SRC_ROUTE_MODE0 determines whether to use SRC.
Thus, it should be setup before SRC_SRCIR.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels number is not only for DVC. Let's rename it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
b4c83b171 ("ASoC: rsnd: add Multi channel support") added
Multi channel support, and current rsnd_ssi_is_multi_slave()'s check
method is !SSI equals SSIM1/2/3. But, SSI parent also hit to this macro.
Because of this reason, some stream which needs SSI parent clock
can't work correctly. This patch uses rsnd_ssi_multi_slaves() to
solve this issue. This issue was reported by Dung.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has .init/.start/.stop/.quit callbacks,
and it needs many IPs (SRC/CTU/MUX/DVC/CMD/SSIU/SSI).
Because of these relationship, it might get unnecessary
error IRQ when start/stop.
This patch adds new .irq callback and control IRQ enable/disable
timing to avoid it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound needs recovery (= restart) when under/over run
error occurred, and current driver tries it on under/over run error
handler automatically. But this recovery should be handled by userland,
not kernel. This patch stops XRUN when under/over run error occur, and
will leave the recovery of HW in userland.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b761bf272b ("ASoC: rsnd: disable SRC.out only when stop timing")
disabled SRC.out/in in different timing, but was based on
picky HW information. Now, we have confirmed that we can disable
both in the same time. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current CTU settings was rough. This patch makes it match to datasheet.
But do nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI/SRC will try to attach DMAC as Audio-DMAC or Audio-DMAC-periperi.
It is fixed IP, but will be attached to each streams as different module
in case of MUX (= multi sound path will be merged).
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will be used as normal SSI or as clock parent SSI. Therefor,
rsnd driver wants to control SSI and parent SSI separately. Otherwise it
can't use Playback/Capture in the same time.
And it has been done by c2dc47d5cf("ASoC: rsnd: rsnd_dai_stream has each
mod's status insted of rsnd_mod") before.
OTOH, rsnd driver doesn't want to control CTU/MUX/DVC/SSIU/SSI in
separately. Otherwise, these will be re-initialized during playing if
MUX merges 2 sounds.
Because of these picky reasons, this patch re-defines status on each mod,
and add new parent_ssi_status on rsnd_dai_stream.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To select CMD data patch, it should use correct SRC from each stream
in MUX case. But current code is selecting SRC from fixed stream.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_cmd_init() overwrites "io" which will be used end of this
function. This patch solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CTU/MUX/DVC/SSIU/SSI/Audio-DMAC-periperi might be used under multipath.
So, probe()/remove() need to be called multiple times.
This patch allows it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system uses CTU/MUX, CTU/MUX/DVC will try to connect same CMD to
system, but it is not error in this case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system uses CTU/MUX, and if probe error happened, it will try to
call rsnd_dai_call(remove, ...). Then, MUX/DVC/SSIU/SSI might be called
without calling rsnd_dai_call(probe, ...). Then, each mod status might
be un-matched. It doesn't call un-matched remove function by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_call() tries to call each IP's relevant function. But it is
difficult to understand which function returned error.
This patch adds debug message for this purpose
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ADG doesn't use rsnd_mod_init(), but this limitation is no
longer necessary. Let's use common rsnd_mod_init()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bitwise OR has higher precedence than ?: so the val2 was always set
to 0x2.
Fixes: b4c83b1715 ('ASoC: rsnd: add Multi channel support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Field usrcnt is unsigned so it cannot be lesser than zero.
The patch fixes the check, moves it to the beginning of the function
and changes return value to -EIO in case of usercnt error.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Multi channel support on Renesas R-Car sound.
This patch is tested on Salvator-X board, but it can't use
Multi channel, because supported format is different between
codec chip and R-Car.
Thus, it was tested on board which doesn't mount codec chip,
with oscilloscope.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using complex macro to parse DAI connection.
This patch adds new rsnd_parse_connect_common() and replace current
macro to it.
This is prepare for multi channel support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM will use 6 or 8 slots on 1 SSI, and Multi channel will use
6 or 8 slots on few SSI (each SSI uses 2 slots).
Thus, this adds new slot control functions which can be prepare
for Multi channel support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_get_slot_rdai() returns total slots (it returns 6 if total 6
channels) , and rsnd_get_slot_extend() returns extended SSI width
(it returns 8 if total 6 channels). This will be used on SSI multi
channel support too (It will return 2 if total 6 channels with 3 SSI).
But, it is using confusable naming.
This patch changes rsnd_get_slot_rdai() -> rsnd_get_slot(),
rsnd_get_slot_extend() -> rsnd_get_slot_width()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver is using rsnd_get_slot_runtime(), but
it is same as runtime->channels. This patch removes
rsnd_get_slot_runtime()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI/SSIU are using rsnd_get_slot_runtime() to check TDM,
but using rsnd_get_slot_extend() is more sane.
This patch fix it up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can't output corrent dma name *before* rsnd_mod_init().
It goes to *after* rsnd_mod_init() by this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver has rsnd_get_adinr_bit/chan() functions.
It is assuming _bit() returns ADINR :: OTBL,
and _chan() returns ADINR :: CHNUM.
Current _bit() returns both OTBL and CHNUM. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSIU should be controlled after SSI. This patch fix up it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsrc-card is DPCM supported version of simple-card. Thus it has similar
DT format. OTOH, snd_soc_dai_link requests cpu/codec, but one of them
will be snd-soc-dummy in DPCM case, and DPCM requests frontend/backend
dai_link. This means it might have multi backend/codec.
And, SND_SOC_DAIFMT_xxx is based on "codec". Because of these
difference, current rsrc card can't detect correct dai_fmt.
This patch detect correct dai fmt from 1st "codec".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
1efb53a220 ("ASoC: simple-card: Remove support for setting differing
DAI formats") removed set_fmt support from simple-card.
rsrc-card follows same style, because it is based on simple-card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver will use tdm slot on TDM Multi Mode support.
This patch enables tdm slot on rsrc card driver on DT.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_mix_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_dvc_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ret as the return value from the rsnd_ctu_probe() but if there
are no child nodes and no errors then we will never initialize ret leading
to build warnings. Ensure ret is initialized before we iterate over the
child nodes to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
L/R channel data has been treated as inverted on R-Car sound 16bit mode,
Thus, 4689032b1("ASoC: rsnd: tidyup data align position") tidyuped data
align position. But it couldn't care about capture case. This patch
cares both playback/capture
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSICR::SWSP bit controls WS signal low/high, but in case of TDM
it is inverted. This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing check of snd_soc_of_get_dai_name().
It might not be able to use sound card, because it might returns
-EPROBE_DEFER.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drv pointer should be "base + offset" instead of
"current + offset". This patch fixup this issue, otherwise
third and subsequent pointer will be broken
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car can out TDM by
1) 6ch x 1 DAI as TDM Extend Mode
2) 2ch x 4 x 1 DAI as TDM split Mode
3) 2ch x 3 DAI or
2ch x 4 DAI as TDM Multichannel Mode
This patch adds 1) TDM Extend Mode. Because of HW design,
this 6ch data will be outputed via 8ch data width.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DVC is assuming that the sound is always stereo.
This patch makes it more flexible
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI is assuming that the sound is always stereo. But, SSI needs
to calculate its frequency when master mode. Then This frequency depends
on each SSI's slots, and TDM mode (= TDM Extend Mode, TDM split Mode,
TDM Multichannel Mode).
This patch enables to use non-stereo sound.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will have TDM settings on SSIWSR. Actually, we would like to set
it on rsnd_ssi_config_init(), but we can't. Because SSI might be used
as clock master (It doesn't need to call rsnd_ssi_config_init() when
clock master mode).
This patch adds new ssi->wsr and set it on rsnd_ssi_start().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to enhance code readability, this patch adds
rsnd_ssi_config_init() and moves SSICR register settings to it.
This is prepare patch for TDM support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC_BUSIF_MODE has both IN/OUT register. Current src driver sets
IN register only. This patch sets missing OUT register.
IN/OUT register are using default setting, so, there is no
HW effect.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC/SRC/SSIU needs ADINR::CHNUM settings too. This patch adds
these missing value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
adg.c is used from ssi/src/cmd. Thus don't use confusable *mod here.
This patch rename it to ssi_mod/src_mod/cmd_mod
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi_record_error() should recorde error, but it clears error too.
this patch fixes up semantic of rsnd_ssi_record_error that it records
error but doesn't clear error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_src_error_record() should recorde error, but it clears error too.
this patch fixes up semantic of rsnd_src_error_record that it records
error but doesn't clear error.
And this patch renames
rsnd_src_error_clear() to rsnd_src_status_clear()
rsnd_src_error_record() to rsnd_src_record_error()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is indicating how to use regmap debug method
on gen.c comment area.
regmap debug method indicates address and value, but rsnd driver is
using too many IPs (SSI/SSIU/SRC/CTU/MIX/DVC/CMD), and address.
Thus, we would like to know more useful information for debugging.
This patch indicates address name for debugging.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After a recent cleanup, the soc_card variable became unused
and now produces a warning:
soc/sh/rcar/core.c: In function '__rsnd_kctrl_new':
soc/sh/rcar/core.c:801:23: warning: unused variable 'soc_card' [-Wunused-variable]
This removes the variable.
Fixes: 1a497983a5 ("ASoC: Change the PCM runtime array to a list")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
64bit compiler indicates this without this patch
linux/sound/soc/sh/rcar/core.c: In function 'rsnd_probe':
linux/sound/soc/sh/rcar/core.c:1002:16: warning: cast from pointer to\
integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the number of DAI links is statically defined by the machine
driver at build time using an array. This makes it difficult to shrink/
grow the number of DAI links at runtime in order to reflect any changes
in topology.
We can change the DAI link array in the core to a list so that PCMs and
FE DAI links can be added and deleted at runtime to reflect changes in
use case and DSP topology. The machine driver can still register DAI links
as an array.
As the 1st step, this patch change the PCM runtime array to a list. A new
PCM runtime is added to the list when a DAI link is bound successfully.
Later patches will further implement the DAI link list.
More:
- define snd_soc_new/free_pcm_runtime() to create/free a runtime.
- define soc_add_pcm_runtime() to add a runtime to the rtd list.
- define soc_remove_pcm_runtimes() to clean up the runtime list.
- traverse the rtd list to probe the link components and dais.
- Add a field "num" to PCM runtime struct, used to specify the device
number when creating the pcm device, and for a soc card to access
its dai_props array.
- The following 3rd party machine/platform drivers iterate the rtd list
to check the runtimes:
sound/soc/intel/atom/sst-mfld-platform-pcm.c
sound/soc/intel/boards/cht_bsw_rt5645.c
sound/soc/intel/boards/cht_bsw_rt5672.c
sound/soc/intel/boards/cht_bsw_max98090_ti.c
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver requests struct platform_device on
probe/remove for each modules. But driver can get it by
rsnd_priv_to_pdev(). This patch removes unnecessary parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
Now, platform boot style was removed from driver.
This is cleanup patch, and remove pointless struct rcar_snd_info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
Now, platform boot style was removed from driver.
This is cleanup patch, and remove pointless struct rsnd_of_data
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from gen.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from dvc.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from mix.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from ctu.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from src.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from ssi.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No board is using Renesas sound driver via platform boot now.
This means all user is using DT boot. Platform boot support is
no longer needed. But, it strongly depends on platform boot style.
This patch removes platform boot support from core.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC settings order was rough. Now, Gen1 support was removed.
This patch makes it cleanup and match to datasheet.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC Gen1 support was removed. Current rsnd driver is sharing Gen1/Gen2
register index to reduce memory, but there is no effect anymore.
Let's remove share definition and merge RSND_REG_xxx
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes SRC Gen1 support which has no user on upstream.
Historically, SRC Gen1 was created as prepare for SRC Gen2 support.
It works well for Gen2 support, but Gen1 is not same as Gen2.
So now, Gen1 support is no longer needed. Thanks Gen1 and Bye-bye.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Data left/right aligned is controlled by PDTA bit on SSICR.
But default is left-aligned. Thus 24bit sound will be very small sound
without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG can output AUDIO_CLKOUTx, and these are generated from
AUDIO_CLKx. Thus we need to call clk_prepare()/clk_enable()
for AUDIO_CLKx.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
f1df12290("ASoC: rsnd: add common mod confirm method")
added rsnd_mod_make_sure(), but rsnd_mod_xxx() comment position
was wrong. This patch tidyup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current MIX settings order was rough.
This patch makes it match to datasheet.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DVC settings order was rough.
This patch makes it match to datasheet.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
8cca6e11c1 ("ASoC: rsnd: use mod base common method on CMD")
added cmd.c. Let's move CMD related operation to cmd.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the "clock-frequency" DT property is not found, req_rate is used
uninitialized, and the "audio_clkout" clock will be created with an
arbitrary clock rate.
This uninitialized kernel stack data may leak to userspace through
/sys/kernel/debug/clk/clk_summary, cfr. the value in the "rate" column:
clock enable_cnt prepare_cnt rate accuracy phase
--------------------------------------------------------------------
audio_clkout 0 0 4001836240 0 0
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
45a4394d03("ASoC: rsnd: use mod base common method on DMA phase3")
Exchanged "void rsnd_dmapp_stop()" to "int rsnd_dmapp_stop()",
but it returns inverted value. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
2d604e03("ASoC: rsnd: disable SRC.out only when stop timing")
added rsnd_src_quit_gen2(), but it should call rsnd_src_quit()
same as before. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
This patch makes SSI parent mod base common method
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
This patch makes SSIU mod base common method
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
This patch makes CMD mod base common method
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
This patch makes DMA mod bse common method
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
DMA will be implemented as module. Then rsnd_dma_ops will be rebased
to rsnd_mod_ops, but these are similar, but different function.
This patch modify rsnd_dma_ops same style as rsnd_mod_ops.
This is prepare for final merge
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
DMA will be implemented as module. Then rsnd_dma will be mod base.
This patch makes rsnd_dma mod base, but still not yet completely
finished. This mod is not yet installed to system at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ssi.c driver has random access to SSISR register. Let's use
common rsnd_ssi_status_xxx() function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound driver doesn't have 1:1 relationship between
stream <-> mod because it is supporting MIX. Because of this reason
rsnd_mod_interrupt() is searching correspond mod by for loop.
But this loop is not needed, because each mod has own type.
This patch avoid pointless loop by using mod->type.
This patch is good for SSI-parent support, because stream might have
2 SSI as SSI-parent/child. SSI interrupt handler will be called twice
if stream has SSI-parent without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI/SRC restarts HW if under/over flow happened to avoid L/R
invert issue. But it will stop HW if too many error happen.
But if it stops on HW, other side under/over flow happen. OTHA, it will
be forever loop interrupt if something strange error happen on
HW/driver without escape route of large number error.
To avoid this issue, it indicates error message if large number error
occur, and disables error interrupt.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
Current rsnd is controling each mod's status on mod. But it was not
good design for SSI, because stream might has SSI-parent.
In such case, it can't play/capture in same time, because SSI-parent
is used as normal SSI in other stream, but it shares same status.
To avoid this issue each mod's status is controlled by rsnd_dai_stream
instead of rsnd_mod.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because SRC is connected to DMA and DMA want to keep dreq when stop
timing. This patch makes SRC stop SRC.out only when stop timing. And
it stops both SRC.out/SRC.in when quit timing
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Part of SSI IRQ enable/disable was controlled by SRU (on Gen1)
or CMD (on Gen2). Because of this reason SSI IRQ function was
implemented under src.c. but it is not understandable.
Let's move it to ssi.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
Current rsnd_dma_of_path is assuming that all mods are related to DMA.
But it will be wrong. This patch tidyup this wrong assumption
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas sound is supporting PIO fallback if it can't use DMA.
In such case, it should remove all attached modules, but current driver
is missing about CTU/MIX. Because current implement requests
specific mod for remove.
To avoid same things in future, this patch removes all mods,
and re-connects SSI when PIO fallback case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
DMAC/SSIU/SSI-parent/CMD will be implemented as module, but these are
not customer controlled module. These should be automatically install
to system. Because of this, rsnd_dai_connect() should be called from
each mod. SSI can be very special, because it will be installed as
SSI-parent / SSI-child. Thus, new rsnd_dai_connect() has type parameter
which should be mod->type except SSI-parent
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
DMA will be implemented as module. Then each rsnd_dma_ops will be
rsnd_mod_ops. But current rsnd_dma_ops::init means "DMA attach".
This patch removes .init from rsnd_dma_ops, and renames
rsnd_dma_init() to rsnd_dma_attach()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
DMA will be implemented as module. Current DMA definition is no longer
needed on rsnd.h. Let's move it to dma.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound needs many devices
(SSI/SSIU/SRC/CTU/MIX/DVC/CMD/AudioDMAC/AudioDMACpp).
SSI/SRC/CTU/MIX/DVC are implemented as module.
SSI parent, SSIU are implemented as part of SSI
CMD is implemented as part of CTU/MIX/DVC
AudioDMAC/AudioDMACpp are implemented as part of SSI/SRC
It is nice sense that these all devices are implemented as mod.
Current rsnd_mod is member of rsnd_mod. But the DMA user is only
SSI/SRC. This DMA will be implemented as module. As 1st step, DMA
become SSI/SRC member by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC In Rate convert feature cannot be used if data path is using DVC.
This patch judges it, and not allowed to use it in such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWLbbGAAoJECTWi3JdVIfQH7oH/1VdN2ozP9A03p24aC5qso1F
VWOBnG4pkw1G6J5qK2lemMDeJdRdTfreICUAa9Tw9kOSfTIb6F3X8kCw8tbwlw0I
4phgmyo23P53OfLZFMkQi/RCfwItnE0sszqhvoumUg0ryjYxg2JT+gTMgwvVo7Pq
hf6m6a3we5pxLIIYP4wlQgOKwUJe4B4nC37ExySf24Dlo/DzmWDtfQbGvmyluFzb
MB1qzEvAc/KC3LZFkIFmhfg2/caNRhcQrzkUCYrLR3t+oz9P1zCpYTII7VDdMg7L
SM2VoL+ynEAdBqa38Ozwxvd/mpHwinlAeiikuwz1PyxVOqZvZqqiWzD8eUJkhZk=
=/F/Q
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc6' into asoc-fix-rcar
ASoC: Updates for v4.4
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
cfcefe0126 ("ASoC: rsnd: add recovery support for under/over flow
error on SRC") added SCU_SYS_INT_EN1 address, but it should be
0x1d4, not 0x1c4. This patch fixup it.
Fixes: cfcefe0126 ("ASoC: rsnd: add recovery support for under/over flow error on SRC")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
rsnd_ssi_use_busif() and rsnd_ssi_is_pin_sharing() are the function
which returns current SSI status. But these requests duplicated parameter.
This patch removes duplicated parameter.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dma_to_ssi() is no longer used, let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_hw_start/stop were unclear naming.
It became rsnd_mod_power_on/off by this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dai_call returns immediately if rsnd_mod_call return fail.
Thus, each callback-count can be unbalanced for example .init was OK,
start was OK, but, .stop was not OK. This case .quit should be called
but isn't called. And, rsnd_dai_stream_quit() also not be called.
rsnd_dai_call() should call all .stop/.quit eventhough it returns error.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_dai_call didn't count callback-count if callback
wasn't implemented. Thus, it counts can be unbalance.
ex) .start : implemented
.stop : not implemented
This patch solve this issue
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Indicating each module method as debug message before executing is
readable/understandable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
bfc0cfe("ASoC: rsnd: don't use rsnd_mod_to_io() on rsnd_ssi_xxx()")
tidyuped devm_request_irq() option from ssi to mod, but devm_free_irq()
on rsnd_ssi_dma_remove() didn't modified. This patch fixups this issue.
Otherwise kernel will output WARNING message.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct rsnd_gen :: res array size should be RSND_BASE_MAX,
not RSND_REG_MAX. This patch fixup it, and indicates whether
each data array size is based on what
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
debug meesage for rsnd_mod_read() should be prints after read
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Probing from Gen1 is not error. This patch fixup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Gen1 SRU support was created for preparation of Gen2 SRC support,
but no-one is using this feature (sampling rate convert) on Gen1.
BockW had used SRU before, but it was pass through mode.
This means it is same as SSI. And BockW "platform base" code was
removed from upstream code. It is now supported via DT, but it doesn't
use SRU. More detail, r8a7778.dtsi has "rcar_sound,src" entry, but
no-one is using this feature today. SRU probing has no relation to this
removing. This means there is no effect for DT compatibility, no issues
on upstream kernel.
Gen2 SRC was created from Gen1 SRU, these are similar but not same IP.
Keeping Gen1 SRU in current driver is a little bit difficult,
and no-one is using it today. Gen1 sound is still supported via SSI.
Gen1 SRU support will be removed in the next kernel version.
This patch announces it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 3d7608e4c1 ("ARM: shmobile: bockw: remove legacy
board file and config"), Renesas R-Car SoCs are only supported in
generic DT-only ARM multi-platform builds. The driver doesn't need to
use platform data anymore, hence remove platform data configuration.
Move <sound/rcar_snd.h> to sound/soc/sh/rcar/, as it's no longer needed
by platform code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
2a46db4a3("ASoC: rsnd: add AUDIO_CLKOUT support") added AUDIO_CLKOUT
support for ADG. But single AUDIO_CLKOUT needs clkout_name[CLKOUT],
not clkout_name[i]. Kernel will have NULL pointer access without this
patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound has AUDIO_CLKOUT (in Gen1/Gen2) AUDIO_CLKOUT1/2/3 (in Gen3)
This patch support these patches as clock provider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
undefined clock is not error. Accept such case. And this is prepare
for clock out support in the same time.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It didn't have "\n", and indicated different data
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ADG clock calculation needs ADG and SSI settings.
Thus, SSI side clock request function depends on ADG settings.
After reconsideration, we can close this method inside ADG.
This function uses new method. And it becomes preparation for
AUDIO_CLKOUT support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG is special IP since it doesn't have MSTP. And now, ADG has common
mod base register access. We can now setup ADG initial setting when
probe timing. It is needed if sound card is based on AUIDO_CLK which
is used as Master clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound has SSI/SRC/DVC/MIX/ADG modules, and these have original
register mapping. Thus this driver is using regmap field, and each module
is using it based on each module ID.
Sometimes, each module needs other module to controlling. but current each
function is using just "mod" as parameter name. This is confusable.
For example, if SSI0 and SRC2 are connected, and if SRC module function
has bug of module access, and if it needs to control connected SSI,
SRC function will access to SSI2 (It should access to SSI0, but it uses
SRC's ID 2). This is easy to happen in current driver style.
To avoid this kind of confusable trouble, this patch adds module confirm
macro for debug purpose.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound has ADG IP, but it is special device.
(It is clock generater, and it doesn't need MSTP)
Thus, ADG didn't use mod base common method on rsnd driver.
But it can be confusable point. Let's use common method
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver has SSI/SRC/DVC/CTU/MIX, and these are controlled
as modules. And these module are member of each modules's private data.
It used own method to get module pointer, but Let's use common method
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound Gen3 is updated version of Gen2. We need to update
driver for it, but basically it should works as Gen2 compatible.
This is initial support for Gen3. Gen3 specific feature will be
incrementally added in the future
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sh_clk header is not needed, and it will create confusion.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_src_pcm_new() is used only from Gen2. make it clear in function name,
and remove unneeded Gen1 check.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dma_to_xxx() macro should exist in same place
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On arm64:
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmaen_init':
sound/soc/sh/rcar/dma.c:180:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)id);
^
include/linux/dmaengine.h:1185:75: note: in definition of macro 'dma_request_channel'
#define dma_request_channel(mask, x, y) __dma_request_channel(&(mask), x, y)
^
Add an intermediate cast to "uintptr_t" to kill the compile warning.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_of_parse_ctu() is not used outside this file so it can be static.
Fixes the following sparse warning:
sound/soc/sh/rcar/ctu.c:72:6: warning: symbol 'rsnd_of_parse_ctu' was
not declared. Should it be static?
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
84e95355602c("ASoC: rsnd: show debug message for SSI/SRC/DVC connection")
added debug message on rsnd_dai_connect(), but the relationship of
parameter check was absurdity. This patch tidyup it.
It is reported via Smatch/Dan
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds CTU (Channel Transfer Unit) support for rsnd driver.
But, it does nothing to data at this point, but is required for MIX
support.
CTU design is a little different from other IPs (CTU0 is including
CTU00 - CTU03, and CTU1 is including CTU10 - CTU13, these have different
register mapping) We need to care about it on this driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is assuming Audio DMAC / Audio DMAC peri peri
are used from SSI/SSIU/SRC/DVC. But we will add CTU/MIX to this driver.
Then, current DMA path searching method is not understandable, and good
enough for this purpose. This patch update DMA path search method, more
simply.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is cleanup for CTU/MIX support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes we would like to get each module directly, especially data path
searching. this patch adds rsnd_io_to_mod() macro, and existing
rsnd_io_to_mod_xxx() use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using Audio DMAC (via DMAEngine) and
Audio DMAC peri peri (via original method), and usage of these DMAC
are different. Indicates its naming is useful for debugging.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC doesn't support Gen1, check it beginning of probe
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dma_ops is used only from dma.c, rsnd.h doesn't need it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can help for connection debug
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sound L/R order of SSI is different from Linux sound data order.
So current rsnd driver is using DALIGN (= data align) to exchange data
align on SSIU. OTOH, CMD/SRC/SSIU have DALIGN register. Now inverted
sound volume will be exchanged if user used volume control on DVC.
Because SSIU which exchanges data align is located after DVC.
MEM -> SRC -> DVC -> SSI
This patch exchanges data align SRC if possible
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has rsnd_get_adinr_bit() to get bit settings for
ADINR (= Audio Information Register) of SSIU/SRC/DVC.
This patch adds rsnd_get_adinr_chan() to get channel settings for
ADINR (= Audio Information Register) of CTU/MIX.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound IP (= SSIU/SRC/CTU/MIX/DVC) have ADINR
(= Audio Information Register), but some of them (= SSIU/SRC/DVC)
are for audio data bits, some of them (= CTU/MIX) are for audio data
channels.
Current rsnd driver is supporting SSIU/SRC/DVC, and these ADINR were
for bits. This patch rename rsnd_get_adinr() to rsnd_get_adinr_bit(),
and we will have rsnd_get_adinr_chan() for CTU/MIX.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas SCU (Sampling Rate Convert Unit) includes SRC/CTU/MIX/DVC,
and these have similar register. xxxIR (Initialization Register) is one
of them. These xxxIR need be set to 1 during initialization.
Current rsnd driver has src.c / dvc.c, and we will have mix.c.
It is readable if these have same named function.
This patch adds rsnd_src_initialize_lock/unlock() and make sure it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas SCU (Sampling Rate Convert Unit) includes SRC/CTU/MIX/DVC,
and these have similar register. xxxIR (Initialization Register) is one
of them. These xxxIR need be set to 1 during initialization.
Current rsnd driver has src.c / dvc.c, and we will have mix.c.
It is readable if these have same named function.
This patch adds rsnd_dvc_initialize_lock/unlock() and make sure it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current sound data route settings is done in dvc.c, and it doesn't care
about CTU/MIX at this poinnt, but we need to care about these.
OTOH, rsnd driver already has rsnd_path_xxx() functions for data path which
are good match for CTU/MIX/DVC path selectio.
This patch adds new rsnd_path_parse() to select sound data route which will
care about CTU/MIX/DVC path.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
parse/break is a little ambiguous/confusable name for rsnd module path.
Especially for CTU/MIX support. It was renamed to add/remove
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas SCU (Sampling Rate Convert Unit) includes SRC/CTU/MIX/DVC,
and these have similar register. xxxRSR (Software reset Register) is one
of them. These xxxRSR need be set to 1 to 0 when software reset.
Current rsnd driver has src.c / dvc.c, and we will have mix.c.
It is readable if these have same named function.
This patch adds rsnd_src_soft_reset() and make sure it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas SCU (Sampling Rate Convert Unit) includes SRC/CTU/MIX/DVC,
and these have similar register. xxxRSR (Software reset Register) is one
of them. These xxxRSR need be set to 1 to 0 when software reset.
Current rsnd driver has src.c / dvc.c, and we will have mix.c.
It is readable if these have same named function.
This patch adds rsnd_dvc_soft_reset() and make sure it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_src_nr() is used only from src.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dvc_nr() is used only from dvc.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
enabling to use same method for exception case is useful.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We couldn't use SRC sync convert mode together with DVC,
but we can use workaround for it.
This patch adds workaround and can use SRC sync convert + DVC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'5451ea443b ("ASoC: rsnd: count each mod (SSI/SRC/DVC)")' counts each
module's callback status, but counts 1st callback only.
This patch fixup it. Otherwise, multi-called function will be trouble
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
based on datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
based on datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current checkpatch.pl indicates 'out of memory' message is unnecessary.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current checkpatch.pl indicates 'out of memory' message is unnecessary.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current checkpatch.pl indicates 'out of memory' message is unnecessary.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
using common audio routing path method makes sense.
Let's use snd_soc_of_parse_audio_route/prefix.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_force_write() is similar to rsnd_write(),
but rsnd_force_write() write data to register even though
it is same value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'047000278da3a17f8("ASoC: rsrc-card: cleanup for DPCM")'
cleanuped rsrc-card driver, but then, unused ret was left.
Below warning happen without this patch
${LINUX}/sound/soc/sh/rcar/rsrc-card.c: In function 'rsrc_card_startup':
${LINUX}/sound/soc/sh/rcar/rsrc-card.c:78:6: warning: unused variable \
'ret' [-Wunused-variable]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many path
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. rsnd_mod_to_io() is no longer needed. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship.
This patch checks module working status via io instead of mod
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. This patch removes rsnd_mod_to_io() from snd_kcontrol
and related function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. This patch removes rsnd_mod_to_io() from rsnd_src_xxx()
and related function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. This patch removes rsnd_mod_to_io() from rsnd_ssi_xxx()
and related function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. This patch removes rsnd_mod_to_io() from rsnd_dma_xxx()
and related function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. This patch removes rsnd_mod_to_io() from rsnd_get_adinr()
and its related function
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. Then, interrupt handler can't use rsnd_mod_to_io().
This patch adds SSI/SRC/DMA common interrupt handler frame
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. This means we can't call rsnd_mod_to_io() any more.
This patch adds struct rsnd_dai_stream to each function as parameter.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. In such case, mod <-> io is no longer 1:1
relationship. This means we can't use rsnd_mod_to_io() in SSI/SRC/DMA
interrupt handler. In such case, we need to check all io in interrupt
handler, and then, "priv" is needed.
This patch adds rsnd_priv pointer in rsnd_mod for prepare it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each Renesas sound mod (= SSI/SRC/DVC) might be called from many paths
if it supports MIXer. Then, we don't need to re-call each mod function
that had been called. This patch count each mod status.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsrc-card driver is based on simple-card driver which is caring about
CPU / Codec connection. OTOH, rsrc-card is used for DPCM system.
FE portion is constituted by CPU and dummy Codec, and BE is constituted
by dummy CPU and Codec in DPCM system.
Because of this, current rsrc-card is doing pointless method. It works well
if FE/BE was 1:1, but not good for multi FE/BE.
This patch cleanups rsrc-card driver for DPCM. and this is prepare for
MIX support for Renesas sound driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is prepare for DPCM cleanup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsrc-card is assuming 1 FE (= CPU), 1 BE (= codec) on card.
But, it will support multi FE/BE card. This is prepare for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current dai_link name is using "cpu_dai_name + codec_dai_name",
but one of them is always "snd-soc-dummy-dai" when DPCM.
This patch uses "fe.xxx" for cpu, "be.xxx" for codec.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'a9e1ac1a9e4585b5("ASoC: rsnd: spin lock for interrupt handler")'
added spin lock under interrupt handler to solve HW restart issue.
OTOH, current rsnd driver calls snd_pcm_period_elapsed() from
rsnd_dai_pointer_update(). but, it will be called under spin lock
if SSI was PIO mode.
If it was called under spin lock, it will call
snd_pcm_update_state() -> snd_pcm_drain_done().
Then, it calls rsnd_soc_dai_trigger() and will be dead-lock.
This patch doesn't call rsnd_dai_pointer_update() under spin lock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PIO is used only for checking data path / codec settings. And underrun
is very normal when PIO mode. Let's don't care about under/over run
error when PIO case. Otherwise, 1) too many HW restart happens, 2) some
sounds which need much data transfer can't play since it falls into
error detection method which was created for DMA transfer
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver calls rsnd_dai_stream_init() when
start, but it didn't call paired function. This patch adds
rsnd_dai_stream_quit() for it. This is prepare for interrupt error
status check feature support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Tested by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi_hw_stop() should be called after rsnd_ssi_hw_start().
This patch indicates unknown hw_stop as error
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Tested by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 'e9c390df671f ("ASoC: rsnd: make sure it uses lock when
it calls rsnd_dai_call)' The additional locks make 1") lock issue when boot
2) lock issue when unbind/rmmod. And there is no problem without these
locks. This patch revert it.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd might be used in multi-codec sound card.
Then, same name kcontrol will be registered many times, and it will
be error. This patch fixes this issue by using .index
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI parent/child need to use same number of sound data channel
if these are sharing clock/ws pin. this patch makes it sure.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver is using SSI parent related function/macro as
"clock" related. but it is not only clock related.
tidyup function/macro naming.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_call() should be called under rsnd_lock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using standardized function/macro name is useful in driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dmaen_quit() is assuming dmaen->chan is NULL if it failed
to get DMAEngine channel. but, current dmaen->chan might have
error value when error case (this driver is checking it by IS_ERR_OR_NULL())
This patch makes sure dmaen->chan is NULL when error case.
Otherwise, it will contact to unknown address in rsnd_dmaen_quit()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound SRC (= Sampling Rate Converter) has
Asynchronous/Synchronous SRC mode. Asynchronous mode is already
supported via DPCM. This patch adds Synchronous mode on it.
The condition of enabling Synchronous mode are
- SoC is clock master
- Sound uses SRC
- Sound doesn't use DVC
- Sound card uses DPCM (= rsrc-card card)
amixer set "SRC Out Rate" on
aplay xxx.wav &
amixer set "SRC Out Rate" 48000
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A driver's device data should and can be const. This is a follow-up on
commit 33187fb4a2 (ASoC: rsnd: constify of_device_id array) which
marked the of_device_id as const.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch supports DPCM based sampling rate convert on Renesas sound
driver. It assumes...
1. SRC is implemented as FE
2. BE dai_link supports .be_hw_params_fixup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes useless debug message. especially some kind of
"probed" message will be printed from core.c if it has #define DEBUG
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable()/clk_disable_unprepare() uses mutex inside,
in concretely clk_prepare()/clk_unprepare().And it uses __schedule().
Then, raw_spin_lock/unlock_irq() is called, and it breaks Renesas
sound driver's spin lock irq.
This patch separates thesse into clk_prepare()/clk_unprepare() and
clk_enable/clk_disable. And call clk_prepare()/clk_unprepare() from
probe/remove function. Special thanks to Das Biju.
Reported-by: Das Biju <biju.das@bp.renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd-dpcm-card is supporting DPCM FE/BE sound card.
This patch adds .be_hw_params_fixup and enabled sampling convert rate.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound card has "sampling rate convert" feature which
should be implemented via DPCM.
But, sound card driver point of view, it is difficult to add
this DPCM feature on simple-card driver. Especially, DT binding
support is very difficult.
This patch implements DPCM feature on DT as Renesas specific sound card.
This new driver is copied from current simple-card driver.
Main difference between simple-card and this driver are...
1. removed unused feature from simple-card
2. removed driver named prefix from DT property
3. CPU will be FE, CODEC will be BE with snd-soc-dummy
4. it supports sampling rate convert via .be_hw_params_fixup
5. board specific routing is implemented in driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace duplicated const keyword for 'dvc_ramp_rate' with proper
array of const pointers to const strings.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing dai_link stream_name
which is used when DPCM
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver sometimes fixups debug/error message format
30cc4faf70
(ASoC: rsnd: tidyup debug message format and timing)
337b0b4c5f
(ASoC: rsnd: error meesage indicates its port)
But, it still exist un-fomated error message. This patch fixup it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will be SRC interrupt endless loop f unusual situation happen.
This patch adds restart limit for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It will be SSI interrupt endless loop f unusual situation happen.
This patch adds restart limit for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver needs SSI/SRC/DVC regmaps, but it didn't have
regmap_config::name for devm_regmap_init_mmio().
Thus, debugfs initialization code tried to use same driver name
many times, and failed.
This patch adds eacy own name for regmap_config::name
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver needs 1st/2nd DMA interface,
and 1st DMA is using DMAEngine, and 2nd is using local method now.
2nd DMA had been DMAEngine, but it was moved to local method by previous
patchset. But then, it lost PIO mode fallback when probe.
this patch recovers it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/sh/rcar/dma.c: In function 'rsnd_dmapp_init':
sound/soc/sh/rcar/dma.c:341:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
dev_dbg(dev, "id/src/dst/chcr = %d/%x/%x/%08x\n",
^
sound/soc/sh/rcar/dma.c:341:2: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t' [-Wformat=]
Fixes: 288f392e72 ("ASoC: rsnd: add Audio DMAC peri peri support rework")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
dma-names on DT was implemented as no difference between 1st / 2nd
DMAC's, since rsnd had assumed that both DMACs are implemented as
DMAEngine. That style was "src_dst". But now, 2nd DMAC was implemented
as non DMAEngine, and it doesn't need dma-names anymore. So, this
dma-names rule is no longer needed.
And additionally, dma-names was assumed that it has all
(= SSI/SSIU/SRC/DVC) nodes under sound node.
In upstream code, no SoC/platform is supporting DMA for rsnd driver yet.
This means there is no compatible issue if this patch changes
dma-names's rule of DT.
This patch assumes dma-names for 1st DMAC are tx/rx base, and listed
in each SSI/SRC/DVC subnode
ex)
rcar_sound,dvc {
dvc0: dvc@0 {
dmas = <&audma0 0xbc>;
dma-names = "tx";
};
...
rcar_sound,src {
src0: src@0 {
...
dmas = <&audma0 0x85>, <&audma1 0x9a>;
dma-names = "rx", "tx";
};
...
rcar_sound,ssi {
ssi0: ssi@0 {
...
dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
dma-names = "rx", "tx", "rxu", "txu";
};
...
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds rsnd_dvc_of_node() to get DVC subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds rsnd_src_of_node() to get SRC subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds rsnd_ssi_of_node() to get SSI subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound driver uses SSI, but the DMA interfaces are
SSI/SSIU. This interface is based on SSI/SRC/DVC connection.
And DMA function needs to know which interface is used somehow.
This patch enables rsnd_ssi_use_busif() for DMA.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car needs 2 DMACs.1st DMAC is DMAEngine, and 2nd DMAC is
implemented as local code. These 2 DMACs are never shared.
We can use union for these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMAEngine direction can be calculated from rsnd_dai_stream,
So, rsnd_dma::dir does not make sense now.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMAEngine for Renesas R-Car driver is used only for Audio DMAC now.
rsnd_dma::addr was added to support Audio DMAC peri peri,
but it is no longer needed. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
Audio DMAC peri peri is controlled from sound driver without DMAEngine
by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd driver needs to care about Audio DAMC (via DMAEngine),
Audio DMAC peri peri (via local method) on rsnd driver.
This patch adds new rsnd_dma_ops and care it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now, we have dma.c for Audio DMAC / Audio DMAC peri peri.
rsnd_gen_dma_addr() should go there.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound driver had been assumed that Audio DMAC /
Audio DMAC peri peri are implemented by DMAEngine. But, result of DMA
ML discussion, it was concluded that it is not a general purpose DMAC.
And it should be moved from current DMAEngine to rsnd driver.
So, Audio DMAC peri peri become non DMAEngine.
OTOH, ALSA SoC has soc-generic-dmaengine-pcm implementation. but it
seems difficult to use this generic implementation on rsnd driver at
this point, since it needs to fallback to PIO mode if DMA can't use.
and additionally it needs 2 DMAC (= Audio DMAC / Audio DMAC peri peri).
These are not "generic" feature.
Of course I will try to use this generic dmaengine in the future somehow,
but just use current style at this point until it can formally use 2 DMACs.
This patch adds new dma.c and moves current dma code to dma.c from core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
physical address is required from Audio DMAC peri peri.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd driver needs to support Audio DMAC peri peri inside sound driver.
getting resource by name is useful for it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dma_available() is not used. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It can get DMA direction via rsnd_dai_stream.
Remove un-needed is_play from rsnd_dma_init().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound had SH-DMA-BASE specific implementation before,
but, now, it is no longer needed. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set device data before snd_soc_register_platform/component.
Otherwise, it will use NULL pointer if user calls unbind -> bind or
rmmod -> insmod
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver is using snd_ctl_xxx()
functions, but it didn't call snd_ctl free_one() / snd_ctl_remove().
This patch call these functions.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: Bui Duc Phuc <bd-phuc@jinso.co.jp>
Reported-by: Cao Minh Hiep <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current R-Car sound driver calls SRC -> SSI -> DVC functions,
but, it should be DVC -> SRC -> SSI.
Otherwise, SSI (= interface of codec) will have underrun error
when playback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DMA starts after SSI, and stops before SSI. but we need
to reverse these order. Otherwise, under/over run error might happen.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI interrupt handler of R-Car sound driver will be called
when DIRQ (= Data read/write timing for PIO) or
UIRQ / OIRQ (= under/over run error).
DIRQ "interrupt" doesn't occur when DMA transfer, but then,
DIRQ "status bit" might occur. we need to ignore this DIRQ
operation when DMA. Otherwise, driver will push/pop as PIO.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SRC/SSI output its error, but it desn't indicate
port number. it is un-understandable.
Let's indicate port number for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has rsnd_mod_to_priv() macro, and struct rsnd_mod
has struct rsnd_priv pointer. But, it is waste of memory from data
structure point of view.
Today we can link mod <-> io <-> rdai each other, so saving priv in
rdai is very reasonable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's function requests rdai, but it is not used.
Adding priv is more reasonable. Let's replace it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's many functions requests struct rsnd_dai (= rdai),
but, 1) we can get rdai from rsnd_io_to_rsnd(), 2) almost all rdai
is not used. Let's remove these rdai.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver can use rsnd_io_to_rdai()
we can get play/capture direction via io now.
Let's replace rsnd_dai_is_play() to rsnd_io_is_play()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver request rdai in everywhere, but each mod should
reach to rdai by itself. this patch adds missing rsnd_io_to_rdai().
io = rsnd_mod_to_io(mod);
rdai = rsnd_io_to_rdai(io);
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_get_platform_info() is not used. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dai_id() was not used. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct rsnd_dai is called as "rdai", and struct snd_soc_dai is called
as "dai" on this driver. but macro/function have confusable naming.
This patch rename rsnd_dai_is_clk_master() to rsnd_rdai_is_clk_master()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct rsnd_dai is called as "rdai", and struct snd_soc_dai is called
as "dai" on this driver. but macro/function have confusable naming.
This patch rename rsnd_dai_get() to rsnd_rdai_get()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver's mod (= ssi/src/dvc) have each own clk,
but, these are needed to start/stop each mod.
This patch adds struct clk in rsnd_mod, and start/stop these
via rsnd_mod_hw_start/stop() macro
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_ssi::rate is not used. Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
L/R channel will be switched if under/over flow error happen on
Renesas R-Car sound device by the HW bugs. Then, HW restart is required
for salvage. This patch add salvage support for SRC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALSA core takes care that all preallocated memory is freed when the PCM
itself is freed. There is no need to do this manually in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current R-Car sound SSI PIO/DMA mode are using interrupt.
it is no longer "xxx_pio_xxx", rename it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
L/R channel will be switched if under/over flow error happen on
Renesas R-Car sound device by the HW bugs. Then, HW restart is required
for salvage. This patch add salvage support for SSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_src_start/stop() requests struct rsnd_dai as parameter.
but, it is not used, and become more complex in L/R error handling.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Basically, SSI starting method is same between PIO/DMA mode.
Let's share it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current src.c sets SRC_ROUTE_MODE0 on rsnd_src_start(), but, set it in
rsnd_src_set_convert_rate() is natural.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current src initialize SRC on rsnd_src_set_convert_rate()
but, it should be done on rsnd_src_init().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
using many rsnd_src_convert_rate() is not readable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DVC is using snd_kcontrol_new functions, but, SRC will need
same method. Move common functions to core.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
master clock rate is useful information for debug.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI start/stop sequence is different between PIO/DMA mode,
but, almost all are same. this patch synchronize it.
It will be shared in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's clear SSI status when HW start
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI is careing SSIWSR which controls WS continue mode when
DMA mode, but, it should be cared when PIO mode too.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current SSI doesn't care interrupt "disable" method. And, it is used
when PIO mode only at this point. SSI interrupt will be used for
sound R/L issue workaround when DMA mode too.
This patch tidyup SSI interrupt enable/disable method.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ssi.c has .cr_etc which is used for SSICR's
etc settings. but, it is used as PIO/DMA switching purpose now.
This patch tidyup this method. This is prepare for
under/over run issue handling
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_src_ssiu_stop() is used to stop SSIU,
but it shouldn't depend on whether it is using SSIU.
This patch stops SSIU compulsorily.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car sound can use SSI/SRC/DVC modules, and these are controlled as
rsnd_mod in rsnd driver. These rsnd_mod has each own function as
callback. Basically these callback function has pair like probe/remove,
start/stop, etc. And, these functions are called by order to each stage
like below.
1. src->probe
2. ssi->probe
3. dvc->probe
4. src->start
5. ssi->start
6. dvc->start
7. src->stop
8. ssi->stop
9. dvc->stop
10. src->remove
11. ssi->remove
12. dvc->remove
But, current rsnd driver doesn't care about its status which indicates
which function is called.
For example, if 5) returns error, 6) is not called. In such case,
9) should not be called. This patch care about each modules status.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current R-Car sound has PIO fallback support if it couldn't use DMA.
This fallback is done in .remove callback, but, it should have
.fallback callback. Otherwise, normal .remove callback will have
strange behavior. This patch adds .fallback callback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Volume Ramp to Renesas sound driver.
amixer set "DVC Out" 100%
amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
amixer set "DVC Out Ramp" on
aplay xxx.wav &
amixer set "DVC Out" 80% // Volume Down
amixer set "DVC Out" 100% // Volume Up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver probe will be failed
if it try to use DMA mode and it couldn't use for some reasons.
But PIO mode works even though in such case.
This patch try to fallback to PIO mode if DMA mode probing was failed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas R-Car sound driver debug message
is using random format
(ex "ssi0: xxx" / "SSI0 xxx" / "ssi[0]: xxx")
and confusable timing
("xxx probe failed" and "xxx probed" are shown in same time)
This patch fixes these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Volume Ramp is listed as "XX dB / YY steps",
and this enumerated settings are easy for users.
This patch adds rsnd_dvc_cfg_e and care about
enumerated settings.
Compiler will report like below at this point,
but, it will be removed if Volume Ramp was supported.
warning: '_rsnd_dvc_pcm_new_e' defined but not used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Some of them requests values for "each channels",
but, some of them requests values for "feature".
And, Volume Ramp has "feature" settings.
This patch adds rsnd_dvc_cfg_s and care about
single settings.
Compiler will report like below at this point,
but, it will be removed if Volume Ramp was supported.
warning: '_rsnd_dvc_pcm_new_s' defined but not used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC controls some digital volume features.
Some of them requests values for "each channels",
but, some of them requests values for "feature".
Current dvc.c is supporting Mute/Volume,
and these have "each channels" settings.
This patch adds rsnd_dvc_cfg_m and care about
multiple settings for each channels.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to Enable/Disable DVC_DVUER register if we set
DVCp_ZCMCR, DVCp_VRCTR, DVCp_VRPDR, DVCp_VRDBR,
DVCp_VOL0R, DVCp_VOL1R, DVCp_VOL2R, DVCp_VOL3R,
DVCp_VOL4R, DVCp_VOL5R, DVCp_VOL6R, DVCp_VOL7R
and, these are controlled under rsnd_dvc_volume_update().
This patch moves DVC_DVUER settings to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_dvc_volume_update() is main function to control
DVC feature like Digital Volume / Mute / Ramp etc.
DVC_DVUCR should be controlled under this function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car sound doesn't support PAUSE.
Remove SNDRV_PCM_INFO_PAUSE flags from snd_pcm_hardware info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
DVC can control Digital Volume / Mute / Volume Ramp etc,
and these uses different max value.
Current driver is using fixed max value for each settings.
This patch adds new struct rsnd_dvc_cfg, and control these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RSND_DVC_VOLUME_NUM means DVC channel number.
This patch tidyups this un-understandable naming
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
b8c637864a
(ASoC: rsnd: use regmap_mmio instead of original regmap bus)
added regmap_mmio support on Renesas R-Car sound driver.
Then, debug information of register read/write
indicates regmap index, not register address.
This is a little bit confusable information.
This patch tidyup debug message, and added regmap debug hint
on comment area.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse spits out the following warning:
sound/soc/sh/rcar/gen.c:250:21: warning: dubious: x & !y
It does this because sometimes mixing boolean and bit-wise logic has not the
intended result. In this case we are fine, but replacing the bit-wise '&' with
the boolean '&&' silences the sparse warning. The generated code for both cases
is the same.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
DVC can control Mute.
This patch supports it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DVC can use Volume and Mute control,
and these control methods doesn't have much difference.
This patch cleanup current method,
and it will be used for Mute control.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In current R-Car rsnd driver,
the SND_SOC_DAIFMT_xB_xF flags are used to HW default behavior,
but, it should be used to specific format.
The waveforms of LEFT_J/RIGHT_J format with
SND_SOC_DAIFMT_NB_NF flag will be
started from "falling edge" without this patch.
But, it should be started from "rising edge".
Reported-by: Jun Watanabe <jun.watanabe.ue@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
bff58ea4f4
(ASoC: rsnd: add DVC support) added DVC support,
and it added pcm_new callback feature for it.
Then it called all DAI's pcm_new callback, and it was wrong.
This patch fixup it and call correct callback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
b8c637864a
(ASoC: rsnd: use regmap_mmio instead of original regmap bus)
used regmap_mmio and modified dev_dbg() for rsnd_read/write().
But rsnd_bset() is missing it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound uses Audio Local Bus which uses Lch/Rch format.
This bus is used if driver uses BUSIF.
But sound data is written as Rch/Lch format in register.
This means Rch <-> Lch will be inverted.
SSIU :: BUSIF_DALIGN is used to controlling data format.
Reported-by: Jun Watanabe <jun.watanabe.ue@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Driver should care more detail of SRC_BSDSR settings.
The sound includes noise without this patch
if it used SRC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rsnd driver is using regmap and regmap_field.
It used original regmap bus which is
single regmap instance for multi register mapping.
This patch modifies it to use regmap_mmio bus,
and tidyuped probe method
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rsnd driver is using SSI/SRC/DVC which are
using "mod" base operation.
These "mod" are supporting "probe" and "remove" callbacks.
Current rsnd_probe should call "remove" if "probe" was failed,
since "probe" might be having DMAEngine handle.
Some mod's "remove" callback might be called without calling
"probe", but it is no problem. because "remove" do nothing
in such case.
So, all mod's "remove" should be called when error case
of rsnd_probe() and rsnd_remove().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound uses Audio DMAC and Audio DMAC peri peri.
Audio DMAC peri peri transfers data inside circuit.
DMA transfer needs source / destination address,
and destination address can be set via dmaengine_slave_config().
The source address can be set when starting DMAEngine.
Because Audio DMAC peri peri always ignores its value,
current driver always used same source address for
Audio DMAC / Audio DMAC peri peri
(Audio DMAC peri peri source / destination address
is always fixed value)
But, This is not good match for DT booting.
This patch properly uses DMA start address
for Audio DMAC / Audio DMAC peri peri.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current R-Car sound SSI/SRC/DVC selection has feature limit.
(It is assuming that SSI/SRC are using same index number)
So that enabling SSI/SRC flexible selection,
this patch modifies DMA settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current DVC can be enabled only when playback,
but, this came from misunderstanding.
It is not correct.
DVC <-> DMA relationship is...
Playback: MEM -> DMAC -> SRC -> DVC -> DMACp -> SSI
Capture: SSI -> DMACp -> SRC -> DVC -> DMAC -> MEM
DVC can be used for both Playback/Capture
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current R-Car sound driver is using DMAEngine directly,
but, ASoC is requesting to use common DMA transfer method,
like snd_dmaengine_pcm_trigger() or dmaengine_pcm_ops.
It is difficult to switch at this point, since Renesas
driver is also supporting PIO transfer.
This patch uses dmaengine_prep_dma_cyclic() instead
of dmaengine_prep_slave_single().
It is used in requested method,
and is good first step to switch over.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Sound data needs to be sent to R-Car sound SSI when playback.
But, there are 2 interfaces for it.
1st is SSITDR/SSIRDR which are mapped on SSI.
2nd is SSIn_BUSIF which are mapped on SSIU.
2nd SSIn_BUSIF is used when DMA transfer,
and it is always used if sound data came from via SRC.
But, we can use it when SSI+DMA case too.
(Current driver is assuming 1st SSITDR/SSIRDR for it)
2nd SSIn_BUSIF can be used as FIFO.
This is very helpful/useful for SSI+DMA.
But DMA address / DMA ID are not same between 1st/2nd cases.
This patch care about these settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
dmaengine_prep_slave_single() expects a enum dma_transfer_direction and not a
enum dma_data_direction. Since the integer representations of both DMA_TO_DEVICE
and DMA_MEM_TO_DEV aswell as DMA_FROM_DEVICE and DMA_DEV_TO_MEM have the same
value the code worked fine even though it was using the wrong type.
Fixes the following warning from sparse:
sound/soc/sh/rcar/core.c:227:49: warning: mixing different enum types
sound/soc/sh/rcar/core.c:227:49: int enum dma_data_direction versus
sound/soc/sh/rcar/core.c:227:49: int enum dma_transfer_direction
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current dma name search loop didn't care about SSI index
This patch fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ad32d0c7b0
(ASoC: rsnd: add rsnd_gen_dma_addr() for DMAC addr)
added rsnd_gen_dma_addr() to calculate DMA addr,
but, it is necessary only for Gen2.
This patch ignores Gen1 case.
Kernel will be panic without this patch.
Special thanks to Simon
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@linaro.org>
Index of dma name should use -1, not +1 when capture case.
Thank you Dan.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMAC src/dst addr needs to be set from driver when DT case.
(It was set from SoC/DMAEngine code when non-DT case)
This patch adds rsnd_gen_dma_addr() to set DMAC src/dst addr.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound driver is supporting to use DMAEngine.
But, DMA slave channel name "tx", "rx" is not enough
in DT case.
Becuase, it has many ports and path combination.
This patch adds rsnd_dma_of_name() to find
DMA channel name, for example
memory to SSI0 is "mem_ssi0",
SSI0 to memory is "ssi0_mem",
SSI0 to SRC0 is "ssi0_src0",
SRC0 to SSI0 is "src0_ssi0",
SRC0 to DVC0 is "src0_dvc0"...
Renesas sound want to use PIO transfer mode for some reasons.
It will be PIO tranfer mode if device node doesn't have
DMA settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound driver uses many modules (= SSI/SRC/DVC),
and each module had own name.
But, each module name can be used as several purpose,
like clock name, DMA name etc...
This patch uses common name for each module.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Renesas sound driver is supporting Gen1/Gen2.
SRC probe can return error if it was unknown
generation.
Now, rsnd_src_non_ops is not needed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DT DMA support needs struct platform_device pointer,
and it can get struct device pointer from platform_device.
Save platform_device instead of device.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Driver needs to call of_node_put() after of_get_chile_by_name()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the %pap printk specifier to print resource_size_t variables. This
fixes warnings on platforms where resource_size_t has a different size
than int.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds DVC (Digital Volume Controller)
support which is member of CMD unit.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rsnd_mod_ops would like to come to use multi parameter.
modify macro to enable it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now, it can get rsnd_dai_stream pointer from rsnd_mod.
Remove duplicate parameter from rsnd_mod_ops
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SRC module needs ADINR register settings,
but, it has many similar xxx_ADINR register,
and needs same settings.
This patch adds rsnd_get_adinr() to sharing code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current R-Car sound supports only SRC/SSI,
but, other module will be supported.
This patch adds rsnd_path_parse() macro to share code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now, all platform is using new style rsnd_dai_platform_info.
Keeping compatibility is no longer needed.
We can cleanup code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All platform which used old style was
switched to new style.
R-Car sound can remove old style clock support,
use device dependent clock now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rsnd_soc_dai_trigger() will be called
after rsnd_dai_pointer_update() function
which is using rsnd_lock().
Thus, it should be called from outside of rsnd_lock().
Kernel will be hangup without this patch.
Special thanks to Kataoka-san
Reported-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As with the previous commit, before a clock can be used it must be prepared
for use. Change from clk_enable() and clk_disable() to the versions of the
calls which also prepare and un-prepare the clocks.
Will fix warnings from the clock code when this is used.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
src might not exist.
kernel will be hung-up without this patch in such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C5oo
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.15' into asoc-next
ASoC: Updates for v3.15
Quite a busy release for ASoC this time, more on janitorial work than
exciting new features but welcome nontheless:
- Lots of cleanups from Takashi for enumerations; the original API for
these was error prone so he's refactored lots of code to use more
modern APIs which avoid issues.
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle.
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues.
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues.
- DPCM support for Intel Haswell and Bay Trail platforms.
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC.
# gpg: Signature made Wed 12 Mar 2014 23:05:45 GMT using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
Support for loading the Renesas R-Car sound driver via DeviceTree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SND_SOC_DAIFMT_CBx_CFx means "codec" side master/slave mode.
Then, rcar will be master mode if it was SND_SOC_DAIFMT_CBS_CFS.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car sound has SCU unit which has SRC/CTU/MIX/DVC,
and current rsnd driver has scu.c and scu module.
Current scu.c has SRC support only.
My first concept was control these feature on scu.c
but, it become difficult and un-understandable now.
This patch rename scu to src
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now, rsnd_xxx_remove() do nothing.
remove these
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rsnd_dai_remove() called rsnd_path_exit(),
but these memory will be cleaned automatically.
Because it is created by devm_kzalloc().
nothing to do on rsnd_dai_remove()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Each rsnd mod needs specific probe method,
and its best timing is DAI probe timing.
But current code runs it mod probe timing.
This patch adds new probe/remove callback to solve it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current R-Car sound driver is assuming that
SCU mod is used even though it is not needed.
Because scu.c is controlling SSIU too.
(it is Gen1 compatibility)
But, SCU mod will be really not used if new platform dai
feature was added.
Thus, rsnd_scu_ssi_mode_init() is called from SSI
directory by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Kuninori Morimoto