In case of error, the function pcim_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 7740d04d90 ("usb: dwc3: pci: Enable ULPI Refclk on platforms where the firmware does not")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On Intel Edison board the OTG function is enabled, thus,
USB can switch to the host mode.
Allow that by changing dr_mode property to "otg" for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For now all PCI enumerated dwc3 devices require some properties
to be present. This allows us to unconditionally append them and supply
via driver_data.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Describe 'wakeup_work' field of struct dwc3_pci to avoid a warning:
drivers/usb/dwc3/dwc3-pci.c:59: warning: Function parameter or member 'wakeup_work' not described in 'dwc3_pci'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even though we only use them once, it is better to not put/release
the GPIOs immediately after use, so that others cannot claim them.
Use devm functions to get the phy GPIOs, so that they will be
automatically released when were unbound from the device and
remove the gpio_put calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On some Bay Trail (BYT) systems the firmware does not enable the
ULPI Refclk.
This commit adds a helper which checks and if necessary enabled the Refclk
and calls this helper for BYT machines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Bay Trail / BYT SoCs do not have a builtin device-mode phy, instead
they require an external ULPI phy for device-mode.
Only some BYT devices have an external phy, but even on those devices
device-mode is not working because the dwc3 does not see the phy.
The problem is that the ACPI fwnode for the dwc3 does not contain the
expected GPIO resources for the GPIOs connected to the chip-select and
reset pins of the phy.
I've found the workaround which some Android x86 kernels use for this:
https://github.com/BORETS24/Kernel-for-Asus-Zenfone-2/blob/master/arch/x86/platform/intel-mid/device_libs/pci/platform_usb_otg.c
Which boils down to hardcoding the GPIOs for these devices.
The good news it that all boards (*) use the same GPIOs.
This commit fixes the ULPI phy not woring by adding a gpiod_lookup_table
call which adds a hardcoded mapping for BYT devices. Note that the mapping
added by gpiod_add_lookup_table is a fallback mapping, so boards which
properly provide GPIO resources in the ACPI firmware-node resources
will not use this.
*) Except for the first revision of the evalulation-kit, which normal users
don't have
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This driver is to be used for Synopsys PCIe-base HAPS platform. Move the
the HAPS support from dwc3-pci to this driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Platform device is allocated before adding resources. Make sure to
properly cleanup on error case.
Cc: <stable@vger.kernel.org>
Fixes: f1c7e71081 ("usb: dwc3: convert to pcim_enable_device()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver currently resumes and increments pm usage_count
of its child device (dwc3 main) from its runtime_resume
handler. This requires dwc3 runtime_resume to perform
pm_runtime_put to decrement the pm usage_count. However
runtime_put from dwc3 happens for non pci drivers
(e.g. dwc3-if-simple.c) as well which results in dwc3
pm usage_count becoming negative after couple of
runtime suspend resume iterations. Fix this by
performing runtime_get/put from dwc3-pci driver only
using workqueue.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev_pm_ops is not supposed to change at runtime. Marking it
constant.
Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial. The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.
For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Intel Cannonlake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new IDs to the supported devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assignment if ->probe() fails.
While here, add a debug message in case assignment fails to allow user
see the cause of a potential issue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Gemini Lake SoC has the same DWC3 than Broxton. Add
the new ID to the supported Devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Calling platform_device_add_properties() replaces existing properties so
the "linux,sysdev_is_parent" property doesn't get set. Add this property
to each platform.
Fixes: d64ff406e5 ("usb: dwc3: use bus->sysdev for DMA configuration")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_get_dr_mode() expects the device-property to be spelled
"dr_mode" not "dr-mode".
Spelling it properly fixes the following warning showing up in dmesg:
[ 8704.500545] dwc3 dwc3.2.auto: Configuration mismatch. dr_mode forced to gadget
Signed-off-by: Hans de Goede <hdegoede@redhat.com
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dma ops for dwc3 devices are not set properly. So, use a
physical device sysdev, which will be inherited from parent,
to set the hardware / firmware parameters like dma.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_pci_dsm() is only needed if (PM || PM_SLEEP),
we should make sure it's not defined if neither of
those is defined.
This fixes a randconfig build warning.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel's BXT devices need to execute a _DSM method
during {runtime_,}{suspend,resume} in order to get a
chunk of dwc3 to power gate and save some extra
power.
Let's do that now.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We'll be tracking a little more information for PCI
drivers, it's about time we add a private structure
for that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When building a kernel with CONFIG_PM_SLEEP=n, we
get the following warning:
drivers/usb/dwc3/dwc3-pci.c:253:12: warning: 'dwc3_pci_pm_dummy' defined but not used
In order to fix this, we should only define
dwc3_pci_pm_dummy() when CONFIG_PM_SLEEP is defined.
Fixes: f6c274e11e ("usb: dwc3: pci: runtime_resume child device")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
During runtime_resume of dwc3-pci.c, we need to
runtime suspend our child device (which is dwc3
proper) otherwise nothing will happen.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel Kabylake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new ID to the supported devices.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's know that Intel's SoCs' dwc3 integration is
peripheral-only since Intel implements its own
portmux for role-swapping. In order to prevent dwc3
from ever registering and XHCI platform_device,
let's just set dr-mode to peripheral-only on Intel
SoCs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This should allow the core driver to drop handling of
platform data and expect the platform specific details to
always come from properties.
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Huang Rui <ray.huang@amd.com>
CC: John Youn <John.Youn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow for dwc3-pci to reach D3 and enable pm_runtime
by providing dummy PM hooks. Without them, PCI
subsystem won't put device to D3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
BXT-M is a Intel Broxton SoC based platform with unique PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Certain Synopsys prototyping PHY boards are not able to meet timings
constraints for LPM. This allows the PHY to meet those timings by
leaving the PHY clock running during suspend.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add platform data and set usb3_lpm_capable and has_lpm_erratum.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the alignment of the PCI device definitions. Also change the hex
digit capitalization of one constant to make it consistent with the
rest of the file and driver.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds the PCI product ID for the Synopsys USB 3.1 IP core
(DWC_usb31) on a HAPS-based PCI development platform.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe
HAPS platform. This core has the debug registers mapped at a separate
BAR in order to support enhanced hibernation.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sharing the ACPI companion with dwc3 core so it has access
to the properties defined for DWC3 in ACPI tables.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Use this additional parameter and the _optional variant to simplify the
driver and improve error handling. Also expand the comment to explain
why it's not sensible to switch to devm_gpiod_get and why the gpiod_put
is also necessary.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On some BYT platforms the USB2 PHY needs to be put into
operational mode by the controller driver with GPIOs
controlling the PHYs reset and cs signals.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removed FIXME from usb/dwc3/dwc3-pci.c by moving definition of
PCI_VENDOR_ID_SYNOPSYS shared with usb/dwc2 to linux/pci_ids.h.
Signed-off-by: Joseph Kogut <joseph.kogut@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Removing a few items that are not needed anymore and
adding separate function for quirks.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is nothing specific being done in the suspend and
resume callbacks that is not already taken care of in PCI
driver core, so dropping the functions.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
None of the PCI platforms need the NOP transceivers, and
since we can now live without the PHYs, removing
registration of the platform devices for them.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for AMD Nolan (NL) FPGA and SoC platform.
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Wei Yongjun