The internal accounting uses 'timespec' based time stamps, which is
slightly inefficient and also problematic once we get to the time_t
overflow in 2038.
When communicating to the firmware, we even get an open-coded 64-bit
division that prevents the code from being build-tested on 32-bit
architectures and is inefficient due to the double conversion from
64-bit nanoseconds to seconds+nanoseconds and then microseconds.
This changes the code to use ktime_t instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
set_current_task() must be called before schedule_timeout(), for this
driver, in order to avoid incorrect usage, use msleep_interrupt()
instead.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The macro timed_wait_for_timeout() only be used in one function, so move
this marco from header file and change it to a function in ipc.c, where
it is used.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ts_format.reserved is not used anywhere yet, but the compiler generates a
warning when the struct's (uninitialized) field is being copied around
drivers/hid/intel-ish-hid/ipc/ipc.c: In function ‘write_ipc_from_queue’:
drivers/hid/intel-ish-hid/ipc/ipc.c:316: warning: ‘ts_format.reserved’ may be used uninitialized in this function
Avoid this by force-initializing the field to zero.
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When built as a module, modprobe followed by rmmod can fail because
DMA was still active. So to fix this, DMA needs to be disabled during
module exit.
This change disables DMA during modules exit and change the ISH PCI
device status to D3.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new function ish_disable_dma() and move DMA disable operations
here, so that this functionality can be reused.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Same operations are done in ish_hw_start() and _ish_hw_reset() to
wakeup ISH device. Consolidate them by introducing a new function
ish_wakeup() and move the code there.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This layer is responsible for
- Enumerating over PCI bus
- Inform FW about host readiness
- Provide HW interface to transport layer for control and messages
- Interrupt handling and routing
Original-author: Daniel Drubin <daniel.drubin@intel.com>
Reviewed-and-tested-by: Ooi, Joyce <joyce.ooi@intel.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Rann Bar-On <rb6@duke.edu>
Tested-by: Atri Bhattacharya <badshah400@aim.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Arnd Bergmann