This reverts commit 829b6962f7.
Revert this change as it causes a sysfs path to change and therefore
introduces and ABI regression. More precisely Android's vold is not being
able to access /sys/module/mmcblk/parameters/perdev_minors any more, since
the path becomes changed to: "/sys/module/mmc_block/..."
Fixes: 829b6962f7 ("mmc: block: don't use parameter prefix if built as
module")
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Intel BXT/APL use a card detect GPIO however the host controller
will not enable bus power unless it's card detect also reflects
the presence of a card. Unfortunately those 2 things race which
can result in commands not starting, after which the controller
does nothing and there is a 10 second wait for the driver's
10-second timer to timeout.
That is fixed by having the driver look also at the present state
register to determine if the card is present. Consequently, provide
a 'get_cd' mmc host operation for BXT/APL that does that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Drivers may need to provide their own get_cd() mmc host op, but
currently the internals of the current op (sdhci_get_cd()) are
provided by sdhci_do_get_cd() which is also called from
sdhci_request().
To allow override of the get_cd functionality, change sdhci_request()
to call ->get_cd() instead of sdhci_do_get_cd().
Note, in the future the call to ->get_cd() will likely be removed
from sdhci_request() since most drivers don't need actually it.
However this change is being done now to facilitate a subsequent
bug fix.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the past, fixes for specific hardware devices were implemented
in sdhci using quirks. That approach is no longer accepted because
the growing number of quirks was starting to make the code difficult
to understand and maintain.
One alternative to quirks, is to allow drivers to override the default
mmc host operations. This patch makes it easy to do that, and it is
needed for a subsequent bug fix, for which separate patches are
provided.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This used to return -EFAULT, but the function above returns -EINVAL on
the same condition so let's stick to that.
The removal of error return on this path was introduced with b093410c9a
('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD').
Fixes: b093410c9a ('mmc: block: copy resp[] data on err for MMC_IOC_MULTI_CMD').
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Grant Grundler <grundler@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the gpio driver is probed after the mmc one, the read/write gpio
and card detection one return -EPROBE_DEFER. Unfortunately, the memory
region remains requested, and upon the next probe, the probe will fail
anyway with -EBUSY.
Fix this by releasing the memory resource upon probe failure.
More broadly, this patch uses devm_*() primitives whenever possible in
the probe function.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no checks for dma mapping errors in mmc_spi.
Tha patch fixes that and by the way it adds dma_unmap_single(ones_dma)
that was left on a failure path mmc_spi_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device power usage counter is increased by pm_runtime_get_noresume
but isn't decreased in err_add_host error path.
Fix this issue by calling pm_runtime_put_noidle() in the error path to
restore the device's power usage counter.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: f5f17813ae ("mmc: sdhci-of-at91: add PM support)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit fixing the conversion of pxamci to slot-gpio API fixed the
inverted the logic of the read-only gpio. Unfortunately, the commit was
tested on a non-inverted gpio, and not on the inverted one. And the fix
did work partially, by luck.
This is the remaining missing part of the fix, trivial but still necessary.
Fixes: Fixes: 26d49fe719 ("mmc: pxamci: fix read-only gpio detection polarity")
Reported-by: Andrea Adami <andrea.adami@gmail.com>
Tested-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Restore reset-gpios to be optional in pwrseq_simple
- Allow SDIO tuple for CISTPL_SDIO_STD
- Print correct voltage value in debugfs
- Enable tuning according to the actual timing
- Limit SD card power limit according to cards capabilities
MMC host:
- tmio_mmc_dma: don't print invalid DMA cookie
- mmci: Pick the correct variant and allow 8-bit mode for Nomadik
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dHj5
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.5 rc1.
MMC core:
- Restore reset-gpios to be optional in pwrseq_simple
- Allow SDIO tuple for CISTPL_SDIO_STD
- Print correct voltage value in debugfs
- Enable tuning according to the actual timing
- Limit SD card power limit according to cards capabilities
MMC host:
- tmio_mmc_dma: don't print invalid DMA cookie
- mmci: Pick the correct variant and allow 8-bit mode for Nomadik"
* tag 'mmc-v4.5-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: pwrseq_simple: Make reset-gpios optional to match doc
mmc: sdio_cis: fix unknown tuple for CISTPL_SDIO_STD
mmc: debugfs: correct wrong voltage value
mmc: tmio_mmc_dma: don't print invalid DMA cookie
mmc: core: Enable tuning according to the actual timing
mmc: mmci: support 8bit mode on the Nomadik
mmc: mmci: fix an ages old detection error
mmc: sd: limit SD card power limit according to cards capabilities
The DT binding doc says reset-gpios is an optional property but the code
currently bails out if it is omitted.
This is a regression since it breaks previously working device trees.
Fix it by restoring the original documented behaviour.
Fixes: ce03727586 ("mmc: pwrseq_simple: use GPIO descriptors array API")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CISTPL_SDIO_STD(0x91) is a known tuple, but sdio_cis don't define it, so
we get the warning below while probing several sdio wifi cards.
Refer to SDIO spec, it's not needed to parse the tuple, so this patch make
it a known one.
[ 4.098980] mmc2: queuing unknown CIS tuple 0x91 (3 bytes)
[ 4.099033] mmc2: new ultra high speed SDR104 SDIO card at address 0001
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull AVR32 updates from Hans-Christian Noren Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
mmc: atmel: get rid of struct mci_dma_data
mmc: atmel-mci: restore dma on AVR32
avr32: wire up missing syscalls
avr32: wire up accept4 syscall
As struct mci_dma_data is now only used by AVR32, it is nothing but
pointless indirection. Replace it with struct dw_dma_slave in the
AVR32 platform code and with a void pointer elsewhere.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit ecb89f2f5f ("mmc: atmel-mci: remove compat for non DT board
when requesting dma chan") broke dma on AVR32 and any other boards not
using DT. This restores a fallback mechanism for such cases.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The tmio_mmc_start_dma_{rx,tx} function functions contain debug
code that prints the dma cookie among other things. However,
in case we fall back to PIO mode for some reason, the cookie
variable is never initialized, and gcc warns about this:
In file included from ../include/linux/printk.h:277:0,
from ../include/linux/kernel.h:13,
from ../include/linux/list.h:8,
from ../include/linux/kobject.h:20,
from ../include/linux/device.h:17,
from ../drivers/mmc/host/tmio_mmc_dma.c:13:
../drivers/mmc/host/tmio_mmc_dma.c: In function 'tmio_mmc_start_dma':
../include/linux/dynamic_debug.h:86:3: warning: 'cookie' may be used uninitialized in this function [-Wmaybe-uninitialized]
__dynamic_dev_dbg(&descriptor, dev, fmt, \
^
../drivers/mmc/host/tmio_mmc_dma.c:128:15: note: 'cookie' was declared here
dma_cookie_t cookie;
This modifies the dev_dbg() statements so we only print the cookie
when we are already in the DMA path.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While in sdhci_execute_tuning() the choice whether or not to enable the
tuning is done on the actual timing, in the mmc_sdio_init_uhs_card() the
check is done on the capability of the card.
This difference is causing some issues with some SDIO cards in DDR50
mode where the CDM19 is wrongly issued.
With this patch we modify the check in both
mmc_(sd|sdio)_init_uhs_card() functions to take the proper decision
only according to the actual timing specification.
Cc: stable@vger.kernel.org
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 4956e10903 ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.
Cc: stable@vger.kernel.org
Fixes: 34fd421349 ("ARM: 7378/1: mmci: add support for the Nomadik...")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD card specification allows cards to error out a SWITCH command
where the requested function in a group is not supported. The spec
provides for a set of capabilities which indicate which functions are
supported.
In the case of the power limit, requesting an unsupported power level
via the SWITCH command fails, resulting in the power level remaining at
the power-on default of 0.72W, even though the host and card may support
higher powers levels.
This has been seen with SanDisk 8GB cards, which support the default
0.72W and 1.44W (200mA and 400mA) in combination with an iMX6 host,
supporting up to 2.88W (800mA). This currently causes us to try to set
a power limit function value of '3' (2.88W) which the card errors out
on, and thereby causes the power level to remain at 0.72W rather than
the desired 1.44W.
Arrange to limit the selected current limit by the capabilities reported
by the card to avoid the SWITCH command failing. Select the highest
current limit that the host and card combination support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes: a39ca6ae0a ("mmc: core: Simplify and fix for SD switch processing")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The misc control register is 32bit wide, the used readw/writew
accessors only mainipulate the low 16bit of this register. It
currently doesn't matter as all the bit changed are located in
the lower half, but together with the u32 variable used to hold
the contents of the register it is seriously confusing.
Switch to 32bit accessors to avoid any future breakage.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Keep the quirk bits, as Tegra30 and Tegra114 host have different levels
of support for UHS-I modes and so need different spare bits to be set,
but change the logic to be positive.
Tegra210 needs a different tuning sequence than Tegra30+. Disable
UHS modes until support for this is properly added.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This implements the UHS tuning sequence in a similar way to the one
contained in the TRM. It deviates in the way how to check if the tap
value is passing, by using the common Linux MMC function, which does
not only check for data CRC errors, but also if the received block
pattern is correct.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Tegra30 and up TRM states that this bit should always be
programmed to 0 by driver software.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow the the driver to change the clock supplied from the CAR directly,
minimizing the need to divide the clock inside the SDMMC module itself.
This allows for higher clock speeds than the default 48MHz supplied to
the module and is a prerequisite to support DDR signaling modes, where
the Tegra host needs to be run with a fixed internal divider of 2 for
data to be sampled correctly. (Tegra K1 TRM v03p chapter 29.7.1.1)
Also enable the broken preset value quirk as the preset values need to
be adapted to the changed clocking. While Tegra114+ allows this through
vendor registers, there is no such way for Tegra30. Takes the easy way
out and keep things consistent between the different SoC generations by
flagging the preset registers as unusable.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After commit 52221610dd ("mmc: sdhci: Improve external VDD regulator
support"), for the VDD is supplied via external regulators, we ignore
the code to convert a VDD voltage request into one of the standard
SDHCI voltage levels, then program it in the SDHCI_POWER_CONTROL. This
brings two issues:
1. SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON quirk isn't handled properly any
more.
2. What's more, once SDHCI_POWER_ON bit is set, some controllers such
as the sdhci-pxav3 used in marvell berlin SoCs require the voltage
levels programming in the SDHCI_POWER_CONTROL register, even the VDD
is supplied by external regulator. So the host in marvell berlin SoCs
still works fine after the commit. However, commit 3cbc6123a9 ("mmc:
sdhci: Set SDHCI_POWER_ON with external vmmc") sets the SDHCI_POWER_ON
bit, this would make the host in marvell berlin SoCs won't work any
more with external vmmc.
This patch restores the behavior when setting VDD through external
regulator by moving the call of mmc_regulator_set_ocr() to the end
of sdhci_set_power() function.
After this patch, the sdcard on Marvell Berlin SoC boards work again.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Fixes: 52221610dd ("mmc: sdhci: Improve external VDD ...")
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A card can be removed while it is runtime suspended.
Do not print an error message.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is quite common for Android devices to utilize more
then 8 partitions on internal eMMC storage.
The vanilla kernel can support this via
CONFIG_MMC_BLOCK_MINORS, however that solution caps the
system to 256 minors total, which limits the number of
mmc cards the system can support.
This patch, which has been carried for quite awhile in
the AOSP common tree, provides an alternative solution
that doesn't seem to limit the total card count. So I
wanted to submit it for consideration upstream.
This patch sets the GENHD_FL_EXT_DEVT flag, which will
allocate minor number in major 259 for partitions past
disk->minors.
It also removes the use of disk_devt to determine devidx
from md->disk. md->disk->first_minor is always initialized
from devidx and can always be used to recover it.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Austin S Hemmelgarn <ahferroin7@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Android Kernel Team <kernel-team@android.com>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Colin Cross <ccross@android.com>
[jstultz: Added context to commit message]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc workqueue is an ordered workqueue, allowing only one work to
execute per given time. As this workqueue is used for card detection, the
conseqeunce is that cards will be detected one by one waiting for each
other.
Moreover, most of the time spent during card initialization is waiting for
the card's internal firmware to be ready. From a CPU perspective this
typically means waiting for a completion variable to be kicked via an
IRQ-handler or waiting for a sleep timer to finish.
This behaviour of detecting/initializing cards is sub-optimal, especially
for SOCs having several controllers/cards.
Let's convert to use the system_freezable_wq for the mmc detect works.
This enables several works to be executed simultaneously and thus also
cards to be detected like so.
Tests on UX500, which holds two eMMC cards and an SD-card (actually also
an SDIO card, currently not detected), shows a significant improved
behaviour due to this change.
Before this change, both the eMMC cards waited for the SD card to be
initialized as its detect work entered the workqueue first. In some cases,
depending on the characteristic of the SD-card, they got delayed 1-1.5 s.
Additionally for the second eMMC, it needed to wait for the first eMMC to
be initialized which added another 120-190 ms.
Converting to the system_freezable_wq, removed these delays and made both
the eMMC cards available far earlier in the boot sequence.
Selecting the system_freezable_wq, in favour of for example the system_wq,
is because we need card detection mechanism to be disabled once userspace
are frozen during system PM. Currently the mmc core deal with this via PM
notifiers, but following patches may utilize the behaviour of the
system_freezable_wq, to simplify the use of the PM notifiers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Alan Cooper <alcooperx@gmail.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there is a time window between __mmc_send_status() and time_afer(),
on some eMMC chip, the timeout_ms is only 10ms, if this thread was
scheduled out during this period, then, even card has already changes
to transfer state by the result of CMD13, this part of code also treat
it to timeout error.
So, need calculate timeout first, then call __mmc_send_status(), if
already timeout and card still in programing state, then treat it to
the real timeout error.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug
print") fixed one NULL pointer dereference but unfortunately introduced
another. "data" may be NULL if this is a command timeout for a command
without any data, so we should only use it if we're actually waiting for
data.
Fixes: bb08a7d489 ("mmc: usdhi6rol0: fix NULL pointer deref in debug print")
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If no primary handler is specified for threaded_irq then a
default one is assigned which always returns IRQ_WAKE_THREAD.
This handler requires the IRQF_ONESHOT, because the source of
interrupt is not disabled
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there are too many error logs shown when use CMD21/CMD19 to do tune,
and it will appear at each resume time, print out so many logs to the
uart console cost too mush time. so change it to dev_dbg.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, PM core supports asynchronous suspend/resume mode for devices
during system suspend/resume, and the power state transition of one
device may be completed in separate kernel thread. PM core ensures
all power state transition dependency between devices. This patch
enables MMC/SD/SDIO card and SDIO function devices to suspend/resume
asynchronously. This will take advantage of multicore and improve
system suspend/resume speed. After applying this patch and enabling
all SDIO function's child devices to suspend/resume asynchronously
on ASUS T100TA, the system suspend-to-idle time is reduced from
1645ms to 1108ms, and the system resume time is reduced from 940ms
to 918ms.
Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci has a legacy facility to prevent runtime suspend if the
bus power is on. This is needed in cases where the power to
the card is dependent on the bus power. It is controlled by
a pair of functions: sdhci_runtime_pm_bus_on() and
sdhci_runtime_pm_bus_off(). These functions use a boolean
variable 'bus_on' to ensure changes are always paired.
There is an additional check for 'runtime_suspended' which is
the problem. In fact, its use is ill-conceived as the only
requirement for the logic is that 'on' and 'off' are paired,
which is actually broken by the check, for example if the bus
power is turned on during runtime resume. So remove the check.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The version 3.00 SDHCI spec. was a bit unclear about the
required data alignment for 64-bit DMA, whereas the version
4.10 spec. uses different language and indicates that only
4-byte alignment is required rather than the 8-byte alignment
currently implemented. That make no difference to SD and EMMC
which invariably transfer data in sector-aligned blocks.
However with SDIO, it results in using more DMA descriptors
than necessary. Theoretically that slows DMA slightly although
DMA is not the limiting factor for throughput, so there is no
discernable impact on performance. Nevertheless, the driver
should follw the spec unless there is good reason not to, so
this patch corrects the alignment criterion.
There is a more complicated criterion for the DMA descriptor
table itself. However the table is allocated by dma_alloc_coherent()
which allocates pages (i.e. aligned to a page boundary).
For simplicity just check it is 8-byte aligned, but add a comment
that some Intel controllers actually require 8-byte alignment
even when using 32-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI has built-in DMA called ADMA2. ADMA2 uses a descriptor
table to define DMA scatter-gather. Each desciptor can specify
a data length up to 65536 bytes, however the length field is
only 16-bits so zero means 65536. Consequently, putting zero
when the size is zero must not be allowed. This patch fixes
one case where zero data length could be set inadvertently.
The problem happens because unaligned data gets split and the
code did not consider that the remaining aligned portion might
be zero length. That case really only happens for SDIO because
SD and eMMC cards transfer blocks that are invariably sector-
aligned. For SDIO, access to function registers is done by
data transfer (CMD53) when the register is bigger than 1 byte.
Generally registers are 4 bytes but 2-byte registers are possible.
So DMA of 4 bytes or less can happen. When 32-bit DMA is used,
the data alignment must be 4, so 4-byte transfers won't casue a
problem, but a 2-byte transfer could. However with the introduction
of 64-bit DMA, the data alignment for 64-bit DMA was made 8 bytes,
so all 4-byte transfers not on 8-byte boundaries get "split" into
a 4-byte chunk and a 0-byte chunk, thereby hitting the bug.
In fact, a closer look at the SDHCI specs indicates that only the
descriptor table requires 8-byte alignment for 64-bit DMA. That
will be dealt with in a separate patch, but the potential for a
2-byte access remains, so this fix is needed anyway.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage. However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd. Fix by passing the card's
ocr value which does not have the flag.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver may not be able to set the power correctly but that
is not a reason to BUG().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In some cases, the stronger 33 Ohm driver strength must not be used
so it is not a suitable default. Change it to the standard default
50 Ohm value.
The patch applies to v4.2+ except the file name changed. It is
drivers/mmc/host/sdhci-pci.c prior to v.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit cc4f414c88 ("mmc: mmc: Add driver strength selection")
added driver strength selection for eMMC HS200 and HS400 modes.
That patch also set the driver stength when transitioning through
High Speed mode to HS200/HS400, but driver strength is not defined
for High Speed mode. While the JEDEC specification is not clear
on this point it has been observed to cause problems for some eMMC,
and removing the driver strength setting in this case makes it
consistent with the normal use of High Speed mode.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch introduce a new MMC_CAP2_NO_SDIO cap used to tell the mmc
core to not send SDIO specific commands.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are no in-kernel users of the MVSDIO platform data method
(instantiating from a board file) so just delete this code and
make this a DT-only driver. We depend on OF and check that we have
an OF node in probe().
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson