If a gadget driver loaded to a Superspeed-capable
peripheral controller, using a Superspeed cable,
doesn't provide Superspeed descriptors, we will get
a NULL pointer dereference.
In order to avoid that situation, we will try to
find any valid descriptors we can. If no set of
descriptors is passed in, then we'll let that gadget
oops anyhow.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For convenience, passing the dwc3 platform device as a
parameter to dwc3_pci_quirks() function.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Setting the ACPI companion before calling dwc3_pci_quirks.
The ACPI companion will be set unconditionally as the
primary fwnode, overriding any previously set primary
fwnode. This will make sure that any build-in properties
added to the platform device will be added as the secondary
fwnode in cases where also ACPI companion exists.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case host sends us an unsupported test mode, we
*must* stall this request. This will tell the host
that the selector is invalid and we won't put the
controller in unsupported test modes which could
have undetermined side-effects.
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
whc_init already calls whc_clean_up if an error occurs during
the initialization, so calling it again if whc_init fails at
the end of wch_probe will cause double free errors. Fix this
by bailing out on an whc_init failure to a new label that avoids
doing the duplicated whc_clean_up.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thanks to switching to devm_gpiod_get:
1) We don't have to pass fwnode pointer
2) We can request initial GPIO value at getting call
This was successfully tested on Netgear R6250 (BCM4708).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that there are no more users for
xhci_plat_type_is(), we can safely remove it.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the code has been refactored enough,
switching over to using ->plat_start() and
->init_quirk() becomes a very simple patch.
After this patch, there are no further uses for
xhci_plat_type_is() which will be removed in a
follow-up patch.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like RCAR's init_quirk() we want mvebu's to use
struct usb_hcd * as argument too. This is another
step towards removing xhci_plat_type_is().
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_plat_setup() is the rightful place for
xhci_mvebu_mbus_init_quirk(), so let's move it there
in order to make it simpler to get rid of
xhci_plat_type_is() later on.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
these two methods will be used to hide
platform-specific details so we can get rid of
xhci_plat_type_is() in a later patch.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're preparing to remove xhci_plat_type_is() in
favor of a better approach where we define function
pointers ahead of time. This will let us make
assumptions about which platforms we're running on
and which platform-specific functions we should call.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[delete extra comma in function parameters -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move duplicate code from xhci_queue_intr_tx()
and xhci_queue_isoc_tx_prepare() to the check_interval() function.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove duplicate function xhci_urb_to_transfer_ring from xhci.c.
We have same function in xhci-ring.c.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In drivers/usb/host/xhci-ring.c there are two functions
(xhci_queue_bulk_tx and queue_bulk_sg_tx) that are very similar,
so a lot of code duplication.
This patch merges these functions into to one xhci_queue_bulk_tx.
Also counting the needed TRBs is merged and refactored.
Signed-off-by: Alexandr Ivanov <alexandr.sky@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restructure usb_sg_cancel() so we don't have to disable interrupts
while cancelling the URBs.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_submit_urb() may take quite long to execute. For example, a
single sg list may have 30 or more entries, possibly leading to that
many calls to DMA-map pages. This can cause interrupt latency of
several hundred micro-seconds.
Avoid the problem by releasing the io->lock spinlock and re-enabling
interrupts before calling usb_submit_urb(). This opens races with
usb_sg_cancel() and sg_complete(). Handle those races by using
usb_block_urb() to stop URBs from being submitted after
usb_sg_cancel() or sg_complete() with error.
Note that usb_unlink_urb() is guaranteed to return -ENODEV if
!io->urbs[i]->dev and since the -ENODEV case is already handled,
we don't have to check for !io->urbs[i]->dev explicitly.
Before this change, reading 512MB from an ext3 filesystem on a USB
memory stick showed a throughput of 12 MB/s with about 500 missed
deadlines.
With this change, reading the same file gave the same throughput but
only one or two missed deadlines.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the driver to Kconfig to make it visible in menuconfig
and allow people to compile it.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sysfs attributes to allow controlling vudc from usbip tools.
dev_desc - device descriptor of current gadget. This is required to
be consisten with current usbip protocol and allow to list
exportable devices on given machine.
usbip_sockfd - allows to pass socket to kernel to start usbip transfer.
usbip_status - currnent status of device
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes, improvements and commit msg update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add endpoints definitions and ops for both endpoints and gadget.
Add also a suitable platform driver and functions for handling
usbip events.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes, improvements and commit msg update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file contains functions for returning requests to the client.
It also has functions that add requests completed in vudc_rx and
vudc_transfer to the return queue.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file contains a function that simulates USB traffic, based on
the one in dummy_hcd. Is also handles udc-directed control
requests, and contains functions for setting up and controlling
a timer for the emulation.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add functions which allows to receive urbs from the client.
It receives traffic in a loop in a separate thread.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add main vudc module file. This allows us to register suitable
platform device and driver (just like dummy_hcd does).
Currently number of vudc instances is determined using module
parameter but whole infrastructure is suitable to make vudc
creation dynamic (for example via configfs).
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Various bug fixes and commit message update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add constants for VUDC events in usbip_common.h
and make use of them in usbip_common.c.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Small fixes and commit message update]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add header with definitions needed by vudc driver.
This commit is a result of cooperation between Samsung R&D Institute
Poland and Open Operating Systems Student Society at University
of Warsaw (O2S3@UW) consisting of:
Igor Kotrasinski <ikotrasinsk@gmail.com>
Karol Kosik <karo9@interia.eu>
Ewelina Kosmider <3w3lfin@gmail.com>
Dawid Lazarczyk <lazarczyk.dawid@gmail.com>
Piotr Szulc <ps347277@students.mimuw.edu.pl>
Tutor and project owner:
Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Karol Kosik <karo9@interia.eu>
[Some small improvements]
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional changes here, just making sure our
storage driver uses a consistent multi-line comment
style.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 devices, because they are much newer, have much
less chance of having issues with larger transfers.
We still keep a limit because anything above 2048
sectors really rendered negligible speed
improvements, so we will simply ignore
that. Transferring 1MiB should already give us
pretty good performance.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just so we have some sort of documentation as to why
we limit our Mass Storage transfers to 240 sectors,
let's update the comment to make clearer that
devices were found that would choke with larger
transfers.
While at that, also make sure to clarify that other
operating systems have similar, albeit different,
limits on mass storage transfers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a port can do 10 Gb/s the kernel should say so.
The corresponding check needs to be added.
Signed-off.by: Oliver Neukum <ONeukum@suse.com>>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_get_phy() function returns either a valid pointer to phy or
ERR_PTR() error, check for NULL always fails and may lead to oops on
error path, fix this issue.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2035772010.
Commit 20357720 claims throughput improvement for MSC/UVC, but I
don't see much improvement. Following are the MSC measurement using
dd on AM335x GP EVM.
with BCD_BH: read: 14.9MB/s, write: 20.9MB/s
without BCD_BH: read: 15.2MB/s, write: 21.2MB/s
However with this commit the following regressions have been observed.
1. ASIX usb-ethernet dongle is completely broken on UDP RX.
2. Unpluging a 3G modem, which uses option driver, behind a hub causes
console log flooding with the following message.
option_instat_callback: error -71
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some functions, such as f_sourcesink, rely on an endpoint's desc
field during their requests' complete() callback, so clear it only
_after_ nuking all requests to avoid NULL pointer dereference.
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The ftdi_sio_quirk structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Johan Hovold <johan@kernel.org>
Adding VID:PID for Straizona Focusers to cp210x driver.
Signed-off-by: Jasem Mutlaq <mutlaqja@ikarustech.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Link ECU is an aftermarket ECU computer for vehicles that provides
full tuning abilities as well as datalogging and displaying capabilities
via the USB to Serial adapter built into the device.
Signed-off-by: Mike Manning <michael@bsch.com.au>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When using asynchronous read or write operations on the USB endpoints the
issuer of the IO request is notified by calling the ki_complete() callback
of the submitted kiocb when the URB has been completed.
Calling this ki_complete() callback will free kiocb. Make sure that the
structure is no longer accessed beyond that point, otherwise undefined
behaviour might occur.
Fixes: 2e4c7553cd ("usb: gadget: f_fs: add aio support")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a bunch of information in the debug register
set from dwc3 which is useful in some debugging
scenarios. Let's dump them out in endpoint-specific
directories and designated files.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This helper will be used later to convert trb type
into a human-readable string for debugfs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
this helper will be used, initially, to dump space
of different queues and fifos in dwc3 to
debugfs. Later, it'll be used to issue remote wakeup
when we want to start a transfer and there's
something in a TX FIFO.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Coccinelle caught this instance of us kfree()ing
devm-allocated memory. The solution is just to not
do anything in our gadget_release.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When binding the function to usb_configuration, check whether the thread
is running before starting another one. Without that, when function
instance is added to multiple configurations, fsg_bing starts multiple
threads with all but the latest one being forgotten by the driver. This
leads to obvious thread leaks, possible lockups when trying to halt the
machine and possible more issues.
This fixes issues with legacy/multi¹ gadget as well as configfs gadgets
when mass_storage function is added to multiple configurations.
This change also simplifies API since the legacy gadgets no longer need
to worry about starting the thread by themselves (which was where bug
in legacy/multi was in the first place).
N.B., this patch doesn’t address adding single mass_storage function
instance to a single configuration twice. Thankfully, there’s no
legitimate reason for such setup plus, if I’m not mistaken, configfs
gadget doesn’t even allow it to be expressed.
¹ I have no example failure though. Conclusion that legacy/multi has
a bug is based purely on me reading the code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the current implementation functionfs generates a EFAULT for async read
operations if the read buffer size is larger than the URB data size. Since
a application does not necessarily know how much data the host side is
going to send it typically supplies a buffer larger than the actual data,
which will then result in a EFAULT error.
This behaviour was introduced while refactoring the code to use iov_iter
interface in commit c993c39b86 ("gadget/function/f_fs.c: use put iov_iter
into io_data"). The original code took the minimum over the URB size and
the user buffer size and then attempted to copy that many bytes using
copy_to_user(). If copy_to_user() could not copy all data a EFAULT error
was generated. Restore the original behaviour by only generating a EFAULT
error when the number of bytes copied is not the size of the URB and the
target buffer has not been fully filled.
Commit 342f39a6c8 ("usb: gadget: f_fs: fix check in read operation")
already fixed the same problem for the synchronous read path.
Fixes: c993c39b86 ("gadget/function/f_fs.c: use put iov_iter into io_data")
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This function compiles to 298 bytes of machine code, has ~10 callsites.
This is a USB 2.0 device, USB 2.0 is limited to ~40 MB/s, so should be
almost never CPU bound. No need to optimize for speed this agressively.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Felipe Balbi <balbi@ti.com>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The previous code could use the first USB-DMAC with IPMMU if iommus
property was set into this device node. However, in this case, it
could not control the second USB-DMAC with IPMMU because a parameter
of IPMMU (micro-TLB id) is different with each USB-DMAC.
So, this patch uses the usb_gadget_{un}map_request_by_dev() APIs for
IPMMU. (Then, iommus property should be set into USB-DMAC node(s).)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since usbhsg_dma_map_ctrl() needs DMA device structure in the near future,
this patch changes arguments of dma_map_ctrl() to give such data.
(This patch is only change the argument.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since usbhsf_dma_{un}map() will use the "fifo" data in the near future,
this patch changes function call orfer in usbhsf_dma_prepare_push().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the following environment, the first argument of DMA API should
be set to a DMAC's device structure, not a udc controller's one.
- A udc controller needs an external DMAC device (like a DMA Engine).
- The external DMAC enables IOMMU.
So, this patch add usb_gadget_{un}map_request_by_dev() API to set
a DMAC's device structure by a udc controller driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The argument of dev_err() in usb_gadget_map_request() should be dev
instead of &gadget->dev.
Fixes: 7ace8fc ("usb: gadget: udc: core: Fix argument of dma_map_single for IOMMU")
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Debugfs init failure is not so important. We can continue our job on
this failure. Also no break need for debugfs_create_file call failure.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[felipe.balbi@linux.intel.com :
- remove out-of-memory message, we get that from OOM.
- switch dev_err() to dev_dbg() ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dma_status bit flag is set but never really used
so get rid of it.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It makes no sense to interrupt in the middle of
chained transfer. This patch just makes sure we
don't do that.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of limiting link TRB only to Isoc endpoints,
let's use it for all endpoint types, this way we are
more likely to transfer more data before a
XferComplete event.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By moving our % DWC3_NUM_TRB operation to the
increment helpers, the rest of the driver can be
simplified.
It's also a good practice to make sure we will have
a single place dealing with details about how to
increment our enqueue and dequeue pointers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add three little helpers which will aid in making
the code slightly easier to read. One helper
increments enqueue pointer, another increments
dequeue pointer and the last one tests if we're
dealing with the last TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of using a bitwise and, let's rely on the %
operator since that's a lot more clear. Also, GCC
will optimize % 256 to nothing anyway.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The call to wusb_dev_sysfs_rm() which is just after return will never
be executed. On checking the code, wusb_dev_sysfs_add() is the last one
to be executed so even if that fails we do not need wusb_dev_sysfs_rm()
in the error path.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dear all,
1. Overview
In current USB/IP implementation, event kernel threads are created for
each port. The functions of the threads are closing connection and
error handling so they don't have not so many events to handle. There's
no need to have thread for each port.
BEFORE) vhci side - VHCI_NPORTS(8) threads are created.
$ ps aux | grep usbip
root 10059 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10060 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10061 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10062 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10063 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10064 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10065 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
root 10066 0.0 0.0 0 0 ? S 17:06 0:00 [usbip_eh]
BEFORE) stub side - threads will be created every bind operation.
$ ps aux | grep usbip
root 8368 0.0 0.0 0 0 ? S 17:56 0:00 [usbip_eh]
root 8399 0.0 0.0 0 0 ? S 17:56 0:00 [usbip_eh]
This patch put event threads of stub and vhci driver as one workqueue.
AFTER) only one event threads in each vhci and stub side.
$ ps aux | grep usbip
root 10457 0.0 0.0 0 0 ? S< 17:47 0:00 [usbip_event]
2. Modification to usbip_event.c
BEFORE) kernel threads are created in usbip_start_eh().
AFTER) one workqueue is created in new usbip_init_eh().
Event handler which was main loop of kernel thread is modified to
workqueue handler.
Events themselves are stored in struct usbip_device - same as before.
usbip_devices which have event are listed in event_list.
The handler picks an element from the list and wakeup usbip_device. The
wakeup method is same as before.
usbip_in_eh() substitutes statement which checks whether functions are
called from eh_ops or not. In this function, the worker context is used
for the checking. The context will be set in a variable in the
beginning of first event handling. usbip_in_eh() is used in event
handler so it works well.
3. Modifications to programs using usbip_event.c
Initialization and termination of workqueue are added to init and exit
routine of usbip_core respectively.
A. version info
v2)
# Merged 1/2 event handler itself and 2/2 user programs because of auto
build fail at 1/2 casued unmodified user programs in 1/2.
Signed-off-by: Nobuo Iwata <nobuo.iwata@fujixerox.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing checks for dma mapping error in qset_fill_page_list(),
I have missed two similar problems in qset_add_urb_sg() and
in qset_add_urb_sg_linearize().
v2: check validity of dma_addr with dma_mapping_error()
in qset_free_std() as suggested by Vladimir Zapolskiy.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 0.95 xHCI spec says that non-control endpoints will be halted if a
babble is detected on a transfer. The 0.96 xHCI spec says all types of
endpoints will be halted when a babble is detected. Some hardware that
claims to be 0.95 compliant halts the control endpoint anyway.
Reference: http://www.spinics.net/lists/linux-usb/msg21755.html
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We *know* that we have 1 PAGE (4096 bytes) for our
TRB poll. We also know the size of each TRB and know
that we can fit 256 of them in one PAGE. By using a
u8 type we can make sure that:
enqueue++ % 256;
gets optimized to an increment only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This makes it clear that we're dealing with a queue
of TRBs. No functional changes. While at that, also
rename start_slot to first_trb_index for similar
reasons.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The DWC3 OMAP driver supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-omap.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some freescale QorIQ platforms require to disable receiver detection
in P3 for correct detection of USB devices. If GUSB3PIPECTL(DISRXDETINP3)
is set, Core will change PHY power state to P2 and then perform receiver
detection. After receiver detection, Core will change PHY power state to
P3. Same quirk would be added in dts file in future patches.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook says we should move link to U0
before issuing a Start Transfer command. We could
require the gadget driver to call
usb_gadget_wakeup() however I feel that changing all
gadget drivers to keep track of Link State and
conditionally call usb_gadget_wakeup() would be far
too much work. For now we will handle this at the
UDC level, but at some point composite.c should be
one handling this.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Synopsys Databook 2.60a has a note that if we're
sending an endpoint command we _must_ make sure that
DWC3_GUSB2PHY(n).SUSPHY bit is cleared.
This patch implements that particular detail.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_send_gadget_ep_cmd() had three return
points. That becomes a pain to track when we need to
debug something or if we need to add more code
before returning.
Let's combine all three return points into a single
one just by introducing a local 'ret' variable.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sort IDs in groups to be easily found when needed.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It seems there are leftovers of some assignments which are not used
anymore. Compiler even warns us about:
drivers/usb/gadget/udc/pch_udc.c:2022:22: warning: variable ‘dev’ set \
but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/pch_udc.c:2639:9: warning: variable ‘ret’ set \
but not used [-Wunused-but-set-variable]
Remove them and shut compiler about.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Try to enable MSI in case hardware supports it. At least Intel Quark is
known SoC which indeed does.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devres API allows to make error paths cleaner and less error
prone. Convert the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no need to repeat the work that is already done in the PCI
driver core. The patch removes excerpts from suspend and resume
callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
While here, convert PM ops to use modern API.
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[felipe.balbi@linux.intel.com: fixed build break and checkpatch error ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The phy-am335x driver selects 'USB_COMMON', but all other drivers
use 'depends on' for that symbol, and it depends on USB || USB_GADGET
itself, which causes a Kconfig warning:
warning: (AM335X_PHY_USB) selects USB_COMMON which has unmet direct dependencies (USB_SUPPORT && (USB || USB_GADGET))
As suggested by Felipe Balbi, this turns the logic around, and makes
'USB_COMMON' selected by everything else that needs it, so we can
remove the dependencies.
Fixes: 59f042f644 ("usb: phy: phy-am335x: bypass first VBUS sensing for host-only mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we don't plan on using multiple event buffers, but
if we find a good use case for it, this little trick
will help us avoid a loop in hardirq handler looping
for each and every event buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget controller might not be always active during system
suspend/resume as gadget driver might not have yet been loaded or
might have been unloaded prior to system suspend.
Check if we're active and only then perform
necessary actions during suspend/resume.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc->regset is allocated on dwc3_debugfs_init, and should
be released on init failure or dwc3_debugfs_exit. Btw,
The line "dwc->root = NULL" is unnecessary, so remove it.
Signed-off-by: Du, Changbin <changbin.du@intel.com>
[ felipe.balbi@linux.intel.com : add another err label for the new
error condition ]
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
we need to power off the PHY during suspend and
power it back on during resume.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: fix call to usb_phy_set_suspend() in dwc3_suspend()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even if pm_runtime_get*() fails, we *MUST* call
pm_runtime_put_sync() before disabling PM.
While at it, remove superfluous dwc3_omap_disable_irqs()
in error path.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[nsekhar@ti.com: patch description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set the reserved fields of the SuperSpeed Plus Device Capability
descriptor to 0. Otherwise there might be stale data there which will
cause USB CV to fail.
Fixes: f228a8de24 ("usb: gadget: composite: Return SSP Dev Cap descriptor")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
we will be using a single event buffer and that
renders ev_buffs array unnecessary. Let's remove it
in favor of a single pointer to a single event
buffer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We never, ever route any of the other event buffers
so we might as well drop support for them.
Until someone has a real, proper benefit for
multiple event buffers, we will rely on a single
one. This also helps reduce memory footprint of
dwc3.ko which won't allocate memory for the extra
event buffers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
coccicheck found this pattern which could be
converted to PTR_ERR_OR_ZERO(). No functional
changes.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
request_list and req_queued were, well, weird naming
choices.
Let's give those better names and call them,
respectively, pending_list and started_list. These
new names better reflect what these lists are
supposed to do.
While at that also rename req->queued to req->started.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
previously we were using a maximum of 32 TRBs per
endpoint. With each TRB being 16 bytes long, we were
using 512 bytes of memory for each endpoint.
However, SLAB/SLUB will always allocate PAGE_SIZE
chunks. In order to better utilize the memory we
allocate and to allow deeper queues for gadgets
which would benefit from it (g_ether comes to mind),
let's increase the maximum to 256 TRBs which rounds
up to 4096 bytes for each endpoint.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
CSP bit of TRB Control is useful for protocols such
CDC EEM/ECM/NCM where we're transferring in blocks
of MTU-sized requests (usually MTU is 1500 bytes).
We know we will always have a short packet after two
(for HS) wMaxPacketSize packets and, usually, we
will have a long(-ish) queue of requests (for our
g_ether gadget, we have at least 10
requests).
Instead of always stopping the queue processing to
interrupt, giveback and restart, let's tell dwc3 to
interrupt but continue processing following request
if we have anything already pending in the queue.
This gave me a considerable improvement of 40% on my
test setup.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
That FIFO resizing logic was added to support OMAP5
ES1.0 which had a bogus default FIFO size. I can't
remember the exact size of default FIFO, but it was
less than one bulk superspeed packet (<1024) which
would prevent USB3 from ever working on OMAP5 ES1.0.
However, OMAP5 ES1.0 support has been dropped by
commit aa2f4b16f8 ("ARM: OMAP5: id: Remove ES1.0
support") which renders FIFO resizing unnecessary.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On BXT platform Host Controller and Device Controller figure as
same PCI device but with different device function. HCD should
not pass data to Device Controller but only to Host Controllers.
Checking if companion device is Host Controller, otherwise skip.
Cc: <stable@vger.kernel.org>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new NO_REPORT_LUNS quirk and set it for Seagate drives with
an usb-id of: 0bc2:331a, as these will fail to respond to a
REPORT_LUNS command.
Cc: stable@vger.kernel.org
Reported-and-tested-by: David Webb <djw@noc.ac.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 64d513ac31 ("scsi: use host wide tags by default") causes
the SCSI core to queue more commands then we can handle on devices with
multiple LUNs, limit the queue depth at the scsi-host level instead of
per slave to fix this.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1315013
Cc: stable@vger.kernel.org # 4.4.x and 4.5.x
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise generic-xhci and xhci-platform which have no data get wrongly
detected as XHCI_PLAT_TYPE_MARVELL_ARMADA by xhci_plat_type_is().
This fixes a regression in v4.5 for STiH407 family SoC's which use the
synopsis dwc3 IP, whereby the disable_clk error path gets taken due to
wrongly being detected as XHCI_PLAT_TYPE_MARVELL_ARMADA and the hcd never
gets added.
I suspect this will also fix other dwc3 DT platforms such as Exynos,
although I've only tested on STih410 SoC.
Fixes: 4efb2f6941 ("usb: host: xhci-plat: add struct xhci_plat_priv")
Cc: stable@vger.kernel.org
Cc: gregory.clement@free-electrons.com
Cc: yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI hotpluggable xhci controllers such as some Alpine Ridge solutions will
remove the xhci controller from the PCI bus when the last USB device is
disconnected.
Add a flag to indicate that the host is being removed to avoid queueing
configure_endpoint commands for the dropped endpoints.
For PCI hotplugged controllers this will prevent 5 second command timeouts
For static xhci controllers the configure_endpoint command is not needed
in the removal case as everything will be returned, freed, and the
controller is reset.
For now the flag is only set for PCI connected host controllers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes some wild pointers produced by xhci_mem_cleanup.
These wild pointers will cause system crash if xhci_mem_cleanup()
is called twice.
Reported-and-tested-by: Pengcheng Li <lpc.li@hisilicon.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue that cannot work if R-Car Gen2/3 run on
above 4GB physical memory environment to use a quirk XHCI_NO_64BIT_SUPPORT.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some xHCI controllers (e.g. R-Car SoCs), the AC64 bit (bit 0) of
HCCPARAMS1 is set to 1. However, the xHCs don't support 64-bit
address memory pointers actually. So, in this case, this driver should
call dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) in xhci_gen_setup().
Otherwise, the xHCI controller will be died after a usb device is
connected if it runs on above 4GB physical memory environment.
So, this patch adds a new quirk XHCI_NO_64BIT_SUPPORT to resolve
such an issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Give USB3 devices a better chance to enumerate at USB 3 speeds if
they are connected to a suspended host.
Solves an issue with NEC uPD720200 host hanging when partially
enumerating a USB3 device as USB2 after host controller runtime resume.
Cc: <stable@vger.kernel.org>
Tested-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Broxton B0 also requires XHCI_PME_STUCK_QUIRK.
Adding PCI device ID for Broxton B and adding to quirk.
Cc: <stable@vger.kernel.org>
Signed-off-by: Rafal Redzimski <rafal.f.redzimski@intel.com>
Signed-off-by: Robert Dobrowolski <robert.dobrowolski@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under some circumstances acm_tty_flush_chars() is called
with no buffer to flush. We simply need to do nothing.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as they
are "trivial".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcJLLUACgkQMUfUDdst+ym3wgCeNSzb74ZskDbGsXUooE0XhYRc
iPoAnRpn/ahoBTzmkKiQXQ1+Br8pAUtN
=vyU/
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vUqa
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.6-rc3
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
We have two more fixes to f_midi. It should now
behave much better.
dwc3-keystone.c has gotten a fix which now allows it
to work on keystone device when running in
peripheral mode. A similar fix for DMA configuration
was made for udc-core, too.
We have a new PCI ID for Intel's Broxton
platform. DWC3 can run on those platforms as well.
And we also have some dwc2 got a fix for dr_mode
usage, while renesas controller got 3 important
fixes: a NULL pointer deref fix, IRQ <-> DMA race
fix, and a fix to prevent a situation where we would
queue a request to a disabled endpoint.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QLLF
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.6-rc3
We have two more fixes to f_midi. It should now
behave much better.
dwc3-keystone.c has gotten a fix which now allows it
to work on keystone device when running in
peripheral mode. A similar fix for DMA configuration
was made for udc-core, too.
We have a new PCI ID for Intel's Broxton
platform. DWC3 can run on those platforms as well.
And we also have some dwc2 got a fix for dr_mode
usage, while renesas controller got 3 important
fixes: a NULL pointer deref fix, IRQ <-> DMA race
fix, and a fix to prevent a situation where we would
queue a request to a disabled endpoint.
The CP2105 is used in the GE Healthcare Remote Alarm Box, with the
Manufacturer ID of 0x1901 and Product ID of 0x0194.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A Fedora user reports that the ftdi_sio driver works properly for the
ICP DAS I-7561U device. Further, the user manual for these devices
instructs users to load the driver and add the ids using the sysfs
interface.
Add support for these in the driver directly so that the devices work
out of the box instead of needing manual configuration.
Reported-by: <thesource@mail.ru>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit 7ace8fc821 ("usb: gadget: udc: core: Fix argument of
dma_map_single for IOMMU") it is not necessary to configure DMA for
usb_gadget device manually, because all DMA operation are performed
using parent/controller device.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
BXT-M is a Intel Broxton SoC based platform with unique PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move the state_changed variable into struct otg_fsm
so that we can support multiple instances.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
For each platform devices which is created by device tree, the default
DMA mask is set by of_dma_configure when the device are created. So
delete the redundant code at driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes an issue that usbhsg_queue_done() may cause kernel
panic when dma callback is running and usb_ep_disable() is called
by interrupt handler. (Especially, we can reproduce this issue using
g_audio with usb-dmac driver.)
For example of a flow:
usbhsf_dma_complete (on tasklet)
--> usbhsf_pkt_handler (on tasklet)
--> usbhsg_queue_done (on tasklet)
*** interrupt happened and usb_ep_disable() is called ***
--> usbhsg_queue_pop (on tasklet)
Then, oops happened.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The host/device mode set with dr_mode should be kept all the time,
not being changed to OTG in gadget setup (by overriding CFGUSB_FORCEDEVMODE
and CFGUSB_FORCEHOSTMODE bits).
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Przemek Rudy <prudy1@o2.pl>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We added some new locking here, but missed an error path where we need
to unlock.
Fixes: 9acdf4df2f ('usb: gadget: f_midi: added spinlock on transmit function')
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver can be crashed with devices that expose crafted descriptors
with too few endpoints.
See: http://seclists.org/bugtraq/2016/Mar/61
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
[johan: fix OOB endpoint check and add error messages ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An attack using the lack of sanity checking in probe is known. This
patch checks for the existence of a second port.
CVE-2016-3136
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
[johan: add error message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b37d83a6a4 ("usb: Parse the new USB 3.1 SuperSpeedPlus Isoc
endpoint companion descriptor") caused a regression in 4.6-rc1 and fails
to parse SuperSpeed endpoint companion descriptors.
The new SuperSpeedPlus Isoc endpoint companion parsing code incorrectly
decreased the the remaining buffer size before comparing the size with the
expected length of the descriptor.
This lead to possible failure in reading the SuperSpeed endpoint companion
descriptor of the last endpoint, displaying a message like:
"No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0
ep 129: using minimum values"
Fix it by decreasing the size after comparing it.
Also finish all the SS endpoint companion parsing before calling SSP isoc
endpoint parsing function.
Fixes: b37d83a6a4
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential out-of-bounds write to urb->transfer_buffer
usbip handles network communication directly in the kernel. When receiving a
packet from its peer, usbip code parses headers according to protocol. As
part of this parsing urb->actual_length is filled. Since the input for
urb->actual_length comes from the network, it should be treated as untrusted.
Any entity controlling the network may put any value in the input and the
preallocated urb->transfer_buffer may not be large enough to hold the data.
Thus, the malicious entity is able to write arbitrary data to kernel memory.
Signed-off-by: Ignat Korchagin <ignat.korchagin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a code to surely disable TX IRQ of the pipe before
starting TX DMAC transfer. Otherwise, a lot of unnecessary TX IRQs
may happen in rare cases when DMAC is used.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
buflen by default (256) is smaller than wMaxPacketSize (512) in high-speed
devices.
That caused the OUT endpoint to freeze if the host send any data packet of
length greater than 256 bytes.
This is an example dump of what happended on that enpoint:
HOST: [DATA][Length=260][...]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
...
HOST: [PING]
DEVICE: [NAK]
This patch fixes this problem by setting the minimum usb_request's buffer size
for the OUT endpoint as its wMaxPacketSize.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
gcc warns about the use of regulators in phy_8x16_probe:
drivers/usb/phy/phy-qcom-8x16-usb.c: In function 'phy_8x16_probe':
drivers/usb/phy/phy-qcom-8x16-usb.c:284:13: error: 'regs[0].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/usb/phy/phy-qcom-8x16-usb.c:285:13: error: 'regs[1].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/usb/phy/phy-qcom-8x16-usb.c:286:12: error: 'regs[2].consumer' may be used uninitialized in this function [-Werror=maybe-uninitialized]
According to Mark Brown, this is the result of various abuses
of the PHY interfaces [1], so let's fix the driver instead.
This puts the regulator bulk data into the device structure so it
gets properly initialized and lets us call regulator_bulk_enable()
and regulator_bulk_disable() rather than open-coding them.
Setting the voltages the way the driver does is rather pointless
because for each regulator there is only one valid voltage
range, so that can just get set up in the DT. As there doesn't
seem to be any user of the newly added driver yet, we can simply
make sure the DTs are setting this up right when they get added.
I'm also fixing the handling of regulator_bulk_enable() failure.
Right now, the driver just ignores any failure, which doesn't make
sense, so I'm changing it to loudly complain (in case we actually
had a bug here) and error out.
Doing a fly-by review of the driver, I notice a couple of other
problems that I'm not addressing here:
- It really should not have been written as a USB PHY driver, but
instead should use the PHY subsystem.
- The DT compatible string does not follow the usual conventions,
and it should have a proper identifier in it rather than a wildcard.
- The example in the devicetree binding lists a register address
that is the same as the actual EHCI host controller in the SoC
as well as the otg-snps and the ci-hdrc device, which indicates
that these are probably not even distinct devices (or all but
one of them are wrong), and if more than one of them tries to
request the resources correctly, they fail.
[1] https://lkml.org/lkml/2016/1/26/267
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Access multi-byte fields of the SSP Dev Cap descriptor using the correct
endianness.
Fixes: f228a8de24 ("usb: gadget: composite: Return SSP Dev Cap descriptor")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UDC driver should NEVER do anything behind
udc-core's back, so let's stop disabling endpoints
we don't exactly own - rather we provide as
resources for gadget drivers. This fixes the
regression reported by Gil.
Reported-by: Gil Weber <gil.weber@servelec-technologies.com>
Tested-by: Gil Weber <gil.weber@servelec-technologies.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We were exitting the function before actually
renaming anything. While at that, also always leave
control endpoint un-renamed.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's a requirement that we release controller's lock
while calling gadget API function pointers. This
patch just fixes that long standing bug.
Signed-off-by: Jiebing Li <jiebing.li@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook, we shouldn't be
relying on GCTL.CORESOFTRESET bit as that's only for
debugging purposes. Instead, let's use DCTL.CSFTRST
if we're OTG or PERIPHERAL mode.
Host side block will be reset by XHCI driver if
necessary. Note that this reduces amount of time
spent on dwc3_probe() by a long margin.
We're still gonna wait for reset to finish for a
long time (default to 1ms max), but tests show that
the reset polling loop executed at most 19 times
(modprobe dwc3 && modprobe -r dwc3 executed 1000
times in a row).
Suggested-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since f_midi_transmit is called by both ALSA and USB sub-systems, it can
potentially cause a race condition between both calls because f_midi_transmit
is not reentrant nor thread-safe. This is due to an implementation detail that
the transmit function looks for the next available usb request from the fifo
and only enqueues it if there is data to send, otherwise just re-uses it. So,
if both ALSA and USB frameworks calls this function at the same time,
kfifo_seek() will return the same usb_request, which will cause a race
condition.
To solve this problem a syncronization mechanism is necessary. In this case it
is used a spinlock since f_midi_transmit is also called by usb_request->complete
callback in interrupt context.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: e1e3d7ec5d ("usb: gadget: f_midi: pre-allocate IN requests")
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
new device support in terms of LoC, but there has been some cleanup
in the core as well as the usual minor clk additions to various
drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a minor
refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bZFY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The clk changes for this release cycle are mostly dominated by new
device support in terms of LoC, but there has been some cleanup in the
core as well as the usual minor clk additions to various drivers.
Core:
- parent tracking has been simplified
- CLK_IS_ROOT is now a no-op flag, cleaning up drivers has started
- of_clk_init() doesn't consider disabled DT nodes anymore
- clk_unregister() had an error path bug squashed
- of_clk_get_parent_count() has been fixed to only return unsigned ints
- HAVE_MACH_CLKDEV is removed now that the last arch user (ARM) is gone
New Drivers:
- NXP LPC18xx creg
- QCOM IPQ4019 GCC
- TI dm814x ADPLL
- i.MX6QP
Updates:
- Cyngus audio clks found on Broadcom iProc devices
- Non-critical fixes for BCM2385 PLLs
- Samsung exynos5433 updates for clk id errors, HDMI support,
suspend/resume simplifications
- USB, CAN, LVDS, and FCP clks on shmobile devices
- sunxi got support for more clks on new SoCs and went through a
minor refactoring/rewrite to use a simpler factor clk construct
- rockchip added some more clk ids and added suport for fraction
dividers
- QCOM GDSCs in msm8996
- A new devm helper to make adding custom actions simpler (acked by Greg)"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (197 commits)
clk: bcm2835: fix check of error code returned by devm_ioremap_resource()
clk: renesas: div6: use RENESAS for #define
clk: renesas: Rename header file renesas.h
clk: max77{686,802}: Remove CLK_IS_ROOT
clk: versatile: Remove CLK_IS_ROOT
clk: sunxi: Remove use of variable length array
clk: fixed-rate: Remove CLK_IS_ROOT
clk: qcom: Remove CLK_IS_ROOT
doc: dt: add documentation for lpc1850-creg-clk driver
clk: add lpc18xx creg clk driver
clk: lpc32xx: fix compilation warning
clk: xgene: Add missing parenthesis when clearing divider value
clk: mb86s7x: Remove CLK_IS_ROOT
clk: x86: Remove clkdev.h and clk.h includes
clk: x86: Remove CLK_IS_ROOT
clk: mvebu: Remove CLK_IS_ROOT
clk: renesas: move drivers to renesas directory
clk: si5{14,351,70}: Remove CLK_IS_ROOT
clk: scpi: Remove CLK_IS_ROOT
clk: s2mps11: Remove CLK_IS_ROOT
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Add target_alloc_session() w/ callback helper for doing se_session
allocation + tag + se_node_acl lookup. (HCH + nab)
- Tree-wide fabric driver conversion to use target_alloc_session()
- Convert sbp-target to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Chris Boot + nab)
- Convert usb-gadget to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Andrzej Pietrasiewicz + nab)
- Convert xen-scsiback to use percpu_ida tag pre-allocation, and
TARGET_SCF_ACK_KREF I/O krefs (Juergen Gross + nab)
- Convert tcm_fc to use TARGET_SCF_ACK_KREF I/O + TMR krefs
- Convert ib_srpt to use percpu_ida tag pre-allocation
- Add DebugFS node for qla2xxx target sess list (Quinn)
- Rework iser-target connection termination (Jenny + Sagi)
- Convert iser-target to new CQ API (HCH)
- Add pass-through WRITE_SAME support for IBLOCK (Mike Christie)
- Introduce data_bitmap for asynchronous access of data area (Sheng
Yang + Andy)
- Fix target_release_cmd_kref shutdown comp leak (Himanshu Madhani)
Also, there is a separate PULL request coming for cxgb4 NIC driver
prerequisites for supporting hw iscsi segmentation offload (ISO), that
will be the base for a number of v4.7 developments involving
iscsi-target hw offloads"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
target: Fix target_release_cmd_kref shutdown comp leak
target: Avoid DataIN transfers for non-GOOD SAM status
target/user: Report capability of handling out-of-order completions to userspace
target/user: Fix size_t format-spec build warning
target/user: Don't free expired command when time out
target/user: Introduce data_bitmap, replace data_length/data_head/data_tail
target/user: Free data ring in unified function
target/user: Use iovec[] to describe continuous area
target: Remove enum transport_lunflags_table
target/iblock: pass WRITE_SAME to device if possible
iser-target: Kill the ->isert_cmd back pointer in struct iser_tx_desc
iser-target: Kill struct isert_rdma_wr
iser-target: Convert to new CQ API
iser-target: Split and properly type the login buffer
iser-target: Remove ISER_RECV_DATA_SEG_LEN
iser-target: Remove impossible condition from isert_wait_conn
iser-target: Remove redundant wait in release_conn
iser-target: Rework connection termination
iser-target: Separate flows for np listeners and connections cma events
iser-target: Add new state ISER_CONN_BOUND to isert_conn
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition
of a MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HS4G
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons:
- Rockchip rk3368 gains power domain support
- Small updates for the ARM spmi driver
- The Atmel PMC driver saw a larger rework, touching both
arch/arm/mach-at91 and drivers/clk/at91
- All reset controller driver changes alway get merged through
arm-soc, though this time the largest change is the addition of a
MIPS pistachio reset driver
- One bugfix for the NXP (formerly Freescale) i.MX weim bus driver"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
bus: imx-weim: Take the 'status' property value into account
clk: at91: remove useless includes
clk: at91: pmc: remove useless capacities handling
clk: at91: pmc: drop at91_pmc_base
usb: gadget: atmel: access the PMC using regmap
ARM: at91: remove useless includes and function prototypes
ARM: at91: pm: move idle functions to pm.c
ARM: at91: pm: find and remap the pmc
ARM: at91: pm: simply call at91_pm_init
clk: at91: pmc: move pmc structures to C file
clk: at91: pmc: merge at91_pmc_init in atmel_pmc_probe
clk: at91: remove IRQ handling and use polling
clk: at91: make use of syscon/regmap internally
clk: at91: make use of syscon to share PMC registers in several drivers
hwmon: (scpi) add energy meter support
firmware: arm_scpi: add support for 64-bit sensor values
firmware: arm_scpi: decrease Tx timeout to 20ms
firmware: arm_scpi: fix send_message and sensor_get_value for big-endian
reset: sti: Make reset_control_ops const
reset: zynq: Make reset_control_ops const
...
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
Here is a USB fix for the reported issue with 69bec72598 "USB: core:
let USB device know device node" as well as some other issues that have
been reported so far with this merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbsjB8ACgkQMUfUDdst+yn5BACeK0uVt+S/pr+HQE30j67b4UV6
TcMAn25xKshM73AFDm9ok9qKnWEEvkEt
=UgYu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a USB fix for the reported issue with commit 69bec72598
("USB: core: let USB device know device node") as well as some other
issues that have been reported so far with this merge window"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: uas: Reduce can_queue to MAX_CMNDS
USB: cdc-acm: more sanity checking
USB: usb_driver_claim_interface: add sanity checking
usb/core: usb_alloc_dev(): fix setting of ->portnum
USB: iowarrior: fix oops with malicious USB descriptors
The uas driver can never queue more then MAX_CMNDS (- 1) tags and tags
are shared between luns, so there is no need to claim that we can_queue
some random large number.
Not claiming that we can_queue 65536 commands, fixes the uas driver
failing to initialize while allocating the tag map with a "Page allocation
failure (order 7)" error on systems which have been running for a while
and thus have fragmented memory.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Yves-Alexis Perez <corsac@corsac.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An attack has become available which pretends to be a quirky
device circumventing normal sanity checks and crashes the kernel
by an insufficient number of interfaces. This patch adds a check
to the code path for quirky devices.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Attacks that trick drivers into passing a NULL pointer
to usb_driver_claim_interface() using forged descriptors are
known. This thwarts them by sanity checking.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iowarrior driver expects at least one valid endpoint. If given
malicious descriptors that specify 0 for the number of endpoints,
it will crash in the probe function. Ensure there is at least
one endpoint on the interface before using it.
The full report of this issue can be found here:
http://seclists.org/bugtraq/2016/Mar/87
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
- A large patch from me to simplify setting up the list of default
groups by actually implementing it as a list instead of an array.
- a small Y2083 prep patch from Deepa Dinamani. Probably doesn't matter
on it's own, but it seems like he is trying to get rid of all CURRENT_TIME
uses in file systems, which is a worthwhile goal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9HqT
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
- A large patch from me to simplify setting up the list of default
groups by actually implementing it as a list instead of an array.
- a small Y2083 prep patch from Deepa Dinamani. Probably doesn't
matter on it's own, but it seems like he is trying to get rid of all
CURRENT_TIME uses in file systems, which is a worthwhile goal.
* tag 'configfs-for-linus' of git://git.infradead.org/users/hch/configfs:
configfs: switch ->default groups to a linked list
configfs: Replace CURRENT_TIME by current_fs_time()
The new helper returns index of the mathing string in an array. We
would use it here.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots of
other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8/EACgkQMUfUDdst+ylsyQCgnVK6ZIFVPV9VijJvBIjxS3F+
fTMAoIMQwNrRMHQOq/lhxX00AgN0B9Ch
=2EQp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots
of other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (266 commits)
USB: core: let USB device know device node
usb: devio: Add ioctl to disallow detaching kernel USB drivers.
usb: gadget: f_acm: Fix configfs attr name
usb: udc: lpc32xx: remove USB PLL and USB OTG clock management
usb: udc: lpc32xx: remove direct access to clock controller registers
usb: udc: lpc32xx: switch to clock prepare/unprepare model
usb: renesas_usbhs: gadget: fix giveback status code in usbhsg_pipe_disable()
usb: gadget: renesas_usb3: Use ARCH_RENESAS
usb: dwc2: Fix issues in dwc2_complete_non_isoc_xfer_ddma()
usb: dwc2: Add support for Lantiq ARX and XRX SoCs
usb: phy: generic: Handle late registration of gadget
usb: gadget: bdc_udc: fix race condition in bdc_udc_exit()
usb: musb: core: added missing const qualifier to musb_hdrc_platform_data::config
usb: dwc2: Move host-specific core functions into hcd.c
usb: dwc2: Move register save and restore functions
usb: dwc2: Use kmem_cache_free()
usb: dwc2: host: If using uframe scheduler, end splits better
usb: dwc2: host: Totally redo the microframe scheduler
usb: dwc2: host: Properly set even/odd frame
usb: dwc2: host: Add dwc2_hcd_get_future_frame_number() call
...
Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8z8ACgkQMUfUDdst+ym1vwCgnOOCORaZyeQ4QrcxPAK5pHFn
VrMAoNHvDgNYtG+Hmzv25Lgp3HnysPin
=MLRG
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver pull request for 4.6-rc1.
Lots of changes in here, Peter has been on a tear again, with lots of
refactoring and bugs fixes, many thanks to the great work he has been
doing. Lots of driver updates and fixes as well, full details in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (220 commits)
serial: 8250: describe CONFIG_SERIAL_8250_RSA
serial: samsung: optimize UART rx fifo access routine
serial: pl011: add mark/space parity support
serial: sa1100: make sa1100_register_uart_fns a function
tty: serial: 8250: add MOXA Smartio MUE boards support
serial: 8250: convert drivers to use up_to_u8250p()
serial: 8250/mediatek: fix building with SERIAL_8250=m
serial: 8250/ingenic: fix building with SERIAL_8250=m
serial: 8250/uniphier: fix modular build
Revert "drivers/tty/serial: make 8250/8250_ingenic.c explicitly non-modular"
Revert "drivers/tty/serial: make 8250/8250_mtk.c explicitly non-modular"
serial: mvebu-uart: initial support for Armada-3700 serial port
serial: mctrl_gpio: Add missing module license
serial: ifx6x60: avoid uninitialized variable use
tty/serial: at91: fix bad offset for UART timeout register
tty/serial: at91: restore dynamic driver binding
serial: 8250: Add hardware dependency to RT288X option
TTY, devpts: document pty count limiting
tty: goldfish: support platform_device with id -1
drivers: tty: goldfish: Add device tree bindings
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.6:
API:
- Convert remaining crypto_hash users to shash or ahash, also convert
blkcipher/ablkcipher users to skcipher.
- Remove crypto_hash interface.
- Remove crypto_pcomp interface.
- Add crypto engine for async cipher drivers.
- Add akcipher documentation.
- Add skcipher documentation.
Algorithms:
- Rename crypto/crc32 to avoid name clash with lib/crc32.
- Fix bug in keywrap where we zero the wrong pointer.
Drivers:
- Support T5/M5, T7/M7 SPARC CPUs in n2 hwrng driver.
- Add PIC32 hwrng driver.
- Support BCM6368 in bcm63xx hwrng driver.
- Pack structs for 32-bit compat users in qat.
- Use crypto engine in omap-aes.
- Add support for sama5d2x SoCs in atmel-sha.
- Make atmel-sha available again.
- Make sahara hashing available again.
- Make ccp hashing available again.
- Make sha1-mb available again.
- Add support for multiple devices in ccp.
- Improve DMA performance in caam.
- Add hashing support to rockchip"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (116 commits)
crypto: qat - remove redundant arbiter configuration
crypto: ux500 - fix checks of error code returned by devm_ioremap_resource()
crypto: atmel - fix checks of error code returned by devm_ioremap_resource()
crypto: qat - Change the definition of icp_qat_uof_regtype
hwrng: exynos - use __maybe_unused to hide pm functions
crypto: ccp - Add abstraction for device-specific calls
crypto: ccp - CCP versioning support
crypto: ccp - Support for multiple CCPs
crypto: ccp - Remove check for x86 family and model
crypto: ccp - memset request context to zero during import
lib/mpi: use "static inline" instead of "extern inline"
lib/mpi: avoid assembler warning
hwrng: bcm63xx - fix non device tree compatibility
crypto: testmgr - allow rfc3686 aes-ctr variants in fips mode.
crypto: qat - The AE id should be less than the maximal AE number
lib/mpi: Endianness fix
crypto: rockchip - add hash support for crypto engine in rk3288
crypto: xts - fix compile errors
crypto: doc - add skcipher API documentation
crypto: doc - update AEAD AD handling
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tPgH
-----END PGP SIGNATURE-----
Merge tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Added support for some new video formats
- mn88473 DVB frontend driver got promoted from staging
- several improvements at the VSP1 driver
- several cleanups and improvements at the Media Controller
- added Media Controller support to snd-usb-audio. Currently, enabled
only for au0828-based V4L2/DVB boards
- Several improvements at nuvoton-cir: it now supports wake up codes
- Add media controller support to em28xx and saa7134 drivers
- coda driver now accepts NXP distributed firmware files
- Some legacy SoC camera drivers will be moving to staging, as they're
outdated and nobody so far is willing to fix and convert them to use
the current media framework
- As usual, lots of cleanups, improvements and new board additions.
* tag 'media/v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (381 commits)
media: au0828 disable tuner to demod link in au0828_media_device_register()
[media] touptek: cast char types on %x printk
[media] touptek: don't DMA at the stack
[media] mceusb: use %*ph for small buffer dumps
[media] v4l: exynos4-is: Drop unneeded check when setting up fimc-lite links
[media] v4l: vsp1: Check if an entity is a subdev with the right function
[media] hide unused functions for !MEDIA_CONTROLLER
[media] em28xx: fix Terratec Grabby AC97 codec detection
[media] media: add prefixes to interface types
[media] media: rc: nuvoton: switch attribute wakeup_data to text
[media] v4l2-ioctl: fix YUV422P pixel format description
[media] media: fix null pointer dereference in v4l_vb2q_enable_media_source()
[media] v4l2-mc.h: fix yet more compiler errors
[media] staging/media: add missing TODO files
[media] media.h: always start with 1 for the audio entities
[media] sound/usb: Use meaninful names for goto labels
[media] v4l2-mc.h: fix compiler warnings
[media] media: au0828 audio mixer isn't connected to decoder
[media] sound/usb: Use Media Controller API to share media resources
[media] dw2102: add support for TeVii S662
...
PCI-SIG has defined Interface FEh for Base Class 0Ch, Sub-Class 03h as "USB
Device (not host controller)". It is already being used in various USB
device controller drivers for matching, so add PCI_CLASS_SERIAL_USB_DEVICE
and use it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* commit '840f5b0572ea': (381 commits)
media: au0828 disable tuner to demod link in au0828_media_device_register()
[media] touptek: cast char types on %x printk
[media] touptek: don't DMA at the stack
[media] mceusb: use %*ph for small buffer dumps
[media] v4l: exynos4-is: Drop unneeded check when setting up fimc-lite links
[media] v4l: vsp1: Check if an entity is a subdev with the right function
[media] hide unused functions for !MEDIA_CONTROLLER
[media] em28xx: fix Terratec Grabby AC97 codec detection
[media] media: add prefixes to interface types
[media] media: rc: nuvoton: switch attribute wakeup_data to text
[media] v4l2-ioctl: fix YUV422P pixel format description
[media] media: fix null pointer dereference in v4l_vb2q_enable_media_source()
[media] v4l2-mc.h: fix yet more compiler errors
[media] staging/media: add missing TODO files
[media] media.h: always start with 1 for the audio entities
[media] sound/usb: Use meaninful names for goto labels
[media] v4l2-mc.h: fix compiler warnings
[media] media: au0828 audio mixer isn't connected to decoder
[media] sound/usb: Use Media Controller API to share media resources
[media] dw2102: add support for TeVii S662
...
This patch drops struct usbg_cmd->kref internal kref-erence
usage, for proper TARGET_SCF_ACK_KREF conversion.
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts usb-gadget target to use percpu_ida tag
pre-allocation for struct usbg_cmd descriptor, in order to
avoid fast-path struct usbg_cmd memory allocations.
Note by default this is currently hardcoded to 128.
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts existing loopback, usb-gadget, and
xen-scsiback demo-mode only fabric drivers to use the
new target_alloc_session API caller.
This includes adding a new alloc_session callback for
fabric driver internal nexus pointer assignments.
(Fixes for early for-next nexus breakage - Dan Carpenter)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Acked-by: Juergen Gross <jgross@suse.com>
Tested-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Tested-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here are some cp210x register-accessor updates and general usb-serial
code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=9QeZ
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.6-rc1
Here are some cp210x register-accessor updates and general usb-serial
code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
Replace the current NULL-terminated array of default groups with a linked
list. This gets rid of lots of nasty code to size and/or dynamically
allocate the array.
While we're at it also provide a conveniant helper to remove the default
groups.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Felipe Balbi <balbi@kernel.org> [drivers/usb/gadget]
Acked-by: Joel Becker <jlbec@evilplan.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Although most of USB devices are hot-plug's, there are still some devices
are hard wired on the board, eg, for HSIC and SSIC interface USB devices.
If these kinds of USB devices are multiple functions, and they can supply
other interfaces like i2c, gpios for other devices, we may need to
describe these at device tree.
In this commit, it uses "reg" in dts as physical port number to match
the phyiscal port number decided by USB core, if they are the same,
then the device node is for the device we are creating for USB core.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new USBDEVFS_DROP_PRIVILEGES ioctl allows a process to voluntarily
relinquish the ability to issue other ioctls that may interfere with
other processes and drivers that have claimed an interface on the
device.
This commit also includes a simple utility to be able to test the
ioctl, located at Documentation/usb/usbdevfs-drop-permissions.c
Example (with qemu-kvm's input device):
$ lsusb
...
Bus 001 Device 002: ID 0627:0001 Adomax Technology Co., Ltd
$ usb-devices
...
C: #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=02 Driver=usbhid
$ sudo ./usbdevfs-drop-permissions /dev/bus/usb/001/002
OK: privileges dropped!
Available options:
[0] Exit now
[1] Reset device. Should fail if device is in use
[2] Claim 4 interfaces. Should succeed where not in use
[3] Narrow interface permission mask
Which option shall I run?: 1
ERROR: USBDEVFS_RESET failed! (1 - Operation not permitted)
Which test shall I run next?: 2
ERROR claiming if 0 (1 - Operation not permitted)
ERROR claiming if 1 (1 - Operation not permitted)
ERROR claiming if 2 (1 - Operation not permitted)
ERROR claiming if 3 (1 - Operation not permitted)
Which test shall I run next?: 0
After unbinding usbhid:
$ usb-devices
...
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=02 Driver=(none)
$ sudo ./usbdevfs-drop-permissions /dev/bus/usb/001/002
...
Which option shall I run?: 2
OK: claimed if 0
ERROR claiming if 1 (1 - Operation not permitted)
ERROR claiming if 2 (1 - Operation not permitted)
ERROR claiming if 3 (1 - Operation not permitted)
Which test shall I run next?: 1
OK: USBDEVFS_RESET succeeded
Which test shall I run next?: 0
After unbinding usbhid and restricting the mask:
$ sudo ./usbdevfs-drop-permissions /dev/bus/usb/001/002
...
Which option shall I run?: 3
Insert new mask: 0
OK: privileges dropped!
Which test shall I run next?: 2
ERROR claiming if 0 (1 - Operation not permitted)
ERROR claiming if 1 (1 - Operation not permitted)
ERROR claiming if 2 (1 - Operation not permitted)
ERROR claiming if 3 (1 - Operation not permitted)
Signed-off-by: Reilly Grant <reillyg@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is almost all under drivers/usb/dwc2/. Many
changes to the host side implementation of dwc2 have
been done by Douglas Anderson.
We also have USB 3.1 support added to the Gadget
Framework and, because of that work, dwc3 got
support to Synopsys new DWC_usb31 IP core.
Other than these 2 important series, we also have
the usual collection of non-critical fixes,
Documentation updates, and minor changes all over
the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vivP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb changes for v4.6 merge window
This is almost all under drivers/usb/dwc2/. Many
changes to the host side implementation of dwc2 have
been done by Douglas Anderson.
We also have USB 3.1 support added to the Gadget
Framework and, because of that work, dwc3 got
support to Synopsys new DWC_usb31 IP core.
Other than these 2 important series, we also have
the usual collection of non-critical fixes,
Documentation updates, and minor changes all over
the place.
Correct attribute name is port_num not num.
Fixes: ea6bd6b ("usb-gadget/f_acm: use per-attribute show and store methods")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
LPC32xx common clock framework driver correctly manages parent clocks
of USB device clock, so there is no need to manually enable and
disable them from the driver, which now depends only on a single USB
device clock.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Direct access to clock control registers can be safely removed, the
task of clock management is done by platform clock driver based on
common clock framework.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The driver requires to prepare/unprepare clocks to work properly on a
platform with enabled common clock framework, otherwise unprepared
clocks are not enabled:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:728 clk_core_enable+0x2c/0xf0()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc2+ #284
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xf0)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_udc_probe+0x284/0x924)
[<>] (lpc32xx_udc_probe) from [<>] (platform_drv_probe+0x50/0xa0)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x18c/0x408)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0x11c/0x248)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x50/0x64)
[<>] (__platform_driver_register) from [<>] (__platform_driver_probe+0x54/0x100)
[<>] (__platform_driver_probe) from [<>] (lpc32xx_udc_driver_init+0x1c/0x28)
[<>] (lpc32xx_udc_driver_init) from [<>] (do_one_initcall+0x11c/0x1dc)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A udc driver should set the giveback status to -ESHUTDOWN in
usb_ep_disable(). Otherwise, a gadget driver (e.g. g_serial) might
request next data wrongly and it is possible to cause kernel panic.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fixes a static analysis issue in dwc2_complete_non_isoc_xfer_ddma(). The
qtd was being passed to a function after being freed. It was not being
used in the function so this doesn't fix any bugs. But it fixes up the
warning and makes the code safer by setting qtd to NULL and not using it
at all.
Reported-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add support for Lantiq ARX and XRX SoC families to the dwc2 driver.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is possible for the VBUS detect GPIO interrupt to occur before
nop_set_peripheral() is called, in which case otg->gadget is NULL.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
bdc_ep_disable() expects to be called with bdc->lock held.
The assumption is met in all the cases except for call from bdc_udc_exit(),
that is called from bdc_remove(). As a result a race can happen or unheld
bdc->lock can be unlocked in bdc_req_complete().
The patch proposes to acquire-release bdc->lock around bdc_ep_disable()
in bdc_udc_exit().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The musb_hdrc_platform_data::config was defined as a non-const pointer.
However some drivers (e.g. the ux500) set up this pointer to point to a
static structure, which is potentially dangerous. Since the musb core
uses the pointer in a read-only manner the const qualifier was added to
protect the content of the config.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Move host core initialization and host channel routines into hcd.c. This
allows these functions to only be compiled in host-enabled driver
configurations (DRD or host-only).
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Move the register save and restore functions into the host and gadget
specific files.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Here, free memory is allocated using kmem_cache_zalloc. So, use
kmem_cache_free instead of kfree.
This is done using Coccinelle and semantic patch used
is as follows:
//<smpl>
@@
expression x,E,c;
@@
x =
\(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
... when != x = E
when != &x
?-kfree(x)
+kmem_cache_free(c,x)
//</smpl>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The microframe scheduler figured out exactly how many transfers we need
for a split transaction. Let's use this knowledge to know when to end
things.
Without this I found that certain devices would just keep responding
with tons of NYET resonses on their INT_IN endpoint. These would just
keep going and going and eventually we'd decide to terminate the
transfer (because the whole frame changed), but by that time the
scheduler would decide that we "missed" the start of the next transfer.
I can also imagine that if we blow past the end of our scheduled time we
may mess up other things that were scheduled to happen.
No known test cases are improved by this patch except that the scheduler
code doesn't yell about MISSES constantly anymore.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This totally reimplements the microframe scheduler in dwc2 to attempt to
handle periodic splits properly. The old code didn't even try, so this
was a significant effort since periodic splits are one of the most
complicated things in USB.
I've attempted to keep the old "don't use the microframe" schduler
around for now, but not sure it's needed. It has also only been lightly
tested.
I think it's pretty certain that this scheduler isn't perfect and might
have some bugs, but it seems much better than what was there before.
With this change my stressful USB test (USB webcam + USB audio + some
keyboards) crackles less.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When setting up ISO and INT transfers dwc2 needs to specify whether the
transfer is for an even or an odd frame (or microframe if the controller
is running in high speed mode).
The controller appears to use this as a simple way to figure out if a
transfer should happen right away (in the current microframe) or should
happen at the start of the next microframe. Said another way:
- If you set "odd" and the current frame number is odd it appears that
the controller will try to transfer right away. Same thing if you set
"even" and the current frame number is even.
- If the oddness you set and the oddness of the frame number are
_different_, the transfer will be delayed until the frame number
changes.
As I understand it, the above technique allows you to plan ahead of time
where possible by always working on the next frame. ...but it still
allows you to properly respond immediately to things that happened in
the previous frame.
The old dwc2_hc_set_even_odd_frame() didn't really handle this concept.
It always looked at the frame number and setup the transfer to happen in
the next frame. In some cases that meant that certain transactions
would be transferred in the wrong frame.
We'll try our best to set the even / odd to do the transfer in the
scheduled frame. If that fails then we'll do an ugly "schedule ASAP".
We'll also modify the scheduler code to handle this and not try to
schedule a second transfer for the same frame.
Note that this change relies on the work to redo the microframe
scheduler. It can work atop ("usb: dwc2: host: Manage frame nums better
in scheduler") but it works even better after ("usb: dwc2: host: Totally
redo the microframe scheduler").
With this change my stressful USB test (USB webcam + USB audio +
keyboards) has less audio crackling than before.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As we start getting more exact about our scheduling it's becoming more
and more important to know exactly how far through the current frame we
are. This lets us make decisions about whether there's still time left
to start a new transaction in the current frame.
We'll add dwc2_hcd_get_future_frame_number() which will tell you what
the frame number will be a certain number of microseconds (us) from
now. We can use this information to help decide if there's enough time
left in the frame for a transaction that will take a certain duration.
This is expected to be used by a future change ("usb: dwc2: host:
Properly set even/odd frame").
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc2 scheduler (contained in hcd_queue.c) was a bit confusing in the
way it initted / kept track of which frames a QH was going to be active
in. Let's clean things up a little bit in preparation for a rewrite of
the microframe scheduler.
Specifically:
* Old code would pick a frame number in dwc2_qh_init() and would try to
pick it "in a slightly future (micro)frame". As far as I can tell the
reason for this was that there was a delay between dwc2_qh_init() and
when we actually wanted to dwc2_hcd_qh_add(). ...but apparently this
attempt to be slightly in the future wasn't enough because
dwc2_hcd_qh_add() then had code to reset things if the frame _wasn't_
in the future. There's no reason not to just pick the frame later.
For non-periodic QH we now pick the frame in dwc2_hcd_qh_add(). For
periodic QH we pick the frame at dwc2_schedule_periodic() time.
* The old "dwc2_qh_init() actually assigned to "hsotg->frame_number".
This doesn't seem like a great idea since that variable is supposed to
be used to keep track of which SOF the interrupt handler has seen.
Let's be clean: anyone who wants the current frame number (instead of
the one as of the last interrupt) should ask for it.
* The old code wasn't terribly consistent about trying to use the frame
that the microframe scheduler assigned to it. In
dwc2_sched_periodic_split() when it was scheduling the first frame it
always "ORed" in 0x7 (!). Since the frame goes on the wire 1 uFrame
after next_active_frame it meant that the SSPLIT would always try for
uFrame 0 and the transaction would happen on the low speed bus during
uFrame 1. This is irregardless of what the microframe scheduler
said.
* The old code assumed it would get called to schedule the next in a
periodic split very quickly. That is if next_active_frame was
0 (transfer on wire in uFrame 1) it assumed it was getting called to
schedule the next uFrame during uFrame 1 too (so it could queue
something up for uFrame 2). It should be possible to actually queue
something up for uFrame 2 while in uFrame 2 (AKA queue up ASAP). To
do this, code needs to look at the previously scheduled frame when
deciding when to next be active, not look at the current frame number.
* If there was no microframe scheduler, the old code would check for
whether we should be active using "qh->next_active_frame ==
frame_number". This seemed like a race waiting to happen. ...plus
there's no way that you wouldn't want to schedule if next_active_frame
was actually less than frame number.
Note that this change doesn't make 100% sense on its own since it's
expecting some sanity in the frame numbers assigned by the microframe
scheduler and (as per the future patch which rewries it) I think that
the current microframe scheduler is quite insane. However, it seems
like splitting this up from the microframe scheduler patch makes things
into smaller chunks and hopefully adds to clarity rather than reduces
it. The two patches could certainly be squashed. Not that in the very
least, I don't see any obvious bad behavior introduced with just this
patch.
I've attempted to keep the config parameter to disable the microframe
scheduler in tact in this change, though I'm not sure it's worth it.
Obviously the code is touched a lot so it's possible I regressed
something when the microframe scheduler is disabled, though I did some
basic testing and it seemed to work OK. I'm still not 100% sure why you
wouldn't want the microframe scheduler (presuming it works), so maybe a
future patch (or a future version of this patch?) could remove that
parameter.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We'll use the new "scheduler verbose debugging" macro to log missed
SOFs. This is fast enough (assuming you configure it to use the ftrace
buffer) that we can do it without worrying about the speed hit. The
overhead hit if the scheduler tracing is set to "no_printk" should be
near zero.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This no-op change splits code out of dwc2_schedule_periodic() into a
dwc2_do_reserve() function. This makes it a little easier to follow the
logic.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This no-op change just reorders a few functions in hcd_queue.c in order
to prepare for future changes. Motivations here:
The functions dwc2_hcd_qh_free() and dwc2_hcd_qh_create() are exported
functions. They are not called within the file. That means that they
should be near the bottom so that they can easily call static helpers.
The function dwc2_qh_init() is only called by dwc2_hcd_qh_create() and
should move near the bottom with it.
The only reason that the dwc2_unreserve_timer_fn() timer function (and
its subroutine dwc2_do_unreserve()) were so high in the file was that
they needed to be above dwc2_qh_init(). Now that dwc2_qh_init() has
been moved down it can be moved down a bit. A later patch will split
the reserve code out of dwc2_schedule_periodic() and the reserve
function should be near the unreserve function. The reserve function
needs to be below dwc2_find_uframe() since it calls that.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This no-op change just does some renames to simplify a future patch.
1. The "interval" field is renamed to "host_interval" to make it more
obvious that this interval may be 8 times the interval that the
device sees (if we're doing split transactions). A future patch will
also add the "device_interval" field.
2. The "usecs" field is renamed to "host_us" again to make it more
obvious that this is the time for the transaction as seen by the
host. For split transactions the device may see a much longer
transaction time. A future patch will also add "device_us".
3. The "sched_frame" field is renamed to "next_active_frame". The name
"sched_frame" kept confusing me because it felt like something more
permament (the QH's reservation or something). The name
"next_active_frame" makes it more obvious that this field is
constantly changing.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The old code in dwc2_process_periodic_channels() would only enable the
"periodic empty" interrupt if we weren't using DMA. That wasn't right
since we can still get into cases where we have small FIFOs even on
systems that have DMA (the rk3288 is a prime example).
Let's always enable/disable the "periodic empty" when appropriate. As
part of this:
* Always call dwc2_process_periodic_channels() even if there's nothing
in periodic_sched_assigned (we move the queue empty check so we still
avoid the extra work). That will make extra certain that we will
properly disable the "periodic empty" interrupt even if there's
nothing queued up.
* Move the enable of "periodic empty" due to non-empty
periodic_sched_assigned to be for slave mode (non-DMA mode) only.
Presumably this was the original intention of the check for DMA since
it seems to match the comments above where in slave mode we leave
things on the assigned queue.
Note that even before this change slave mode didn't work for me, so I
can't say for sure that my understanding of slave mode is correct.
However, this shouldn't change anything for slave mode so if slave mode
worked for someone in the past it ought to still work.
With this change, I no longer get constant misses reported by my other
debugging code (and with future patches) when I've got:
* Rockchip rk3288 Chromebook, using port ff540000
-> Pluggable 7-port Hub with Charging (powered)
-> Microsoft Wireless Keyboard 2000 in port 1.
-> Das Keyboard in port 2.
-> Jabra Speaker in port 3
-> Logitech, Inc. Webcam C600 in port 4
-> Microsoft Sidewinder X6 Keyboard in port 5
...and I'm playing music on the USB speaker and capturing video from the
webcam.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
I find that when I plug a full speed (NOT high speed) hub into a dwc2
port and then I plug a bunch of devices into that full speed hub that
dwc2 goes bat guano crazy. Specifically, it just spews errors like this
in the console:
usb usb1: clear tt 1 (9043) error -22
The specific test case I used looks like this:
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
|__ Port 1: Dev 17, If 0, Class=Hub, Driver=hub/4p, 12M
|__ Port 2: Dev 19, If 0, ..., Driver=usbhid, 1.5M
|__ Port 4: Dev 20, If 0, ..., Driver=usbhid, 12M
|__ Port 4: Dev 20, If 1, ..., Driver=usbhid, 12M
|__ Port 4: Dev 20, If 2, ..., Driver=usbhid, 12M
Showing VID/PID:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 017: ID 03eb:3301 Atmel Corp. at43301 4-Port Hub
Bus 001 Device 020: ID 045e:0745 Microsoft Corp. Nano Transceiver ...
Bus 001 Device 019: ID 046d:c404 Logitech, Inc. TrackMan Wheel
I spent a bunch of time trying to figure out why there are errors to
begin with. I believe that the issue may be a hardware issue where the
transceiver sometimes accidentally sends a PREAMBLE packet if you send a
packet to a full speed device right after one to a low speed device.
Luckily the USB driver retries and the second time things work OK.
In any case, things kinda seem work despite the errors, except for the
"clear tt" spew mucking up my console. Chalk it up for a win for
retries and robust protocols.
So getting back to the "clear tt" problem, it appears that we get those
because there's not actually a TT here to clear. It's my understanding
that when dwc2 operates in low speed or full speed mode that there's no
real TT out there. That makes all these attempts to "clear the TT"
somewhat meaningless and also causes the spew in the log.
Let's just skip all the useless TT clears. Eventually we should root
cause the errors, but even if we do this is still a proper fix and is
likely to avoid the "clear tt" error in the future.
Note that hooking up a Full Speed USB Audio Device (Jabra 510) to this
same hub with the keyboard / trackball shows that even audio works over
this janky connection. As a point to note, this particular change (skip
bogus TT clears) compared to just commenting out the dev_err() in
hub_tt_work() actually produces better audio.
Note: don't ask me where I got a full speed USB hub or whether the
massive amount of dust that accumulated on it while it was in my junk
box affected its funtionality. Just smile and nod.
Acked-by: John Youn <johnyoun@synopsys.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
In case you didn't spot it, the difference is the "- 1".
Let's add the "- 1" to match the newest user manual. It's presumed that
the "- 1" should have always been there and that this was always a
documentation error. If some hardware needs the "- 1" and other
hardware doesn't, we'll have to add a configuration parameter for it in
the future.
I checked things before and after this patch on rk3288 using a Total
Phase Beagle 5000 analyzer.
Before this patch, a low speed mouse shows constant Frame Timing Jitter
errors. After this patch errors have gone away.
Before this patch SOF packets move forward about 1 us per 4 ms. After
this patch the SOF packets move backward about 1 us per 255 ms. Some
specific SOF timestamps from the analyzer are below.
Before:
6.603.790
6.603.916
6.604.041
6.604.166
...
6.607.541
6.607.667
6.607.792
6.607.917
...
6.611.417
6.611.543
6.611.668
6.611.793
After:
6.215.159
6.215.284
6.215.408
6.215.533
6.215.658
...
6.470.658
6.470.783
6.470.907
...
6.726.032
6.726.157
6.725.281
6.725.406
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In commit 94dfd7edfd ("USB: HCD: support giveback of URB in tasklet
context") support was added to give back the URB in tasklet context.
Let's take advantage of this in dwc2.
This speeds up the dwc2 interrupt handler considerably.
Note that this requires the change ("usb: dwc2: host: Add a delay before
releasing periodic bandwidth") to come first.
Note that, as per Alan Stern in
<https://patchwork.kernel.org/patch/7555771/>, we also need to make sure
that the extra delay before the device drivers submit more data doesn't
break the scheduler. At the moment the scheduler is pretty broken (see
future patches) so it's hard to be 100% certain, but I have yet to see
any new breakage introduced by this delay. ...and speeding up interrupt
processing for dwc2 is a huge deal because it means we've got a better
chance of not missing SOF interrupts. That means we've got an overall
win here.
Note that when playing USB audio and using a USB webcam and having
several USB keyboards plugged in, the crackling on the USB audio device
is noticably reduced with this patch.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We'd like to be able to use HCD_BH in order to speed up the dwc2 host
interrupt handler quite a bit. However, according to the kernel doc for
usb_submit_urb() (specifically the part about "Reserved Bandwidth
Transfers"), we need to keep a reservation active as long as a device
driver keeps submitting. That was easy to do when we gave back the URB
in the interrupt context: we just looked at when our queue was empty and
released the reserved bandwidth then. ...but now we need a little more
complexity.
We'll follow EHCI's lead in commit 9118f9eb4f ("USB: EHCI: improve
interrupt qh unlink") and add a 5ms delay. Since we don't have a whole
timer infrastructure in dwc2, we'll just add a timer per QH. The
overhead for this is very small.
Note that the dwc2 scheduler is pretty broken (see future patches to fix
it). This patch attempts to replicate all old behavior and just add the
proper delay.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In preparation for future changes to the scheduler let's add some
tracing that makes it easy for us to see what's happening. By default
this tracing will be off.
By changing "core.h" you can easily trace to ftrace, the console, or
nowhere.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We're supposed to keep outstanding splits in order. Keep track of a
list of the order of splits and process channel interrupts in that
order.
Without this change and the following setup:
* Rockchip rk3288 Chromebook, using port ff540000
-> Pluggable 7-port Hub with Charging (powered)
-> Microsoft Wireless Keyboard 2000 in port 1.
-> Das Keyboard in port 2.
...I find that I get dropped keys on the Microsoft keyboard (I'm sure
there are other combinations that fail, but this documents my test).
Specifically I've been typing "hahahahahahaha" on the keyboard and often
see keys dropped or repeated.
After this change the above setup works properly. This patch is based
on a previous patch proposed by Yunzhi Li ("usb: dwc2: hcd: fix periodic
transfer schedule sequence")
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The queues the the dwc2 host controller used are truly queues. That
means FIFO or first in first out.
Unfortunately though the code was iterating through these queues
starting from the head, some places in the code was adding things to the
queue by adding at the head instead of the tail. That means last in
first out. Doh.
Go through and just always add to the tail.
Doing this makes things much happier when I've got:
* 7-port USB 2.0 Single-TT hub
* - Microsoft 2.4 GHz Transceiver v7.0 dongle
* - Jabra speakerphone playing music
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When poking around with USB devices with slub_debug enabled, I found
another obvious use after free. Turns out that in dwc2_hc_n_intr() I
was in a state when the contents of chan->qh was filled with 0x6b,
indicating that chan->qh was freed but chan still had a reference to
it.
Let's make sure that whenever we free qh we also make sure we remove a
reference from its channel.
The bug fixed here doesn't appear to be new--I believe I just got lucky
and happened to see it while stress testing.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As documented in dwc2_calculate_dynamic_fifo(), host_rx_fifo_size should
really be:
2 * ((Largest Packet size / 4) + 1 + 1) + n
with n = number of host channel.
We have 9 host channels, so
2 * ((1024/4) + 2) + 9 = 516 + 9 = 525
We've got 960 / 972 total_fifo_size on rk3288 (and presumably on
rk3066) and 525 + 128 + 256 = 909 so we're still under on both ports
even when we increment by 5.
In the future, it would be nice if dwc2_calculate_dynamic_fifo() could
handle the "too small" FIFO case and come up with something more
dynamically. When we do that we can figure out how to allocate the
extra 48 / 60 bytes of FIFO that we're currently wasting.
NOTE: no known bugs are fixed by this patch, but it seems like a simple
fix and ought to fix someone.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
All other host controllers who want aligned buffers for DMA do it a
certain way. Let's do that too instead of working behind the USB core's
back. This makes our interrupt handler not take forever and also rips
out a lot of code, simplifying things a bunch.
This also has the side effect of removing the 65535 max transfer size
limit.
NOTE: The actual code to allocate the aligned buffers is ripped almost
completely from the tegra EHCI driver. At some point in the future we
may want to add this functionality to the USB core to share more code
everywhere.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: John Youn <johnyoun@synopsys.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Previously we needed to set the max_transfer_size to explicitly be 65535
because the old driver would detect that our hardware could support much
bigger transfers and then would try to do them. This wouldn't work
since the DMA alignment code couldn't support it.
Later in commit e8f8c14d9d ("usb: dwc2: clip max_transfer_size to
65535") upstream added support for clipping this automatically. Since
that commit it has been OK to just use "-1" (default), but nobody
bothered to change it.
Let's change it to default now for two reasons:
- It's nice to use autodetected params.
- If we can remove the 65535 limit, we can transfer more!
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Check that dwc->maximum_speed is set to a valid value. Also add an error
when we use it later if we encounter an invalid value.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Felipe Balbi