To support sqhd, for initiators that are following the spec and
paying attention to sqhd vs their sqtail values:
- add sqhd to struct nvmet_sq
- initialize sqhd to 0 in nvmet_sq_setup
- rather than propagate the 0's-based qsize value from the connect message
which requires a +1 in every sqhd update, and as nothing else references
it, convert to 1's-based value in nvmt_sq/cq_setup() calls.
- validate connect message sqsize being non-zero per spec.
- updated assign sqhd for every completion that goes back.
Also remove handling the NULL sq case in __nvmet_req_complete, as it can't
happen with the current code.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
fc transport is treating NVMET_NR_QUEUES as maximum queue count, e.g.
admin queue plus NVMET_NR_QUEUES-1 io queues. But NVMET_NR_QUEUES is
the number of io queues, so maximum queue count is really
NVMET_NR_QUEUES+1.
Fix the handling in the target fc transport
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The FC-NVME transport loopback test module used the FC-specific error
codes in cases where it emulated a transport abort case. Instead of
using the FC-specific values, now use a generic value (NVME_SC_INTERNAL).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The FC-NVME target transport used the FC-specific error codes in
return codes when the transport or lldd failed. Instead of using the
FC-specific values, now use a generic value (NVME_SC_INTERNAL).
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull followup block layer updates from Jens Axboe:
"I ended up splitting the main pull request for this series into two,
mainly because of clashes between NVMe fixes that went into 4.13 after
the for-4.14 branches were split off. This pull request is mostly
NVMe, but not exclusively. In detail, it contains:
- Two pull request for NVMe changes from Christoph. Nothing new on
the feature front, basically just fixes all over the map for the
core bits, transport, rdma, etc.
- Series from Bart, cleaning up various bits in the BFQ scheduler.
- Series of bcache fixes, which has been lingering for a release or
two. Coly sent this in, but patches from various people in this
area.
- Set of patches for BFQ from Paolo himself, updating both
documentation and fixing some corner cases in performance.
- Series from Omar, attempting to now get the 4k loop support
correct. Our confidence level is higher this time.
- Series from Shaohua for loop as well, improving O_DIRECT
performance and fixing a use-after-free"
* 'for-4.14/block-postmerge' of git://git.kernel.dk/linux-block: (74 commits)
bcache: initialize dirty stripes in flash_dev_run()
loop: set physical block size to logical block size
bcache: fix bch_hprint crash and improve output
bcache: Update continue_at() documentation
bcache: silence static checker warning
bcache: fix for gc and write-back race
bcache: increase the number of open buckets
bcache: Correct return value for sysfs attach errors
bcache: correct cache_dirty_target in __update_writeback_rate()
bcache: gc does not work when triggering by manual command
bcache: Don't reinvent the wheel but use existing llist API
bcache: do not subtract sectors_to_gc for bypassed IO
bcache: fix sequential large write IO bypass
bcache: Fix leak of bdev reference
block/loop: remove unused field
block/loop: fix use after free
bfq: Use icq_to_bic() consistently
bfq: Suppress compiler warnings about comparisons
bfq: Check kstrtoul() return value
bfq: Declare local functions static
...
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
- Lots of hfi1 driver updates (mixed with a few qib and core updates as
well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so we
can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@
-----BEGIN PGP SIGNATURE-----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=2ntC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
And fix the Get/Set Log Page implementation to take all 8 bits of the
feature identifier into account.
Signed-off-by: Omri Mann <omri@excelero.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[hch: used the UUID API, updated changelog]
This changes the earlier patch "nvmet: don't report 0-bytes
in serial number" to use the memcpy_and_pad() helper introduced
in a previous patch.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimbeg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The existing nvmet_fc sg list handling has 2 faults:
a) the request between LLDD and transport has too large of an sg
list (256 elements), which is normally 256k (64 elements).
b) sglist handling doesn't optimize on the fact that each element
is a page.
This patch removes the static sg list in the request and uses the
dynamic list already present in the nvmet_fc transport. It also
simplies the handling of the sg list on multiple sequences to
take advantage of the per-page divisions.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvmf target shall return NVME_SC_CONNECT_INVALID_HOST instead of
the gereal code INVALID_PARAM when the given host nqn is not allowed
to connect. Refer to the 2.2.1 section of the NVMe over Fabrics Spec.
Signed-off-by: Guan Junxiong <guanjunxiong@huawei.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that its not needed, we can simply not assign it.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There were 2 statics introduced that were bogus. Removed the static
designations.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use list_for_each_entry_safe to prevent list handling from referencing
next pointers directly after list_del's
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The merged version of my patch "nvmet: don't report 0-bytes in serial
number" fails to remove two lines which should have been replaced,
so that the space-padded strings are overwritten again with 0-bytes.
Fix it.
Fixes: 42de82a8b5 nvmet: don't report 0-bytes in serial number
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimbeg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
At queue creation, the transport allocates a local job struct
(struct nvmet_fc_fcp_iod) for each possible element of the queue.
When a new CMD is received from the wire, a jobs struct is allocated
from the queue and then used for the duration of the command.
The job struct contains buffer space for the wire command iu. Thus,
upon allocation of the job struct, the cmd iu buffer is copied to
the job struct and the LLDD may immediately free/reuse the CMD IU
buffer passed in the call.
However, in some circumstances, due to the packetized nature of FC
and the api of the FC LLDD which may issue a hw command to send the
wire response, but the LLDD may not get the hw completion for the
command and upcall the nvmet_fc layer before a new command may be
asynchronously received on the wire. In other words, its possible
for the initiator to get the response from the wire, thus believe a
command slot free, and send a new command iu. The new command iu
may be received by the LLDD and passed to the transport before the
LLDD had serviced the hw completion and made the teardown calls for
the original job struct. As such, there is no available job struct
available for the new io. E.g. it appears like the host sent more
queue elements than the queue size. It didn't based on it's
understanding.
Rather than treat this as a hard connection failure queue the new
request until the job struct does free up. As the buffer isn't
copied as there's no job struct, a special return value must be
returned to the LLDD to signify to hold off on recycling the cmd
iu buffer. And later, when a job struct is allocated and the
buffer copied, a new LLDD callback is introduced to notify the
LLDD and allow it to recycle it's command iu buffer.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The FC-NVME spec hasn't locked down on the format string for TRADDR.
Currently the spec is lobbying for "nn-<16hexdigits>:pn-<16hexdigits>"
where the wwn's are hex values but not prefixed by 0x.
Most implementations so far expect a string format of
"nn-0x<16hexdigits>:pn-0x<16hexdigits>" to be used. The transport
uses the match_u64 parser which requires a leading 0x prefix to set
the base properly. If it's not there, a match will either fail or return
a base 10 value.
The resolution in T11 is pushing out. Therefore, to fix things now and
to cover any eventuality and any implementations already in the field,
this patch adds support for both formats.
The change consists of replacing the token matching routine with a
routine that validates the fixed string format, and then builds
a local copy of the hex name with a 0x prefix before calling
the system parser.
Note: the same parser routine exists in both the initiator and target
transports. Given this is about the only "shared" item, we chose to
replicate rather than create an interdendency on some shared code.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The NVME standard mandates that the SN, MN, and FR fields of the Identify
Controller Data Structure be "ASCII strings". That means that they may
not contain 0-bytes, not even string terminators.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
[hch: fixed for the move of the serial field, updated description]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe target has no way to preserve controller serial
IDs across reboots which breaks udev scripts doing
SYMLINK+="dev/disk/by-id/nvme-$env{ID_SERIAL}-part%n.
Export the randomly generated serial number via configfs and allow
setting of a serial via configfs to mitigate this breakage.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe specification defines the serial number as:
"Serial Number (SN): Contains the serial number for the NVM subsystem
that is assigned by the vendor as an ASCII string. Refer to section
7.10 for unique identifier requirements. Refer to section 1.5 for ASCII
string requirements"
So move it from the controller to the subsystem, where it belongs.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The NVMe target's attribute files need an attr prefix in order to have
nvmetcli recognize them. Add this attribute.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We always need to do non-equal comparisms on the native endian versions
to get the correct result.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We actually using the cookie returned from the last submit_bio
call.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Target validation of the Create Association LS revised to accept any
LS as long as all non-pad data has been received. This allows a (newer)
target to accept the LS from older initiators with varying pad lengths.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Usually before we teardown the controller we want to:
1. complete/cancel any ctrl inflight works
2. remove ctrl namespaces (only for removal though, resets
shouldn't remove any namespaces).
but we do not want to destroy the controller device as
we might use it for logging during the teardown stage.
This patch adds nvme_start_ctrl() which queues inflight
controller works (aen, ns scan, queue start and keep-alive
if kato is set) and nvme_stop_ctrl() which cancels the works
namespace removal is left to the callers to handle.
Move nvme_uninit_ctrl after we are done with the
controller device.
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
unlike blk_mq_stop_hw_queues and blk_mq_start_stopped_hw_queues
quiescing/unquiescing respects the submission path rcu grace.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
We might have more/less queues once we reconnect/reset. For
example due to cpu going online/offline
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
All transports use either a private cache of controller cap or an on-stack
copy, move it to the generic struct nvme_ctrl. In the future it will also
be maintained by the core.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
All all transports use the queue_count in exactly the same, so move it to
the generic struct nvme_ctrl. In the future it will also be maintained by
the core.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-By: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
We can deadlock in case we got to a device removal
event on a queue which is already in the process of
destroying the cm_id is this is blocking until all
events on this cm_id will drain. On the other hand
we cannot guarantee that rdma_destroy_id was invoked
as we only have indication that the queue disconnect
flow has been queued (the queue state is updated before
the realease work has been queued).
So, we leave all the queue removal to a separate ib_client
to avoid this deadlock as ib_client device removal is in
a different context than the cm_id itself.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Tested-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
if a nvme command is issued with an opcode that is not supported by
the target (example: opcode 21 - detach namespace), the target
crashes due to a null pointer.
nvmet_req_init() detects the bad opcode and immediately calls the nvme
command done routine with an error status, allowing the transport to
send the response. However, the FC transport was aborting the command
on error, so the abort freed the lldd point, but the rsp transmit path
referenced it psot the free.
Fix by removing the abort call on nvmet_req_init() failure.
The completion response will be sent with an error status code.
As the completion path will terminate the io, ensure the data_sg
lists show an unused state so that teardown paths are successful.
Signed-off-by: Paul Ely <Paul.Ely@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
NVMe 1.2.1 or later requires controllers to provide a subsystem NQN in the
Identify controller data structures. Use this NQN for the subsysnqn
sysfs attribute by storing it in the nvme_ctrl structure after verifying
it. For older controllers we generate a "fake" NQN per non-normative
text in the NVMe 1.3 spec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No need to differentiate fabrics from pci/loop, also lower
it to 32 as we don't really need 256 inflight admin commands.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This moves the nvme_reset function from the PCIe driver to common code,
renaming it to nvme_reset_ctrl in the process. Additionally a new
helper nvme_reset_ctrl_sync is added for the case where we want to
wait for the reset. To facilitate that the reset_work work structure is
move to the common nvme_ctrl structure and the ->reset_ctrl method is
removed. For now the drivers initialize the reset_work with their own
callback, but longer term we should move to callouts for specific
parts of the reset process and move even more code to the core.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Now that we get the tagset passed we can have a single implementation for
the I/O and admin queues.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This was detected by building the nvmet-fc driver with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Allow overriding the announced NVMe Version of a via configfs.
This is particularly helpful when debugging new features for the host
or target side without bumping the hard coded version (as the target
might not be fully compliant to the announced version yet).
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Guan Junxiong <guanjunxiong@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add the UUID field from the NVMe Namespace Identification Descriptor
to the nvmet_ns structure and allow it's population via configfs.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A NVMe Identify NS command with a CNS value of '3' is expecting a list
of Namespace Identification Descriptor structures to be returned to
the host for the namespace requested in the namespace identify
command.
This Namespace Identification Descriptor structure consists of the
type of the namespace identifier, the length of the identifier and the
actual identifier.
Valid types are NGUID and UUID which we have saved in our nvme_ns
structure if they have been configured via configfs. If no value has
been assigened to one of these we return an "invalid opcode" back to
the host to maintain backward compatibiliy with older implementations
without Namespace Identify Descriptor list support.
Also as the Namespace Identify Descriptor list is the only mandatory
feature change between 1.2.1 and 1.3 we can bump the advertised
version as well.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use NVME_IDENTIFY_DATA_SIZE define instead of hard coding the magic
4096 value.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.com>
[hch: converted three more users]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of each transport using it's own workqueue, export
a single nvme-core workqueue and use that instead.
In the future, this will help us moving towards some unification
if controller setup/teardown flows.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Use the same values for use for request completion errors as the return
value from ->queue_rq. BLK_STS_RESOURCE is special cased to cause
a requeue, and all the others are completed as-is.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
So that we can have more flags for transport-specific behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
On rdma read errors, release the sq ref that was taken
when the req was initialized. This avoids a hang in
nvmet_sq_destroy() when the queue is being freed.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove the request_idx parameter, which can't be used safely now that we
support I/O schedulers with blk-mq. Except for a superflous check in
mtip32xx it was unused anyway.
Also pass the tag_set instead of just the driver data - this allows drivers
to avoid some code duplication in a follow on cleanup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Christoph writes:
"A couple more updates for 4.12. The biggest pile is fc and lpfc
updates from James, but there are various small fixes and cleanups as
well."
Fixes up a few merge issues, and also a warning in
lpfc_nvmet_rcv_unsol_abort() if CONFIG_NVME_TARGET_FC isn't enabled.
Signed-off-by: Jens Axboe <axboe@fb.com>
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
That's what it's used as.
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
The passed in desc_len is a big endian value, so mark it as such.
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Found by sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
The FC-NVME spec revised syntax to avoid comma separators.
Sync with the change in the parser for traddr on port attachments.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
target transport:
----------------------
There are cases when there is a need to abort in-progress target
operations (writedata) so that controller termination or errors can
clean up. That can't happen currently as the abort is another target
op type, so it can't be used till the running one finishes (and it may
not). Solve by removing the abort op type and creating a separate
downcall from the transport to the lldd to request an io to be aborted.
The transport will abort ios on queue teardown or io errors. In general
the transport tries to call the lldd abort only when the io state is
idle. Meaning: ops that transmit data (readdata or rsp) will always
finish their transmit (or the lldd will see a state on the
link or initiator port that fails the transmit) and the done call for
the operation will occur. The transport will wait for the op done
upcall before calling the abort function, and as the io is idle, the
io can be cleaned up immediately after the abort call; Similarly, ios
that are not waiting for data or transmitting data must be in the nvmet
layer being processed. The transport will wait for the nvmet layer
completion before calling the abort function, and as the io is idle,
the io can be cleaned up immediately after the abort call; As for ops
that are waiting for data (writedata), they may be outstanding
indefinitely if the lldd doesn't see a condition where the initiatior
port or link is bad. In those cases, the transport will call the abort
function and wait for the lldd's op done upcall for the operation, where
it will then clean up the io.
Additionally, if a lldd receives an ABTS and matches it to an outstanding
request in the transport, A new new transport upcall was created to abort
the outstanding request in the transport. The transport expects any
outstanding op call (readdata or writedata) will completed by the lldd and
the operation upcall made. The transport doesn't act on the reported
abort (e.g. clean up the io) until an op done upcall occurs, a new op is
attempted, or the nvmet layer completes the io processing.
fcloop:
----------------------
Updated to support the new target apis.
On fcp io aborts from the initiator, the loopback context is updated to
NULL out the half that has completed. The initiator side is immediately
called after the abort request with an io completion (abort status).
On fcp io aborts from the target, the io is stopped and the initiator side
sees it as an aborted io. Target side ops, perhaps in progress while the
initiator side is done, continue but noop the data movement as there's no
structure on the initiator side to reference.
patch also contains:
----------------------
Revised lpfc to support the new abort api
commonized rsp buffer syncing and nulling of private data based on
calling paths.
errors in op done calls don't take action on the fod. They're bad
operations which implies the fod may be bad.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Current design has the fcloop job struct, used for both initiator and
target processing, allocated as part of the initiator request structure.
On aborts, the initiator side (based on the request) may terminate, yet
the target side wants to continue processing. the target side can't do
that if the initiator side goes away.
Revise fcloop to allocate an independent target side structure when it
starts an io from the initiator.
Added a lock to the request struct as well to synchronize pointer updates
on abort calls.
Modified target downcalls to recognize conditions where initiator has
aborted the io (thus nulled the pointer between job structs), thus
avoid referencing sgl lists which are gone and no longer making upcalls
to the initiator.
In conditions where the targetport is no longer connected, have the
initiator return an access failure rather than simulating a command
completion.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
With the advent of the opdone calls changing context, the lldd can no
longer assume that once the op->done call returns for RSP operations
that the request struct is no longer being accessed.
As such, revise the lldd api for a req_release callback that the
transport will call when the job is complete. This will also be used
with abort cases.
Fixed text in api header for change in io complete semantics.
Revised lpfc to support the new req_release api.
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Two new feature flags were added to control whether upcalls to the
transport result in context switches or stay in the calling context.
NVMET_FCTGTFEAT_CMD_IN_ISR:
By default, if the flag is not set, the transport assumes the
lldd is in a non-isr context and in the cpu context it should be
for the io queue. As such, the cmd handler is called directly in the
calling context.
If the flag is set, indicating the upcall is an isr context, the
transport mandates a transition to a workqueue. The workqueue assigned
to the queue is used for the context.
NVMET_FCTGTFEAT_OPDONE_IN_ISR
By default, if the flag is not set, the transport assumes the
lldd is in a non-isr context and in the cpu context it should be
for the io queue. As such, the fcp operation done callback is called
directly in the calling context.
If the flag is set, indicating the upcall is an isr context, the
transport mandates a transition to a workqueue. The workqueue assigned
to the queue is used for the context.
Updated lpfc for flags
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
This is safer as it doesn't rely on the data being stored in
a single page in an sgl.
It also aids our effort to start phasing out users of sg_page. See [1].
For this we kmalloc some memory, copy to it and free at the end. Note:
we can't allocate this memory on the stack as the kbuild test robot
reports some frame size overflows on i386.
[1] https://lwn.net/Articles/720053/
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
We want our own clearly defined error field for NVMe passthrough commands,
and the request errors field is going away in its current form.
Just store the status and result field in the nvme_request field from
hardirq completion context (using a new helper) and then generate a
Linux errno for the block layer only when we actually need it.
Because we can't overload the status value with a negative error code
for cancelled command we now have a flags filed in struct nvme_request
that contains a bit for this condition.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
both our sqsize and the controller MQES cap are a 0 based value,
so making it 1 based is wrong.
Reported-by: Trapp, Darren <Darren.Trapp@cavium.com>
Reported-by: Daniel Verkamp <daniel.verkamp@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Turn the existing discard flag into a new BLKDEV_ZERO_UNMAP flag with
similar semantics, but without referring to diѕcard.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We've added a considerable amount of fixes for stalls and issues
with the blk-mq scheduling in the 4.11 series since forking
off the for-4.12/block branch. We need to do improvements on
top of that for 4.12, so pull in the previous fixes to make
our lives easier going forward.
Signed-off-by: Jens Axboe <axboe@fb.com>
This avoids duplicating the logic four times, and it also allows to keep
some helpers static in core.c or just opencode them.
Note that this loses printing the aborted status on completions in the
PCI driver as that uses a data structure not available any more.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This way our max retry limit holds as well.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Clear SG list to avoid double frees of payload page list
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
if nvmf_register_transport happend to fail, we
need to nvmet_unregister_transport as well.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch introduces helper function for checking controller
status during admin and io command processing which returns u16
status. As to bring consistency on returning status, other
friend functions also now return u16 status instead of int
to match the spec.
As part of the theseerror log prints in also prints qid on
which command error occured.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of parsing address strings, use a generic
helper. This also adds ipv6 (with address scopes)
support.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If we are attacked with establishments/teradowns we need to
make sure we do not consume too much system memory. Thus
let ongoing controller teardowns complete before accepting
new controller establishments.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
When handling a new recv command, we grab a new rsp resource and
check for the queue state being live. In case the queue is not in
live state, we simply restore the rsp back to the free list. However
in this flow we didn't set rsp->queue yet, so we cannot dereference it.
Instead, make sure to initialize rsp->queue (and other rsp members)
as soon as possible so we won't reference uninitialized variables.
Reported-by: Yi Zhang <yizhan@redhat.com>
Reported-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
percpu_ref_kill is not enough to prevent subsequent
percpu_ref_tryget_live from failing. Hence call
perfcpu_ref_kill_confirm to make it safe.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a cpu unplug event has occured, we need to take the minimum
of the provided nr_io_queues and the number of online cpus,
otherwise we won't be able to connect them as blk-mq mapping
won't dispatch to those queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
we need to destroy the nvmet sq and let it finish gracefully
before continue to cleanup the queue.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
We need to do arithmetics after byte swapping, not before.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
The length field in the Write Zeroes command is a 16-bit field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
In this case entirely harmless as it's all-ones, but still nice to
shut up sparse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Constify all instances of blk_mq_ops, as they are never modified.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a cpu unplug event has occured, we need to take the minimum
of the provided nr_io_queues and the number of online cpus,
otherwise we won't be able to connect them as blk-mq mapping
won't dispatch to those queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
When handling a new recv command, we grab a new rsp resource and
check for the queue state being live. In case the queue is not in
live state, we simply restore the rsp back to the free list. However
in this flow we didn't set rsp->queue yet, so we cannot dereference it.
Instead, make sure to initialize rsp->queue (and other rsp members)
as soon as possible so we won't reference uninitialized variables.
Reported-by: Yi Zhang <yizhan@redhat.com>
Reported-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
percpu_ref_kill is not enough to prevent subsequent
percpu_ref_tryget_live from failing. Hence call
perfcpu_ref_kill_confirm to make it safe.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
we need to destroy the nvmet sq and let it finish gracefully
before continue to cleanup the queue.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
We don't actually need the full rculist.h header in sched.h anymore,
we will be able to include the smaller rcupdate.h header instead.
But first update code that relied on the implicit header inclusion.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
James Smart