If one disables DDR DVFS in the BIOS, Punit will apparently ignores
all DDR DVFS request. Currently we assume that DDR DVFS is always
operational, which leads to errors in dmesg when the DDR DVFS requests
time out.
Fix the problem by gently prodding Punit during driver load to find out
whether it will respond to DDR DVFS requests. If the request times out,
we assume that DDR DVFS has been permanenly disabled in the BIOS and
no longer perster the Punit about it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91629
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In I915_READ64_2x32 we attempt to read a 64bit register using 2 32bit
reads. Due to the nature of the registers we try to read in this manner,
they may increment between the two instruction (e.g. a timestamp
counter). To keep the result accurate, we repeat the read if we detect
an overflow (i.e. the upper value varies). However, some hardware is just
plain flaky and may endless loop as the the upper 32bits are not stable.
Just give up after a couple of tries and report whatever we read last.
v2: Use the most recent values when erring out on an unstable register.
Reported-by: russianneuromancer@ya.ru
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91906
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
From B spec, DDI_E port belong to PowerWell 2, but
DDI_E share the powerwell_req/staus register bit with
DDI_A which belong to DDI_A_E_POWER_WELL.
In order to communicate with the connector on DDI-E, both
DDI_A_E_POWER_WELL and POWER_WELL_2 must be enabled.
Currently intel_dp_power_get(DDI_E) only enable
DDI_A_E_POWER_WELL, this patch will not only enable
DDI_a_E_POWER_WELL but also enable POWER_WELL_2.
This patch also fix the DDI-E hotplug function.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
DDI-E doesn't have the correspondent GMBUS pin.
We rely on VBT to tell us which one it being used instead.
The DVI/HDMI on shared port couldn't exist.
This patch isn't tested without hardware wchich has HDMI
on DDI-E.
v2: fix trailing whitespace
v3: MISSING_CASE take place of BUG()
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
v2: fix one error found by checkpath.pl
v3: Add one ignored break for switch-case. DDI-E hotplug
function doesn't work after updating drm-intel tree,
I checked the code and found this missing which isn't
the root cause for broke DDI-E hp. The broken
DDI-E hp function is fixed by "Adding DDI_E power
well domain".
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Tested-by: Timo Aaltonen <timo.aaltonen@canonical.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bunch more fixes for 4.3, most of it skl fallout. It's not quite all yet,
there's still a few more patches pending to enable DDI-E correctly on skl.
Also included the dpms atomic work from Maarten since atomic is just a
pain and not including would cause piles of conflicts right from the
start.
* tag 'drm-intel-next-fixes-2015-08-16' of git://anongit.freedesktop.org/drm-intel: (67 commits)
drm/i915: Per-DDI I_boost override
drm/i915/skl: WaIgnoreDDIAStrap is forever, always init DDI A
drm/i915: fix checksum write for automated test reply
drm/i915: Contain the WA_REG macro
drm/i915: Remove the failed context from the fpriv->context_idr
drm/i915: Report IOMMU enabled status for GPU hangs
drm/i915: Check idle to active before processing CSQ
drm/i915: Set alternate aux for DDI-E
drm/i915: Set power domain for DDI-E
drm/i915: fix stolen bios_reserved checks
drm/i915: Use masked write for Context Status Buffer Pointer
drm/i915/skl WaDisableSbeCacheDispatchPortSharing
drm/i915: Spam less on dp aux send/receive problems
drm/i915: Handle return value in intel_pin_and_fence_fb_obj, v2.
drm/i915: Only update mode related state if a modeset happened.
drm/i915: Remove connectors_active.
drm/i915: Remove connectors_active from intel_dp.c, v2.
drm/i915: Remove connectors_active from sanitization, v2.
drm/i915: Get rid of dpms handling.
drm/i915: Make crtc checking use the atomic state, v2.
...
An OEM may request increased I_boost beyond the recommended values
by specifying an I_boost value to be applied to all swing entries for
a port. These override values are specified in VBT.
v2: rebase and remove unused iboost_bit variable
Issue: VIZ-5676
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge drm-intel-fixes because a bunch of atomic patch backporting
we had to do lead to horrible conflicts.
Conflicts:
drivers/gpu/drm/drm_crtc.c
Just a bit of context conflict between -next and -fixes.
drivers/gpu/drm/i915/intel_atomic.c
drivers/gpu/drm/i915/intel_display.c
Atomic conflicts, always pick the code from -next.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The IOMMU for Intel graphics has historically had many issues resulting
in random GPU hangs. Lets include its status when capturing the GPU hang
error state for post-mortem analysis.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no correspondent Aux channel for DDI-E.
So we need to rely on VBT to let us know witch one
is being used instead.
v2: Removing some trailing spaces and giving proper
credit to Xiong that added a nice way to avoid port
conflicts by setting supports_dp = 0 when using
equivalent aux for DDI-E.
Credits-to: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch contains the changes to remove the byte
swapping logic introduced with old dmc firmware.
While debugging PC10 entry issue for skylake found
with latest dmc firmware version 1.18 without byte
swapping dmc is working fine and able to enter PC10.
Note that apparently this was changed with dmc version 1.0 and earlier
ones indeed are byteswapped like this ...
v1: Initial version.
v2: Corrected firmware size during memcpy(). (Suggested by Sunil)
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: A.Sunil Kamath <sunil.kamath@intel.com>
[danvet: Add note that this only holds for released dmc firmware.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First, an introduction. We currently have two types of GTT mmaps: the
"normal" old mmap, and the WC mmap. For frontbuffer-related features
that have automatic hardware tracking, only the non-WC mmap writes are
detected by the hardware. Since inside the Kernel both are treated as
ORIGIN_GTT, any features ignoring ORIGIN_GTT because of the hardware
tracking are destined to fail.
One of the special rules defined for the WC mmaps is that the user
should call the dirtyfb IOCTL after he is done using the pointers, so
that results in an intel_fb_obj_flush() call. The problem is that the
dirtyfb is passing ORIGIN_GTT, so it is being ignored by FBC - even
though the hardware tracking is not detecing the WC mmap operations.
So in order to fix that without having to give up the automatic
hardware tracking for GTT mmaps we transform the flush operation from
dirtyfb into a special operation: ORIGIN_DIRTYFB.
This commit fixes all the kms_frontbuffer_tracking subtests that
contain "fbc" and "mmap-wc" in their names and are currently failing
(for a total of 16 subtests).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we may conceivably encounter situations where the upper part of the
64bit register changes between reads, for example when a timestamp
counter overflows, change the WARN into a retry loop.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove the leftovers, yay!
AGP for i915 kms died long ago with
commit 3bb6ce6686
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Nov 13 22:14:16 2013 +0100
drm/i915: Kill legeacy AGP for gen3 kms
and with ums now gone to there's really no users any more.
Note that device_is_agp is only called when DRIVER_USE_AGP is set and
since we've unconditionally cleared that since a while there are
really no users left for i915_driver_device_is_agp.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
It fits more with the low-level fence code, and this move leaves only
the userspace tiling ioctl handling in i915_gem_tiling.c.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
No code changes, just moving all the fence related code into a
separate file (and avoiding a bunch of forward declarations while at
it).
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Currently HPD_PORT_A is used as an alias for HPD_NONE to mean that the
given port doesn't support long/short HPD pulse detection. SDVO and CRT
ports are like this and for these ports we only want to know whether an
hot plug event was detected on the corresponding pin. Since at least on
BXT we need long/short pulse detection on PORT A as well (added by the
next patch) remove this aliasing of HPD_PORT_A/HPD_NONE and let the
return value of intel_hpd_pin_to_port() show whether long/short pulse
detection is supported on the passed in pin.
No functional change.
v2:
- rebase on top of -nightly (Daniel)
- make the check for intel_hpd_pin_to_port() return value more readable
(Sivakumar)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two new module parameters: "enable_guc_submission" which will turn
on submission of batchbuffers via the GuC (when implemented), and
"guc_log_level" which controls the level of debugging logged by the
GuC and captured by the host.
Signed-off-by: Alex Dai <yu.dai@intel.com>
v4:
Mark "enable_guc_submission" unsafe [Daniel Vetter]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915_gem_object_create_from_data() is a generic function to save data
from a plain linear buffer in a new pageable gem object that can later
be accessed by the CPU and/or GPU.
We will need this for the microcontroller firmware loading support code.
Derived from i915_gem_object_write(), originally by Alex Dai
v2:
Change of function: now allocates & fills a new object, rather than
writing to an existing object
New name courtesy of Chris Wilson
Explicit domain-setting and other improvements per review comments
by Chris Wilson & Daniel Vetter
v4:
Rebased
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backmerge fixes since it's getting out of hand again with the massive
split due to atomic between -next and 4.2-rc. All the bugfixes in
4.2-rc are addressed already (by converting more towards atomic
instead of minimal duct-tape) so just always pick the version in next
for the conflicts in modeset code.
All the other conflicts are just adjacent lines changed.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
drivers/gpu/drm/i915/intel_ringbuffer.h
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Huzzah! \o/
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Updated the HAS_CORE_RING_FREQ macro to add the broxton check,
so as to disallow the programming & read of ring frequency
table for it.
Issue: VIZ-5144
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added a new HAS_CORE_RING_FREQ macro, currently used in
gen6_update_ring_freq & i915_ring_freq_table debugfs function.
The programming & read of ring frequency table is needed for newer
GEN(>=6) platforms, except VLV/CHV.
Issue: VIZ-5144
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of all the ad-hoc updating, duplicate the old state first
before reading out the hw state, then restore it.
intel_display_resume is a new function that duplicates the sw state,
then reads out the hw state, and commits the old state.
intel_display_setup_hw_state now only reads out the atomic state.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=90396
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the previous patch this flag will check always clear, as it's
never set for shmem backed and userptr objects, so we can remove it.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Yeah this isn't really fixes but it's a nice cleanup to
clarify the code but not really worth the hassle of backmerging. So
just add to -fixes, we're still early in -rc.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This broken code was introduced in
commit aa7471d228
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 1 11:15:21 2015 +0300
drm/i915: add i915 specific connector debugfs file for DPCD
v2: Drop hunk that accidentally crept in.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: François Valenduc <francoisvalenduc@gmail.com>
Reported-by: François Valenduc <francoisvalenduc@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The poor in_dbg_master() check was the only one without a reason
string. Give it a reason string so it won't feel excluded.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is all internal i915.ko work, let's start using intel_crtc for
everything.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the cool kids use dev_priv and FBC wants to be cool too.
We've been historically using struct drm_device on the FBC function
arguments, but we only really need it for intel_vgpu_active(): we can
use dev_priv everywhere else. So let's fully switch to dev_priv since
I'm getting tired of adding "struct drm_device *dev = dev_priv->dev"
everywhere.
If I get a NACK here I'll propose the opposite: convert all the
functions that currently take dev_priv to take dev.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because it makes more sense there, IMHO.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After the register save/restore code is gone there's just one user
left and it just obfuscates that one. Remove it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since that's really what we want to test for. Note remove the gen5
case doesn't change anything: In intel_setup_outputs ilk is handled
already in the HAS_PCH_SPLIT case, and the register save/restore code
touches registers which simply doesn't exist anymore at all.
v2: Drop UMS parts.
v3: Update commit message to reflect that the reg save/restore code is
gone (Ville).
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we're not going to have weird races in really weird cases
where a lot of different CRTCs are doing rendering and modesets at the
same time.
With this change and the stolen_lock from the previous patch, we can
start removing the struct_mutex locking we have around FBC in the next
patches.
v2:
- Rebase (6 months later)
- Also lock debugfs and stolen.
v3:
- Don't lock a single value read (Chris).
- Replace lockdep assertions with WARNs (Daniel).
- Improve commit message.
- Don't forget intel_pre_plane_update() locking.
v4:
- Don't remove struct_mutex at intel_pre_plane_update() (Chris).
- Add comment regarding locking dependencies (Chris).
- Rebase after the stolen code rework.
- Rebase again after drm-intel-nightly changes.
v5:
- Rebase after the new stolen_lock patch.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Which should protect dev_priv->mm.stolen usage. This will allow us to
simplify the relationship between stolen memory, FBC and struct_mutex.
v2:
- Rebase after the stolen_remove_node() dev_priv patch move.
- I realized that after we fixed a few things related to the FBC CFB
size checks, we're not reallocating the CFB anymore with FBC
enabled, so we can just move all the locking to i915_gem_stolen.c
and stop worrying about freezing all the stolen alocations while
freeing/rellocating the CFB. This allows us to fix the "Too
coarse" observation from Chris.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the abstractions created by the last patch, we can move this code
and the only thing inside intel_fbc.c that knows about dev_priv->mm is
the code that reads stolen_base.
We also had to move a call to i915_gem_stolen_cleanup_compression()
- now called intel_fbc_cleanup_cfb() - outside i915_gem_stolen.c.
v2:
- Rebase after the remove_node() changes on the previous patch.
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We want to move the FBC code out of i915_gem_stolen.c, but that code
directly adds/removes stolen memory nodes. Let's create this
abstraction, so i915_gme_stolen.c is still in control of all the
stolen memory handling. The abstraction will also allow us to add
locking assertions later.
v2:
- Add dev_priv as remove_node() argument since we'll need it later
(Chris).
Requested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ensures that the batch buffer is executed by the resource streamer.
And will let userspace know whether Resource Streamer is supported in
the kernel.
v2: Don't skip 1<<15 for the exec flags (Jani Nikula)
v3: Use HAS_RESOURCE_STREAMER macro for execbuf validation (Chris Wilson)
(from getparam patch)
v2: Update I915_PARAM_HAS_RESOURCE_STREAMER so it's after
I915_PARAM_HAS_GPU_RESET.
v3: Only advertise RS support for hardware that supports it.
v4: Add HAS_RESOURCE_STREAMER() macro (Chris)
Testcase: igt/gem_exec_params
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
[danvet: squash in getparam patch since it'd break bisect, suggested
by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although we have a fixed setting for the PLL9 and EBB4 registers, it
still makes sense to check them together with the rest of PLL registers.
While at it also remove a redundant comment about 10 bit clock enabling.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch adds support for 0.85V VccIO on Skylake Y,
separate buffer translation tables for Skylake U,
and support for I_boost for the entries that needs this.
Changes in v2:
* Refactored the code a bit to move all DDI signal level setup to
intel_ddi.c
Issue: VIZ-5677
Signed-off-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
[danvet: Apply style polish checkpatch suggested.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turns out the VLV/CHV system agent doesn't understand memory
latencies, so trying to rely on the PND deadline mechanism is not
going to fly especially when DDR DVFS is enabled. Currently we try to
avoid the problems by lying to the system agent about the deadlines
and setting the FIFO watermarks to 8 cachelines. This however leads to
bad memory self refresh residency.
So in order to satosfy everyone we'll just give up on the deadline
scheme and program the watermarks old school based on the worst case
memory latency.
I've modelled this a bit on the ILK+ approach where we compute multiple
sets of watermarks for each pipe (PM2,PM5,DDR DVFS) and when merge thet
appropriate one later with the watermarks from other pipes. There isn't
too much to merge actually since each pipe has a totally independent
FIFO (well apart from the mess with the partially shared DSPARB
registers), but still decopuling the pipes from each other seems like a
good idea.
Eventually we'll want to perform the watermark update in two phases
around the plane update to avoid underruns due to the single buffered
watermark registers. But that's still in limbo for ILK+ too, so I've not
gone that far yet for VLV/CHV either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Read out the current watermark settings from the hardware at driver init
time. This will allow us to compare the newly calculated values against
the currrent ones and potentially avoid needless WM updates.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the new DRRS code it kinda sticks out, and we never managed to
get this to work well enough without causing issues. Time to wave
goodbye.
I've decided to keep the logic for programming the reduced clocks
intact, but everything else is gone. If anyone ever wants to resurrect
this we need to redo it all anyway on top of the frontbuffer tracking.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As there is no OLR to check, the check_olr() function is now a no-op and can be
removed.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In _i915_add_request(), the request is associated with a userland client.
Specifically it is linked to the 'file' structure and the current user process
is recorded. One problem here is that the current user process is not
necessarily the same as when the request was submitted to the driver. This is
especially true when the GPU scheduler arrives and decouples driver submission
from hardware submission. Note also that it is only in the case where the add
request comes from an execbuff call that there is a client to associate. Any
other add request call is kernel only so does not need to do it.
This patch moves the client association into a separate function. This is then
called from the execbuffer code path itself at a sensible time. It also removes
the now redundant 'file' pointer from the add request parameter list.
An extra cleanup of the client association is also added to the request clean up
code for the eventuality where the request is killed after association but
before being submitted (e.g. due to out of memory error somewhere). Once the
submission has happened, the request is on the request list and the regular
request list removal will clear the association. Note that this still needs to
happen at this point in time because the request might be kept floating around
much longer (due to someone holding a reference count) and the client should not
be worrying about this request after it has been retired.
For: VIZ-5115
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä