The time to suspend a single codec may be several hundreds of ms. When runtime
power saving is disabled, driver suspend time can be long especially when there
are more than one codec on the bus.
To reduce driver suspend time, this patch creates a work queue for the bus, and
suspends the codecs in parallel if there are multiple codecs on the bus.
[fixed cosmetic issues by tiwai]
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Most Thinkpad Edge series laptops use conexant codec, so far although
the codecs have different minor Vendor Id and minor Subsystem Id,
they all belong to the cxt5066 family, this change can make the
mute/mic-mute LEDs support more generic among cxt_5066 family.
This design refers to the similar solution for the realtek codec
ALC269 family in the patch_realtek.c.
Cc: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to Mengdong, we shouldn't enable runtime PM when a codec
doesn't support EPSS, based on the experiences on Windows.
We have already this check in HDMI codec drivers, but now apply it in
general in hda_codec.c.
Credit goes to Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now we fixed the long-standing bugs of runtime PM, let's enable
Panther Point again. The runtime PM was disabled in the HDMI codec
driver due to the S3 issue, and this should have been fixed now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
No functional change.
- codec->pm_down_notified flag is renamed to codec->pm_up_notified
flag (and takes the reversed meaning), which is managed solely in
hda_call_pm_notify() now.
- The explicit call of hda_call_pm_notify() is moved into
hda_keep_power_on().
- Removed a redundant call of hda_call_pm_notify() in
snd_hda_power_up(), as it's called in hda_call_codec_resume()
anyway.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a codec contains only the digital outputs, it's very likely a
HDMI/DP codec, which isn't supported by the generic parser but via
HDMI codec parser code. Detect such a case and bind with the proper
parser object if available.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Drop the hard dependency on the generic parser code and load / unload
the generic parser code dynamically if built as a module. This allows
us to avoid the generic parser if only HDMI/DP codecs are found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use bus->power_keep_link_on instead. The controller shouldn't go to
D3 when the link isn't reset, so essentially avoiding the link reset
means avoiding the runtime PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set the missing pcbeep default amp for ALC668.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
current_headset_type should be of the HEADSET_TYPE enum, not the
HEADSET_MODE enum. Since ALC_HEADSET_TYPE_UNKNOWN and ALC_HEADSET_MODE_UNKNOWN
are both 0, this patch is just janitorial.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models (or maybe depending on BIOS version) of Sony VAIO with
ALC260 give no proper pin configurations as default, resulting in the
non-working speaker, etc. Just provide the whole pin configurations
via a fixup.
Reported-by: Matthew Markus <mmarkus@hearit.co>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The laptop has a built-in speaker on NID 0x1a. It's an LFE only on
the right channel, so we need to provide an explicit chmap, too.
There might be other surround speakers, but they can fixed in addition
at later point, so let's fix the easier bass speaker at first.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65091
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec is resumed, it keeps the power on while the resuming
phase via hda_keep_power_on(), then turns down via
snd_hda_power_down(). At that point, snd_hda_power_down() notifies
the power down to the controller, and this may confuse the refcount if
the codec was already powered up before the resume.
In the end result, the controller goes to runtime suspend even before
the codec is kicked off to the power save, and the communication
stalls happens.
The fix is to add the power-up notification together with
hda_keep_power_on(), and clears the flag appropriately.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
You're looking at a casual headset patch,
for a specific hardware it will match,
and suddenly, the headset jack will work,
so please apply this simple quirk!
BugLink: https://bugs.launchpad.net/bugs/1253038
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and load from the external firmware files.
The firmware binary blobs in cs46xx driver have been in a gray zone
regarding the license. It's most likely should be OK, but still
unclear. And, the size isn't that small, too.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=10750
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station is a Thinkpad thing, so it makes sense to check
for mute/micmute LEDs for that quirk type too.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We're using the ACPI interface to detect whether we're dealing with a Thinkpad
or not. This way we're not loading the thinkpad_acpi module when we're not on
a Thinkpad, but at the same time, we give the opportunity to check for, and
potentially enable, both present and future Thinkpad with mute/micmute LEDs.
At least those running the ALC269 family (269 to 299) of Realtek codecs.
Cc: Alex Hung <alex.hung@canonical.com>
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_codec_reset() is called either in resetting the whole setup at
error paths or hwdep clear/reconfig sysfs triggers. But all of these
don't assume that the power has to be off, rather they want to keep
the power state unchanged (e.g. reconfig_codec() calls the power
up/down by itself). Thus, unconditionally clearing the power state in
snd_hda_codec_reset() leads to the inconsistency, confuses the further
operation. This patch gets rid of the lines doing that bad thing.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Similarly as other laptops with AD1981 & co codecs, we can control
EAPD on AD1986A more safely depending on the Master switch, in order
to save some power.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only EAPD on AD1986A is on NID 0x1b where usually the speaker.
But this doesn't control only the speaker amp but may influence on all
outputs, e.g. Lenovo N100 laptop seems to have this issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We don't change the EAPD bit in set_pin_eapd() if keep_eapd_on flag is
set by the codec driver and enable is false. But, we also apply the
flipping of enable value according to inv_eapd flag in the same
function, and this confused the former check, handled as if it's
turned ON. The inverted EAPD check must be applied after keep_eapd_on
check, instead.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In case there is both a multifunction headset jack and a Line Out
jack, automuting was not working properly from the Line Out jack.
This patch fixes that issue.
Cc: stable@vger.kernel.org (3.10+)
BugLink: https://bugs.launchpad.net/bugs/1250377
Tested-by: Cyrus Lien <cyrus.lien@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to the HDA specification the baseline ELD length is counted in
DW of 4 bytes instead of in bytes.
Fix the code accordingly.
Baseline length is not used by the kernel so only the ELD exported to
userspace was affected. No issues have been reported.
v2: Fixed so that eld_size is adjusted upwards accordingly as well.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ATI/AMD video/audio latencies are specified in apparent HDMI VSDB
format. In this format values above 251 are not valid (or stream
component is not supported - 255), but no checking is performed since
this was not mentioned in the AMD HDA verbs specification.
Check that the latencies are valid before using them, and add a comment
describing the formats.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add error checks to HBR status reads (both generic and ATI/AMD) and
ATI/AMD codec reads for ELD generation.
Unchecked errors in these just caused more errors later on (invalid
codec writes for the HBR ones and ELD parsing errors for the ATI/AMD ELD
ones), but it is better to catch them earlier.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Channel map positions FLH, FCH, FRH duplicate positions TFL, TFC, TFR.
Both are the speakers above the front speakers (CEA uses "high" and USB
audio uses "top" nomenclature).
Since the USB audio code has used the TFx positions since v3.8
(04324ccc75, "ALSA: usb-audio: add channel map support") but the HDMI
code only just started using FxH in a5b7d510b2 ("ALSA: hda -
hdmi: Fix channel maps with less common speakers") which is not yet in
any released kernel, standardize on TFx instead.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The SPDIF output MBP11,2 requires the pin control to be set/cleared
for turning on/off the optical SPDIF. The red light turns off only
when the corresponding pin control is cleared (or powered to D3).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New codec ALC255/ALC3234 support multifunction jacks.
It used for menual select the input device.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [8fe7b65ab465: ALSA: hda - Apply GPIO setup for MacBooks
with CS4208] added a fixup entry matching with the vendor id 0x106b.
This broke the fixups for previous MBA6,1 and 6,2, since the PCI SSID
vendor id matches before evaluating the codec SSIDs.
We had a similar issue on Mac with Sigmatel codecs, and solve this
problem again similarly, by introducing a skeleton entry matching with
the all MacBooks, then remap to the right one.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Fixes: 8fe7b65ab4 ('ALSA: hda - Apply GPIO setup for MacBooks with CS4208')
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upon suspend / resume, the fixup register settings are lost because
sending HDA_FIXUP_ACT_PRE_PROBE is not part of the resume path. Instead,
write our registers in response to the HDA_FIXUP_ACT_INIT, which happens
after initial probe and upon resume.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dmesg here has a 100+ consecutive lines of:
[ 1464.219446] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219451] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219454] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
...
Ratelimit the message to reduce the dmesg log noise.
Coalesce the format while at it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent fake ELD patches, we can remove the check for AMD
HDMI in hdmi_present_sense() and decide the return value from
eld_valid value.
Suggested by Anssi Hannula.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just added a missing ifdef:
sound/pci/ice1712/quartet.c:210:14: warning: 'get_binary' defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes a race condition in case several monitors are being
repolled in parallel.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the jack should not be reported to userspace (e g, because it is
in some transitional state), one can set this flag.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a small gap between the jack detection unsolicited event and
the time the ELD is updated. When user-space queries the HDMI ELD
immediately after receiving the notification, it might fail because of
this gap.
For avoiding such a problem, this patch tries to delay the HDMI jack
detect notification until ELD information is fully updated. The
workaround is imperfect, but good enough as a starting point.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine has a multi-function headset jack.
BugLink: https://bugs.launchpad.net/bugs/1248856
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on ASUS W5A laptop with ALC880 codec doesn't provide any pin
configurations, so we have to set up all pins manually.
Reported-and-tested-by: nb <nb@dagami.org>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a superset of the existing CX2075x codecs, so we can reuse the
existing parser code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The warnings are really harmless but annoying. Since they are only
about debug prints, and it's at most 32bit DMA, let's just cast to
unsigned long.
sound/pci/lx6464es/lx6464es.c:457:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
sound/pci/lx6464es/lx_core.c:1195:21: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine has a mute LED as well as a noisy internal mic. Hence it needs
quirks for both limiting the mic boost as well as enabling the LED.
BugLink: https://bugs.launchpad.net/bugs/1248476
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HP machines with Realtek codecs have mute LEDs connected to VREF pins.
However when these go into runtime suspend, the pin powers down and its
pin control is disabled, thus disabling the LED too.
This patch fixes that issue by making sure that the pin stays in D0 with
correct pin control.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1248465
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BUG_ON() is rather useless for debugging as it leads to panic().
Use WARN_ON() and handle the error cases accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The playback chmap for multi-channel stream hasn't been properly added
to intel8x0 devices due to the wrong condition.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"HDA Intel MID" is no correct name for Haswell HDMI controllers.
Give them a better name, "HDA Intel HDMI".
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell HDMI audio controllers seem to get stuck when unaligned buffer
size is used. Let's enable the buffer alignment for the corresponding
entries.
Since AZX_DCAPS_INTEL_PCH contains AZX_DCAPS_BUFSIZE that disables the
buffer alignment forcibly, define AZX_DCAPS_INTEL_HASWELL and put the
necessary AZX_DCAPS bits there.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60769
Reported-by: Alexander E. Patrakov <patrakov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Same as we already have for Conexant. Right now it's only enabled
for one machine.
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device IDs of the AMD Cypress/Juniper/Redwood/Cedar/Cayman/Antilles/
Barts/Turks/Caicos HDMI HDA controllers weren't added explicitly
because the generic entry works, but it made the device appearing as
"Generic", and people are confused as if it's no proper HDMI
controller. Add them so that the name shows up properly as "ATI HDMI"
instead of "Generic".
According to Takashi's tests and the lack of complaints, these devices
work fine without disabling snooping.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a bitmask to hda_gen_spec indicating NIDs to exclude from the
possible volume controls. That is, when the bit is set, the NID
corresponding to the bit won't be picked as an output volume control
any longer.
Basically this is just a band-aid for working around the issue found
with CS4208 codec, where only the headphone pin has a volume AMP with
different dB steps.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the TLV db scale result before actually dividing in vmaster
slave init code. Also mask TLV_DB_SCALE_MUTE bit so that the right
value is obtained even if this bit is set by the codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on Acer TravelMate 6293 doesn't set up the SPDIF output pin
correctly as default, so enable it via a fixup entry.
Reported-and-tested-by: Hagen Heiduck <heiduck.suse@fmail.postpro.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function name not_share_unassigned_cvt() is opposite to what it does.
This patch renames it to intel_not_share_assigned_cvt(), and addes comments
to explain why some Intel display codecs need this workaround.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NVIDIA HDMI codecs do not seem to follow the Audio Sample Packet (ASP)
channel mapping (as set by verb F32h per HDA specification 7.3.3.41)
when playing back 2-channel audio (CEA CA 0x00).
Basically this means that specifying swapped channels for stereo audio
(FR,FL) does not take effect, and e.g. this command plays back on the
wrong channel:
speaker-test -c2 -Dhdmi:CARD=NVidia,DEV=0 -m FR,FL -s1
Multichannel audio is not affected.
This issue has been confirmed to exist on codec 0x10de0015 by me and on
0x10de0040 by Juho Teperi.
Disable 2ch FL/FR channel swapping on all NVIDIA HDMI codecs that use
the standard HDA channel mapping system. Since this is a very minor
functionality loss, we err on the side of disabling it for newer codecs
as well until any future testing confirms that this issue has been
fixed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Helped-by: Juho Teperi <juho.teperi@iki.fi>
Cc: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Valleyview display codec, if an unused pin chooses an assgined converter
selected by a used pin, playback on the unused pin can also give sound to the
output device of the used pin. It's because data flows from the same convertor
to the display port of the used pin. This issue is same as Haswell.
So this patch avoids using assinged convertors for unused pins.
The related function haswell_config_cvts() is renamed for code reuse.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N56VZ and N76VZ laptops have a bass speaker but its output comes
only from the right channel. This patch adds the extra chmap specific
to these models.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=846531
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N76VZ needs the same fixup as N56VZ for supporting the boost
speaker.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=846529
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC283-based Chromebook suffers from occasional white noise, and it
turned out that this comes from AA-loopback. Disable this output path
by just clearing mixer_nid, then the generic parser will skip the
creation of AA-loopback path.
Reported-and-tested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The FUNCTION_TYPE parameter isn't associated with any NID, thus
showing the uninitialized nid in the error message is simply
nonsense.
Spotted by coverity CID 145068.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just pass the error code returned from copy_from_user_toio() and
copy_to_user_fromio() helpers.
Spotted by coverity CID 114119.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable runtime is never used, and this might be even a source of
NULL-dereference. Nothing better than killing it.
Spotted by coverity CID 100862.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a possible NULL access of indexp in fill_audio_out_name() called
from snd_hda_get_pin_label().
Spotted by coverity CID 402035.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As EAPD on NID 0x12 (speaker pin) is used as the master amp on
Thinkpads with AD1984A codec, we can hook this to vmaster for saving a
bit more power at master mute state.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1984A codec has a couple of pins with EAPD controls, and the generic
codec driver tries to turn each of them on/off depending on the pin
active state. However, Thinkpads seem to use EAPD of the speaker pin
as a master EAPD for controlling the mute of all outputs, including
the headphone. This results in the dead headphone output via the
headphone plugging because it mutes the speaker and turns off EAPD.
The fix is to simply add spec->gen.keep_on_eapd flag.
[This is a regression fix on 3.12 where we moved the AD codec parser
to the generic parser. 3.11 and earlier didn't show this problem
because still static quirks have been used.]
Reported-and-tested-by: Vito Caputo <vcaputo@gnugeneration.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The generic parser has a support of vmaster hook, but this is
initialized only in the init callback with the check of the presence
of the corresponding kctl. However, since kctl is NULL at the very
first init callback that is called before build_controls callback, the
vmaster hook sync is skipped there. Eventually this leads to the
uninitialized state depending on the hook implementation.
This patch adds a simple workaround, just calling the sync function
explicitly at build_controls callback.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of the
DMA controller which removes some guesswork and magic numbers fromm
drivers.
- A refresh of the documentation.
- Conversions of many drivers to direct regmap API usage in order to
allow the ASoC level register I/O code to be removed, this will
hopefully be completed by v3.14.
- Support for using async register I/O in DAPM, reducing the time taken
to implement power transitions on systems that support it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=rVsK
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.13
- Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of the
DMA controller which removes some guesswork and magic numbers fromm
drivers.
- A refresh of the documentation.
- Conversions of many drivers to direct regmap API usage in order to
allow the ASoC level register I/O code to be removed, this will
hopefully be completed by v3.14.
- Support for using async register I/O in DAPM, reducing the time taken
to implement power transitions on systems that support it.
hdmi_setup_audio_infoframe() does not set up pin and infoframe if there
is no connected sink. If a sink is connected while audio playback is
already in progress, the pin and infoframe will not be properly set up,
causing no audio or wrongly mapped audio.
On Intel Haswell codecs the hdmi_setup_audio_infoframe() is already
called again from hdmi_present_sense() when an ELD appears because
transcoder:port mapping may have changed.
Make the call non-Haswell-specific so that audio will be properly set up
if the playback was started before a sink was connected.
Tested on non-Haswell Intel HDMI codec by plugging sink in during
playback.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent AMD HDMI codecs (revision ID 3 and later, 0x100300 as reported by
procfs codec#0) have a configurable ramp-up/down functionality.
The documentation ( http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf )
specifies that 180 ("180/256 =~ 0.7") is recommended for PCM and 0 for
non-PCM.
Apply the recommended values according to provided S/PDIF AES0 settings
since ramp-up/down does not make sense for non-PCM.
v2: adapted to hdmi_ops infrastructure
* More note from Anssi:
actually, re-reading mails reveals that Olivier didn't find the
expected difference with this setting, except for "maybe slightly
slower startup with AES0=6" (i.e. value 0, which is unexpected).
So maybe
a) it makes too unnoticiable a difference, or
b) only affects certain hardware (card and/or sink), or
c) ramp-up/down is only triggered with the MUTE bit of
ATI_VERB_SET_MULTICHANNEL_xx which is also rev3+ specific,
but is not presently used by the driver,
or something else.
So there's a significant chance setting ramp rate is useless for us ATM,
but probably does not do actual harm either.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Olivier Langlois <olivier@trillion01.com> # v1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD HDMI codecs do not include standard HDA HDMI HBR support (which
is required for bitstreaming DTS-HD and Dolby TrueHD), instead they have
custom verbs for checking and enabling it.
Add support for the ATI/AMD HDMI HBR verbs.
The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
v2: adapted to hdmi_ops infrastructure
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD HDMI/DP codecs do not include standard HDA ELD (EDID-like data)
support.
In place of providing access to an ELD buffer, various vendor-specific
verbs are provided to provide the relevant information. Revision ID 3
and later (0x100300 as reported by procfs codec#X) have support for
providing more information than the previous revisions (but only if
supported by the display driver).
Generate ELD from the information provided by the vendor-specific verbs
on ATI/AMD codecs.
The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
v2: moved code to hda_eld.c and cleaned it up
v3: adapted to hdmi_ops infrastructure
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD codecs do not support all the standard HDA HDMI/DP functions,
instead various vendor-specific verbs are provided.
This commit addresses these missing functions:
- standard channel mapping support
- standard infoframe configuration support
ATI/AMD provides their own verbs that allow the following:
- setting CA for infoframe
- setting down-mix information for infoframe
- channel pair remapping
- individual channel remapping (revision ID 3+, 0x100300+)
The documentation for the verbs has now been released by AMD:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
Add support for the ATI/AMD specific verbs and use them instead of the
generic methods on ATI/AMD codecs. This allows multi-channel PCM audio
to work.
Channel remapping is restricted to pairwise mapping on codecs with
revision ID 2 (0x100200 as reported by procfs codec#X) or lower. This
means cards up to Radeon HD7670 as far as I know. This will not affect
standard multi-channel modes since these codecs support automatic
FC-LFE swapping for HDMI.
ATI/AMD codecs do not advertise all of their supported rates, formats
and channel counts, therefore that information is forced accordingly so
that all HDMI 1.x PCM parameters are marked as supported.
Support for multiple ports is also added to patch_atihdmi so that
0x1002aa01 codecs with multiple ports will work properly when switched
back to that patch.
v2: splitted ELD emulation to a separate patch, tlv fixes
v3: adapted to the new hdmi_ops infrastructure, fixed rev3+ vendor id
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2+rev3fix
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upcoming AMD multichannel support requires many customized operations
(channel mapping, ELD, HBR) but can otherwise share most of its code
with the generic patch.
Add a local struct hdmi_ops containing customizable HDMI-specific
callbacks and move the current code to those callbacks. Functionality is
unaltered.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machine with 85ms delay might be happen pop noise when codec
enter to D3. Raise up to 100ms delay will be match for more machine.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When HP laptops with mute and mic-record LEDs go to runtime suspend,
these LEDs are turned on forcibly no matter whether GPIO pis are on or
off. This strange behavior seems triggered by resetting the HD-audio
bus link at azx_rutime_suspend(). So, just add a new hda_bus flag to
avoid the link reset at runtime suspend and set it for these HP
machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's just another variant of ALC269 & co.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Emitting an OOM message isn't necessary after input_allocate_device
as there's a generic OOM and a dump_stack already done.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a machine goes to S3/S4 after power-save is enabled, the runtime
PM refcount might be incorrectly decreased because the power-down
triggered soon after resume assumes that the controller was already
powered up, and issues the pm_notify down.
This patch fixes the incorrect pm_notify call simply by checking the
current value properly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... which was introduced by the previous commit a4e9a38b, causing
build errors without CONFIG_PROC_FS.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862882) and module alias for
Valleyview2 display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Partially restructures _snd_emu10k1_audigy_init_efx() and
_snd_emu10k1_init_efx() functions.
Be noted that the cast is demanded to use '__user'. So, in these cases,
avoid patches based on the coccinelle 'drop_kmalloc_cast' semantic patch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the lock is used primarily in patch_hdmi.c, it's better to move
it in the local struct instead of exporting in hda_eld. The only
functions requiring the lock in hda_eld.c are proc accessors. So in
this patch, the proc entry and its creation/deletion/accessors are
moved into patch_hdmi.c, together with the mutex lock to pin_spec
struct.
The former proc info functions are exported so that they can be called
from patch_hdmi.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some per_pin fields and ELD contents might be changed dynamically in
multiple ways where the concurrent accesses are still opened in the
current code. This patch fixes such possible races by using eld->lock
in appropriate places.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The zero-length connection list happens so often on Haswell HDMI, and
it results in warning messages like
ALSA: hda_codec: invalid CONNECT_LIST verb 5[1]:0
at each time the codec resumes from the power-save, which is fairly
annoying.
Since this is no real error, make it shown only in the verbose debug
mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A fixup which should be called before codec being freed will come
to use in the next patch.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In GCC the sizeof(hdsp_version) is 8 because there is a 2 byte hole at
the end of the struct after ->firmware_rev.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The create_bind_cap_vol_ctl does not create any control indicating
that an inverted dmic is present. Therefore, create multiple
capture volumes in this scenario, so we always have some indication
that the internal mic is inverted.
This happens on the Lenovo Ideapad U310 as well as the Lenovo Yoga 13
(both are based on the CX20590 codec), but the fix is generic and
could be needed for other codecs/machines too.
Thanks to Szymon Acedański for the pointer and a draft patch.
BugLink: https://bugs.launchpad.net/bugs/1239392
BugLink: https://bugs.launchpad.net/bugs/1227491
Reported-by: Szymon Acedański <accek@mimuw.edu.pl>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using the headset mic model will cause the headset mic to be labeled
"headset mic" instead of just "mic".
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The external mic showed up with a precense detect of "always present",
essentially disabling the internal mic. Therefore turn off presence
detection for this pin.
Note: The external mic seems not yet working, but an internal mic is
certainly better than no mic at all.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1227093
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the case where we have both line out and more than stereo speakers,
the speaker DACs will end up in extra_out_nid.
In fact, AFAIU, speakers are the only ones that can end up in extra_out_nid,
and if we have several of those, they should be surround outputs
rather than copy front.
BugLink: https://bugs.launchpad.net/bugs/1236965
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N56VZ needs a fixup for the bass speaker pin, which was already
provided via model=asus-mode4.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=841645
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently hdmi_setup_audio_infoframe() reprograms the HDA channel
mapping only when the infoframe is not up-to-date or the non-PCM flag
has changed.
However, when just the channel map has been changed, the infoframe may
still be up-to-date and non-PCM flag may not have changed, so the new
channel map is not actually programmed into the HDA codec.
Notably, this failing case is also always triggered when the device is
already in a prepared state and a new channel map is configured while
changing only the channel positions (for example, plain
"speaker-test -c2 -m FR,FL").
Fix that by always programming the channel map in
hdmi_setup_audio_infoframe(). Tested on Intel HDMI.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow channel map debugging for both automatic and manual channel maps,
and print CA always when updating infoframe.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the available channel maps TLV only contains channel maps that
are limited to the traditional 7.1 speakers.
Since the other HDMI channel mapping functions have been fixed to
properly handle all CEA-861-E specified speakers, allow them to be
listed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For some speakers and slots the CEA slot <-> speaker assignment depends
on the used CEA Channel Allocation value.
Therefore the from_cea_slot() and to_cea_slot() helpers currently only
work correctly for the regular 7.1 speakers.
Fix them to work with all speakers, taking the re-ordered CA index as
input and adapting use sites accordingly.
This change allows manual channel mapping to actually work for all CEA
allocated speakers. Additionally, this fixes incorrect channel map
reporting in automatic channel mapping mode when an affected speaker
position is used (e.g. 6.1 map which contains an RC speaker).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_manual_setup_channel_mapping() and hdmi_std_setup_channel_mapping
try to assign ALSA channels to HDMI channel slots and disable (i.e.
silence) other slots.
However, they try to disable a slot by using AC_VERB_SET_CHAN_SLOT with
parameter ((alsa_ch << 8) | 0xf), while the correct parameter is
((0xf << 8) | hdmi_slot), i.e. the slot should be unassigned, not the
ALSA channel.
Fix that by actually disabling the unused slots.
Note that this bug did not cause any (reported) issues because slots
incorrectly having audio are normally ignored by a receiver if the CEA
channel allocation used does not map that slot to any speaker.
Additionally, the converter channel count configuration limits the
number of actually active channels in any case.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the converter channel count is set to the number of actual
input channels. The audio infoframe channel count field is set
similarly.
However, sometimes the used channel map does not map all input channels
to outputs. Notably, 3 channel modes (e.g. 2.1) require a dummy input
channel so there are 4 input channels. According to the HDA
specification, converter channel count should be programmed according to
the number of _active_ channels.
On Intel HDMI codecs (but not on NVIDIA), setting the converter channel
to a higher value than there are actually mapped channels to HDMI slots
will cause no audio to be output at all.
Note that the effects of this issue are currently partially masked by
other bugs that prevent the driver from actually unmapping channels in
certain cases. For example, if a 4 channel stream is first created and
prepared, it gets a FL,FR,RL,RR mapping (ALSA->HDMI slot mapping 0->0,
1->1, 2->4, 3->5). If one thereafter assigns a FR,FL,FC mapping to it,
the driver will remap 2->3 but fail to unmap 2->4 and 3->5, so there are
still 4 active channels and the issue will not trigger in this case.
These bugs will be fixed separately.
Fix the channel counts in the converter channel count field and in the
audio infoframe channel count field to match the actual number of active
channels.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_std_setup_channel_mapping() selects a Channel Allocation according
to the sink reported speaker mask, preferring the ALSA standard layouts.
If the channel allocation is not one of the ALSA standard layouts, the
ALSA channels are mapped directly to HDMI channels in order. However,
the function does not take into account that there a holes in the HDMI
channel map.
Additionally, the function tries to disable a slot by using
AC_VERB_SET_CHAN_SLOT with parameter ((alsa_ch << 8) | 0xf), while the
correct parameter is ((0xf << 8) | hdmi_slot), i.e. the slot should be
unassigned, not the ALSA channel.
Fix both of the issues for non-ALSA-default layouts.
Tested on Intel HDMI with a speaker mask of FL | FR | FC | RC, which
causes CA 0x06 to be selected for 4-channel audio, which causes
incorrect output (sound destined to RC goes to FC and FC goes nowhere)
without the patch.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_setup_fake_chmap() is supposed to set the reported channel map when
the channel map is not specified by the user.
However, the function indexes channel_allocations[] with a wrong value
and extracts the wrong nibble from hdmi_channel_mapping[], causing wrong
channel maps to be shown.
Fix those issues.
Tested on Intel HDMI to correctly generate various channel maps, for
example 3,4,14,15,7,8,5,6 (instead of incorrect 3,4,8,7,5,6,14,0) for
standard 7.1 channel audio. (Note that the side and rear channels are
reported as RL/RR and RLC/RRC, respectively, as per the CEA-861
standard, instead of the more traditional SL/SR and RL/RR.)
Note that this only fixes the layouts that only contain traditional 7.1
speakers (2.0, 2.1, 4.0, 5.1, 7.1, etc.). E.g. the rear center of 6.1
is still being shown wrongly due to an issue with from_cea_slot()
which will be fixed in a later patch.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On this machine, DAC on node 0x03 seems to give mono output.
Also, it needs additional patches for headset mic support.
It supports CTIA style headsets only.
Alsa-info available at the bug link below.
Cc: stable@kernel.org (v3.10+)
BugLink: https://bugs.launchpad.net/bugs/1236228
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire 3830TG seems requiring GPIO bit 0 as the primary mute
control. When a machine is booted after Windows 8, the GPIO pin is
turned off and it results in the silent output.
This patch adds the manual fixup of GPIO bit 0 for this model.
Reported-by: Christopher <DIDI2002@web.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add 0x54584e03 ID for TI TLV320AIC27 AC'97 codec according to datasheet:
http://www.ti.com/lit/ds/slas253a/slas253a.pdf
The weird thing is that the chip is physically marked 320AD91.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More thorough testing showed that these verbs were necessary to
improve quality of the internal mic. Patch originally from Realtek.
BugLink: https://bugs.launchpad.net/bugs/1231931
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC283 pin control for Line1 default control by hidden register.
Use line1 as internal Mic will not get sound when boost value up.
Set control by verb for hidden register will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the default pin configuration and some init verbs for
setting COEFs, in addition to the correction of input pin AMP caps
for MacBook Air 6,1 and 6,2. With these changes, the headphone jack
detection starts working properly.
[trivial space fixes by tiwai]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Signed-off-by: Ben Whitten <benwhitten@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS can mark a pin as "no physical connection" if the port is used by an
integrated display which is not audio capable. And audio driver will overlook
such pins.
On Haswell, such a disconneted pin will keep muted and connected to the 1st
converter by default. But if the 1st convertor is assigned to a connected pin
for audio streaming. The muted disconnected pin can make the connected pin
no sound output.
So this patch avoids using assigned converters for all unused pins for Haswell,
including the disconected pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert 0 to false and 1 to true when assigning values to bool
variables. Inspired by commit 3db1cd5c05.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@@
bool b;
@@
(
-b = 0
+b = false
|
-b = 1
+b = true
)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'break' after a return statement is redundant. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'codec_send_command' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Local symbols used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These ->put() functions are called from snd_ctl_elem_write() with user
supplied data. snd_asihpi_tuner_band_put() is missing a limit check and
the check in snd_asihpi_clksrc_put() can underflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small fixes, nothing with any broad impact but all useful for the
affected systems. The Kirkwood compatible string change is fixing up a
string just added in the merge window so that we don't get any changes
in released kernels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSMEN7AAoJELSic+t+oim9fUcP/2/JSlEzCnf9mnIVu5JUb4o0
N9sqvZ3FuBmB2s+X7XdzHHatn/SRcj8bdPIUDyghsM+Ax6inzHCkLLxF0gMfgo1k
YmbVamD9x+Odj7ovs/M7/pRji9vBUFRmTdh6DnxIcQUGyuZRIMEIYxgnu//tXQ6+
vL2dJ3d3S37k4NtqHebKf1iL4ExGMAkp6f7Rig3YXc/N+jc8O/uUWAitfvBnzuBH
ZlFTCxkHhZ9mYi/xRBUSOFbb96bQnHN2KQ3soss1xDKhJVpjuo1rOWfTZE9c7bMY
OvqsMJDwaPNiCF0UzdCPQ1SMdE8r8U2lMMjyeQN76R9tqSVBtgxPeLvjzN0l3Xkf
mnHd1LZXGOF5cSfrA/Diy4leFk0A0pJQSxdDt54vlRcCG3aV7IRJOkPi4C0tMHQE
hkXOfgF6XERDsNV4RgzangAAvjKeXPqItWITZx+qtK7AxtCC6xpMc5EHV4wbFmTP
bYz6oKBehQy5gaI/z5Ad0mU1JK1vJH6n2ENtu/zNxBzfHIiyhF5fBPSuE+IGxvJf
/ANQf44DkkXLHZv5766lYUbldGmFYbiva2us+uDxaEfjSW5DDSSn/aYn73IsYJ16
L5MsX0s/J2o/i10kuXPlWMWIkoat1Y2vDUrdjg1xQ1IrkZRAZDnIYJz4yS8TwNyT
8rToadF2zYPKxwDVb37E
=oTEO
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.12
A few small fixes, nothing with any broad impact but all useful for the
affected systems. The Kirkwood compatible string change is fixing up a
string just added in the merge window so that we don't get any changes
in released kernels.
MacBook 6,1 and 6,2 have a CS4208 codec instead of CS4206/CS4207 on
the former models. Most of functions work fine as is, except for the
silent speaker output. After debugging sessions, it turned out that
the machine needs to set GPIO 0 for the speaker amp.
This patch adds the basic support for CS4208 and the fixup for these
MacBooks. Basically the codec works just with the generic parser.
For re-using the existing GPIO amp code and init/free callbacks, a few
places have been changed so that CS4206/4207-specific codes (errata,
etc) won't hit with CS4208.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Reported-and-tested-by: Ian Munsie <darkstarsword@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite C870 shows interrupt problems occasionally when
certain mixer controls like "Mic Switch" is toggled. This seems
worked around by not using MSI.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=833585
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
When Gfx driver reconnects a port and transcoder, the pin amplifier will
be muted. To enable sound, the pin amp need to be unmuted.
This patch
- moves pin amp unmuting from stream preparing to hdmi_setup_audio_infoframe().
So if port:transcoder reconnection happens during stream playback, the ELDV
unsol event can stil trigger pin's amp unmuting when re-setting up audio
info frame.
- remove reading pin amp status before unmuting for speed-up, since pin amp
should always be unmuted.
- rename haswell_verify_pin_D0() to haswell_verify_D0(), since the convertor
power state is also fixed here.
This patch is mostly based on suggestion of David Henningsson.
Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To apply Haswell specific fixings, this patch defines is_haswell() to check
whether a display audio codec is Haswell, to avoid explicitly checking Haswell
vendor ID everywhere.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS TX300 has a built-in speaker in the tablet part and in the dock
part, and the tablet speaker is supposed to be unused while the
machine is docked. The current HD-audio driver, however, doesn't
support the dock speaker, partly because BIOS doesn't set up the pin
for the corresponding output.
But, not only the missing pin config, also the missing unsol event
handling is another issue. Otherwise the automatic switching via
dock/undock won't work.
Through debugging sessions, we found out that the dock speaker pin is
NID 0x1b, and it generates an unsol event at docking/undocking, the
docking state can be inquired via the normal pin detection verb.
Also, it's turned out that GPIO 2 is needed as an amp. So, all
materials are ready to cook.
This patch provides the basic dock speaker support with TX300:
- The dock speaker is turned on/off via "Dock Speaker" mixer mute.
- The dock speaker is automatically muted when docked. This is
independently from the mixer mute switch, just like the headphone
auto-mute function.
The implementation is a bit tricky. Since we want to handle it as a
secondary speaker, we set it up a pin as a speaker with a jack
detection. Then, the fixup function registers the own unsol callback
for this pin because the standard automute can't handle the thing like
a "speaker jack". In the own automute hook, we apply the mute of the
tablet speaker in addition by checking the dock state.
Also, the speaker control names are slightly shuffled because the
generic parser doesn't give good names but blindly assumes a bass
speaker as a secondary speaker.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59791
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull media updates from Mauro Carvalho Chehab:
"This series contains:
- Exynos s5p-mfc driver got support for VP8 encoder
- Some SoC drivers gained support for asynchronous registration
(needed for DT)
- The RC subsystem gained support for RC activity LED;
- New drivers added: a video decoder(adv7842), a video encoder
(adv7511), a new GSPCA driver (stk1135) and support for Renesas
R-Car (vsp1)
- the first SDR kernel driver: mirics msi3101. Due to some troubles
with the driver, and because the API is still under discussion, it
will be merged at staging for 3.12. Need to rework on it
- usual new boards additions, fixes, cleanups and driver
improvements"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (242 commits)
[media] cx88: Fix regression: CX88_AUDIO_WM8775 can't be 0
[media] exynos4-is: Fix entity unregistration on error path
[media] exynos-gsc: Register v4l2 device
[media] exynos4-is: Fix fimc-lite bayer formats
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
[media] v4l: vsp1: Fix mutex double lock at streamon time
[media] v4l: vsp1: Add support for RT clock
[media] v4l: vsp1: Initialize media device bus_info field
[media] davinci: vpif_capture: fix error return code in vpif_probe()
[media] davinci: vpif_display: fix error return code in vpif_probe()
[media] MAINTAINERS: add entries for adv7511 and adv7842
...
Pull drm tree changes from Dave Airlie:
"This is the main drm pull request, I have some overlap with sound and
arm-soc, the sound patch is acked and may conflict based on -next
reports but should be a trivial fixup, which I'll leave to you!
Highlights:
- new drivers:
MSM driver from Rob Clark
- non-drm:
switcheroo and hdmi audio driver support for secondary GPU
poweroff, so drivers can use runtime PM to poweroff the GPUs. This
can save 5 or 6W on some optimus laptops.
- drm core:
combined GEM and TTM VMA manager
per-filp mmap permission tracking
initial rendernode support (via a runtime enable for now, until we get api stable),
remove old proc support,
lots of cleanups of legacy code
hdmi vendor infoframes and 4k modes
lots of gem/prime locking and races fixes
async pageflip scaffolding
drm bridge objects
- i915:
Haswell PC8+ support and eLLC support, HDMI 4K support, initial
per-process VMA pieces, watermark reworks, convert to generic hdmi
infoframes, encoder reworking, fastboot support,
- radeon:
CIK PM support, remove 3d blit code in favour of DMA engines,
Berlin GPU support, HDMI audio fixes
- nouveau:
secondary GPU power down support for optimus laptops, lots of
fixes, use MSI, VP3 engine support
- exynos:
runtime pm support for g2d, DT support, remove non-DT,
- tda998x i2c driver:
lots of fixes for sync issues
- gma500:
lots of cleanups
- rcar:
add LVDS support, fbdev emulation,
- tegra:
just minor fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (684 commits)
drm/exynos: Fix build error with exynos_drm_connector.c
drm/exynos: Remove non-DT support in exynos_drm_fimd
drm/exynos: Remove non-DT support in exynos_hdmi
drm/exynos: Remove non-DT support in exynos_drm_g2d
drm/exynos: Remove non-DT support in exynos_hdmiphy
drm/exynos: Remove non-DT support in exynos_ddc
drm/exynos: Make Exynos DRM drivers depend on OF
drm/exynos: Consider fallback option to allocation fail
drm/exynos: fimd: move platform data parsing to separate function
drm/exynos: fimd: get signal polarities from device tree
drm/exynos: fimd: replace struct fb_videomode with videomode
drm/exynos: check a pixel format to a particular window layer
drm/exynos: fix fimd pixel format setting
drm/exynos: Add NULL pointer check
drm/exynos: Remove redundant error messages
drm/exynos: Add missing of.h header include
drm/exynos: Remove redundant NULL check in exynos_drm_buf
drm/exynos: add device tree support for rotator
drm/exynos: Add missing includes
drm/exynos: add runtime pm interfaces to g2d driver
...
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=wbLt
-----END PGP SIGNATURE-----
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Changes are seen in a wide range of codes, mainly due to ASoC DAPM
requirements; HD-audio shows a high peak in diffstat, it's just a
removal of bunch of old static quirks.
Some highlights:
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and
ADAU1401(a), Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and
WM8904 based machines, Freescale S/PDIF and SSI AC'97, Renesas
R-Car SoCs, Samsung Exynos5420 SoCs, Texas Instruments PCM1681 and
PCM1792A and Wolfson Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (375 commits)
ALSA: hda - Re-setup HDMI pin and audio infoframe on stream switches
ALSA: hda - hdmi: Fallback to ALSA allocation when selecting CA
ASoC: mxs-sgtl5000: Configure the dai_links as unidirectional
ASoC: soc-pcm: Allow to specify unidirectional dai_link
ASoC: fsl_spdif: Staticse non-exported symbols
ASoC: ssm2602: Fix cache sync
ASoC: Remove unused sysfs_registered field from snd_soc_codec struct
ASoC: Remove unused debugfs_dapm field from snd_soc_{platform,codec} struct
ASoC: Remove unused control_type field from snd_soc_codec struct
ASoC: fsl: Add one blank space after ':=' in Makefile
ASoC: fsl: Add wrapping for dev_dbg() in fsl_spdif.c
ASoC: rt5640: change widget sequence for depop
ASoC: dapm: Fix auto-disable for inverted controls
ASoC: fsl: Drop SND_SOC_FSL_UTILS from SND_SOC_IMX_SPDIF
ASoC: Samsung: Do not queue cyclic buffers multiple times
ASoC: ep93xx-i2s: Remove unnecessary dev_set_drvdata()
ASoC: designware_i2s: Remove unnecessary dev_set_drvdata()
ASoC: fsl_spdif: remove redundant dev_err call in fsl_spdif_probe()
ASoC: fsl: Add S/PDIF machine driver
ASoc: kirkwood: Use the Kirkwood audio driver in Dove boards
...
When the transcoder:port mapping on Haswell HDMI/DP audio is changed
during the stream playback, the sound gets lost. Typically this
problem is seen when the user switches the graphics mode from eDP+DP
to DP-only configuration, where CRTC 1 is used for DP in the former
while CRTC 0 is used for the latter.
The graphics controller notifies the change via the normal ELD update
procedure, so we get the intrinsic event. For enabling the sound
again, the HDMI audio driver needs to reset the pin and set up the
audio infoframe again.
This patch achieves it by:
- keep the current status of channels and info frame setup in per_pin
struct,
- check the reconnection in the intrinsic event handler,
- reset the pin and the re-invoke hdmi_setup_audio_infoframe()
accordingly.
The hdmi_setup_audio_infoframe() function has been changed, too, so
that it can be invoked without passing the substream instance.
The patch is mostly based on the work by Mengdong Lin.
Cc: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_channel_allocation() tries to find a HDMI channel allocation that
matches the number channels in the playback stream and contains only
speakers that the HDMI sink has reported as available via EDID. If no
such allocation is found, 0 (stereo audio) is used.
Using CA 0 causes the audio causes the sink to discard everything except
the first two channels (front left and front right).
However, the sink may be capable of receiving more channels than it has
speakers (and then perform downmix or discard the extra channels), in
which case it is preferable to use a CA that contains extra channels
than to use CA 0 which discards all the non-stereo channels.
Additionally, it seems that HBR (HD) passthrough output does not work on
Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes
channels not present in CA). This happens with all receivers that report
a 5.1 speaker mask since a HBR stream is carried on 8 channels to the
codec.
Add a fallback in the CA selection so that the CA channel count at least
matches the stream channel count, even if the stream contains channels
not present in the sink speaker descriptor.
Thanks to GrimGriefer at OpenELEC forums for discovering that changing
the sink speaker mask allowed HBR output.
Reported-by: GrimGriefer
Reported-by: Ashecrow
Reported-by: Frank Zafka <kafkaesque1978@gmail.com>
Reported-by: Peter Frühberger <fritsch@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Add support for HDMI audio device on VGA cards that powerdown
to D3cold using non-standard ACPI/PCI infrastructure (optimus).
This does a couple of things to make it work:
a) add a set of power ops for the hdmi domain, and enables them
via vga_switcheroo when we are a switcheroo controlled card. This
just replaces the runtime resume operation so that when the card
is in D3cold the userspace pci config space access via sysfs,
the vga switcheroon runtime resume gets called first and it calls
the GPU resume callback before calling the sound card runtime
resume.
b) standard ACPI/PCI stacks won't put a device into D3cold without
an ACPI handle, but since the hdmi audio devices on gpus don't have
an ACPI handle, we need to manually force the device into D3cold
after suspend from the switcheroo path only.
c) don't try and do runtime s/r when the GPU is off.
d) call runtime suspend/resume during switcheroo suspend/resume
this is to make sure the runtime stack knows to try and resume
the hdmi audio device for pci config space access.
v2: fix incorrect runtime call suspend->resume.
v3: rework irq handler to avoid false irq when we are resuming
but haven't runtime resumed yet, don't bother trying D3cold,
it won't work, just set it manually ourselves, move runtime s/r
calls outside the main s/r hook. enable dnyamic pm properly by
dropping reference.
v4: put back irq handler check just wrap it with cap check
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Takashi Iwai