One nasty very old crash around polling for buffers that aren't there
- though that can only cause effects on drivers that support events
but not buffers.
* buffer / kfifo handling in the core.
- Check there is a buffer and return 0 from poll directly if there
isn't. Poll doesn't make sense in this circumstances, but best to close
the hole.
* ad5933
- Change the marked buffer mode to a software buffer as the meaning of
the hardware buffer label has long since changed and this uses a front
end software buffer anyway.
* ad7192
- Fix the fact the external clock frequency was only set when using the
internal clock which was less than helpful.
* adis_lib
- Initialize the trigger before requesting the interrupt. Some newer
parts can power up with interrupt generation enabled so ordering now
matters.
* aspeed-adc
- Fix an errror handling path as labels and general ordering were wrong.
* srf08
- Fix a link error due to undefined devm_iio_triggered_buffer_setup.
* stm32-adc
- Fix error handling unwind squence in stm32h7_adc_enable.
-----BEGIN PGP SIGNATURE-----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=x9oo
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.16 cycle.
One nasty very old crash around polling for buffers that aren't there
- though that can only cause effects on drivers that support events
but not buffers.
* buffer / kfifo handling in the core.
- Check there is a buffer and return 0 from poll directly if there
isn't. Poll doesn't make sense in this circumstances, but best to close
the hole.
* ad5933
- Change the marked buffer mode to a software buffer as the meaning of
the hardware buffer label has long since changed and this uses a front
end software buffer anyway.
* ad7192
- Fix the fact the external clock frequency was only set when using the
internal clock which was less than helpful.
* adis_lib
- Initialize the trigger before requesting the interrupt. Some newer
parts can power up with interrupt generation enabled so ordering now
matters.
* aspeed-adc
- Fix an errror handling path as labels and general ordering were wrong.
* srf08
- Fix a link error due to undefined devm_iio_triggered_buffer_setup.
* stm32-adc
- Fix error handling unwind squence in stm32h7_adc_enable.
Here is the big Staging and IIO driver patches for 4.16-rc1.
There is the normal amount of new IIO drivers added, like all releases.
The networking IPX and the ncpfs filesystem are moved into the staging
tree, as they are on their way out of the kernel due to lack of use
anymore.
The visorbus subsystem finall has started moving out of the staging tree
to the "real" part of the kernel, and the most and fsl-mc codebases are
almost ready to move out, that will probably happen for 4.17-rc1 if all
goes well.
Other than that, there is a bunch of license header cleanups in the
tree, along with the normal amount of coding style churn that we all
know and love for this codebase. I also got frustrated at the
Meltdown/Spectre mess and took it out on the dgnc tty driver, deleting
huge chunks of it that were never even being used.
Full details of everything is in the shortlog.
All of these patches have been in linux-next for a while with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLxoA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk4vgCgjeMlwhtar65DIticIRj626EFxiQAnjGmH8Kd
d9Xz2Piq8X47uSsC/6AE
=xxMT
-----END PGP SIGNATURE-----
Merge tag 'staging-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big Staging and IIO driver patches for 4.16-rc1.
There is the normal amount of new IIO drivers added, like all
releases.
The networking IPX and the ncpfs filesystem are moved into the staging
tree, as they are on their way out of the kernel due to lack of use
anymore.
The visorbus subsystem finall has started moving out of the staging
tree to the "real" part of the kernel, and the most and fsl-mc
codebases are almost ready to move out, that will probably happen for
4.17-rc1 if all goes well.
Other than that, there is a bunch of license header cleanups in the
tree, along with the normal amount of coding style churn that we all
know and love for this codebase. I also got frustrated at the
Meltdown/Spectre mess and took it out on the dgnc tty driver, deleting
huge chunks of it that were never even being used.
Full details of everything is in the shortlog.
All of these patches have been in linux-next for a while with no
reported issues"
* tag 'staging-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (627 commits)
staging: rtlwifi: remove redundant initialization of 'cfg_cmd'
staging: rtl8723bs: remove a couple of redundant initializations
staging: comedi: reformat lines to 80 chars or less
staging: lustre: separate a connection destroy from free struct kib_conn
Staging: rtl8723bs: Use !x instead of NULL comparison
Staging: rtl8723bs: Remove dead code
Staging: rtl8723bs: Change names to conform to the kernel code
staging: ccree: Fix missing blank line after declaration
staging: rtl8188eu: remove redundant initialization of 'pwrcfgcmd'
staging: rtlwifi: remove unused RTLHALMAC_ST and RTLPHYDM_ST
staging: fbtft: remove unused FB_TFT_SSD1325 kconfig
staging: comedi: dt2811: remove redundant initialization of 'ns'
staging: wilc1000: fix alignments to match open parenthesis
staging: wilc1000: removed unnecessary defined enums typedef
staging: wilc1000: remove unnecessary use of parentheses
staging: rtl8192u: remove redundant initialization of 'timeout'
staging: sm750fb: fix CamelCase for dispSet var
staging: lustre: lnet/selftest: fix compile error on UP build
staging: rtl8723bs: hal_com_phycfg: Remove unneeded semicolons
staging: rts5208: Fix "seg_no" calculation in reset_ms_card()
...
Error handling in stm32h7_adc_enable routine doesn't unwind enable
sequence correctly. ADEN can only be cleared by hardware (e.g. by
writing one to ADDIS).
It's also better to clear ADRDY just after it's been set by hardware.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
iio_priv does not return an error pointer, so check is not valid.
Patch suppresses it.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data to optimize the source code.
No check is needed on dev_data as match table is defined in driver.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The labels and branching order of the error path of 'aspeed_adc_probe()'
are broken.
Re-order the labels and goto statements.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In case of error, the function devm_iio_device_alloc() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: e2e6771c64 ("IIO: ADC: add STM32 DFSDM sigma delta ADC support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Building with CONFIG_OF disabled produces a compiler warning:
drivers/iio/adc/stm32-dfsdm-core.c: In function 'stm32_dfsdm_probe':
drivers/iio/adc/stm32-dfsdm-core.c:245:22: error: unused variable 'pnode' [-Werror=unused-variable]
This removes the variable and open-codes it in the only place
it gets used to avoid that warning.
Fixes: bed73904e7 ("IIO: ADC: add stm32 DFSDM core support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This code offers a way to handle PDM audio microphones in
ASOC framework. Audio driver should use consumer API.
A specific management is implemented for DMA, with a
callback, to allows to handle audio buffers efficiently.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DFSDM driver to handle sigma delta ADC.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for stm32 DFSDM pheripheral. Its converts a sigma delta
stream in n bit samples through a low pass filter and an integrator.
stm32-dfsdm-core driver is the core part supporting the filter
instances dedicated to sigma-delta ADC or audio PDM microphone purpose.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add generic driver to support sigma delta modulators.
Typically, this device is hardware connected to
an IIO device in charge of the conversion. Devices are
bonded through the hardware consumer API.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default, watermark is set to '1'. Watermark is used to fine tune
cyclic dma buffer period. In case watermark is left untouched (e.g. 1)
and several channels are being scanned, buffer period is wrongly set
(e.g. to 1 sample). As a consequence, data is never pushed to upper layer.
Fix buffer period size, by taking scan channels number into account.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the patch to the file ti_am335x_adc.c
which fixes the following coccinelle warning:
WARNING: Comparison to bool
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the registers are read out once per conversion interval. If
the reading is delayed as the conversion has not yet finished, this extra
time is treated as being part of the readout, although it should delay
the start of the poll interval. This results in the interval starting
slightly earlier in each iteration, until all time between reads is
spent polling the status registers instead of sleeping.
To fix this, the delay has to account for the state of the conversion
ready flag. Whenever the conversion is already finished, schedule the next
read on the regular interval, otherwise schedule it one interval after the
flag bit has been set.
Split the work function in two functions, one for the status poll and one
for reading the values, to be able to note down the time when the flag
bit is raised.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the timestamp is no longer (ab-)used to measure the function run time,
it can be taken at the correct time, i.e. when the conversion has finished.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iio timestamp clock is user selectable and may be non-monotonic. Also,
only part of the acquisition time is measured, thus the delay was longer
than intended.
Use a monotonic timestamp to track the time for the next poll iteration.
The timestamp is advanced by the sampling interval each iteration. In case
the conversion overrruns the register readout (i.e. fast sampling combined
with a slow bus), one or multiple samples will be dropped.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)
Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.
Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)
This is a part of the patchset: https://lkml.org/lkml/2017/11/22/394
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to the at91_adc.c file that fixes up a brace
warning found by the checkpatch.pl tool
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return value in hx711_reset() should indicate status of dout otherwise the
calling function is reporting an error as false positive
If there are two reads too close to each other, then the second one will
never succeed. This happens especially when using buffered mode with both
channels enabled.
When changing the channel on every trigger event the former 100 ms are not
enough for waiting until the device indicates normal mode.
Wait up to 1 second until the device turns into normal mode.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add buffer to device data struct and add trigger function
Data format is quite simple:
voltage - channel 0 32 Bit
voltage - channel 1 32 Bit
timestamp 64 Bit
Using both channels at the same time is working quite slow because of
changing the channel which needs a dummy read.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conversion time can be up to 16 seconds (8 ms per channel, 2 channels,
1024 times averaging).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the datasheet states the CNVR flag is cleared by reading the
BUS_VOLTAGE register, it is actually cleared by reading any of the
voltage/current/power registers.
The behaviour has been confirmed by TI support:
http://e2e.ti.com/support/amplifiers/current-shunt-monitors/f/931/p/647053/2378282
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timestamp is inserted into the buffer after the sample data by
iio_push_to_buffers_with_timestamp, document the space requirement for
the timestamp.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iio_push_to_buffers_with_timestamp expects a void pointer, so the cast
is both unnecessary and misleading.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Meson8 devices the channel muxes are not programmed. This
results in garbage values when trying to read channels that are not set
up.
Fix this by initializing the channel 0 and 1 muxes in
MESON_SAR_ADC_CHAN_10_SW as well as the muxes for all other channels in
MESON_SAR_ADC_AUX_SW based on what the vendor driver does (which is
simply a 1:1 mapping of channel number and channel mux).
This only showed up on Meson8 devices, because for GXBB and newer BL30
is taking care of initializing the channel muxes.
This additionally fixes a typo in the
MESON_SAR_ADC_AUX_SW_MUX_SEL_CHAN_MASK macro because the old definition
assumed that the register fields were 2 bit wide, while they are
actually 3 bit wide.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GX SoCs use a 1.2 MHz ADC clock, while the older SoCs use a 1.14 MHz
clock.
A comment in the driver from Amlogic's GPL kernel says that it's
running at 1.28 MHz. However, it's actually programming a divider of
20 + 1. With a XTAL clock of 24 MHz this results in a frequency of
1.14 MHz. (their calculation might be based on a 27 MHz XTAL clock,
but this is not what we have on the Meson8 and Meson8b SoCs).
The ADC was still working with the 1.2MHz clock. In my own tests I did
not see a difference between 1.2 and 1.14 MHz (regardless of the clock
frequency used, the ADC results were identical).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge issue pointed out by Stephen in
drivers/iio/adc/meson_saradc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO core provides a handy GPIO_LOOKUP() macro to populate a struct
gpiod_lookup array without having to spell out attribute names (but
still avoid breakage when attributes within the struct are rearranged
or added).
The axp288_adc.c driver uses a similar macro to populate a struct
iio_map array. Make it available to others.
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The "sana" clock is not used at SAR ADC module in Amlogic Meson SoC,
it is irrelevant for the SAR ADC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Meson GXBB and newer SoCs have a few more registers than the older
Meson8 and Meson8b SoCs.
Use a separate regmap config to limit the older SoCs to the DELTA_10
register.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8 and Meson8b do not have the MESON_SAR_ADC_REG11 register. The
bandgap setting for these SoCs is configured in the
MESON_SAR_ADC_DELTA_10 register instead.
Make the driver aware of this difference and use the correct bandgap
register depending on the SoC.
This has worked fine on Meson8 and Meson8b because the bootloader is
already initializing the bandgap setting.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8 and Meson8b SoCs use the the SAR ADC gate clock provided by the
MESON_SAR_ADC_REG3 register within the SAR ADC register area.
According to the datasheet (and the existing MESON_SAR_ADC_REG3_CLK_EN
definition) the gate is on bit 30.
The fls() function returns the last set bit, which is "bit index + 1"
(fls(MESON_SAR_ADC_REG3_CLK_EN) returns 31). Fix this by switching to
__ffs() which returns the first set bit, which is bit 30 in our case.
This off by one error results in the ADC not being usable on devices
where the bootloader did not enable the clock.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_adc_probe(), positive IRQ numbers are also taken as error cases.
Use "if (ddata->irq < 0)" instead of "if (!ddata->irq)" to validate the
return value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: 25ec249632 ("iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ASPEED SoC must deassert a reset in order to use the ADC peripheral.
The device tree bindings are updated to document the resets phandle, and
the example is updated to match what is expected for both the reset and
clock phandle. Note that the bindings should have always had the reset
controller, as the hardware is unusable without it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32H7 ADC channels can be configured either as single ended or
differential with 'st,adc-channels' or 'st,adc-diff-channels'
(positive and negative input pair: <vinp vinn>, ...).
Differential channels have different offset and scale, from spec:
raw value = (full_scale / 2) * (1 + (vinp - vinn) / vref).
Add offset attribute.
Differential channels are selected by DIFSEL register. Negative
inputs must be added to pre-selected channels as well (PCSEL).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove const array that defines channels. Build channels definition
at probe time, when initializing channels (only for requested ones).
This will ease adding differential channels support.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reducing shunt and bus voltage range improves the accuracy, so allow
altering the default settings.
Both settings are exposed as gain values. While for the shunt voltage
this is straightforward, the bus range settings of 32V (default) and 16V
are mapped to gain values of 1 resp. 2, to provide a uniform API to
userspace.
As the gain settings are incorporated into the raw values by the sensor
itself, adjusting of the scale attributes is not necessary.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While the config uses the physical value corresponding to the LSB
for both the power and the bus voltage register, the shunt voltage is
specified as parts of 1 mV. Use the LSB physical value for all registers.
No functional change.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lower bits of the INA219/220 bus voltage register are conversion
status flags, properly shift the value.
When reading via IIO buffer, the value is passed on unaltered,
shifting is the responsibility of the user.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Need to acknowledge DRDY irq in direct mode/ software
triggered mode. Otherwise, on the next conversion, overrun
flag will be raised, which is not a correct state.
This doesn't affect the functionality, but will generate
possible incorrect overrun reports.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support for DMA transfers. The implementation uses the user watermark
to decide whether DMA will be used or not. For watermark 1, DMA will not be
used. If watermark is bigger, DMA will be used.
Sysfs attributes are created to indicate whether the DMA is used,
with hwfifo_enabled, and the current DMA watermark is readable
in hwfifo_watermark. Minimum and maximum values are in hwfifo_watermark_min
and hwfifo_watermark_max.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The module license checker complains about these two so just fix
it up. They are both GPLv2, both written by me or using code
I extracted while refactoring from the GPLv2 drivers.
Cc: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device support
* ti-dac082s085 dac
- new driver supporting 8, 10 and 12 bit TI DACs with 2 and 4 channels:
DAC082S085, DAC102S085, DAC122S085, DAC104s085 and DAC124S085.
Minor features and cleanps
* adc12138
- make array ch_to_mux static for small object code size reduction.
* sun4i-gpadc
- use of_device_get_match_data rather than opencoding it.
* stm32 trigger
- add tim15 tigger on STM32H7
- check clock rate to avoid potential division by zero
* tsl2x7x staging cleanups.
- move *_thresh_period to being created by IIO core.
- remove unused tsl2x7x_parse_result structure.
- sort includes
- drop a repeat iio_dev forward definition
- fix some code alignment of defines.
- use IIO_CONST_ATTR for constant string attribute
- drop some unnecessary parentheses
- fix various alignment with parenthese
- rename power defines for readability reasons
- fix a missaligned break statement
- Tidy up function definitions so they fit on a single line.
-----BEGIN PGP SIGNATURE-----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=IXO+
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of new device support, cleanups and features for IIO in the 4.15 cycle
New device support
* ti-dac082s085 dac
- new driver supporting 8, 10 and 12 bit TI DACs with 2 and 4 channels:
DAC082S085, DAC102S085, DAC122S085, DAC104s085 and DAC124S085.
Minor features and cleanps
* adc12138
- make array ch_to_mux static for small object code size reduction.
* sun4i-gpadc
- use of_device_get_match_data rather than opencoding it.
* stm32 trigger
- add tim15 tigger on STM32H7
- check clock rate to avoid potential division by zero
* tsl2x7x staging cleanups.
- move *_thresh_period to being created by IIO core.
- remove unused tsl2x7x_parse_result structure.
- sort includes
- drop a repeat iio_dev forward definition
- fix some code alignment of defines.
- use IIO_CONST_ATTR for constant string attribute
- drop some unnecessary parentheses
- fix various alignment with parenthese
- rename power defines for readability reasons
- fix a missaligned break statement
- Tidy up function definitions so they fit on a single line.
Greg Kroah-Hartman