (cr2), but for all CR fields separately.
Strictly speaking, I guess this would mean providing two separate
vDSO images, one for ELFv1 processes and one for ELFv2 processes (or
maybe playing some tricks with conditional DWARF expressions).
However, having CFI records for the other CR fields in ELFv1 is not
actually wrong, they just will be ignored. So it seems the simplest
fix would be just to always provide CFI for all the fields.
Signed-off-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the little endian support merged, we can add the
CONFIG_CPU_LITTLE_ENDIAN kernel config option.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel doesn't build correctly using the ELFv2 ABI. This patch
ensures that the ELFv1 ABI is used when building a kernel with an
ELFv2 enabled compiler.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
For the ELFv2 ABI, the hander is the entry point, not a function descriptor.
We also need to set up r12, and fortunately the fast_exception_return
exit path restores r12 for us so nothing else is required.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No function descriptor, but we set r12 up and set TIF_RESTOREALL as it
normally isn't restored on return from syscall.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We leave it at zero (though it could be 1) for old tasks.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Boris BREZILLON