This patch adds a separate driver for the MDIO interface of the
Hisilicon Fast Ethernet MAC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the PHY control register, the FIFO depth bits are
written without reading the previous register value, i.e. all other
bits are overwritten with zero. This disables automatic MDI-X
configuration, which is enabled by default. Fix initialization by doing
a read/modify/write operation.
Signed-off-by: Stefan Hauser <stefan@shauser.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1111 currently uses the generic marvell config ANEG function.
This function has a sequence accessing Page 5 and Register 31,
both of which are not defined or reserved for this PHY.
Hence this patch adds a new config ANEG function for Marvell 88E1111
without these erroneous accesses.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a system which uses fixed PHY devices and calls
fixed_phy_register() then fixed_phy_unregister() we can exhaust the
number of fixed PHYs available after a while, since we keep incrementing
the variable phy_fixed_addr, but we never decrement it.
This patch fixes that by converting the fixed PHY allocation to using
IDA, which takes care of the allocation/dealloaction of the PHY
addresses for us.
Fixes: a759512174 ("net: phy: extend fixed driver with fixed_phy_register()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no prevention of a concurrent call to both fixed_mdio_read()
and fixed_phy_update_state(), which can result in the state being
modified while it's being inspected. Fix this by using a seqcount
to detect modifications, and memcpy()ing the state.
We remain slightly naughty here, calling link_update() and updating
the link status within the read-side loop - which would need rework
of the design to change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generate software phy registers as and when requested, rather than
duplicating the state in fixed_phy. This allows us to eliminate
the duplicate storage of of the same data, which is only different
in format.
As fixed_phy_update_regs() no longer updates register state, rename
it to fixed_phy_update().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate out the generation of MII registers from the state validation.
This allows us to simplify the error handing in fixed_phy() by allowing
earlier error detection.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the swphy register generation to tabular form which allows us
to eliminate multiple switch() statements. This results in a smaller
object code size, more efficient, and easier to add support for faster
speeds.
Before:
Idx Name Size VMA LMA File off Algn
0 .text 00000164 00000000 00000000 00000034 2**2
text data bss dec hex filename
388 0 0 388 184 swphy.o
After:
Idx Name Size VMA LMA File off Algn
0 .text 000000fc 00000000 00000000 00000034 2**2
5 .rodata 00000028 00000000 00000000 00000138 2**2
text data bss dec hex filename
324 0 0 324 144 swphy.o
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fixed_phy MII register generation to a library to allow other
software phy implementations to use this code.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest changes to the MDIO code introduced a false-positive
warning with gcc-6 (possibly others):
drivers/net/phy/mdio-mux.c: In function 'mdio_mux_init':
drivers/net/phy/mdio-mux.c:188:3: error: 'parent_bus_node' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It's easy to avoid the warning by making sure the parent_bus_node
is initialized in both cases at the start of the function, since
the later 'of_node_put()' call is also valid for a NULL pointer
argument.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f20e6657a8 ("mdio: mux: Enhanced MDIO mux framework for integrated multiplexers")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the PHY LED registers for the Marvell 88E1510 and others is
not possible, because regardless of the values in marvell,reg-init, it
is later overridden in m88e1121_config_aneg with a non-standard default.
This patch moves that default configuration to .config_init to allow
setting the LED configuration through marvell,reg-init in the device
tree, which should override said default if it exists.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
iProc based SoCs supports the integrated mdio multiplexer which
has the bus selection as well as mdio transaction generation logic
inside.
This multiplexer has child buses for PCIe, SATA, USB and ETH. These
buses could be internal or external to SOC where PHYs are attached.
These buses could use C-45 or C-22 mdio transaction.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An integrated multiplexer uses same address space for
"muxed bus selection" and "generation of mdio transaction"
hence its good to register parent bus from mux driver.
Hence added a mechanism where mux driver could register a
parent bus and pass it down to framework via mdio_mux_init api.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We detected some problems using the smsc lan8720a in combination with
i.MX28 and tracked this down to commit 2100968666 ("net: phy: smsc: move
smsc_phy_config_init reset part in a soft_reset function")
With 2100968666 the generic soft reset is replaced by a specific function
which handles power down state correctly. But additionally the soft reset
itself got conditional and is therefore also only performed if the phy is
in power down state.
This patch keeps the conditional wake up from power down, but
re-introduces the unconditional soft reset using the generic soft reset
function.
It was tested on linux-4.1.25 and linux-4.7.0-rc2.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Intel (former Lantiq) XWAY 11G and 22E PHYs.
These PHYs are also named PEF 7061, PEF 7071, PEF 7072.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit da47b45720 ("phy: add support for a reset-gpio specification")
causes the following xtensa qemu crash according to Guenter Roeck:
[ 9.366256] libphy: ethoc-mdio: probed
[ 9.367389] (null): could not attach to PHY
[ 9.368555] (null): failed to probe MDIO bus
[ 9.371540] Unable to handle kernel paging request at virtual address 0000001c
[ 9.371540] pc = d0320926, ra = 903209d1
[ 9.375358] Oops: sig: 11 [#1]
This reverts commit da47b45720.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since e7f4dc3536 ("mdio: Move allocation of interrupts into core"),
platforms which call fixed_phy_add() before fixed_mdio_bus_init() is
called (for example, because the platform code and the fixed_phy driver
use the same initcall level) crash in fixed_phy_add() since the
->mii_bus is not allocated.
Also since e7f4dc3536, these interrupts are initalized to polling by
default. The few (old) platforms which directly use fixed_phy_add()
from their platform code all pass PHY_POLL for the irq argument, so we
can keep these platforms not crashing by simply not attempting to set
the irq if PHY_POLL is passed.
Also, even if problems have not been reported on more modern platforms
which used fixed_phy_register() from drivers' probe functions, we return
-EPROBE_DEFER if the MDIO bus is not yet registered so that the probe is
retried later.
Fixes: e7f4dc3536 ("mdio: Move allocation of interrupts into core")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If you compile without OF_MDIO support in an RGMII configuration, we fail
to configure the dp83867 phy today by writing garbage into its configuration
registers.
On the other hand if you do compile with OF_MDIO and the phy gets loaded via
device tree, you have to have the properties set in the device tree, otherwise
we fail to load the driver and don't even attach the generic phy driver to
the interface anymore.
To make things slightly more consistent, make the rgmii configuration properties
optional and allow a user to omit them in their device tree.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF_MDIO is configured as module, the #define for it really
is CONFIG_OF_MDIO_MODULE, not CONFIG_OF_MDIO. So if we are compiling it
as module, the dp83867 doesn't see that OF_MDIO was selected and doesn't
read the dt rgmii parameters.
The fix is simple: Use IS_ENABLED(). It checks for both - module as well
as compiled in code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function declares the 'err' local variable for no good reason, get rid
of it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both these functions declare the 'err' local variables for no good reason,
get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The framework only asserts (for now) that the reset gpio is not active.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the hardcoded mask 0x00fffff0 with MICREL_PHY_ID_MASK for
better readability.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy was suspended and is starting, current driver always enable
phy's interrupts, if phy works in polling, phy can raise unexpected
interrupt which will not be handled, the interrupt will block system
enter suspend again. So interrupts should only be re-enabled if phy
works in interrupt.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool callbacks {get|set}_link_ksettings are often the same, so
we add two generics functions phy_ethtool_{get|set}_link_ksettings
to avoid writing severals times the same function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-By: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've finally noticed that mdiobus_scan() also returns either NULL or error
value on failure. Return ERR_PTR(-ENODEV) instead of NULL since this is
the error value already filtered out by the callers that want to ignore
the MDIO address scan failure...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b74766a0a0 ("phylib: don't return NULL
from get_phy_device()") in linux-next, phy_get_device() will return
ERR_PTR(-ENODEV) instead of NULL if the PHY device ID is all ones.
This causes problem with stmmac driver and likely some other drivers
which call mdiobus_register(). I triggered this bug on SoCFPGA MCVEVK
board with linux-next 20160427 and 20160428. In case of the stmmac, if
there is no PHY node specified in the DT for the stmmac block, the stmmac
driver ( drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c function
stmmac_mdio_register() ) will call mdiobus_register() , which will
register the MDIO bus and probe for the PHY.
The mdiobus_register() resp. __mdiobus_register() iterates over all of
the addresses on the MDIO bus and calls mdiobus_scan() for each of them,
which invokes get_phy_device(). Before the aforementioned patch, the
mdiobus_scan() would return NULL if no PHY was found on a given address
and mdiobus_register() would continue and try the next PHY address. Now,
mdiobus_scan() returns ERR_PTR(-ENODEV), which is caught by the
'if (IS_ERR(phydev))' condition and the loop exits immediately if the
PHY address does not contain PHY.
Repair this by explicitly checking for the ERR_PTR(-ENODEV) and if this
error comes around, continue with the next PHY address.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 13a56b44 ("at803x: Add support for hardware reset") added a
work-around for a hardware bug on the AT8030. However, the work-around
was being called for all 803x PHYs, even those that don't need it.
Function at803x_link_change_notify() checks to make sure that it only
resets the PHY on the 8030, but it makes more sense to not call that
function at all if it isn't needed.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that get_phy_device() no longer returns NULL on error, we don't need
to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann asked that get_phy_device() returns either NULL or the error
value, not both on error. Do as he said, return ERR_PTR(-ENODEV) instead
of NULL when the PHY ID registers read as all ones.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8895 driver is using spi_dev_get() apparently just to take a copy
of the SPI device used to instantiate it but never calls spi_dev_put()
to free it. Since the device is guaranteed to exist between probe() and
remove() there should be no need for the driver to take an extra
reference to it so fix the leak by just using a straight assignment.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old ethtool api (get_setting and set_setting) has
generic phy functions phy_ethtool_sset and phy_ethtool_gset.
To supprt the new ethtool api (get_link_ksettings and
set_link_ksettings), we add generic phy function
phy_ethtool_ksettings_get and phy_ethtool_ksettings_set.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tested the PHY SGMII Loopback:
1.set the LOOPBACK bit,
2.set the autoneg to AUTONEG_DISABLE, it calls the
genphy_setup_forced which will clear the bit.
The BMCR_LOOPBACK bit should be preserved.
As Florian pointed out that other bits should be preserved too.
So I make the BMCR_ISOLATE and BMCR_PDOWN as well.
Signed-off-by: Weidong Wang <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO devices can be stacked upon each other. The current code supports
two levels, which until recently has been enough for a DSA mdio bus on
top of another bus. Now we have hardware which has an MDIO mux in the
middle.
Define an MDIO MUTEX class with three levels.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PHY entries for the Broadcom BCM7346 and BCM7362 chips, these are
40nm generation Ethernet PHY.
Fixes: 815717d147 ("net: phy: bcm7xxx: Remove wildcard entries")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the dependency on GPIOLIB for non faulty PHYs.
Indeed, without this patch, if GPIOLIB is not selected
devm_gpiod_get_optional() will return -ENOSYS and the driver probe
call will fail, regardless of the actual PHY hardware.
Out of the 3 PHYs supported by this driver (AT8030, AT8031, AT8035),
only AT8030 presents the issues that commit 13a56b4493 ("net: phy:
at803x: Add support for hardware reset") attempts to work-around by
using a 'reset' GPIO line.
Hence, only AT8030 should depend on GPIOLIB operating properly.
Fixes: 13a56b4493 ("net: phy: at803x: Add support for hardware reset")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver of course "knows" that the chip's reset signal is active low,
so it drives the GPIO to 0 to reset the PHY and to 1 otherwise; however
all this will only work iff the GPIO is specified as active-high in the
device tree! I think both the driver and the device trees (if there are
any -- I was unable to find them) need to be fixed in this case...
Fixes: 13a56b4493 ("net: phy: at803x: Add support for hardware reset")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We could end up dereferencing an error pointer when we call
regulator_disable().
Fixes: 4bdcb1dd9f ('net: Add MDIO bus driver for the Allwinner EMAC')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop two extra occurrences of "on" in option title and help text.
Fixes: 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the code was factored out of mdio-octeon.c, the
MODULE_DESCRIPTION, MODULE_AUTHOR and MODULE_LICENSE annotations were
inadvertently omitted. Restore them so that we don't get kernel taint
warnings upon module loading.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fixed phys delete function simply removed the fixed phy from the
internal linked list and freed the memory. It however did not
unregister the associated phy device. This meant it was still possible
to find the phy device on the mdio bus.
Make fixed_phy_del() an internal function and add a
fixed_phy_unregister() to unregisters the phy device and then uses
fixed_phy_del() to free resources.
Modify DSA to use this new API function, so we don't leak phys.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dongpo Li