pll_a_out0 and the I2S clocks are already configured to default to rates
corresponding to a 44.1 kHz sampling rate, but the pll_a configuration
was set to a default that is not listed in the frequency table, which
caused the PLL code to compute an invalid configuration. As a result of
this invalid configuration, Jetson TK1 fails to resume from suspend.
This used to get papered over because the ASoC driver would force audio
clocks to a 44.1 kHz configuration on boot. However, that's not really
necessary and was hence removed in commit ff5d18cb04 ("ASoC: tegra:
Enable audio mclk during tegra_asoc_utils_init()").
Fix the initial rate for pll_a so that it matches the 44.1 kHz entry in
the pll_a frequency table.
Fixes: ff5d18cb04 ("ASoC: tegra: Enable audio mclk during tegra_asoc_utils_init()")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lkml.kernel.org/r/20200505071655.644773-1-thierry.reding@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Current clock driver enables PLLA, cdev1 on Tegra20 and extern1 on
Tegra30 and above as a part of clocks init and there is no need to
have these audio clocks enabled by the clock driver.
extern1 is used as parent for clk_out_1 and clk_out_1 is dedicated
for audio mclk on Tegra30 and above Tegra platforms and these clocks
are taken care by ASoC driver.
So, this patch removes audio related clocks configuration from clock
init of Tegra20 and above.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current Tegra clock driver registers PMC clocks clk_out_1, clk_out_2,
clk_out_3 and 32KHz blink output in tegra_pmc_init() which does direct
PMC register access during clk_ops and these PMC register read and write
access will not happen when PMC is in secure mode.
Any direct PMC register access from non-secure world will not go
through.
All the PMC clocks are moved to Tegra PMC driver with PMC as a clock
provider.
This patch removes tegra_pmc_clk_init along with corresponding clk ids
from Tegra clock driver.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra has no CLK_M_DIV2 and CLK_M_DIV4 clocks and instead it has
OSC_DIV2 and OSC_DIV4 clocks from OSC pads which are the possible
parents of PMC clocks for Tegra30 through Tegra210.
Tegra PMC clock parents are changed to use OSC_DIV clocks.
So, this patch removes CLK_M_DIV fixed clocks
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
OSC is one of the parent for Tegra PMC clocks clk_out_1, clk_out_2,
and clk_out_3.
This patch adds Tegra OSC to clock lookup.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra30 through Tegra210 has OSC_DIV2 and OSC_DIV4 fixed clocks
from the OSC pads.
This patch adds support for these clocks.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to allow the display driver to deal uniformly with all SOR
generations, implement the SOR clocks in a way that is compatible with
Tegra186 and later.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This makes Tegra124 and Tegra210 consistent with subsequent Tegra
generations.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR0 clock on Tegra210 is very different from the SOR0 clock found
on Tegra124. Move the Tegra124 implementation to the Tegra124 driver so
that a custom implementation can be provided on Tegra210 without
clashing with the existing clock.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the Tegra124 TRM documentation, PLLM_MISC2 register doesn't
have the lock-enable bit as well as any other PLLM-related register. Hence
PLLM re-locking can't be initiated by software. The incorrect bit setting
should have been harmless since that bit is undefined according to TRM.
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Now that clk_{readl,writel} is just an alias for {readl,writel}, we can
switch all users of clk_* to use the accessors directly and remove the
helpers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[sboyd@kernel.org: Also convert renesas file so that this can be
compile independently]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The maximum frequency supported for I2S on Tegra124 and Tegra210 is
24.576MHz (as stated in the Tegra TK1 data sheet for Tegra124 and the
Jetson TX1 module data sheet for Tegra210). However, the maximum I2S
frequency is limited to 24MHz because that is the maximum frequency of
the audio sync clock. Increase the maximum audio sync clock frequency
to 24.576MHz for Tegra124 and Tegra210 in order to support 24.576MHz
for I2S.
Update the tegra_clk_register_sync_source() function so that it does
not set the initial rate for the sync clocks and use the clock init
tables to set the initial rate instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The current default is to leave the VDE clock's parent at the default,
which is clk_m. However, that is not a configuration that will allow the
VDE to function. Reparent it to pll_c3 instead to make sure the hardware
can actually decode video content.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
By default, the vic03 clock is a child of pll_m but that runs at 924 MHz
which is too fast for VIC. Make vic03 a child of pll_c3 by default so it
will run at a supported frequency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
CDEV1 and CDEV2 clocks are a bit special case, their parent clock is
created by the pinctrl driver. It should be possible for clk user to
request these clocks before pinctrl driver got probed and hence user will
get an orphaned clock. That might be undesirable because user may expect
parent clock to be enabled by the child, so let's return -EPROBE_DEFER
till parent clock appears.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently VDE clock rate is determined by clock config left from
bootloader, let's not rely on it and explicitly specify the clock
rate in the CCF driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Machine dies if HCLK, SCLK or EMC is disabled. Hence mark these clocks
as critical.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: <stable@vger.kernel.org> # v4.16
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is used to clock the HDMI CEC interface.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move the UTMI PLL initialization code form clk-tegra<chip>.c files into
clk-pll.c. UTMI PLL was being configured and set in HW control right
after registration. However, when the clock init_table is processed and
child clks of PLLU are enabled, it will call in and enable PLLU as
well, and initiate SW enabling sequence even though PLLU is already in
HW control. This leads to getting UTMIPLL stuck with a SEQ_BUSY status.
Doing the initialization once during pllu_enable means we configure it
properly into HW control.
A side effect of the commonization/localization of the UTMI PLL init
code, is that it corrects some errors that were present for earlier
generations. For instance, in clk-tegra124.c, it used to have:
#define UTMIP_PLL_CFG1_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 6)
when the correct shift to use is present in the new version:
#define UTMIP_PLL_CFG1_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 27)
which matches the Tegra124 TRM register definition.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
[rklein: Merged in some later fixes for potential deadlocks]
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding: coding style bike-shedding, remove unused variable]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The dpaux (on Tegra124 and Tegra210) and dpaux1 (on Tegra210) are fixed
factor clocks (1:17) and derived from pll_p_out0 (pll_p). They also have
a gate bit in the peripheral clock registers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This removes the conversion from pdiv to hw, which is already taken
care of by _get_table_rate before this code is run. This avoids
incorrectly converting pdiv to hw twice and getting the wrong hw value.
Also set the input_rate in the freq cfg in _calc_dynamic_ramp_rate while
setting all the other fields.
In order to prevent regressions on earlier SoC generations, all of the
frequency tables need to be updated so that they contain the actual
divider values. If they contain hardware values these would be converted
to hardware values again, yielding the wrong value.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
[treding@nvidia.com: fix regressions on earlier SoC generations]
Signed-off-by: Thierry Reding <treding@nvidia.com>
SoC specific drivers should define the appropriate flags for each
PLL rather than relying on the registration functions to automatically
set flags on their behalf. This will properly allow for changes between
SoC generations where flags might be different and allow sharing the
same logic functions.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use unsigned int for loop variables that can never become negative and
remove a couple of gratuitous blank lines. Also use single spaces around
operators and use a single space instead of a tab to separate comments
from code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The OSC_FREQ field of the OSC_CTRL register uses the value 12 for an
oscillator frequency of 26 MHz, not 260 MHz. This isn't really critical
because I don't think boards with such an oscillator have ever existed,
much less been supported upstream.
Signed-off-by: Thierry Reding <treding@nvidia.com>
tegra_audio_clk_init was written expecting a single PLL to be
passed in directly. Change this to accept an array which will
allow for supporting multiple plls and specifying specific data
about them, like their parent, which may change over time.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The latest Tegra clk pull had some problems. Fix them.
drivers/clk/tegra/clk-tegra124.c:1450:6: warning: symbol 'tegra124_clock_assert_dfll_dvco_reset' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1466:6: warning: symbol 'tegra124_clock_deassert_dfll_dvco_reset' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1476:5: warning: symbol 'tegra124_reset_assert' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1486:5: warning: symbol 'tegra124_reset_deassert' was not declared. Should it be static?
drivers/clk/tegra/clk-dfll.c:590 dfll_load_i2c_lut() warn: inconsistent indenting
drivers/clk/tegra/clk-dfll.c:1448 dfll_build_i2c_lut() warn: unsigned 'td->i2c_lut[0]' is never less than zero.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This contains the DFLL driver needed to implement CPU frequency scaling
on Tegra.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=QWKO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.3-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.3-rc1
This contains the DFLL driver needed to implement CPU frequency scaling
on Tegra.
Clock provider drivers generally shouldn't include clk.h because
it's the consumer API. Only include clk.h in files that are using
it. Also add in a clkdev.h include that was missing in a file
using clkdev APIs.
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Save and restore this register since the LP1 restore assembly routines
fiddle with it. Otherwise the CPU would keep running on PLLX after
resume from suspend even when DFLL was the original clocksource.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DVCO present in the DFLL IP block has a separate reset line,
exposed via the CAR IP block. This reset line is asserted upon SoC
reset. Unless something (such as the DFLL driver) deasserts this
line, the DVCO will not oscillate, although reads and writes to the
DFLL IP block will complete.
Thanks to Aleksandr Frid <afrid@nvidia.com> for identifying this and
saving hours of debugging time.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
[ttynkkynen: ported to tegra124 from tegra114]
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
[mikko.perttunen: ported to special reset callback]
Signed-off-by: Mikko Perttunen <mikko.perttunen@kapsi.fi>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On Tegra124, as we now have a proper driver for the EMC.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The driver is currently only tested on Tegra124 Jetson TK1, but should
work with other Tegra124 boards, provided that correct EMC tables are
provided through the device tree. Older chip models have differing
timing change sequences, so they are not currently supported.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[treding@nvidia.com: use more consistent function names]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock has never been able to do anything.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The current parent, plld_out0, does not exist. The proper name is
pll_d_out0. While at it, rename the plld_dsi clock to pll_d_dsi_out to
be more consistent with other clock names.
Fixes: b270491eb9 ("clk: tegra: Define PLLD_DSI and remove dsia(b)_mux")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the Tegra clock driver simplifies the clock tree somewhat by
taking advantage of the fact that clk_m runs at the same frequency as
the oscillator. While that's true on all currently supported SoCs, it
does not apply to Tegra210 anymore. On Tegra210 clk_m is typically
divided down from the oscillator frequency. To support that setup, add
a separate clock for the oscillator that both clk_m and pll_ref derive
from.
Modify the tegra_osc_clk_init() function to take an additional divider
parameter for clk_m. Existing SoCs always pass in 1, whereas Tegra210
will read the divider from a register in the clock & reset controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the clocks used for HDMI audio played through the HDA controller.
Initialize the codec clock to 48Mhz and the HDA clock to 102MHz per
the TRM.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLLD is the only parent for DSIA & DSIB on Tegra124 and
Tegra132. Besides, BIT 30 in PLLD_MISC register controls
the output of DSI clock.
So this patch removes "dsia_mux" & "dsib_mux", and create
a new clock "plld_dsi" to represent the DSI clock enable
control.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Tegra132 CAR supports almost the same clocks as Tegra124 CAR. This
patch mostly deals with the small differences.
Since Tegra132 contains many of the same PLL clock sources used on
Tegra114 and Tegra124, enable them in drivers/clk/tegra/clk-pll.c when
the kernel is configured to include Tegra132 support.
This patch is based on several patches from others:
1. a patch from Peter De Schrijver:
http://lkml.iu.edu/hypermail/linux/kernel/1407.1/06094.html
2. a patch from Bill Huang ("clk: tegra: enable cclk_g at boot on
Tegra132"), and
3. a patch from Allen Martin ("clk: Enable tegra clock driver for
tegra132").
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Bill Huang <bilhuang@nvidia.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Set the parent of the dsi lp clocks to pll_p and the rate
to 68MHz. The default parent is clk_m and rate is 12MHz, this
is too slow to receive data from the peripheral.
Per NVidia HW engineers, the optimal rate is 70MHz, but 68MHz
will suffice.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
The memory controller clock runs either at half or the same frequency as
the EMC clock.
Reviewed-By: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Ensure some clocks critical for system operation are always. Also enable csite
for JTAG debugging and set the tsensor and soc_therm clock frequencies for the
upcoming soctherm driver.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
This adds two clocks, SATA and SATA_OOB, to the Tegra124 clock initialization
table. The clocks are needed for working SATA support.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
vi_sensor and vi_sensor2 have a wrong hw clkid on Tegra124. Fix this by
correcting the hw clkid for Tegra124 and creating the Tegra114 vi_sensor clock
from its own data. Tegra124 was also using the wrong internal clock id.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Initialize the XUSB-related clocks with appropriate parents and rates
for both Tegra114 and Tegra124.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Currently the Tegra1x4 clock init code hard-codes the mux setting
for xusb_hs_src and treats it as a fixed-factor clock. It is,
however, a mux which can be parented by either xusb_ss_src/2 or
pll_u_60M. Add the fixed-factor clock xusb_ss_div2 and put an
entry in periph_clks[] for the xusb_hs_src mux.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Thierry Reding