This will be needed by all NFC driver implementing the SE ops.
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Result is added as an NFC_ATTR_FIRMWARE_DOWNLOAD_STATUS attribute
containing the standard errno positive value of the completion result.
This event will be sent when the firmare download operation is done and
will contain the operation result.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This API must be called by NFC drivers, and its prototype was
incorrectly placed.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Loading a firmware into a target is typically called firmware
download, not firmware upload. So we rename the netlink API to
NFC_CMD_FW_DOWNLOAD in order to avoid any terminology confusion from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This API will allow NFC drivers to add and remove the secure elements
they know about or detect. Typically this should be called (asynchronously
or not) from the driver or the host interface stack detect_se hook.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Secure elements need to be discovered after enabling the NFC controller.
This is typically done by the NCI core and the HCI drivers (HCI does not
specify how to discover SEs, it is left to the specific drivers).
Also, the SE enable/disable API explicitely takes a SE index as its
argument.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Supported secure elements are typically found during a discovery process
initiated when the NFC controller is up and running. For a given NFC
chipset there can be many configurations (embedded SE or not, with or
without a SIM card wired to the NFC controller SWP interface, etc...) and
thus driver code will never know before hand which SEs are available.
So we remove this field, it will be replaced by a real SE discovery
mechanism.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When using NFC-F we should copy the NFCID2 buffer that we got from
SENSF_RES through the ATR_REQ NFCID3 buffer. Not doing so violates
NFC Forum digital requirement #189.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
Transaction starts by emitting "Direct read" and acknowledged mode
bytes. Then packet length is read allowing to allocate correct NCI
socket buffer. After that payload is retrieved.
A delay after the transaction can be added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
If acknowledged mode is set:
- CRC of header and payload is checked
- if frame reception fails (CRC error): NACK is sent
- if received frame has ACK or NACK flag: unblock nci_spi_send()
Payload is passed to NCI module.
At the end, driver interruption is re asserted.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before any operation, driver interruption is de-asserted to prevent
race condition between TX and RX.
The NCI over SPI header is added in front of NCI packet.
If acknowledged mode is set, CRC-16-CCITT is added to the packet.
Then the packet is forwarded to SPI module to be sent.
A delay after the transaction is added.
This delay is determined by the driver during nci_spi_allocate_device()
call and can be 0.
After data has been sent, driver interruption is re-asserted.
If acknowledged mode is set, nci_spi_send will block until
acknowledgment is received.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFC Forum defines a transport interface based on
Serial Peripheral Interface (SPI) for the NFC Controller
Interface (NCI).
This module implements the SPI transport of NCI, calling SPI module
directly to read/write data to NFC controller (NFCC).
NFCC driver should provide functions performing device open and close.
It should also provide functions asserting/de-asserting interruption
to prevent TX/RX race conditions.
NFCC driver can also fix a delay between transactions if needed by
the hardware.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is a simple forward to the HCI driver. When driver is done with the
operation, it shall directly notify NFC Core by calling
nfc_fw_upload_done().
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As several NFC chipsets can have their firmwares upgraded and
reflashed, this patchset adds a new netlink command to trigger
that the driver loads or flashes a new firmware. This will allows
userspace triggered firmware upgrade through netlink.
The firmware name or hint is passed as a parameter, and the driver
will eventually fetch the firmware binary through the request_firmware
API.
The cmd can only be executed when the nfc dev is not in use. Actual
firmware loading/flashing is an asynchronous operation. Result of the
operation shall send a new event up to user space through the nfc dev
multicast socket. During operation, the nfc dev is not openable and
thus not usable.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
skb->dev is used for carrying a net_device pointer and not
an nci_dev pointer.
Remove usage of skb-dev to carry nci_dev and replace it by parameter
in nci_recv_frame(), nci_send_frame() and driver send() functions.
NfcWilink driver is also updated to use those functions.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All NFC devices will now get proper RFKILL support as long as they provide
some dev_up and dev_down hooks. Rfkilling an NFC device will bring it down
while it is left to userspace to bring it back up when being rfkill unblocked.
This is very similar to what Bluetooth does.
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Each NFC adapter can have several links to different secure elements and
that property needs to be exported by the drivers.
A secure element link can be enabled and disabled, and card emulation will
be handled by the currently active one. Otherwise card emulation will be
host implemented.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some chips diverge from the HCI spec in their implementation of standard
features. This adds a new quirks parameter to
nfc_hci_allocate_device() to let the driver indicate its divergence.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an adapter is removed, it will unregister itself from hci and/or
nfc core. In order to do that safely, work tasks must first be canceled
and prevented to be scheduled again, before the hci or nfc device can be
destroyed.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As a consequence the NFC device IDs won't be increasing all the time,
as IDR provides the first available ID.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver now has all HCI stuff isolated in one file, and all the
hardware link specifics in another. Writing a pn544 driver on top of
another hardware link is now just a matter of adding a new file for that
new hardware specifics.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Set the local general bytes and default value for NFCIP1
Target/Initiator registries if the protocol is NFC-DEP
Signed-off-by: Arron Wang <arron.wang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
xmit callback provided by a driver encapsulates upper layers
data and sends it to the hardware. So, HCI does not know the
exact amount of data being sent and thus can't handle partially
sent frames properly.
Therefore, the driver must return 0 for completely sent frame or
negative for failure.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Acked-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The previous shdlc HCI driver and its header are removed from the tree.
PN544 now registers directly with HCI and passes the name of the llc it
requires (shdlc).
HCI instantiation now allocates the required llc instance. The llc is
started when the HCI device is brought up.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is used by HCI drivers such as the one for the pn544 which require
communications between HCI and the chip to use shdlc.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is a passthrough llc. It can be used by HCI drivers that don't
need link layer control. HCI will then write directly to the driver, and
driver will deliver incoming frames directly to HCI without any
processing.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The LLC layer manages modules that control the link layer protocol (such
as shdlc) between HCI and an HCI driver. The driver must simply specify
the required llc when it registers with HCI.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This enables the completion callback to be called from a different
context, preventing a possible deadlock if the callback resulted in the
invocation of a nested call to the currently locked nfc_dev.
This is also more in line with the im_transceive nfc_ops for NFC Core or
NCI drivers which already behave asynchronously.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This method initiates execution of an HCI cmd. Result will be delivered
through an asynchronous callback.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC is using a number of custom ordered workqueues w/ WQ_MEM_RECLAIM.
WQ_MEM_RECLAIM is unnecessary unless NFC is gonna be used as transport
for storage device, and all use cases match one work item to one
ordered workqueue - IOW, there's no actual ordering going on at all
and using system_nrt_wq gives the same behavior.
There's nothing to be gained by using custom workqueues. Use
system_nrt_wq instead and drop all the custom ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During NFC-DEP target activation, store the remote
general bytes to be used later in dep_link_up.
When dep_link_up is called, activate the NFC-DEP target,
and forward the remote general bytes.
When dep_link_down is called, deactivate the target.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If initiator protocol is NFC-DEP, set the local general bytes
in nci_start_poll.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some NFC chips will statically create and open pipes for both standard
and proprietary gates. The driver can now pass this information to HCI
such that HCI will not attempt to create and open them, but will instead
directly use the passed pipe ids.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This API should be used by drivers, HCI, SHDLC or NCI stacks to report an
unrecoverable error.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This routine will be called by drivers whenever they receive data in target
mode. This should be unexpected events and as such should be handled by a
standalone API (i.e. not as a callback pointer from an existing API).
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Userspace gets a netlink event upon target mode activation.
The LLCP layer is also signaled when we get an ATR_REQ in order to get
the remote general bytes.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFC core code already does that for them.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is now specified that nfc_target_found() and nfc_target_lost() core
functions must not be called from an atomic context. This allow us to
serialize calls and protect the targets table using the nfc device lock
instead of a spinlock.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC Core now caches the active nfc target pointer, thereby avoiding
the need to lookup the target table for each invocation of a driver ops.
Consequently, pn533, HCI and NCI now directly receive an nfc_target
pointer instead of a target index.
Cc: Ilan Elias <ilane@ti.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HW/drivers get notifications when a tag moves out of the radio field.
This notification is now forwarded to user space through netlink.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The target index can be used by userspace to uniquely identify a target
and thus should be kept unique, per NFC adapter. Moreover, some protocols
do not provide a logical index when discovering new targets, so we have to
generate one for them.
For NCI or pn533 to fetch their logical index, we added a logical_idx field
to the target structure.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most NFC HCI chipsets actually use a simplified HDLC link layer to
carry HCI payloads.
This implementation registers itself as an HCI device on behalf of the
NFC driver.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is an implementation of ETSI TS 102 622 specification.
Many NFC chipsets use HCI as the host <-> target protocol on top of a
serial link like i2c.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NFC drivers will call this routine when they detect that a tag leaves the
RF field. This will eventually lead to the corresponding netlink event
to be sent.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When calling nfc_dep_link_up, we implicitely are in initiator mode.
Which means we also can provide the general bytes as a function argument,
as all drivers will eventually request them.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC core layer should not set the target_idx.
Instead, the driver layer (e.g. NCI, PN533) should set the
target_idx, so that it will be able to identify the target
when its I/F (e.g. activate_target) is called.
This is required in order to support multiple targets.
Note that currently supported drivers (PN533 and NCI) don't
use the target_idx in their implementation.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make a clear separation between NCI states and flags.
This is required in order to support more NCI states (e.g.
for multiple targets support).
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add NCI data exchange timer to catch timeouts,
and call the data exchange callback with an error.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export new attributes sensb_res for tech B and sensf_res
for tech F in the target info (returned as a response to
NFC_CMD_GET_TARGET).
The max size of the attributes nfcid1, sensb_res and sensf_res
is exported to user space though include/linux/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase NCI deactivate timeout from 5 sec to 30 sec.
NCI deactivate procedure might take a long time,
depending on the local and remote parameters.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nfcid1 is the NFC-A identifier.
It is exported as an attribute of the target info
(returned as a response to NFC_CMD_GET_TARGET).
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for NCI Interface Error Notification.
When this notification is received and we're during a
data exchange transaction, indicate an error to the NFC
core layer via the data exchange callback.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition, deletion, and modification of NCI constants.
Changes in NCI commands, responses, and notifications structures.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without an API for setting and getting the local and remote general bytes,
drivers won't be able to properly establish a DEP link.
This API also allows them to propagate the remote general bytes they get
from the DEP link establishment up to the LLCP layer.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NFC-DEP (Data Exchange Protocol) is an NFC MAC layer.
This command allows to enable and disable the DEP link on to which e.g.
LLCP can run.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a factorization of the current rawsock tx skb allocation routine,
as it will be used by the LLCP code.
We also rename nfc_alloc_skb to nfc_alloc_recv_skb for consistency sake.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if NCI data flow control is used in nci_tx_work.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused NCI operations, e.g. create static rf connection.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition, deletion and modification of NCI constants.
Changes in NCI commands, responses and notifications structures.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Protect 'cb' and 'cb_context' arguments in nci_data_exchange.
In fact, this implements a queue with max length of 1 data
exchange transactions in parallel.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC Controller Interface (NCI) is a standard
communication protocol between an NFC Controller (NFCC)
and a Device Host (DH), defined by the NFC Forum.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The file nfc.h was moved from include/net to include/net/nfc,
since new NFC header files will be added to include/net/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>