imx7d (and imx8mm, imx8mn) uses Samsung PHY and USB generic PHY driver.
The USB generic PHY driver is impossible to have a charger detection
for every user, so we implement USB charger detection routine at glue
layer. After the detection has finished, it will notify USB PHY
charger framework, and the uevents will be triggered.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If ID or VBUS is from external block, don't enable its wakeup
because it isn't used at all.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds support to set the power line polarity for i.MX SoCs.
To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.
Also make use of of_property_read_bool.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
To support imx HSIC, there are some special requirement:
- The HSIC pad is 1.2v, it may need to supply from external
- The data/strobe pin needs to be pulled down first, and after
host mode is initialized, the strobe pin needs to be pulled up
- During the USB suspend/resume, special setting is needed
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use ULPI phy with usb host 2 and 3, we need to configure
controller register to enable ULPI features.
Each USB controller have different behaviour, so in order to avoid to have
several "swicth(data->index)" and lock/unlock, we prefer to get the index
switch and then test for features if they exist for this index.
This patch also remove useless test of reg and val. Those two values cannot
be NULL.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx usb over current polarity is low active by default, with
over-current-active-high property added, user can config it to be high
active. Meanwhile keep this setting unchanged for existing platforms
so new platform must set the right value for active low by its usbmisc
init function if over current is enabled.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This API is used to enable/disable usb wakeup, only imx6 series are
added, since I don't have other imx hardware on hand. Other imx users
can add their API according to reference manual after testing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds Vybrid VF610 SoC support. The IP is very similar to i.MX6,
however, the non-core registers are spread in two different register
areas. Hence we support multiple instances of the USB misc driver
and add the driver instance to the imx_usbmisc_data structure.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chipidea i.MX driver is split into two drivers. The ci_hdrc_imx driver
handles the chipidea cores and the usbmisc_imx driver handles the noncore
registers common to all chipidea cores (but SoC specific). Current flow is:
- usbmisc sets an ops pointer in the ci_hdrc_imx driver during probe
- ci_hdrc_imx checks if the pointer is valid during probe, if yes calls
the functions in the ops pointer.
- usbmisc_imx calls back into the ci_hdrc_imx driver to get additional
data
This is overly complicated and has problems if the drivers are compiled
as modules. In this case the usbmisc_imx driver can be unloaded even if
the ci_hdrc_imx driver still needs usbmisc functionality.
This patch changes this by letting the ci_hdrc_imx driver calling functions
from the usbmisc_imx driver. This way the symbol resolving during module
load makes sure the ci_hdrc_imx driver depends on the usbmisc_imx driver.
Also instead of letting the usbmisc_imx driver call back into the ci_hdrc_imx
driver, pass the needed data in the first place.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"ci13xxx" is bad for at least the following reasons:
* people often mistype it
* it doesn't add any informational value to the names it's used in
* it needlessly attracts mail filters
This patch replaces it with "ci_hdrc", "ci_udc" or "ci_hw", depending
on the situation. Modules with ci13xxx prefix are also renamed accordingly
and aliases are added for compatibility. Otherwise, no functional changes.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jun Li