The SPI_MCR_PCSIS macro assumes that the controller has a number of chip
select signals equal to 6. That is not always the case, but actually is
described through the driver-specific "spi-num-chipselects" device tree
binding. LS1028A for example only has 4 chip selects.
Don't write to the upper bits of the PCSIS field, which are reserved in
the reference manual.
Fixes: 349ad66c0a ("spi:Add Freescale DSPI driver for Vybrid VF610 platform")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200318001603.9650-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is not using any symbols from the GPIO .h files
so drop them.
It was however implicitly using <linux/pinctrl/consumer.h>
so include that instead.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200317092457.264055-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC controller in Amlogic AXG & G12A is capable of driving the
CLK/MOSI/SS signal lines through the idle state which avoid the signals
floating in unexpected state, is capable of using linear clock divider
to reach a much fine tuned range of clocks, while the old controller only
uses a power of two clock divider, result at a more coarse clock range and
finally is capable of running at 80M clock.
The SPICC controller in Amlogic G12A takes the source clock from a specific
clock instead of the bus clock and has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants. Thus
the burst management is simplified and takes in account a variable FIFO
size.
Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.
Neil Armstrong (7):
spi: meson-spicc: remove unused variables
spi: meson-spicc: support max 80MHz clock
spi: meson-spicc: add min sclk for each compatible
spi: meson-spicc: setup IO line delay
spi: meson-spicc: adapt burst handling for G12A support
dt-bindings: spi: amlogic,meson-gx-spicc: add Amlogic G12A compatible
spi: meson-spicc: add support for Amlogic G12A
Sunny Luo (2):
spi: meson-spicc: enhance output enable feature
spi: meson-spicc: add a linear clock divider support
.../bindings/spi/amlogic,meson-gx-spicc.yaml | 22 +
drivers/spi/Kconfig | 1 +
drivers/spi/spi-meson-spicc.c | 496 +++++++++++++-----
3 files changed, 392 insertions(+), 127 deletions(-)
--
2.22.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-amlogic
to_spi_device() already checks 'dev'. No need to do it before calling
it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200312134507.10000-1-wsa@the-dreams.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the SPICC controllers on the Amlogic G12A SoCs family.
The G12A SPICC controllers inherit from the AXG enhanced registers but
takes an external pclk for the baud rate generator and can achieve up to
166MHz SCLK.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-10-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The G12A SPICC controller variant has a different FIFO size and doesn't
handle the RX Half interrupt the same way as GXL & AXG variants.
Thus simplify the burst management and take in account a variable FIFO
size.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-8-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now the controller can support frequencies higher than 30MHz, we need
the setup the I/O line delays in regard of the SPI clock frequency.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-7-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The G12A SPICC controller variant takes the source clock from a specific
clock instead of the bus clock.
The minimal clock calculus won't work with the G12A support, thus add the
minimal supported clock for each variant and pass this to the SPI core.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-6-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC controller in Meson-AXG is capable of running at 80M clock.
The ASIC IP is improved and the clock is actually running higher than
previous old SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-5-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC controller in Meson-AXG SoC is capable of using
a linear clock divider to reach a much fine tuned range of clocks,
while the old controller only use a power of two clock divider,
result at a more coarse clock range.
Also convert the clock registration into Common Clock Framework.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-4-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC controller in Meson-AXG is capable of driving the CLK/MOSI/SS
signal lines through the idle state (between two transmission operation),
which avoid the signals floating in unexpected state.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Link: https://lore.kernel.org/r/20200312133131.26430-3-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_get_resource_byname() function returns NULL on error, it
doesn't return error pointers.
Fixes: d166a73503 ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200312113154.GC20562@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5pQmYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D9sB/9PBy5hYIWLJOqP3Tegy+si7eEjgYQe
32DvHZRYYL+Oc8OQMGnJYUY5grfriS300TjxeB4MNx8ajVyuaH7e2aIhgTz3oJ6a
YrygFcxEi0LmRT82HyLVxptyblMSo3A8QWOTOqe1aFvJRZjDDKvEIcGCW2RPmtxT
r/EoVVkSv4X+k3GUtYnRBrq12hL+vr1YIjZM05MVu2sDtFXLO2+wotFIODDv15zi
ByBtwhKumKawUOETzGDw4EDV5MJx9nZtswRC4x3hDrLS6au39F/MyP78gpHm8vw+
YfiS5/39rkB6j1QltcP3B9n7joxrgaFAYsLBTZUoE3IjeVTggcKCOSVX
=q5ml
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5pQt4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BFqB/9jBg5bNy9mNXljELZ7RKCtbn9CThYk
NvccckUJnjaTxSccGcGEetfFtoVvM4IJ8ffiL6gBrNDgvuSbedLkboqlftRRbkE2
tvxnfjKGeiVIHXcXG0kzrVMDPPncYy+o8nQMJ8b/v+VFeLah6LCo0nT4t54LPvfZ
52Nncdr8jAnjoet7t2CX2nJrhTOPUGhC7HxbwOyu2HOOd5nWmYAdT4UZo4Vdv1g9
L1knLoZctpvCpql/mUWdOAqQbD0bD0vT3FKQaq6C6kAeE+kMWSGdPgYxyFdBEVXi
uOmaqU7lHt2bsr6TRbOpw4ON0PzQtzZ/YhW2XEPJd6uc3GWy//qEyqgO
=qoqi
-----END PGP SIGNATURE-----
Merge tag 'mtk-mtd-spi-move' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-5.7
spi: Rewrite mtk-quadspi spi-nor driver with spi-mem
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
This is a driver for mtk spi-nor controller using spi-mem interface.
The same controller already has limited support provided by mtk-quadspi
driver under spi-nor framework and this new driver is a replacement
for the old one.
Comparing to the old driver, this driver has following advantages:
1. It can handle any full-duplex spi transfer up to 6 bytes, and
this is implemented using generic spi interface.
2. It take account into command opcode properly. The reading routine
in this controller can only use 0x03 or 0x0b as opcode on 1-1-1
transfers, but old driver doesn't implement this properly. This
driver checks supported opcode explicitly and use (1) to perform
unmatched operations.
3. It properly handles SFDP reading. Old driver can't read SFDP
due to the bug mentioned in (2).
4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops
requires parsing SFDP, which isn't possible in old driver. And
the old driver is only flagged to support 1-1-2 mode.
5. It takes advantage of the DMA feature in this controller for
long reads and supports IRQ on DMA requests to free cpu cycles
from polling status registers on long DMA reading. It achieves
up to 17.5MB/s reading speed (1-4-4 mode) which is way faster
than the old one. IRQ is implemented as optional to maintain
backward compatibility.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need a spi-max-frequency when we specifically request a
spi frequency lower than the max speed of spi host.
This property is already documented as optional property and current
host drivers are implemented to operate at highest speed possible
when spi->max_speed_hz is 0.
This patch makes spi-max-frequency an optional property so that
we could just omit it to use max controller speed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-2-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
By selecting MTD_SPI_NOR for SPI_HISI_SFC_V3XX, we may introduce unmet
dependencies:
WARNING: unmet direct dependencies detected for MTD_SPI_NOR
Depends on [m]: MTD [=m] && SPI_MASTER [=y]
Selected by [y]:
- SPI_HISI_SFC_V3XX [=y] && SPI [=y] && SPI_MASTER [=y] && (ARM64 && ACPI [=y] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Since MTD_SPI_NOR is only selected by SPI_HISI_SFC_V3XX for practical
reasons - slave devices use the spi-nor driver, enabled by MTD_SPI_NOR -
just drop it.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1583948115-239907-1-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct device to request the DMA mapping. Otherwise the IOMMU
doesn't get the mapping and it will generate a page fault.
The error messages look like:
[ 3.008452] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xf9800000, fsynr=0x3f0022, cbfrsynra=0x828, cb=8
[ 3.020123] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xf9800000, fsynr=0x3f0022, cbfrsynra=0x828, cb=8
This was tested on a custom board with a LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200310073313.21277-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
All RSPI variants support setting the polarity of the SSL signal.
Advertize support for active-high chip selects, and configure polarity
according to the state of the flag.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200309171537.21551-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The Rockchip spi binding is updated to yaml and new models
were added. The spi on px30,rk3308 and rk3328 are the same as
other Rockchip based SoCs, so add compatible string for it.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200309151004.7780-1-jbx6244@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There exists a set of SPI controllers on some POWER processors that may
be accessed through the FSI bus. Add a driver to traverse the FSI CFAM
engine that can access and drive the SPI controllers. This driver would
typically be used by a baseboard management controller (BMC).
The SPI controllers operate by means of programming a sequencing engine
which automatically manages the usual SPI protocol buses. The driver
programs each transfer into the sequencer as various operations
specifying the slave chip and shifting data in and out on the lines.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20200306194118.18581-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A selection of small fixes, mostly for drivers, that have arrived since
the merge window. None of them are earth shattering in themselves but
all useful for affected systems.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5iiroTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0ALxB/0TAEys4X1IxDku7N4E9vivlTQP+Yy5
LmJ7Oc+z1aCWX3LrpMa3M9JInnY44iahjariaZgcQ9GXXTO4rEoOSTVL99fXzj0h
wRS23p+h8GNFQ0s6Bzni8HSITz+vzCUJjYQe4i8iJIpQBRIErFSrqzB4uRGd7SPI
PIgYeTSA3rFuVvdAgijRg3hPTW2rpn328G/k35JpUNo9OdZ/v6NDQl1Sbg/FedFu
iY0feUaQ1FafHGkja/+OYN43bCraDo7Fo4COyF9cHGIJ8nBzMZJumhjgei26nviM
OQ15zRewFpnLGlK8ffPykrnynOhqo3GF7JbFWvI5pga/G5XzzLY8mi19
=bFsu
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A selection of small fixes, mostly for drivers, that have arrived
since the merge window. None of them are earth shattering in
themselves but all useful for affected systems"
* tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi_register_controller(): free bus id on error paths
spi: bcm63xx-hsspi: Really keep pll clk enabled
spi: atmel-quadspi: fix possible MMIO window size overrun
spi/zynqmp: remove entry that causes a cs glitch
spi: pxa2xx: Add CS control clock quirk
spi: spidev: Fix CS polarity if GPIO descriptors are used
spi: qup: call spi_qup_pm_resume_runtime before suspending
spi: spi-omap2-mcspi: Support probe deferral for DMA channels
spi: spi-omap2-mcspi: Handle DMA size restriction on AM65x
commit a2ca53b52e ("spi: Add HiSilicon v3xx SPI NOR flash
controller driver") likely inadvertently used a select statement
with a CONFIG_ prefix, remove the prefix.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/f8ac6b32a29b9a05b58a7e58ffe8b780642abbf1.camel@perches.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean <vladimir.oltean@nxp.com>:
From: Vladimir Oltean <vladimir.oltean@nxp.com>
This series aims to remove the most inefficient transfer method from the
NXP DSPI driver.
TCFQ (Transfer Complete Flag) mode works by transferring one word,
waiting for its TX confirmation interrupt (or polling on the equivalent
status bit), sending the next word, etc, until the buffer is complete.
The issue with this mode is that it's fundamentally incompatible with
any sort of batching such as writing to a FIFO. But actually, due to
previous patchset ("Compatible string consolidation for NXP DSPI driver"):
https://patchwork.kernel.org/cover/11414593/
all existing users of TCFQ mode today already support a more advanced
feature set, in the form of XSPI (extended SPI). XSPI brings 2 extra
features:
- Word sizes up to 32 bits. This is sub-utilized today, and acceleration
of smaller-than-32 bpw values is provided.
- "Command cycling", basically the ability to write multiple words in a
row and receiving an interrupt only after the completion of the last
one. This is what enables us to make use of the full FIFO depth of
this controller.
Series was tested on the NXP LS1021A-TSN and LS1043A-RDB boards, both
functionally as well as from a performance standpoint.
The command used to benchmark the increased throughput was:
spidev_test --device /dev/spidev1.0 --bpw 8 --size 256 --cpha --iter 10000000 --speed 20000000
where spidev1.0 is a dummy spidev node, using a chip select that no
peripheral responds to.
On LS1021A, which has a 4-entry-deep FIFO and a less powerful CPU, the
performance increase brought by this patchset is from 2700 kbps to 5800
kbps.
On LS1043A, which has a 16-entry-deep FIFO and a more powerful CPU, the
performance increases from 4100 kbps to 13700 kbps.
On average, SPI software timestamping is not adversely affected by the
extra batching, due to the extra patches.
There is one extra patch which clarifies why the TCFQ users were not
converted to the "other" mode in this driver that makes use of the FIFO,
which would be EOQ mode.
My request to the many people on CC (known users and/or contributors) is
to give this series a test to ensure there are no regressions, and for
the Coldfire maintainers to clarify whether the EOQ limitation is
acceptable for them in the long run.
Vladimir Oltean (12):
spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics
spi: spi-fsl-dspi: Remove unused chip->void_write_data
spi: spi-fsl-dspi: Don't mask off undefined bits
spi: spi-fsl-dspi: Add comments around dspi_pop_tx and dspi_push_rx
functions
spi: spi-fsl-dspi: Rename fifo_{read,write} and {tx,cmd}_fifo_write
spi: spi-fsl-dspi: Implement .max_message_size method for EOQ mode
spi: Do spi_take_timestamp_pre for as many times as necessary
spi: spi-fsl-dspi: Convert TCFQ users to XSPI FIFO mode
spi: spi-fsl-dspi: Accelerate transfers using larger word size if
possible
spi: spi-fsl-dspi: Optimize dspi_setup_accel for lowest interrupt
count
spi: spi-fsl-dspi: Use EOQ for last word in buffer even for XSPI mode
spi: spi-fsl-dspi: Take software timestamp in dspi_fifo_write
drivers/spi/spi-fsl-dspi.c | 421 ++++++++++++++++++++++++-------------
drivers/spi/spi.c | 19 +-
include/linux/spi/spi.h | 3 +-
3 files changed, 288 insertions(+), 155 deletions(-)
--
2.17.1
The SPI bus number is completely optional to Linux, so make the
corresponding device tree property optional as well.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200305115546.31814-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply patch from NXP upstream repo to
Enable the octal combination mode in MCR0
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-3-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply patch from NXP upstream repo to
dynamically allocate AHB memory as needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-2-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull in this patch from NXP's upstream repo to
enable fspi on imx8qxp and imx8mm
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20200126140913.2139260-1-aford173@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Although the SPI system timestamps are supposed to reflect the moment
that the peripheral has received a word rather than the moment when the
CPU has enqueued that word to the FIFO, in practice it is easier to just
record the latter time than the former (with a smaller error).
With the recent migration of TCFQ users from poll back to interrupt mode
(this time for XSPI FIFO), it's wiser to keep the interrupt latency
outside of the measurement of the PTP system timestamp itself. If there
proves to be any constant offset that requires static compensation, that
can always be added later. So far that does not appear to be the case at
least on the LS1021A-TSN board, where testing shows that the phc2sys
offset is able to remain within +/- 200 ns even after 68 hours of
testing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-13-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The EOQ mode has a hardware limitation in that it stops the transmission
(including the deassertion of the chip select signal) once the host CPU
requests end-of-queue for a particular word in the TX FIFO.
And XSPI mode has a limitation in that we need a separate CMD FIFO entry
for the last byte in the buffer, where the chip select signal needs to
be deasserted. It's not a functional limitation, but it's rather clunky
and the fact that we need to halt the pipeline and write a single entry
to the TX FIFO whenever a buffer ends brings the throughput down when
transmitting small buffers.
So the idea here is to use EOQ's limitation in our favor when using XSPI
mode. Stop special-casing that final word in the buffer, and just kill
the chip select signal by issuing an EOQ for that last word. Now it can
be mixed in with all the other words in the current TX FIFO train.
A small trick here is that we still keep using the XSPI-specific
signaling via the CMDTCFQ interrupt in RSER, and not enabling the EOQ
interrupt, in order to avoid hardware weirdness (potential races with
separate interrupts being raised for CMDTCFQ and EOQ for what is in fact
the end of the same transmission). That is just theoretical, but it's
good to be cautious, and the EOQ interrupt isn't needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-12-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, a SPI transfer that is not multiple of the highest supported
word width (e.g. 4 bytes) will be transmitted as follows (assume a
30-byte buffer transmitted through a 32-bit wide FIFO that is 32 bytes
deep):
- First 28 bytes are sent as 7 words of 32 bits each
- Last 2 bytes are sent as 1 word of 16 bits size
But if the dspi_setup_accel function had decided to use a lower
oper_bits_per_word value (16 instead of 32), there would have been
enough space in the TX FIFO to fit the entire buffer in one go (15 words
of 16 bits each).
What we're actually trying to avoid is mixing word sizes within the same
run with the TX FIFO, since there is an erratum surrounding this, and
invalid data might get transmitted.
So this patch adds special cases for when the remaining length of the
buffer can be sent in one go as 8-bit or 16-bit words, otherwise it
falls back to the standard logic of sending as many bytes as possible at
the highest oper_bits_per_word value possible.
The benefit is that there will be one less CMDFQ/EOQ interrupt to
service when the entire buffer is transmitted during a single go, and
that will improve the overall latency of the transfer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-11-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds logic in the driver to transmit SPI buffers that use
bits_per_word=8 with a higher bits_per_word count (multiple of 8).
Currently the following (most common) modes are implemented:
- 8 bits_per_word on 32-bit capable controllers
- 8 bits_per_word on 16-bit capable controllers
- 16 bits_per_word on 32-bit capable controllers
Transfers which are not accelerated are transferred with a hardware
bits_per_word value equal to the one of the SPI transfer.
The difference from just extending bits_per_word=32 at the spi_device
driver level is that endianness is different - the SPI core wants to
treat bits_per_word=32 buffers as arrays of u32 (i.e. words in host CPU
endianness). So to preserve endianness when clumping 8x4 bits into
32-bit words, one must perform conversion between CPU and standard (big)
endianness.
All appearances (both on the wire as well as in the buffers presented to
the peripheral driver) are preserved, just that accesses to the PUSHR
and POPR registers are now more efficient, since the same number of
reads/writes can now carry more data (2x more data on TX, 4x more data
on RX).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-10-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Transfer Complete Flag (TCF) interrupt gets raised after each write
to the TX FIFO (PUSHR) which means that it is not possible to devise a
transfer procedure that makes full utilization of the FIFO depth (4
entries on most controllers, 16 entries on some).
On the other hand, XSPI mode has a feature called "command cycling",
which allows a single TX command to be run for a pre-specified number of
TX words. When the command cycle ends, the Command Transfer Complete
Flag bit asserts and raises an interrupt. The advantage in this mode is
that the TX FIFO can be better utilized (more words can be batched at
once).
Other changes brought by this patch:
- The dspi->rx_end variable has been removed, since now the
dspi_fifo_write function sets up dspi->words_in_flight, so
dspi_fifo_read knows how much to read without overrunning the RX
buffer.
- Stop using poll mode unconditionally for TCFQ mode, since XSPI mode
is a little less efficient than that, and so, poll mode doesn't bring
as many improvements for XSPI.
- Stop relying on the hardware transfer counter (SPI_TCR_GET_TCNT) and
instead increment the message->actual_length based on the newly
introduced dspi->words_in_flight variable.
- The CTARE register is now written in the hotpath instead of just at
transfer init time, since it contains the DTCP field (transfer
preload - the counter indicating how many txdata words will follow),
which is a dynamic value.
Due to the fact that the Chip Select toggling setting is part of the
command written to the TX FIFO, the ending word of each buffer needs to
be sent via its own TX command, so that we have a chance to emit a
1-word command with deasserted PCS.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-9-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When dealing with a SPI controller driver that is sending more than 1
byte at once (or the entire buffer at once), and the SPI peripheral
driver has requested timestamping for a byte in the middle of the
buffer, we find that spi_take_timestamp_pre never records a "pre"
timestamp.
This happens because the function currently expects to be called with
the "progress" argument >= to what the peripheral has requested to be
timestamped. But clearly there are cases when that isn't going to fly.
And since we can't change the past when we realize that the opportunity
to take a "pre" timestamp has just passed and there isn't going to be
another one, the approach taken is to keep recording the "pre" timestamp
on each call, overwriting the previously recorded one until the "post"
timestamp is also taken.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-8-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When it gets set, End Of Queue Flag halts the DSPI controller and forces
the chip select signal to deassert.
This operating mode is not ideal, but it is used for the DSPI
instantiations where there is no other notification from the controller
that the data in the FIFO has finished transmission. So in practice, it
means that transmitting buffers larger than the FIFO size will yield
unpredictable results.
The only controller that operates in EOQ mode is MCF5441X (Coldfire). I
would say that the way EOQ is used (and documented in the reference
manual, too) on this chip is incorrect, and I would personally migrate
it to TCFQ, but that's notably worse in terms of performance (it can
only use 1 entry of the 16-deep FIFO) and if this limitation didn't
bother any Coldfire DSPI user so far, it's likely that we just need to
throw an error for larger buffers to make sure that callers are aware
their transfers are getting truncated/split.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-7-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
These function names are very generic and it is easy to get confused.
Rename them after the hardware register that they are accessing.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-6-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Their names are confusing, since dspi_pop_tx prepares a word to be
written to the PUSHR register, and dspi_push_rx gets a word from the
POPR register.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-5-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a useless operation, and if the driver needs to do that, there's
something deeply wrong going on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-4-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This variable has been present since the initial submission of the
driver, and held, for some reason, the value of zero, to be sent on the
wire in the case there wasn't any TX buffer for the current transfer.
Since quite a while now, however, it isn't doing anything at all.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-3-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reduce the if-then-else-if-then-else sequence to:
- a simple division in the case of bytes_per_word calculation
- a memcpy command with a variable size. The semantics of larger-than-8
xfer->bits_per_word is that those words are to be interpreted and
transmitted in CPU native endianness.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20200304220044.11193-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series makes room in the driver for differentiation between the
controllers which currently operate in TCFQ mode. Most of these are
actually capable of a lot more in terms of throughput. This is in
preparation of a second series which will convert the remaining users of
TCFQ mode altogether to XSPI mode with command cycling.
Vladimir Oltean (6):
doc: spi-fsl-dspi: Add specific compatibles for all Layerscape SoCs
spi: spi-fsl-dspi: Use specific compatible strings for all SoC
instantiations
spi: spi-fsl-dspi: Parameterize the FIFO size and DMA buffer size
spi: spi-fsl-dspi: LS2080A and LX2160A support XSPI mode
spi: spi-fsl-dspi: Support SPI software timestamping in all non-DMA
modes
spi: spi-fsl-dspi: Convert the instantiations that support it to DMA
.../devicetree/bindings/spi/spi-fsl-dspi.txt | 17 +-
drivers/spi/spi-fsl-dspi.c | 162 +++++++++++++-----
2 files changed, 128 insertions(+), 51 deletions(-)
--
2.17.1
The A-011218 eDMA/DSPI erratum affects most of the older Layerscape SoCs
with DSPI, and its workaround is a bit intrusive.
After this patch, there are no users of TCFQ mode that don't also
support XSPI (previously there was LS2085A).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20200302001958.11105-7-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no reason to keep this .ptp_sts_supported property explicitly in
devtype_data, since it can be deduced from the operating mode alone.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20200302001958.11105-6-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
XSPI allows for 2 extra features:
- Command cycling (use a single TX command with more than 1 word in the
TX FIFO).
- Increased word size (from 16 bits to 32 bits)
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20200302001958.11105-5-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Get rid of the ifdef for Coldfire and make these hardware
characteristics part of dspi->devtype_data.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20200302001958.11105-4-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the device tree bindings submitted in mainline for Layerscape
SoCs look like this:
LS1021A:
compatible = "fsl,ls1021a-v1.0-dspi";
LS1012A:
compatible = "fsl,ls1012a-dspi", "fsl,ls1021a-v1.0-dspi";
LS2085A:
compatible = "fsl,ls2085a-dspi";
LS2088A:
compatible = "fsl,ls2080a-dspi", "fsl,ls2085a-dspi";
LX2160A:
compatible = "fsl,lx2160a-dspi", "fsl,ls2085a-dspi";
LS1043A:
compatible = "fsl,ls1043a-dspi", "fsl,ls1021a-v1.0-dspi";
LS1046A:
compatible = "fsl,ls1021a-v1.0-dspi";
Due to a lack of a more specific compatible string, LS1012A, LS1043A and
LS1046A will fall under the LS1021A umbrella, and LS2088A and LX2160A
under the LS2085A umbrella.
They do work in those modes, but there are slight differences in the
hardware instantiations, mostly related to FIFO sizes (with the more
specific compatible strings, the FIFO size can be increased properly).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-Id: <20200302001958.11105-3-olteanv@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some error paths leave the bus id allocated. As a result the IDR
allocation will fail after a deferred probe. Fix by freeing the bus id
always on error.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Message-Id: <20200304111740.27915-1-aaro.koskinen@nokia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The message of max device speed setting is shown when
an error in spi_setup() occurs.
Instead, it should be shown when the setup call succeeds.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20200229161841.89144-3-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The debug message in spidev_message() can show wrong xfer speed.
It happens if the initial (came from DT) and set with ioctl call spidev
speeds are different (spidev->speed_hz != spi->max_speed_hz) and one
sends a message with ioctl call and the field of speed is uninitialized
(u_tmp->speed_hz == 0).
In this case the kernel shows the spi->max_speed_hz value instead of
correct spidev->speed_hz.
...
set the max speed with an ioctl call:
[ 1227.702714] spidev spi0.0: setup mode 0, 32 bits/w, 20000000 Hz max --> 0
(real speed sets to 20000000Hz)
send a message with an ioctl call:
[ 1227.731801] spidev spi0.0: xfer len 4096 tx 32bits 0 usec 10000000Hz
(debug message shows 10000000Hz that is the original max speed of this
spidev came from DT)
...
Fix the data source for the debug message.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Link: https://lore.kernel.org/r/20200229161841.89144-2-oleksandr.suvorov@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The purpose of commit 0fd85869c2 ("spi/bcm63xx-hsspi: keep pll clk enabled")
was to keep the pll clk enabled through the lifetime of the device.
In order to do that, some 'clk_prepare_enable()'/'clk_disable_unprepare()'
calls have been added in the error handling path of the probe function, in
the remove function and in the suspend and resume functions.
However, a 'clk_disable_unprepare()' call has been unfortunately left in
the probe function. So the commit seems to be more or less a no-op.
Axe it now, so that the pll clk is left enabled through the lifetime of
the device, as described in the commit.
Fixes: 0fd85869c2 ("spi/bcm63xx-hsspi: keep pll clk enabled")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20200228213838.7124-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
As discussed during the original HiSilicon v3xx SPI driver upstreaming,
currently there is no method for the ACPI SPI Serial Bus Connection
Resource Descriptor to define the data buswidth [0], [1].
So we can look to get the ACPI spec updated for this, and I have
submitted a proposal for a new feature here:
https://bugzilla.tianocore.org/show_bug.cgi?id=2557
However I am not sure how successful that will be.
In the meantime, as an alternate approach, this RFC proposes to allow the
SPI controller driver override the device buswidth. In this example,
the driver uses DMI quirks to discover the host machine and set the
buswidth override accordingly when the machine is known to support
dual or quad mode of operation.
I also have included a fix for dual and quad modes in the driver.
Comments welcome. thanks.
[0] https://lore.kernel.org/linux-mtd/20200109212842.GK3702@sirena.org.uk/
[1] https://uefi.org/sites/default/files/resources/ACPI_6_3_final_Jan30.pdf,
19.6.126
John Garry (3):
spi: Allow SPI controller override device buswidth
spi: HiSilicon v3xx: Properly set CMD_CONFIG for Dual/Quad modes
spi: HiSilicon v3xx: Use DMI quirk to set controller buswidth override
bits
drivers/spi/spi-hisi-sfc-v3xx.c | 99 ++++++++++++++++++++++++++++++++-
drivers/spi/spi.c | 4 +-
include/linux/spi/spi.h | 3 +
3 files changed, 104 insertions(+), 2 deletions(-)
--
2.17.1
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
The Huawei D06 board (and variants) can support Quad mode of operation.
Since we have no current method in ACPI SPI bus device resource description
to describe this information, use DMI to detect the board, and set the
controller buswidth override bits.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-4-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CMD_CONFIG register memory interface type field is not set configured
for Dual and Quad modes, so set appropriately.
This was not detected previously as we only ever operated in standard SPI
mode.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-3-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently ACPI firmware description for a SPI device does not have any
method to describe the data buswidth on the board.
So even through the controller and device may support higher modes than
standard SPI, it cannot be assumed that the board does - as such, that
device is limited to standard SPI in such a circumstance.
As a workaround, allow the controller driver supply buswidth override bits,
which are used inform the core code that the controller driver knows the
buswidth supported on that board for that device.
A host controller driver might know this info from DMI tables, for example.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1582903131-160033-2-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The QSPI controller memory space is limited to 128MB:
0x9000_00000-0x9800_00000/0XD000_0000--0XD800_0000.
There are nor flashes that are bigger in size than the memory size
supported by the controller: Micron MT25QL02G (256 MB).
Check if the address exceeds the MMIO window size. An improvement
would be to add support for regular SPI mode and fall back to it
when the flash memories overrun the controller's memory space.
Fixes: 0e6aae08e9 ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200228155437.1558219-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the public interface for chipselect, there is always an entry
commented as "Dummy generic FIFO entry" pushed down to the fifo right
after the activate/deactivate command. The dummy entry is 0x0,
irregardless if the intention was to activate or deactive the cs. This
causes the cs line to glitch rather than beeing activated in the case
when there was an activate command.
This has been observed on oscilloscope, and have caused problems for at
least one specific flash device type connected to the qspi port. After
the change the glitch is gone and cs goes active when intended.
The reason why this worked before (except for the glitch) was because
when sending the actual data, the CS bits are once again set. Since
most flashes uses mode 0, there is always a half clk period anyway for
cs to clk active setup time. If someone would rely on timing from a
chip_select call to a transfer_one, it would fail though.
It is unknown why the dummy entry was there in the first place, git log
seems to be of no help in this case. The reference manual gives no
indication of the necessity of this. In fact the lower 8 bits are a
setup (or hold in case of deactivate) time expressed in cycles. So this
should not be needed to fulfill any setup/hold timings.
Signed-off-by: Thommy Jakobsson <thommyj@gmail.com>
Reviewed-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Link: https://lore.kernel.org/r/20200224162643.29102-1-thommyj@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In some circumstances on Intel LPSS controllers, toggling the LPSS
CS control register doesn't actually cause the CS line to toggle.
This seems to be failure of dynamic clock gating that occurs after
going through a suspend/resume transition, where the controller
is sent through a reset transition. This ruins SPI transactions
that either rely on delay_usecs, or toggle the CS line without
sending data.
Whenever CS is toggled, momentarily set the clock gating register
to "Force On" to poke the controller into acting on CS.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200211223700.110252-1-rajatja@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change broke userspace applications which issue an SPI_IOC_WR_MODE
ioctl() to an spidev: Chip Select polarity will be incorrect unless the
application is changed to set SPI_CS_HIGH. And once changed, it will be
incompatible with kernels not containing the commit.
Fix by setting SPI_CS_HIGH in spidev_ioctl() (under the same conditions
as in of_spi_parse_dt()).
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/fca3ba7cdc930cd36854666ceac4fbcf01b89028.1582027457.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org # v5.1+
spi_qup_suspend() will cause synchronous external abort when
runtime suspend is enabled and applied, as it tries to
access SPI controller register while clock is already disabled
in spi_qup_pm_suspend_runtime().
Signed-off-by: Yuji sasaki <sasakiy@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200214074340.2286170-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
All RSPI variants support selecting the word order.
Advertize support for LSB-first order, and act upon the flag being set.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218105810.902-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Basic SPI features like clock phase/polarity and loopback mode are
common to all RSPI variants. Factor them out to reduce duplication.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200218105810.902-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Call cpu_latency_qos_add/remove_request() instead of
pm_qos_add/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Add a SPI device driver that sits in-band and provides a SPI controller
which supports chip selects via a mux-control. This enables extra SPI
devices to be connected with limited native chip selects.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200204032838.20739-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for SPI controller found in Qualcomm Atheros
AR934x/QCA95xx SoCs.
This controller is a superset of the already supported qca,ar7100-spi.
Besides the bit-bang mode in spi-ath79.c, this new controller added
a new "shift register" mode, allowing faster spi operations.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200210034152.49063-2-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver doesn't call any DT functions like of_get_property(). Remove
the of.h include as it isn't used.
Cc: Girish Mahadevan <girishm@codeaurora.org>
Cc: Dilip Kota <dkota@codeaurora.org>
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200204191206.97036-4-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Changes stm32 QSPI driver to defer its probe operation when a reset
controller device have not yet probed but is registered in the
system.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200203135048.1299-2-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some lines are long here. Use a struct dev pointer to shorten lines and
simplify code. The clk_get() call can fail because of EPROBE_DEFER
problems too, so just remove the error print message because it isn't
useful.
Cc: Girish Mahadevan <girishm@codeaurora.org>
Cc: Dilip Kota <dkota@codeaurora.org>
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200204191206.97036-3-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to force IRQF_TRIGGER_HIGH here as the DT or ACPI tables
should take care of this for us. Just use 0 instead so that we use the
flags from the firmware.
Cc: Girish Mahadevan <girishm@codeaurora.org>
Cc: Dilip Kota <dkota@codeaurora.org>
Cc: Alok Chauhan <alokc@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200204191206.97036-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_channel() can return -EPROBE_DEFER, if DMA driver is not
ready. Currently driver just falls back to PIO mode on probe deferral.
Fix this by requesting all required channels during probe and
propagating EPROBE_DEFER error code.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-3-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On AM654, McSPI can only support 4K - 1 bytes per transfer when DMA is
enabled. Therefore populate master->max_transfer_size callback to
inform client drivers of this restriction when DMA channels are
available.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200204124816.16735-2-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 84d043185d ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Improving spi 8 bit per word mode transfer performance
by using 16 bit per word transfer and receive when the data
length is even and larger than one.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20200115162301.235926-3-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-ti-qspi.c: In function ‘ti_qspi_start_transfer_one’:
drivers/spi/spi-ti-qspi.c:392:8: warning: ‘rx_wlen’ may be used uninitialized in this function [-Wmaybe-uninitialized]
392 | if (rx_wlen >= 32)
| ^
drivers/spi/spi-ti-qspi.c:318:12: note: ‘rx_wlen’ was declared here
318 | u8 rxlen, rx_wlen;
| ^~~~~~~
The warning is a false positive; it is not thrown by all compiler versions, e.g.
Red Hat Cross 9.2.1-1 but not Linaro GCC 7.5-2019.12.
Signed-off-by: Jean Pihet <jean.pihet@newoldbits.com>
Link: https://lore.kernel.org/r/20200115100700.3357-1-jean.pihet@newoldbits.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixing NPCM BMC Peripheral SPI controller 16 bit
send and receive support by writing and reading
the SPI data in the right order.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20200115162301.235926-2-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Intel Comet Lake PCH-V which has the same LPSS than on
Intel Kaby lake unlike other Intel Comet Lake PCH variants that are based
on Intel Cannon Lake PCH LPSS.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200116091035.575175-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Why it does not work at the moment:
- num_chipselect sets the number of cs-gpios that are in the DT.
This comes from drivers/spi/spi.c
- num_chipselect gets set with devm_spi_register_controller, that is
called in drivers/spi/spi.c
- devm_spi_register_controller got called after num_chipselect has
been used.
How this commit fixes the issue:
- devm_spi_register_controller gets called before num_chipselect is
being used.
Fixes: c7a4025995 ("spi: lpspi: use the core way to implement cs-gpio function")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20191204141312.1411251-1-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Optimize the 8-bit based transfers, as used by the SPI flash
devices, by reading the data registers by 32 and 128 bits when
possible and copy the contents to the receive buffer.
The speed improvement is 4.9x using quad read.
Signed-off-by: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Ryan Barnett <ryan.barnett@rockwellcollins.com>
Cc: Conrad Ratschan <conrad.ratschan@rockwellcollins.com>
Cc: Arnout Vandecappelle <arnout.vandecappelle@essensium.com>
Link: https://lore.kernel.org/r/20200114124125.361429-3-jean.pihet@newoldbits.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The TI QSPI IP has limitations:
- the MMIO region is 64MB in size
- in non-MMIO mode, the transfer can handle 4096 words max.
Add support for bigger devices.
Use MMIO and DMA transfers below the 64MB boundary, use
software generated transfers above.
Signed-off-by: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Ryan Barnett <ryan.barnett@rockwellcollins.com>
Cc: Conrad Ratschan <conrad.ratschan@rockwellcollins.com>
Cc: Arnout Vandecappelle <arnout.vandecappelle@essensium.com>
Link: https://lore.kernel.org/r/20200114124125.361429-2-jean.pihet@newoldbits.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currrently the memory for the clk_bulk_data of the QSPI controller
is allocated with spi_alloc_master(). The bulk data pointer is passed
to devm_clk_bulk_get() which saves it in clk_bulk_devres->clks. When
the device is removed later devm_clk_bulk_release() is called and
uses the bulk data referenced by the pointer to release the clocks.
For this driver this results in accessing memory that has already
been freed, since the memory allocated with spi_alloc_master() is
released by spi_controller_release(), which is called before the
managed resources are released.
Use device managed memory for the clock bulk data to fix the issue
described above.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200108133948.1.I35ceb4db3ad8cfab78f7cd51494aeff4891339f5@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the driver for the HiSilicon v3xx SPI NOR flash controller, commonly
found in hi16xx chipsets.
This is a different controller than that in drivers/mtd/spi-nor/hisi-sfc.c;
indeed, the naming for that driver is poor, since it is really known as
FMC, and can support other memory technologies.
The driver module name is "hisi-sfc-v3xx", as recommended by HW designer,
being an attempt to provide a distinct name - v3xx being the unique
controller versioning.
Only ACPI firmware is supported.
DMA is not supported, and we just use polling mode for operation
completion notification.
The driver uses the SPI MEM OPs.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1575900490-74467-3-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The "RevPi Connect Flat" PLC offered by KUNBUS has 4 slaves attached
to the BCM2835 SPI master. Raise the maximum number of slaves in the
driver accordingly.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/01453fd062de2d49bd74a847e13a0781cbf8143d.1578572268.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
STR is a well-known stringify macro so it should be avoided in drivers
to avoid warnings like this (MIPS architecture while compile testing):
drivers/spi/spi-sh-msiof.c:76:0: warning: "STR" redefined
#define STR 0x40 /* Status Register */
arch/mips/include/asm/mipsregs.h:30:0: note: this is the location of the previous definition
#define STR(x) __STR(x)
To maintain consistency between all register names add a SI prefix to
all of them. This also matches register names in datasheet.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200108194319.3171-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for GPIO chip selects using GPIO descriptors. As the RSPI
controller always drives a native chip select when performing a
transfer, at least one native chip select must be left unused.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-7-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
RSPI variants on some SuperH or R-Mobile SoCs support multiple native
chip selects. Add support for this by configuring the SSL Assert Signal
Setting.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-6-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The set_config_register() macro is used in a single place.
Make the code easier to read by just removing it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-5-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the MSIOF SPI driver uses custom code to handle the unused
native chip select with GPIO chip selects.
Convert the driver to use the new generic handling in the SPI core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-3-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI master controllers always drive a native chip select when
performing a transfer. Hence when using both native and GPIO chip
selects, at least one native chip select must be left unused, to be
driven when performing transfers with slave devices using GPIO chip
selects.
Currently, to find an unused native chip select, SPI controller drivers
need to parse and process cs-gpios theirselves. This is not only
duplicated in each driver that needs it, but also duplicates part of the
work done later at SPI controller registration time. Note that this
cannot be done after spi_register_controller() returns, as at that time,
slave devices may have been probed already.
Hence add generic support to the SPI subsystem for finding an unused
native chip select. Optionally, this unused native chip select, and all
other in-use native chip selects, can be validated against the maximum
number of native chip selects available on the controller hardware.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200102133822.29346-2-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Use platform_get_irq_byname_optional() instead of platform_get_irq_byname()
to avoid below error message during probe:
[3.265115] bcm_iproc 68c70200.spi: IRQ spi_lr_fullness_reached not found
[3.272121] bcm_iproc 68c70200.spi: IRQ spi_lr_session_aborted not found
[3.284965] bcm_iproc 68c70200.spi: IRQ spi_lr_impatient not found
[3.291344] bcm_iproc 68c70200.spi: IRQ spi_lr_session_done not found
[3.297992] bcm_iproc 68c70200.spi: IRQ mspi_done not found
[3.303742] bcm_iproc 68c70200.spi: IRQ mspi_halted not found
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Link: https://lore.kernel.org/r/20200107040912.16426-1-rayagonda.kokatanur@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Because of out-of-order execution about some CPU architecture,
In this debug stage we find Completing spi interrupt enable ->
prodrucing TXEI interrupt -> running "interrupt_transfer" function
will prior to set "dw->rx and dws->rx_end" data, so this patch add
memory barrier to enable dw->rx and dw->rx_end to be visible and
solve to send SPI data error.
eg:
it will fix to this following low possibility error in testing environment
which using SPI control to connect TPM Modules
kernel: tpm tpm0: Operation Timed out
kernel: tpm tpm0: tpm_relinquish_locality: : error -1
Signed-off-by: fengsheng <fengsheng5@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Link: https://lore.kernel.org/r/1578019930-55858-1-git-send-email-kong.kongxinwei@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl4TMdwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0M5UB/9w0mzrmuaJzctm3Jm8LiCIjJoZ0woQ
chgbhm2C/I6idENxdUhaJ1YZMI6NkmJKpJy5tQ/QH4MnbOVT/vHIEmIsRYO0vYoF
ApERJLia8da1OpiJlPTbsg3eUXVNmPMVeAkq5MgKSflaIjV6Ejc0FRWmgDYvzhu9
xkCsptAF7MYPUuHdBcjXPscSf1/w+FdDy8VYncEluyJ0NpGDU64N/XdTwRmsG8QW
BxA1jPPKi445NsC+OV8SFfNZbeEXG2iSEBPvp4tMGtd0TiIp3UNLTRzMstEFE6SD
hCzL9fQEzUgHD+B0vLmccyy0HR0phk6813jf9KeToAjAxKtf5XhQajW+
=Ad4n
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small collection of fixes here, one to make the newly added PTP
timestamping code more accurate, a few driver fixes and a fix for the
core DT binding to document the fact that we support eight wire buses"
* tag 'spi-fix-v5.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Document Octal mode as valid SPI bus width
spi: spi-dw: Add lock protect dw_spi rx/tx to prevent concurrent calls
spi: spi-fsl-dspi: Fix 16-bit word order in 32-bit XSPI mode
spi: Don't look at TX buffer for PTP system timestamping
spi: uniphier: Fix FIFO threshold
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
dw_spi_irq() and dw_spi_transfer_one concurrent calls.
I find a panic in dw_writer(): txw = *(u8 *)(dws->tx), when dw->tx==null,
dw->len==4, and dw->tx_end==1.
When tpm driver's message overtime dw_spi_irq() and dw_spi_transfer_one
may concurrent visit dw_spi, so I think dw_spi structure lack of protection.
Otherwise dw_spi_transfer_one set dw rx/tx buffer and then open irq,
store dw rx/tx instructions and other cores handle irq load dw rx/tx
instructions may out of order.
[ 1025.321302] Call trace:
...
[ 1025.321319] __crash_kexec+0x98/0x148
[ 1025.321323] panic+0x17c/0x314
[ 1025.321329] die+0x29c/0x2e8
[ 1025.321334] die_kernel_fault+0x68/0x78
[ 1025.321337] __do_kernel_fault+0x90/0xb0
[ 1025.321346] do_page_fault+0x88/0x500
[ 1025.321347] do_translation_fault+0xa8/0xb8
[ 1025.321349] do_mem_abort+0x68/0x118
[ 1025.321351] el1_da+0x20/0x8c
[ 1025.321362] dw_writer+0xc8/0xd0
[ 1025.321364] interrupt_transfer+0x60/0x110
[ 1025.321365] dw_spi_irq+0x48/0x70
...
Signed-off-by: wuxu.wu <wuxu.wu@huawei.com>
Link: https://lore.kernel.org/r/1577849981-31489-1-git-send-email-wuxu.wu@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When used in Extended SPI mode on LS1021A, the DSPI controller wants to
have the least significant 16-bit word written first to the TX FIFO.
In fact, the LS1021A reference manual says:
33.5.2.4.2 Draining the TX FIFO
When Extended SPI Mode (DSPIx_MCR[XSPI]) is enabled, if the frame size
of SPI Data to be transmitted is more than 16 bits, then it causes two
Data entries to be popped from TX FIFO simultaneously which are
transferred to the shift register. The first of the two popped entries
forms the 16 least significant bits of the SPI frame to be transmitted.
So given the following TX buffer:
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 0x0 | 0x1 | 0x2 | 0x3 | 0x4 | 0x5 | 0x6 | 0x7 | 0x8 | 0x9 | 0xa | 0xb |
+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+-----+
| 32-bit word 1 | 32-bit word 2 | 32-bit word 3 |
+-----------------------+-----------------------+-----------------------+
The correct way that a little-endian system should transmit it on the
wire when bits_per_word is 32 is:
0x03020100
0x07060504
0x0b0a0908
But it is actually transmitted as following, as seen with a scope:
0x01000302
0x05040706
0x09080b0a
It appears that this patch has been submitted at least once before:
https://lkml.org/lkml/2018/9/21/286
but in that case Chuanhua Han did not manage to explain the problem
clearly enough and the patch did not get merged, leaving XSPI mode
broken.
Fixes: 8fcd151d26 ("spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)")
Cc: Esben Haabendal <eha@deif.com>
Cc: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191228135536.14284-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The API for PTP system timestamping (associating a SPI transaction with
the system time at which it was transferred) is flawed: it assumes that
the xfer->tx_buf pointer will always be present.
This is, of course, not always the case.
So introduce a "progress" variable that denotes how many word have been
transferred.
Fix the Freescale DSPI driver, the only user of the API so far, in the
same patch.
Fixes: b42faeee71 ("spi: Add a PTP system timestamp to the transfer structure")
Fixes: d6b71dfaee ("spi: spi-fsl-dspi: Implement the PTP system timestamping for TCFQ mode")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191227012417.1057-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We can catch whether the SPI controller has declared it can take care of
software timestamping transfers, but didn't. So do it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191227012444.1204-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch the OC Tiny driver over to handling CS GPIOs using
GPIO descriptors in the core.
This driver is entirely relying on GPIOs to be used for
chipselect, so let the core pick these out using either
device tree or machine descriptors.
There are no in-tree users of this driver so no board files
need to be patched, out-of-tree boardfiles can use machine
descriptor tables, c.f. commit 1dfbf334f1.
Cc: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191205092411.64341-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds DMA transfer mode support for UniPhier SPI controller.
Since this controller requires simulteaneous transmission and reception,
this indicates SPI_CONTROLLER_MUST_RX and SPI_CONTROLLER_MUST_TX.
Because the supported dma controller has alignment restiction,
there is also a restriction that 'maxburst' parameters in dma_slave_config
corresponds to one word width.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-6-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes coccicheck warning:
drivers/spi/spi-tegra114.c:272:2-17: WARNING: Assignment of 0/1 to bool variable
drivers/spi/spi-tegra114.c:275:2-17: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1577159526-33689-4-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes coccicheck warning:
drivers/spi/spi-imx.c:1233:2-17: WARNING: Assignment of 0/1 to bool variable
drivers/spi/spi-imx.c:1235:2-17: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1577159526-33689-3-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes coccicheck warning:
drivers/spi/spi-fsl-lpspi.c:472:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/spi/spi-fsl-lpspi.c:474:2-19: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1577159526-33689-2-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This changes each argument of functions uniphier_irq_{enable,disable}()
to uniphier_spi_priv because these functions are used not only for
spi_device but also for the entire controller.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Rx threshold means the value to inform the receiver when the number of words
in Rx FIFO is equal to or more than the value. Similarly, Tx threshold means
the value to inform the sender when the number of words in Tx FIFO is equal
to or less than the value. The controller triggers the driver to start
the transfer.
In case of Rx, the driver wants to detect that the specified number of words
N are in Rx FIFO, so the value of Rx threshold should be N. In case of Tx,
the driver wants to detect that the same number of spaces as Rx are in
Tx FIFO, so the value of Tx threshold should be (FIFO size - N).
For example, in order for the driver to receive at least 3 words from
Rx FIFO, set 3 to Rx threshold.
+-+-+-+-+-+-+-+-+
| | | | | |*|*|*|
+-+-+-+-+-+-+-+-+
In order for the driver to send at least 3 words to Tx FIFO, because
it needs at least 3 spaces, set 8(FIFO size) - 3 = 5 to Tx threshold.
+-+-+-+-+-+-+-+-+
|*|*|*|*|*| | | |
+-+-+-+-+-+-+-+-+
This adds new function uniphier_spi_set_fifo_threshold() to set
threshold value to the register.
And more, FIFO counts by 'words', so this renames 'fill_bytes' with
'fill_words', and fixes the calculation using bytes_per_words.
Fixes: 37ffab8170 ("spi: uniphier: introduce polling mode")
Cc: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A relatively large set of fixes here, the biggest part of it is for
fallout from the GPIO descriptor rework that affected several of the
devices with usable native chip select support. There's also some new
PCI IDs for Intel Jasper Lake devices.
The conversion to platform_get_irq() in the fsl driver is an incremental
fix for build errors introduced on SPARC by the earlier fix for error
handling in probe in that driver.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl34xt8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D64B/91GGhGgNybvExhls79YKQx9STnv8Vl
sIVgbnVxnTHrAa+s/5ML0T8LzH9W5KcBUuL+KCd0oMdaE9QZSCKGdraEqDJz7Ie4
iHbBSAtwL0tegbyM+J4oKC3wen3Lg1u1iwn4Plo2fVKEah7zG6gdneQcf454EnEF
om2Sj2K7tqoqN1jIl0j/FGQtlDXvhzp3m+CyGakjzsBvINmSGixrO5Lit/dx3qSf
xkhLDWZqUk3UatusPXhpJJVxWPuVvT5NQkvUYDte1rHxrVdolYQctwBRPN/uZ2hq
FcLzUbWVFx7p3cDqvuQ6XTptpue4njnaPOT/LW6tud4BexlaV1q83XYs
=gPXn
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A relatively large set of fixes here, the biggest part of it is for
fallout from the GPIO descriptor rework that affected several of the
devices with usable native chip select support. There's also some new
PCI IDs for Intel Jasper Lake devices.
The conversion to platform_get_irq() in the fsl driver is an
incremental fix for build errors introduced on SPARC by the earlier
fix for error handling in probe in that driver"
* tag 'spi-fix-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fsl: use platform_get_irq() instead of of_irq_to_resource()
spi: nxp-fspi: Ensure width is respected in spi-mem operations
spi: spi-ti-qspi: Fix a bug when accessing non default CS
spi: fsl: don't map irq during probe
spi: spi-cavium-thunderx: Add missing pci_release_regions()
spi: sprd: Fix the incorrect SPI register
gpiolib: of: Make of_gpio_spi_cs_get_count static
spi: fsl: Handle the single hardwired chipselect case
gpio: Handle counting of Freescale chipselects
spi: fsl: Fix GPIO descriptor support
spi: dw: Correct handling of native chipselect
spi: cadence: Correct handling of native chipselect
spi: pxa2xx: Add support for Intel Jasper Lake
Use dev_dbg() on -EPROBE_DEFER and dev_err() on all
other errors.
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191216230802.45715-2-jquinlan@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fclk and its rate are retrieved from DT.
Signed-off-by: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Ryan Barnett <ryan.barnett@rockwellcollins.com>
Cc: Conrad Ratschan <conrad.ratschan@rockwellcollins.com>
Cc: Arnout Vandecappelle <arnout.vandecappelle@essensium.com>
Link: https://lore.kernel.org/r/20191211193954.747745-2-jean.pihet@newoldbits.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of grabbing GPIOs using the legacy interface and
handling them in the setup callback, just let the core
grab and use the GPIOs using descriptors.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sunny Luo <sunny.luo@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20191205083915.27650-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-10-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-9-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-8-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-7-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-6-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA channel was not released if either devm_request_irq() or
devm_spi_register_controller() failed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191212135550.4634-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike irq_of_parse_and_map() which has a dummy definition on SPARC,
of_irq_to_resource() hasn't.
But as platform_get_irq() can be used instead and is generic, use it.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Fixes: 3194d2533e ("spi: fsl: don't map irq during probe")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/091a277fd0b3356dca1e29858c1c96983fc9cb25.1576172743.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commits 05104c266a ("ARM: shmobile: r7s72100: genmai: Remove
legacy board file") and a483dcbfa2 ("ARM: shmobile: lager: Remove
legacy board support", RZ/A1 and R-Car Gen2 SoCs are only supported in
generic DT-only ARM multi-platform builds. The driver doesn't need to
match platform devices by name anymore for these platforms, hence remove
the corresponding platform_device_id entries.
The platform_device_id entry for "rspi" is retained, as it is used by
the SH7757 platform, which hasn't been converted to DT yet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/20191211131553.23960-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
If dws is NULL in dw_spi_host_add(), we return the error to the
upper callers instead of crashing. The patch replaces BUG_ON by
returning -EINVAL to the caller.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Link: https://lore.kernel.org/r/20191205231421.9333-1-pakki001@umn.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
When switching ChipSelect from default CS0 to any other CS, driver fails
to update the bits in system control module register that control which
CS is mapped for MMIO access. This causes reads to fail when driver
tries to access QSPI flash on CS1/2/3.
Fix this by updating appropriate bits whenever active CS changes.
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191211155216.30212-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ->chipselect() callback on the bit-banged SPI library
master is optional if using GPIO descriptors: when using
descriptors exclusively without any native chipselects,
the core does not even call out the the native ->set_cs()
and therefore ->chipselect() on a bit-banged SPI master
will not even be called in this case.
Make sure to respect the SPI_MASTER_GPIO_SS as used by
e.g. spi-gpio.c though: this setting will make the core
handle the chip select using GPIO descriptors *AND* call
the local chipselect handler.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191205091340.59850-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This switches the STM32 SPI driver over to using GPIO
descriptors for chip select. Instead of the callbacks for
picking the GPIO lines using the legacy API we just let
the core handle it all using descriptors.
Cc: Fabien Dessenne <fabien.dessenne@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191205083401.27077-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075500.18525-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Freescale MPC8xxx had a special quirk for handling a
single hardwired chipselect, the case when we're using neither
GPIO nor native chip select: when inspecting the device tree
and finding zero "cs-gpios" on the device node the code would
assume we have a single hardwired chipselect that leaves the
device always selected.
This quirk is not handled by the new core code, so we need
to check the "cs-gpios" explicitly in the driver and set
pdata->max_chipselect = 1 which will later fall through to
the SPI master ->num_chipselect.
Make sure not to assign the chip select handler in this
case: there is no handling needed since the chip is always
selected, and this is what the old code did as well.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> (No tested the
Link: https://lore.kernel.org/r/20191128083718.39177-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the driver actually support looking up GPIO
descriptor. A coding mistake in the initial descriptor
support patch was that it was failing to turn on the very
feature it was implementing. Mea culpa.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch reverts commit 6e0a32d6f3 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit f3186dd876 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To fix a regression on the Cadence SPI driver, this patch reverts
commit 6046f5407f ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit 3e5ec1db8b ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
LPSS SPI on Intel Jasper Lake is compatible with Intel Ice Lake which
follows Intel Cannon Lake. Add PCI IDs of Jasper Lake.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191125125159.15404-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no reason to use the dma_request_slave_channel_compat() as no
filter function and parameter is provided.
Switch the driver to use dma_request_chan() instead and add support for
deferred probing against DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191121092703.30465-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133916.13595-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118024848.21645-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-10-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-9-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-7-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl_spi_cpm_free() function does not make the same
checks as the error path in fsl_spi_cpm_init() leading
to crashes on error.
Cc: Fabio Estevam <festevam@gmail.com>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191113014442.12100-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit d948e6ca18 ("spi: add power control when set_cs") added generic
runtime PM handling, but also changed the return value to be 1 instead
of 0 that we had earlier as pm_runtime_get functions return a positve
value on success.
This causes SPI devices to return errors for cases where they do:
ret = spi_setup(spi);
if (ret)
return ret;
As in many cases the SPI devices do not check for if (ret < 0).
Let's fix this by setting the status to 0 on succeess after the
runtime PM calls. Let's not return 0 at the end of the function
as this might break again later on if the function changes and
starts returning status again.
Fixes: d948e6ca18 ("spi: add power control when set_cs")
Cc: Luhua Xu <luhua.xu@mediatek.com>
Cc: wsd_upstream@mediatek.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20191111195334.44833-1-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.
Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver forgets to unregister controller when remove.
Use devm API to unregister it automatically to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109075517.29988-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both omap2_mcspi_tx_dma() and omap2_mcspi_rx_dma() are only called from
omap2_mcspi_txrx_dma() and omap2_mcspi_txrx_dma() is always called after
making sure that mcspi_dma->dma_rx and mcspi_dma->dma_tx are not NULL
(see omap2_mcspi_transfer_one()).
Therefore remove redundant NULL checks for omap2_mcspi->dma_tx and
omap2_mcspi->dma_rx pointers in omap2_mcspi_tx_dma() and
omap2_mcspi_rx_dma() respectively.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191109041827.26934-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.
In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).
Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.
As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.
Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Using masks makes sense when manipulating fields of several bits. When
only one bit is involved, it is usual to just use the BIT() macro but
in this case using the term mask is abusive. Fix the #define macros
and their comments.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-5-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the bits/bitfields #define'd in this driver are composed with:
1/ the driver prefix
2/ the name of the register they apply to
Keep the naming consistent by applying this rule to the CONFIG register
internals. These definitions will be used in a following change set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike what the driver is currently advertizing, CS0 only can be used,
CS1 is not supported at all. Prevent people to use CS1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In this driver (and also in a lot of other drivers in drivers/spi/),
the spi_controller structure is sometimes referred as 'ctlr' and
sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more
common so keep the naming consistent in this driver and s/ctrl/ctlr/.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108105920.19014-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Devices with chip selects driven via GPIO are not compatible with the
spi-mem operations. Fallback to using standard spi transfers when the
device is connected with a gpio CS.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI_LOOP is set in spi->mode but not propagated to the register.
A previous patch removed the bit during a cleanup.
Fixes: e1bc204894 ("spi: dw: fix potential variable assignment error")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Link: https://lore.kernel.org/r/1572985330-5525-1-git-send-email-thor.thayer@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver forgets to disable and unprepare clk when probe fails and
remove.
Add the calls to fix the problem.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Palmer Dabbelt <palmer@dabbelt.com>
Link: https://lore.kernel.org/r/20191101121745.13413-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the TXX9 SPI driver to use GPIO descriptors
to control the GPIO chip selects.
As the driver was clearly (ab)using the device tree "reg"
property to offset into the global GPIO chip we have to
add a hack to counter the hack: add a 1-to-1 chip select
to GPIO offset mapping for all 16 lines on the TXX9 GPIO
chip. The details are described in a largeish comment
in the patch.
We do not need to set up the GPIO as output any more since
the core will take care of this, as well as it will handle
the polarity inversion semantics.
Cc: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073832.24038-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Committed version of the commit b9fc2d207e ("spi: dw: Move runtime PM
enable/disable from common to platform driver part") does not include by
some reason changes to drivers/spi/spi-dw.c that were part of the original
patch sent to the mailing list.
Complete the code move by doing those changes now.
Fixes: b9fc2d207e ("spi: dw: Move runtime PM enable/disable from common to platform driver part")
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191030113137.15459-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When rebooting system, the PMIC watchdog time loading may not be loaded
correctly when another system is feeding the PMIC watchdog, since we did
not check the watchdog busy status before loading time values.
Thus we should set the BIT_WDG_NEW bit before loading time values, that
can support multiple loads without checking busy status to make sure the
time values can be loaded successfully to avoid this potential issue.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/5655318a7252c9ea518c2f7950a61228ab8f42bf.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if the flag use_gpio_descriptors is set, it is possible that
cs_gpiods was not allocated, which leads to a kernel crash.
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Fixes: 3e5ec1db8b ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191024141309.22434-1-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The current conditional for PCI ID matching is hard to read.
Introduce couple of temporary variables to increase readability
of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191021103625.4250-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This core supports either 8, 16 or 32 bits as word width. This value is only
settable on instantiation, and thus we need to support any of them by means
of the device tree.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-3-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The devm_ioremap_resource() has already a check for resource pointer
being NULL. No need to double check this.
Drop extra check of platform_get_resource() returned value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191021103625.4250-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel(R) Programmable Services Engine (Intel(R) PSE) SPI controllers in
Intel Elkhart Lake have two Chip Select signals instead of one.
Reported-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-3-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean