Following changes are made as part of this change:
1. As TWL RTC supports periodic interrupt, the correct event should be
RTC_PF instead of RTC_UF.
2. No need to initialize variable "events" to 0 & then OR it with the
event values. Hence fixing it.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For clearing RTC interrupt, programming ALARM bit only is sufficient, as
all other bits are any way not affected by writing 0 to them.
Hence removed unwanted OR operation.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As part of probe, before enabling RTC, RTC_CTRL register is read to check
if it is already running. If RTC is used by kernel alone, then this read
is not required. Even if RTC was enabled already by boot loader, setting
STOP_RTC bit again should not harm. Hence removed unwanted read
operation.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the TWL RTC driver has a cached copy of enabled RTC interrupt bits in
variable rtc_irq_bits, that can be checked before really setting or
masking any of the interrupt bits.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Factor out some boilerplate code for spi driver registration into
module_spi_driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Dennis Aberilla <denzzzhome@yahoo.com>
Cc: Nikolaus Voss <n.voss@weinmann.de>
Cc: "Kim B. Heino" <Kim.Heino@bluegiga.com>
Cc: Raphael Assenat <raph@raphnet.net>
Cc: Chris Verges <chrisv@cyberswitching.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rtc_device_register() calls rtc-spear routines internally. These
routines call dev_get_drvdata() to get struct spear_rtc_config.
Currently, platform_set_drvdata is called after rtc device is
registered. This causes system to crash, as dev_get_drvdata returns
NULL.
For this we need to call platform_set_drvdata() before registering rtc
device. This requires further cleanup, that leads to removal of
dev_set_drvdata on rtc->dev, which was just not required at all.
Also, we change the parameter to request_irq and pass pointer to config
instead of pointer to rtc struct.
This patch brings all above changes.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define API for '.alarm_irq_enable' to enable and disable alarm irq. This
is required by the framework else RTC_AIE_ON and RTC_AIE_OFF ioctls
return errors.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle the fix for unbalanced irq for the cases when enable_irq_wake
fails, and a warning related to same is displayed on the console. The
workaround is handled at the driver level.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer changes for v3.4 from Ingo Molnar
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
ntp: Fix integer overflow when setting time
math: Introduce div64_long
cs5535-clockevt: Allow the MFGPT IRQ to be shared
cs5535-clockevt: Don't ignore MFGPT on SMP-capable kernels
x86/time: Eliminate unused irq0_irqs counter
clocksource: scx200_hrt: Fix the build
x86/tsc: Reduce the TSC sync check time for core-siblings
timer: Fix bad idle check on irq entry
nohz: Remove ts->Einidle checks before restarting the tick
nohz: Remove update_ts_time_stat from tick_nohz_start_idle
clockevents: Leave the broadcast device in shutdown mode when not needed
clocksource: Load the ACPI PM clocksource asynchronously
clocksource: scx200_hrt: Convert scx200 to use clocksource_register_hz
clocksource: Get rid of clocksource_calc_mult_shift()
clocksource: dbx500: convert to clocksource_register_hz()
clocksource: scx200_hrt: use pr_<level> instead of printk
time: Move common updates to a function
time: Reorder so the hot data is together
time: Remove most of xtime_lock usage in timekeeping.c
ntp: Add ntp_lock to replace xtime_locking
...
If probing the RTC didn't succeed due to failed RTC register access, the
RTC device will be unregistered. Then, when removing the module
r9701_remove() causes a kernel crash while trying to unregister a not
registered RTC device. Fix this by doing RTC register access test before
RTC device registration.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of computing virtual address with AT91_VA_BASE_SYS, use the
appropriate ioremap() call on the driver "memory" resource.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Currently, the RTC code does not disable the alarm in the hardware.
This means that after a sequence such as the one below (the files are in the
RTC sysfs), the box will boot up after 2 minutes even though we've
asked for the alarm to be turned off.
# echo $((`cat since_epoch`)+120) > wakealarm
# echo 0 > wakealarm
# poweroff
Fix this by disabling the alarm when there are no timers to run.
The original version of this patch was reverted. This version
disables the irq directly instead of setting a disabled timer
in the future.
Cc: stable@kernel.org
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Merged in the second revision from Rabin]
Signed-off-by: John Stultz <john.stultz@linaro.org>
If the alarm time programming in the rtc is ever in the past, it won't fire,
and any other alarm will be queued after it so they won't fire either.
So any time that the alarm might be in the past, we need to trigger
the irq handler to ensure the old alarm is cleared and the timer queue
is fully in the future.
This is done whenever the RTC clock is set.
This is the second revision of this patch, which was earlier reverted.
This version avoids the initialization problem, which is handled by
a different patch.
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: NeilBrown <neilb@suse.de>
[Remove problematic initialization change, update commit log, also
catch set_mmss case -jstultz]
Signed-off-by: John Stultz <john.stultz@linaro.org>
In some cases at boot up, the RTC alarm may be set in the past,
but still have the enabled flag on. This was causing problems,
because we would then enqueue the alarm into the timerqueue,
but it would never fire. This would clog up the timerqueue
and keep other alarms from working.
The fix is to check the alarm against the current rtc time at
boot and avoid enqueueing the alarm if it is in the past.
Reported-by: NeilBrown <neilb@suse.de>
Tested-by: NeilBrown <neilb@suse.de>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This reverts commit 42874759d7.
This wasn't tested as a stand-alone patch, and it has build errors
without the following patches applied:
drivers/rtc/rtc-sa1100.c: In function 'sa1100_rtc_set_alarm':
drivers/rtc/rtc-sa1100.c:208: error: 'now' undeclared (first use in this function)
drivers/rtc/rtc-sa1100.c:208: error: (Each undeclared identifier is reported only once
drivers/rtc/rtc-sa1100.c:208: error: for each function it appears in.)
drivers/rtc/rtc-sa1100.c:210: error: incompatible type for argument 3 of 'rtc_next_alarm_time'
drivers/rtc/rtc-sa1100.c:211: error: 'time' undeclared (first use in this function)
So it too gets reverted to bring us back to a working point.
This reverts commit 7cea00657d.
The sa1100 cleanups fatally broke the SA1100 RTC driver - the first
hint that something is wrong are these compiler warnings:
drivers/rtc/rtc-sa1100.c:42:1: warning: "RCNR" redefined
In file included from arch/arm/mach-sa1100/include/mach/hardware.h:73,
from drivers/rtc/rtc-sa1100.c:35:
arch/arm/mach-sa1100/include/mach/SA-1100.h:877:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:43:1: warning: "RTAR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:876:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:44:1: warning: "RTSR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:879:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:45:1: warning: "RTTR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:878:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:47:1: warning: "RTSR_HZE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:891:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:48:1: warning: "RTSR_ALE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:890:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:49:1: warning: "RTSR_HZ" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:889:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:50:1: warning: "RTSR_AL" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:888:1: warning: this is the location of the previous definition
and the second problem, which is far more severe, are the different
register layouts, resulting in the wrong registers being read on
SA11x0 platforms. This patch adds:
#define RCNR 0x00 /* RTC Count Register */
#define RTAR 0x04 /* RTC Alarm Register */
#define RTSR 0x08 /* RTC Status Register */
#define RTTR 0x0c /* RTC Timer Trim Register */
but the SA11x0 registers are:
#define RTAR __REG(0x90010000) /* RTC Alarm Reg. */
#define RCNR __REG(0x90010004) /* RTC CouNt Reg. */
#define RTTR __REG(0x90010008) /* RTC Trim Reg. */
#define RTSR __REG(0x90010010) /* RTC Status Reg. */
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel config: Fix the APB_TIMER selection
x86/mrst: Add additional debug prints for pb_keys
x86/intel config: Revamp configuration to allow for Moorestown and Medfield
x86/intel/scu/ipc: Match the changes in the x86 configuration
x86/apb: Fix configuration constraints
x86: Fix INTEL_MID silly
x86/Kconfig: Cyclone-timer depends on x86-summit
x86: Reduce clock calibration time during slave cpu startup
x86/config: Revamp configuration for MID devices
x86/sfi: Kill the IRQ as id hack
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") introduced a
potential infinite loop. If an alarm time contains a wildcard month and
an invalid day (> 31), or a wildcard year and an invalid month (>= 12),
the loop searching for the next matching date will never terminate. Treat
the invalid values as wildcards.
Fixes <http://bugs.debian.org/646429>, <http://bugs.debian.org/653331>
Reported-by: leo weppelman <leoweppelman@googlemail.com>
Reported-by: "P. van Gaans" <mailme667@yahoo.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the DT support for the TI rtc-twl present in the twl4030 and twl6030
devices.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ancient times it was necessary to manually initialize the bus field of
an spi_driver to spi_bus_type. These days this is done in
spi_driver_register(), so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts the drivers in drivers/rtc/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marginally less code and eliminate the possibility of memory leaks.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to changes in the RTC core the period interrupt is now unused so
delete the code managing it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc_calibration attribute allows user-space to get and set the
AB8500's RtcCalibration register. The AB8500 will then use the value in
this register to compensate for RTC drift every 60 seconds.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mark Godfrey <mark.godfrey@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The resolution of msleep is related to HZ, so with HZ set to 100 any
msleep of less than 10ms will become ~10ms. This is not what we want.
Use the hrtimer-based usleep_range() and allow for some slack in the
non-critical path so we have more control of what is happening here.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Jonas Aaberg <jonas.aberg@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set can_wake flag so wakealarm property is visible in sysfs.
Signed-off-by: Andrew Lynn <andrew.lynn@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We want this driver to be able to wake up the system.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix alarm IRQ handling, make the alarm one-shot. Cleanup black magick
with a validation of already validated time data.
Add ability to wake the system with alarm.
[akpm@linux-foundation.org: fix CONFIG_PM=n build]
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no way to track year in the i.MX1 RTC: Days Counter register is
9-bit wide only. Attempt to save date after 1970-01-01 plus 512 days
causes endless loop in mxc_rtc_set_mmss(). Fix this by resetting year to
1970.
[akpm@linux-foundation.org: use conventional comment layout]
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix writing to NVRAM bank 2 in rtc-cmos driver. It never worked since its
introduction in 2.6.28 because of a typo.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch renames puv3_rtcdrv to puv3_rtc_driver, so that modpost will know
that this is simply a list of pointers to driver functions, in which case
the section mismatch is OK. (Thanks Michal Marek)
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
--
Section mismatch warning information:
WARNING: drivers/rtc/built-in.o(.data+0x90): Section mismatch in
reference from the variable puv3_rtcdrv to the
function .devinit.text:puv3_rtc_probe()
The variable puv3_rtcdrv references
the function __devinit puv3_rtc_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: drivers/rtc/built-in.o(.data+0x94): Section mismatch in
reference from the variable puv3_rtcdrv to the
function .devexit.text:puv3_rtc_remove()
The variable puv3_rtcdrv references
the function __devexit puv3_rtc_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: drivers/built-in.o(.data+0x6c04): Section mismatch in reference
from the variable puv3_rtcdrv to the
function .devinit.text:puv3_rtc_probe()
The variable puv3_rtcdrv references
the function __devinit puv3_rtc_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: drivers/built-in.o(.data+0x6c08): Section mismatch in reference
from the variable puv3_rtcdrv to the
function .devexit.text:puv3_rtc_remove()
The variable puv3_rtcdrv references
the function __devexit puv3_rtc_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: vmlinux.o(.data+0x1126c): Section mismatch in reference from
the variable puv3_rtcdrv to the function .devinit.text:puv3_rtc_probe()
The variable puv3_rtcdrv references
the function __devinit puv3_rtc_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
WARNING: vmlinux.o(.data+0x11270): Section mismatch in reference from
the variable puv3_rtcdrv to the function .devexit.text:puv3_rtc_remove()
The variable puv3_rtcdrv references
the function __devexit puv3_rtc_remove()
If the reference is valid then annotate the
variable with __exit* (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
This patch converts the driver to use the module_platform_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
This is where the really nasty conflicts in the samsung platform
start, due to some files getting moved around and combined in the
'restart' branch that has already gone into mainline through
Russell's tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XY2N
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
I ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9q+1
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Cleanups on various subarchitectures
Cleanup patches for various ARM platforms and some of their associated
drivers, the bulk of these is for mach-91.
Arnd ended up pulling in the restart branch from Russell in order to
fix up some simple but annoying merge conflicts.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
arm/at91: fix build of stamp9g20
ARM: u300: delete memory.h
MAINTAINERS: add maintainer entry for Picochip picoxcell
ARM: picoxcell: move io mappings to common.c
ARM: picoxcell: don't reserve irq_descs
ARM: picoxcell: remove mach/memory.h
ARM: at91: delete the pcontrol_g20_defconfig
arm/tegra: Remove code that's ifndef CONFIG_ARM_GIC
arm/tegra: remove unused defines
arm/tegra: fix variable formatting in makefile
ARM: davinci: vpif: move code to driver core header from platform
ARM: at91/gpio: fix display of number of irq setuped
ARM: at91/gpio: drop PIN_BASE
ARM: at91/udc: use gpio_is_valid to check the gpio
ARM: at91/ohci: use gpio_is_valid to check the gpio
ARM: at91/nand: use gpio_is_valid to check the gpio
ARM: at91/mmc: use gpio_is_valid to check the gpio
ARM: at91/ide: use gpio_is_valid to check the gpio
ARM: at91/pata: use gpio_is_valid to check the gpio
ARM: at91/soc: use gpio_is_valid to check the gpio
...
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Conflicts:
arch/arm/mach-exynos/common.c
The common.c file gets changes from rmk/stable-devel (part of
next/cleanup), rmk/restart, samsung/dt and follow-on branches
from the samsung tree.
Pulling it all together here hopefully avoids having to do
even more conflicting merge changesets in this one file. What
a mess!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-exynos/Makefile
arch/arm/mach-exynos/cpu.c -> common.c
arch/arm/mach-exynos/include/mach/entry-macro.S
arch/arm/mach-exynos/init.c -> common.c
arch/arm/mach-s5p64x0/init.c -> common.c
arch/arm/mach-s5pv210/init.c -> common.c
Multiple files were moved into common.c files in the rmk/for-linus
branch, so this moves over the samsung/dt changes to the new
files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-exynos/cpu.c
arch/arm/mach-shmobile/board-kota2.c
This resolves a bunch of conflicts between the arm-soc tree
and changes from the arm tree that have gone upstream.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
Venu Byravarasu