There should be no nodes that are not children of the mbus. Move
the nand node under the mbus, and rework the board .dts files
to use an & reference to the nand node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
but most of this is around legacy code and board support. We've found that
platform maintainers have a hard time separating all of these out and might
move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and clocksource
setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
- New backlight drivers for backlights used on Renesas shmobile platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for others in
the same mach directory. More in 2.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=EGua
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds mv643xx_eth and mvmdio device tree nodes for DT enabled
Kirkwood boards. Phy nodes are also added with reg property set on a
per-board basis.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Kirkwood-based PlatHome OpenBlocks A6 board has an Init button
connected to MPP pin 38. This commit adds support for this button.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Instead of having one separate pinmux configuration for each LED, for
each GPIO of the GPIO header, for each DIP switch, this patch groups
them together in configurations that make sense together: LEDs on one
side, GPIOs of the GPIO header on another side, and DIP switches on
yet another side.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When DT support for kirkwood was first introduced, there was no clock
infrastructure. As a result, we had to manually pass the
clock-frequency to the driver from the device node.
Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.
The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.
Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.
Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
OpenBlocks A6 has three leds via GPIO. This supports them.
And this fix typo about led, because hardware manual has typo.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
OpenBlocks A6 uses second I2C with RTC of s35390a.
This supports them.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add support for Plat'Home OpenBlocks A6 using the device tree
where possible.
This commit supports SATA, USB, ether and serial console.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Jason Gunthorpe