Based on Chandra's earlier patches in linux-omap tree.
Note that omap1_mcbsp_check and omap2_mcbsp_check are no longer
needed as there's now omap_mcbsp_check_valid_id() defined.
Also some functions can now be marked __init.
Signed-off-by: Chandra Shekhar <x0044955@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use __init but __devinit to define probe function. A pointer to
omap_mcbsp_probe is passed to the core via platform_driver_register and
so the function must not disappear when the init code is freed. Using
__init and having HOTPLUG=y the following probably oopses:
echo -n omap-mcbsp.1 > /sys/bus/platform/driver/omap-mcbsp/unbind
echo -n omap-mcbsp.1 > /sys/bus/platform/driver/omap-mcbsp/bind
While at it move the remove function to the .devexit.text section.
Signed-off-by: Uwe Kleine-König <ukleinek@strlen.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc updates from linux-omap tree, mostly to update common
device initialization and add missing defines from linux-omap
tree. Also some changes to make room for adding 34xx in
following patches.
Note that the I2C resources are now set up in
arch/arm/plat-omap/i2c.c helper, and can be removed
from devices.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix sparse, checkpatch warnings fro GPMC code.
Also change to use ioremap, and add missing function prototypes
to gpmc.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds pinmux support for OMAP3. Incorporated review comments
from Tony to make mux_value as bit mask. Tested on 3430SDP.
Also merge in adding of I2C pins from Jarkko Nikula.
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some register offsets are different for 242x and 243x. This
will allow compiling sleep code for both chips into the same
kernel. Pass the addresses for SDRC_DDLA_CTRL and SDRC_POWER to the
omap24xx_cpu_suspend instead of loading the values since the only.
Also fix a bug to call omap2_sram_suspend with the value of SDRC_DLLA_CTRL
instead of the address as that's what omap24xx_cpu_suspend expects to
determine between DDR and SDR. This bug has not been noticed as
the boards seem to have DDR instead of SDR.
Note that some PM patches are still missing. The PM patches will
be added later on once the base files are in sync with linux-omap
tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common function to enable/disable omap2/3 uart
clocks. Enabled uarts are passed by bootloader in atags and clocks for
these enabled uarts are touched.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The structures weren't ready for this change:
arch/arm/plat-omap/devices.c:320: error: 'struct omap_mmc_conf' has no member named 'internal_clock'
arch/arm/plat-omap/devices.c:326: error: implicit declaration of function 'omap_ctrl_readl'
arch/arm/plat-omap/devices.c:326: error: 'OMAP2_CONTROL_DEVCONF0' undeclared (first use in this function)
arch/arm/plat-omap/devices.c:328: error: implicit declaration of function 'omap_ctrl_writel'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAPs MMC device data was passing the wrong structure via the platform
device. Moreover, a missing function means that both sx1_defconfig
and omap_h2_1610_defconfig builds failed with
undefined reference to `omap_set_mmc_info'
errors. Fix this by updating the MMC support from the omapzoom tree.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
gpio.c wilfully casts physical addresses to void __iomem * and then
fixes them up at runtime using:
bank->base = IO_ADDRESS(bank->base);
where accesses prior to this fixup are via omap_read/omap_write, and
after are by __raw_read/__raw_write. This doesn't lend itself to
static checking, nor to easy understanding of the code.
And so, OMAP_MPUIO_BASE gets to be the right type - integer like since
it's a physical address, not a MMIO pointer.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP1_IO_ADDRESS(), OMAP2_IO_ADDRESS() and IO_ADDRESS() returns cookies
for use with __raw_{read|write}* for accessing registers. Therefore,
these macros should return (void __iomem *) cookies, not integer values.
Doing this improves typechecking, and means we can find those places
where, eg, DMA controllers are incorrectly given virtual addresses to
DMA to, or physical addresses are thrown through a virtual to physical
address translation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make is_omap_port() take the uart_8250_port structure so it can do
whatever test it desires. Convert the test to compare the physical
addresses rather than virtual addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mcbsp is confused as to what takes a physical or virtual address.
Fix the two instances where it gets it wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/plat-omap/gpio.c: In function '_omap_gpio_init':
arch/arm/plat-omap/gpio.c:1492: error: 'omap_mpuio_device' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Oprofile kernel support for ARMv7.
Tested on OMAP3430 and OMAP3530 chipsets (Cortex-A8).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP3430ES2+ introduces a new feature: optional powerdomain context
hardware save-and-restore (SAR). Currently, this feature only applies
to USBHOST and USBTLL module context when the USBHOST or CORE
powerdomains enter a low-power sleep state[1]. This feature avoids
re-enumeration of USB devices when the powerdomains return from idle,
which is potentially time-consuming.
This patch adds support for enabling and disabling hardware
save-and-restore to the powerdomain code. Three new functions are
added, pwrdm_enable_hdwr_sar(), pwrdm_disable_hdwr_sar(), and
pwrdm_can_hdwr_sar(). A new struct powerdomain "flags" field is
added, with a PWRDM_HAS_HDWR_SAR flag to indicate powerdomains with
SAR support.
Thanks to Jouni Högander <jouni.hogander@nokia.com> for reviewing an
earlier version of these patches, and Richard Woodruff <r-woodruff2@ti.com>
for clarifying the purpose of these bits.
1. For the USBHOST controller module, context loss occurs when the
USBHOST powerdomain enters off-idle. For USBTLL, context loss
occurs either if CORE enters off-idle, or if the CORE logic is
configured to turn off when CORE enters retention-idle (OSWR).
34xx ES2 TRM 4.8.6.1.1, 4.8.6.1.2
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Associate each OMAP24xx clock in arch/arm/mach-omap2/clock24xx.h
with a clockdomain.
Also move the L4 clock up higher in the file in preparation to
define the SSI L4 iclk.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Thie patch adds code to the powerdomain layer to track the
clockdomains associated with each powerdomain.
It also modifies the clockdomain code to register clockdomains
with their corresponding powerdomain when the clockdomain is registered.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch creates an interface to the clockdomain registers in the
PRM/CM modules on OMAP2/3. This interface is intended to be used by
PM code, e.g., pm.c; not by device drivers directly.
The patch also adds clockdomain usecount tracking. This is intended
to be called whenever the first clock in a clockdomain is enabled, or
when the last enabled clock in a clockdomain is disabled. If the
clockdomain is in software-supervised mode, the code will force-wakeup
or force-sleep the clockdomain. If the clockdomain is in
hardware-supervised mode, the first clock enable will add sleep and
wakeup dependencies on a user-selectable set of parent domains (usually
MPU & IVA2), and the disable will remove them.
Each clockdomain will be defined in later patches as static
structures. The clockdomain structures are linked into a list at boot
by clkdm_register(), similar to the OMAP clock code.
The patch adds a Kconfig option, CONFIG_OMAP_DEBUG_CLOCKDOMAIN, which
when enabled will emit verbose debug messages via pr_debug().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch creates an interface to the powerdomain registers in the
PRM/CM modules on OMAP2/3. This interface is intended to be used by
PM code, e.g., pm.c; not by device drivers directly.
Each powerdomain will be defined in later patches as static
structures. Also defined are dependencies between powerdomains,
used for adding and removing PM_WKDEP and CM_SLEEPDEP bits. The
powerdomain structures are linked into a list at boot by
pwrdm_register(), similar to the OMAP clock code.
The patch adds a Kconfig option, CONFIG_OMAP_DEBUG_POWERDOMAIN, which
when enabled will emit verbose debug messages via pr_debug().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP at least gets the return type(s) for the DMA translation functions
wrong, which can lead to subtle errors. Avoid this by moving the DMA
translation functions to asm/dma-mapping.h, and converting them to
inline functions.
Fix the OMAP DMA translation macros to use the correct argument and
result types.
Also, remove the unnecessary casts in dmabounce.c.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of this field need a PFN instead of a physical address,
so replace node_boot_start with node_min_pfn.
[Lee.Schermerhorn@hp.com: fix spurious BUG_ON() in mark_bootmem()]
Signed-off-by: Johannes Weiner <hannes@saeureba.de>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kobjects do not have a limit in name size since a while, so stop
pretending that they do.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New struct omap_globals contains the omap processor specific
module bases. Use omap_globals to set the various base addresses
to make detecting omap chip type simpler.
Also introduce OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS for future multi-omap
patches.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change omap USB code to use omap_read/write instead of __REG for multi-omap
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Cc: i2c@lm-sensors.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
debugfs can provide the infrastructure to trace the dependencies of
clock tree hierarchy quite visibly. This patch enables to keep track
of clock tree hierarchy and expose their attributes under each clock
directry as below:
omap:~# tree -d -L 2 /debug/clock/omap_32k_fck/
/debug/clock/omap_32k_fck/
|-- gpt10_fck
|-- gpt11_fck
|-- gpt1_fck
|-- per_32k_alwon_fck
| |-- gpio2_fck
| |-- gpio3_fck
| |-- gpio4_fck
| |-- gpio5_fck
| |-- gpio6_fck
| `-- wdt3_fck
|-- ts_fck
`-- wkup_32k_fck
|-- gpio1_fck
`-- wdt2_fck
14 directories
omap:~# tree /debug/clock/omap_32k_fck/gpt10_fck/
/debug/clock/omap_32k_fck/gpt10_fck/
|-- flags
|-- rate
`-- usecount
0 directories, 3 files
Although, compared with David Brownell's small patch, this may look
bit overkilling, I expect that this debugfs can deal with other PRCM
complexities at the same time. For example, powerdomain dependencies
can be expressed by using symbolic links of these clocks if
powerdomain supports dubgfs as well.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch transform mcbsp code to use platform data
from arch/arm/plat-omap/devices.c
It also gets ride of ifdefs on mcbsp.c code.
To do it, a platform data structure was defined.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fix lots of warnings and errors reported by
scripts/checkpatch.pl on arch/arm/plat-omap/mcbsp.c.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove __REG access in DMA code, use dma_read/write instead:
- dynamically set the omap_dma_base based on the omap type
- omap_read/write becomes dma_read/write
- dma channel registers are read with dma_ch_read/write
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch optimizes the timer load and start sequence. By combining the
load and start a needless posted wait can be removed from the system timer
execution path.
* Before patch register writes are taking up .078% @ 500MHz during idle.
Address |total |min |max |avr |count|ratio%
old\process\default_idle|7.369s |0.0us|999.902ms|14.477ms|509. |62.661%
ld\Global\cpu_v7_do_idle|4.265s |0.0us|375.786ms|24.374ms|175. |36.270%
(UNKNOWN)|17.503ms|0.us|531.080us|5.119us|3419. |0.148%
r\omap_dm_timer_set_load|8.135ms|0.0us|79.887us|15.065us|540. |0.069% <--
\vmlinux-old\Global\_end|2.023ms|0.0us|4.000us|0.560us|3613. |0.017%
-old\Global\__raw_readsw|1.962ms|0.0us|108.610us|9.167us|214. |0.016%
old\smc91x\smc_interrupt|1.353ms|0.0us|10.212us|2.348us|576. |0.011%
s/namei\__link_path_walk|1.161ms|0.0us|4.310us|0.762us| 1524. |0.009%
\omap_dm_timer_write_reg|1.085ms|0.0us|126.150us|2.153us|504. |0.009% <--
* After patch timer functions do not show up in top listings for long captures.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the use of write posting for the timer. Previously, every
write could lock the requestor for almost 3x32KHz cycles. This patch only
synchronizes before writes and reads instead of after them and it does
it on per register basis. Doing it this way there is some chance to hide
some of the sync latency. It also removes some needless reads when
non-posted mode is there. With out this fix the read/writes take almost
2% CPU load @500MHz just waiting on tick timer registers.
Also define new 34xx only registers.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Channel should be marked active only when DMA is really started. Otherwise
just omap_request_dma, omap_dma_link_lch and omap_dma_unlink_lch will cause
incorrect dump_stack().
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/plat-omap/clock.c:397: warning: "struct cpufreq_frequency_table" declared inside parameter list
arch/arm/plat-omap/clock.c:397: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-omap/clock.c: In function `clk_init_cpufreq_table':
arch/arm/plat-omap/clock.c:402: error: structure has no member named `clk_init_cpufreq_table'
arch/arm/plat-omap/clock.c:403: error: structure has no member named `clk_init_cpufreq_table'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Function enable_lnk does incorrect channel link on non-omap1 builds if chain
is created manually with omap_request_dma and omap_dma_link_lch functions.
Fix this by making sure that next_linked_ch field is initialized to -1 just
in omap_request_dma.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
This patch changes 24xx to use shared clock code and new register
access.
Note that patch adds some temporary OLD_CK defines to keep patch
more readable. These temporary defines will be removed in the next
patch. Also not all clocks are changed in this patch to limit the
size.
Also, the patch fixes few incorrect clock defines in clock24xx.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use new register access, except for clock
framework. Clock framework register access will get updates in the
next patch.
Note that board-*.c files change GPMC (General Purpose Memory Controller)
access to use gpmc_cs_write_reg() instead of accessing the registers
directly. The code also uses gpmc_fck instead of it's parent clock
core_l3_ck for GPMC clock.
The H4 board file also adds h4_init_flash() function, which specify the
flash start and end addresses.
Also note that sleep.S removes some unused registers addresses.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.
Only change USB platform init code to use new register access, other
access will be changed in later patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc clean-up for the mux code and remove some unnecessary
ifdefs. Patch changes debug function so it can be used on
both 24xx and 34xx.
Changes are mostly for omap2, but patch also cleans up some
omap1 and common mux code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move now OMAP1-specific timer32k code to mach-omap1 since OMAP2/3 32k
timers are done in gptimer code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 32k timer code is moving to OMAP1 specific dir, move the
32k-based sched_clock() into common code where it is based on the 32k
sync counter and can be used even when using MPU timer.
While moving, change the ticks-to-nsecs conversion to use the helper
functions provided by clocksource.h.
Also removed the unused ticks_to_usec, leaving only ticks_to_nsec.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.
This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.
Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used. Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.) This
is important for sleep/suspend so there is a valid counter during
sleep. Note that the suspend/sleep code needs fixing to check for
overflows of this counter.
In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics. A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap processor specific function depending on system type.
Based on an earlier patch by Klaus Pedersen <klaus.k.pedersen@nokia.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.
This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the GPIO interrupt handling is duplicating some of the work
done by the generic IRQ handlers (handle_edge_irq, handle_level_irq)
such as detecting nesting, handling re-triggers etc. Remove this
duplication and use generic hooks based on IRQ type.
Using generic IRQ handlers ensures correct behavior when using
threaded interrupts introduced by the -rt patch.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clearing was moved to the unmask hook because it is known to run
after the interrupt handler has actually run. Before this patch, if
interrupts are threaded, the clearing/unmasking of level triggered
interrupts would be done before the threaded handler actually ran.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes the return value of omap_dma_chain_a_transfer
to 0 on success instead of the flag 'start_dma', which wasn't really useful
for anything.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although audio and dsp drivers are not integrated yet,
allow compiling in mailbox and mcbsp to see any build
warnings.
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO IRQ unmask doesn't actually do anything useful. The problem is
hidden by a separate explicit mass unmask at the end of the chained
bank handler.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One-shot mode was broken in MPU-timer support for OMAP1 due to a typo.
Also, ensure timer is stopped before changing the auto-reload flag.
The TRM says changing the AR flag when timer is running is undefined.
Also set GENERIC_CLOCKEVENTS for all omaps.
Signed-off-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix some spinlock issues reported by lockdep: since the gpio bank
locks can be aquired in both irq and non-irq contexts, they need
to be consistent about always using the irq-safe variants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In mainline, the "old style" I2C registration was only removed for
OMAP2, leading to init-time bugs (regressions) like:
sysfs: duplicate filename 'i2c_omap.1' can not be created
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:424 sysfs_add_one+0x40/0xd4()
Modules linked in:
... deletia ...
[<c0036a38>] (omap_init_i2c+0x0/0x50) from [<c000cea8>] (omap_init_devices+0x10/0x24)
r4:c001e000
[<c000ce98>] (omap_init_devices+0x0/0x24) from [<c0008684>] (do_initcalls+0x78/0x200)
... deletia ...
---[ end trace ca143223eefdc828 ]---
kobject_add_internal failed for i2c_omap.1 with -EEXIST, don't try to register things with the same name in the same directory.
The fix is obvious: remove the old init code, it's no longer needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes parameter passing to DMA handlers uniform between non-chained
and chained transfers and makes debugging easier. Additional data like
chain_id can be always passed to handlers via callback data if needed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This helper module simplifies I2C bus registration for different OMAP
platforms by doing registration in one place only and to allow board
specific bus configuration like clock rate and number of busses configured.
Helper should cover OMAP processors from first to third generation.
This patch just adds the feature and current implementation cleanup and
board file modifications will be done in following patches.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DM timer support for OMAP3.
Fixed source clocks for 3430 by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleanup DM timer list for OMAP2 and OMAP1 to allow
adding support for 3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DMA support for chaining and 3430.
Also remove old DEBUG_PRINTS as noted by Russell King.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add 24xx GPIO debounce support. Also minor formatting
clean-up.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 3430 gpio support.
It also contains a fix by Paul Walmsley <paul@pwsan.com> to use the
correct clock names for OMAP3430.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP1 some McBSP features depend on DSP. Also export
polling functions as suggested by Luis Cargnini.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: <linux-arch@vger.kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
This patch converts arm's OMAP mailbox driver to use
blk_end_request interfaces.
If the original code was converted literally, blk_end_request would
be called with '-EIO' because end_that_request_last() were called
with '0' (i.e. failure).
But I think these '0's are bugs in the original code because it's
unlikely that all requests are treated as failure.
(The bugs should have no effect unless these requests have an end_io
callback.)
So I changed them to pass '0' (i.e. success) to blk_end_request.
Cc: Toshihiro Kobayashi <toshihiro.kobayashi@nokia.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
mach-integrator/pci_v3.c: no need to reference 'irq' arg, its constant
mach-omap1/pm.c: remove extra whitespace
arch/arm/mach-sa1100/ssp.c: remove braces around single C stmt
arch/arm/plat-omap/mcbsp.c:
- remove pointless casts from void*
- make longer lines more readable
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a section error on OMAP when the framebuffer is enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Convert files to UTF-8.
* Also correct some people's names
(one example is Eißfeldt, which was found in a source file.
Given that the author used an ß at all in a source file
indicates that the real name has in fact a 'ß' and not an 'ss',
which is commonly used as a substitute for 'ß' when limited to
7bit.)
* Correct town names (Goettingen -> Göttingen)
* Update Eberhard Mönkeberg's address (http://lkml.org/lkml/2007/1/8/313)
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The SoSSI driver should already take care of this by enabling / disabling
its clock when necessary, so this legacy callout from the PM idle code
is not needed any more.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Additional cleanup for debug boards on H2/P2/H3/H4: move the init
code that's not board-specific into a new file where it can be easily
shared between all the different boards (avoiding code duplication,
and making it easier to support more devices). Make H4 use that.
This should be easy to drop in to the OMAP1 boards using these debug
cards; the only difference seems to be that the p2 does an extra reset
of the smc using the fpga (probably all boards could do that, if it's
necessary) and doesn't use the gpio mux or request APIs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the OMAP1 version of omap_dm_timer_get_fclk(), and its associated
compile-time warning. It would only BUG() if called, while it's only
called on OMAP2.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.
Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.
Fixup the existing users.
Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.
[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some OMAP 24xx pin mux declarations to support:
- TUSB 6010 EVM (on H4)
- All three full speed USB ports
- GPIOs used with USB0 on Apollon and H4
For OMAP2, issue MUX_WARNINGS and debug messages correctly; and make the
message look more like the OMAP1 message.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix GCC-reported compile time bug which prevents booting
when the framebuffer code is disabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Partial fix for CONFIG_LEDS breakage ... at least allow platforms
using the debug-leds support (H4 for now) to build with the generic
LED support, and default the LED that would be the timer LED to
trigger using the "heartbeat" (timer driven, rate depends on load).
Right now only H2 and P2 seem to have working LED support; this
at least makes H4 less broken.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clocks with the follow parent rate mode were not updating their
children at propagate rate time.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- in addition to fixed FB regions - as passed by the bootloader -
allow dynamic allocations
- do some more checking against overlapping / reserved regions
- move the FB specific parts out from sram.c to fb.c
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Mostly cosmetic to sync up with linux-omap tree
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a generic mailbox interface for for DSP and IVA
(Image Video Accelerator). This patch itself doesn't contain
any IVA driver.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch syncs omap specific core code with linux-omap.
Most of the changes are needed to fix bitrot caused by
driver updates in linux-omap tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds generic support for the "debug board" LEDs used by most of
TI's OMAP reference boards, and board-specific support for the H4.
It's derived from the not-as-generic stuff used by OMAP1 H2/H3/P2.
Those should be able to switch easily to this version, and clean up
some of the omap1-specific code.
In addition to H4 support, one key improvement is supporting not just
the "old" ARM debug LED API (with timer and idle LEDs, plus four that
can be handy for kernel debugging), but it also supports the "new"
generic LED API (most useful for usermode stuff IMO). Either or both
APIs can be enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add controller platform data
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Useful for debugging power management code.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add DMA IRQ sanity checks
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Minor GPIO cleanups: remove needless #include, and omap_gpio_init()
should be __init, as well as all the board init code calling it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add IRQF_IRQPOLL for each timer interrupt.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix oops in omap16xx mpuio suspend/resume code; field wasn't initialized
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GPIO and MPUIO wake updates:
- Hook MPUIOs into the irq wakeup framework too. This uses a platform
device to update irq enables during system sleep states, instead of
a sys_device, since the latter is no longer needed for such things.
- Also forward enable/disable irq wake requests to the relevant GPIO
controller, so the top level IRQ dispatcher can (eventually) handle
these wakeup events automatically if more than one GPIO pin needs to
be a wakeup event source.
- Minor tweak to the 24xx non-wakeup gpio stuff: no need to check such
read-only data under the spinlock.
This assumes (maybe wrongly?) that only 16xx can do GPIO wakeup; without
a 15xx I can't test such stuff.
Also this expects the top level IRQ dispatcher to properly handle requests
to enable/disable irq wake, which is currently known to be wrong: omap1
saves the flags but ignores them, omap2 doesn't even save it. (Wakeup
events are, wrongly, hardwired in the relevant mach-omapX/pm.c file ...)
So MPUIO irqs won't yet trigger system wakeup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Speedup and shrink GPIO irq handling code, by using a pointer
that's available in the irq_chip structure instead of calling
the get_gpio_bank() function. On OMAP1 this saves 44 words,
most of which were in IRQ critical path methods. Hey, every
few instructions help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds minimal OMAP2430 support to plat-omap files to
get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
More GPIO/IRQ cleanup:
- compile-time removal of much useless code
* mpuio support on non-OMAP1.
* 15xx/730/24xx gpio support on 1610
* 15xx/730/16xx gpio support on 24xx
* etc
- remove all BUG() calls, which are always bad news ... replaced some
with normal fault reports for that call, others with WARN_ON(1).
- small mpuio bugfix: add missing set_type() method
Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add some GPIO debug support: /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.
Includes minor bugfixes: recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable 24xx GPIO autoidling
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update OMAP1 to enable support for hrtimers and dynticks by using new clocksource and clockevent infrastructure.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Lots of places in arch/arm were needlessly including linux/ptrace.h,
resumably because we used to pass a struct pt_regs to interrupt
handlers. Now that we don't, all these ptrace.h includes are
redundant.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert 1510->15xx in generic omap code, so that sx1 can work.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When I went to use dmtimer7 it did not seem to work. I noticed that
the base addresses for dmtimers 7 and 8 were set wrong. A simple patch
to correct a small error. Confirmed to fix the problem on an OSK.
Signed-off-by: Matthew Percival <matthew@capgo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warnings
arch/arm/plat-omap/dmtimer.c: In function
'omap_dm_timer_modify_idlect_mask':
arch/arm/plat-omap/dmtimer.c:317: warning: no return
statement in function returning non-void
arch/arm/plat-omap/mailbox.c: In function 'omap_mbox_init':
arch/arm/plat-omap/mailbox.c:231: warning: ignoring return
value of 'class_device_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
No IRQF_TRIGGER set_type function for IRQ 353 (MPUIO)
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The register bits are reset by writing one. Remove the unneeded reads and
fix writes to not clear too many bits.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Standardize the miniscule percentage of occurrences of "depends" in
Kconfig files to "depends on", and update kconfig-language.txt to
reflect that.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Mostly clean up CONFIG_OMAP_RESET_CLOCKS. Also includes a
patch from Imre Deak to make McSPI clocks use id.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch syncs OMAP DMA code with linux-omap tree.
Mostly allow changing DMA callback function and set
OMAP2 specific transfer mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP2420, an incoming GPIO interrupt always sets both GPIO_IRQSTATUS1
and GPIO_IRQSTATUS2, even if the relevant bit is disabled in
GPIO_IRQENABLE1/2 and DSP doesn't use GPIO at all. GPIO_IRQSTATUS1
is for MPU and GPIO_IRQSTATUS2 is for DSP. If IRQSTATUS is set, this
will prevent the system from going to idle state. This patch also clears
IRQSTATUS2 to avoid the above situation.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPT1 will be set into non-posted mode, and the wakeup register
is set for all timers.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add enable/disable functions which effectively control the GPT iclk and fclk.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove Remove superfluous/recursive locking for GPIO
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch makes the OMAP2 dmtimers module using the interface
clocks only while the registers are accessed (except GPT1 which has
iclk enabled all the time).
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The recent MPUIO range change fix breaks compilation if
CONFIG_ARCH_OMAP24XX isn't defined; it should be OMAP_MAX_GPIO_LINES not
MAX_GPIO_LINES I believe. This one liner fixes it.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have to make sure that the LCD DMA external destination bit is
cleared by default, otherwise OMAP won't sleep.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- MPUIO doesn't exist on OMAP2
- no error was returned for too big MPUIO numbers
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP does not need sys_ck or sys_clkout. If the devices connected
to McBSP need sys_clkout, they need to request it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Apollon board MMC supports on OMAP2
TODO:
We have to check MMC on H4
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reprogramming takes places before putting the CPU into idle mode if
the dynamic tick option is enabled. The timer is then set to expire
at the next pending timer event. Because some time has already passed
since the last reported jiffy we have to wait less than the time
specified in jiffies.
Also make sure we don't set a load value of 0 whose outcome is
unspecified according to the TRM.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from David Brownell
ARM genirq cleanups/updates:
- Start switching platforms to newer APIs
* use "irq_chip" name, not "irqchip"
* providing irq_chip.name
- Show irq_chip.name in /proc/interrupts, like on x86.
This update a bit more than half of the ARM code. The irq_chip.name
values were chosen to match docs (if I have them) or be otherwise
obvious ("FPGA", "CPLD", or matching the code).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM devel merge introduced new machine functionality which was not
covered by the ARM -> genirq patches. Fix it up and make it compile
again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The irgflags consolidation did conflict with the ARM to generic IRQ
conversion and was not applied for ARM. Fix it up.
Use the new IRQF_ constants and remove the SA_INTERRUPT define
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (44 commits)
[ARM] 3541/2: workaround for PXA27x erratum E7
[ARM] nommu: provide a way for correct control register value selection
[ARM] 3705/1: add supersection support to ioremap()
[ARM] 3707/1: iwmmxt: use the generic thread notifier infrastructure
[ARM] 3706/2: ep93xx: add cirrus logic edb9315a support
[ARM] 3704/1: format IOP Kconfig with tabs, create more consistency
[ARM] 3703/1: Add help description for ARCH_EP80219
[ARM] 3678/1: MMC: Make OMAP MMC work
[ARM] 3677/1: OMAP: Update H2 defconfig
[ARM] 3676/1: ARM: OMAP: Fix dmtimers and timer32k to compile on OMAP1
[ARM] Add section support to ioremap
[ARM] Fix sa11x0 SDRAM selection
[ARM] Set bit 4 on section mappings correctly depending on CPU
[ARM] 3666/1: TRIZEPS4 [1/5] core
ARM: OMAP: Multiplexing for 24xx GPMC wait pin monitoring
ARM: OMAP: Fix SRAM to use MT_MEMORY instead of MT_DEVICE
ARM: OMAP: Update dmtimers
ARM: OMAP: Make clock variables static
ARM: OMAP: Fix GPMC compilation when DEBUG is defined
ARM: OMAP: Mux updates for external DMA and GPIO
...
Patch from Thomas Gleixner
From: Thomas Gleixner <tglx@linutronix.de>
Fixup the conversion to generic irq subsystem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch makes OMAP MMC work again:
- Fix compile errors
- Do not ioremap base as it is already statically mapped
- Clean-up platform device handling
- Fix compile warnings
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Fixes compilation errors on OMAP1. Patch from Timo Teras.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MT_MEMORY is needed in order to execute code in SRAM. Also
need to use section mapping.
Based on a patch by Richard Woodruff.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Initialize timer outside of spinlock to reduce the time the spinlock is held
- Do clk_get to the source clocks during initialization to avoid sleeping later
- New function to set counter register
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the mutex protecting the clock list is static, the list
itself should be too.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- DMA CSR register is cleared by reading on omap1, but on
omap2 it is cleard by writing to it.
- DMA TOUT interrupt does not exist on omap24xx, rename it
- Add SECURE and MISALIGNED errors by default for omap24xx
- Add defines for external DMA request lines
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dmtimer framework update broke 32 kHz timer as udelay() does not work
before system timer is started (and GPT1 should not be reset).
This also makes the GP timer use GPT1. This requires a fix in clock framework.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Port dmtimer framework to OMAP2.
Modify the dmtimers API to support setting of PWM configuration and prescaler.
Convert 32 kHz timer and GP timer to use the dmtimer framework.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The GPIO IRQ mask was retrieved incorrectly in cases where we have a mask
register instead of an enable register. Also we should only return the
valid bits depending on the bank size.
This fixes a bug on 1510/1610 based OMAPs where GPIO IRQs are not
delivered.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix for re-using OMAP DMA channel with different transfer parameters.
Bits in the CCR register need to be cleaned as well in some cases.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds core support for the TI F-Sample Board (OMAP 850).
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- The current OMAP GPIO IRQ framework doesn't use the do_edge_IRQ,
do_level_IRQ handlers, but instead calls do_simple_IRQ. This
doesn't handle disabled interrupts properly, so drivers will
still get interrupts after calling disable_irq. The patch solves
this by respecting the irq_desc.disable_depth and irq_desc.running
counters. When one of these is non-zero the handler is not called,
the interrupt is masked and marked as pending. The pending interrupt
will be serviced when the running handler returns. This is according
to the same semantics as the standard do_edge_IRQ and do_level_IRQ
handlers have, so one day we should use them instead of do_simple_IRQ.
- Process only interrupts that are not masked. The ISR may contain
pending interrupts that are masked these shouldn't be processed.
- Move the bank IRQ unmasking out of the IRQ dispatch loop. If there
are further iterations we shouldn't unmask it if there are level
triggered interrupts pending.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Lennert Buytenhek
A couple of platforms aren't using the right comparison type in their
timer interrupt handlers (as we're comparing two wrapping timestamps,
we need a bmi/bpl-type comparison, not an unsigned comparison) -- this
patch fixes them up.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Recent change to use both id and name when available was
not necessarily returning the right clock as it also searched
for clock name afterwards. This caused MMC to break on H2 and
H3 boards.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Remove unnecessary omap_nop_release() as noted by RMK.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs OMAP board support with linux-omap tree.
The highlights of the patch are:
- Add support for Nokia 770 by Juha Yrjola
- Add support for Samsung Apollon by Kyungmin Park
- Add support for Amstrad E3 videophone by Jonathan McDowell
- Remove board-netstar.c board support as requested by Ladislav Michl
- Do platform_device registration in board files by Komal Shah et al.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update misc OMAP core code from linux-omap tree:
- McBSP updates by Samuel Ortiz, Andrzej Zaborowski
- Whitespace cleanups by Ladislav Michl
- Other fixes by various linux-omap developers
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP framebuffer low-level init code from linux-omap tree
by Imre Deak.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP PM code from linux-omap tree:
- Move PM code from plat-omap to mach-omap1 and mach-omap2
by Tony Lindgren
- Add minimal PM support for omap24xx by Tony Lindgren and
Richard Woodruff
- Misc updates to omap1 PM code by Tuukka Tikkanen et al
- Updates to the SRAM code needed for PM and FB by Imre Deak
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP GPIO code from linux-omap tree:
- Fix omap16xx edge control by Juha Yrjola
- Support for additional omap16xx trigger modes by Dirk Behme
- Fix edge detection by Tony Lindgren et al.
- Better support for omap15xx and omap310 by Andrej Zaborowski
- Fix omap15xx interrupt bug by Petukhov Nikolay
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP timers from linux-omap tree. The highlights of the
patch are:
- Move timer32k code from mach-omap1 to plat-omap and make it
work also on omap24xx by Tony Lindgren
- Add support for dmtimer idle check for PM by Tuukka Tikkanen
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
Update OMAP clock framework from linux-omap tree.
The highlights of the patch are:
- Add support for omap730 clocks by Andrzej Zaborowski
- Fix compile warnings by Dirk Behme
- Add support for using dev id by Tony Lindgren and Komal Shah
- Move memory timings and PRCM into separate files by Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds the missing cache flushes to common low-level
init that are needed to access the IO region. These flushes
are normally done at the end of devicemaps_init(), but we
need to detect the OMAP core type early.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes OMAP clock framework to use clk_enable/disable
instead of clk_use/unuse as specified in include/linux/clk.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes OMAP clock framework to use clk_enable/disable
instead of clk_use/unuse as specified in include/linux/clk.h.
Instances of clk_use/unuse are renamed to clk_enable/disable,
and references clk_use/unuse are removed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The arm clock semaphores are strict mutexes, convert them to the new
mutex implementation
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ICC likes to complain about storage class not being first, GCC doesn't
care much (except for cases like "inline static").
have a hard time seeing how it could break anything.
Thanks to Gabriel A. Devenyi for pointing out
http://linuxicc.sourceforge.net/ which is what made me create this patch.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Serial port and framebuffer init improvments by Imre Deak
- Common omap pin mux framework by Tony Lindgren
- Common omap clock framework by Tony Lindren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I recently picked up my older work to remove unnecessary #includes of
sched.h, starting from a patch by Dave Jones to not include sched.h
from module.h. This reduces the number of indirect includes of sched.h
by ~300. Another ~400 pointless direct includes can be removed after
this disentangling (patch to follow later).
However, quite a few indirect includes need to be fixed up for this.
In order to feed the patches through -mm with as little disturbance as
possible, I've split out the fixes I accumulated up to now (complete for
i386 and x86_64, more archs to follow later) and post them before the real
patch. This way this large part of the patch is kept simple with only
adding #includes, and all hunks are independent of each other. So if any
hunk rejects or gets in the way of other patches, just drop it. My scripts
will pick it up again in the next round.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Deepak Saxena
OMAP map_desc.pfn conversion
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Clock updates by Tuukka Tikkanen, Juha Yrjola,
Daniel Petrini and Tony Lindgren
- DMA fixes by Imre Deak, Juha Yrjola and Daniel Petrini
- Add support to dual-mode hardware timers by Lauri Leukkunen
- GPIO support for 24xx by Paul Mundt
- GPIO wake-up support by Tony Lindgren
- Better GPIO interrupt handler to not lose interrupts by
Ralph Walden and Ladislav Michl
- Power Management updates by Tuukka Tikkanen
- Make Power Management code use new SRAM functions by
Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is part of Thomas Gleixner's generic IRQ patch, which converts
ARM to use the generic IRQ subsystem. Here, we wrap calls to
desc->handler() in an inline function, desc_handle_irq(). This
reduces the size of Thomas' patch since the changes become more
localised.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds minimal cpufreq support for OMAP
taking advantage of the clock framework.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch by various OMAP developers syncs the OMAP
specific arch files with the linux-omap tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch by various OMAP developers syncs the OMAP
specific arch files with the linux-omap tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch move common OMAP code from arch-omap to plat-omap
directory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch move common OMAP code from arch-omap to plat-omap
directory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Chandra Shekhar