The I2C init path forgot to init the mutex, leading to an oops when
controls are accessed.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Save a bit of scheduling by coalescing all the output power up delays
into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give the output disable sequence a chance to fully complete, otherwise
there is a danger we may remove the clock before it is finished
resulting in a pop noise. The delay for each output must be cumulative
and these are coalesced into a single delay.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add description for the driver
- Add dependency on the I2C module
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
make the sta32x driver usable with device tree configs. Code is heavily based
on the sta350 driver.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The reset GPIO on the STA32X Codecs is used to reset the Codec and clear
all registers. Also taking it down puts the IC in power save mode, so
we put the device in reset mode when we go to sleep.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
use the regmap API directly rather than relying on the snd_soc_read/write
functions as this seems to be in accordance with common practice.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IDE bit in the CONFF register is the third bit not the fourth.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Asus T100TAF uses ACPI ID "10EC5642" for its audio codec. I suppose it is
updated ACPI ID for the RT5642 codec since some earlier platforms are using
"10EC5640" with the RT5642 too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The purpose of rt286_adc_event is to mute/numnte the ADC mixer.
However, it will also set the capture volume to default value.
As a result, "ADC0 Capture Volume" is not working if it is set
before capture start. This patch remove rt286_adc_event and add
"ADC0 Capture Switch" to mute/unmute ADC mixer.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm97xx touchscreen driver binds itself to the snd_ac97 device that gets
registered by the CODEC driver and expects that the device has already been
reset. Before commit 6794f709b7 ("ASoC: ac97: Drop delayed device
registration") the device was only registered after the probe function of
the CODEC driver had finished running, but starting with the mentioned
commit the device is registered as soon as snd_soc_new_ac97_codec() is
called. This causes the touchscreen driver to no longer work. Modify the
CODEC drivers to use snd_soc_alloc_ac97_codec() instead of
snd_soc_new_ac97_codec() and make sure that the AC'97 device is reset before
the snd_ac97 device gets registered.
Fixes: 6794f709b7 ("ASoC: ac97: Drop delayed device registration")
Reported-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is only one I2S I/F, AD/DA path must operate to the same
format.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we want to use wm8960 codec, we should enable its MCLK in machine driver.
It's reasonable for wm8960 codec driver to manage its own MCLK.
When current bias_level is SND_SOC_BIAS_ON, it is preparing for a transition
away from ON. In this case, disable the codec mclk. When current bias_level
is not SND_SOC_BIAS_ON, it preparing for a transition to ON. In this case,
enable the codec mclk.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mc13783 driver uses inverted semantics for the tx_mask and rx_mask
parameter of the set_tdm_slot() callback compared to rest of ASoC. This
patch updates the driver's semantics to be consistent with the rest of ASoC,
i.e. a set bit means a active slot and a cleared bit means a inactive slot.
This will allow us to use the set_tdm_slot() API in a more generic way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the path name for mux to get rid of the following warning:
--->8---
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTR
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTR
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACL
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACL
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACR
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACR
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the slot_width "25" support in the TDM mode for the Intel platform.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch uses the regmap functions instead of the snd_soc functions in some
cases.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC powerdown bit is managed by DAPM. Manually powering down the DAC in
the CODEC probe function may cause unnecessary power state transitions which
can lead to click and pop noises.
So leave the DAC powerdown bit in its default poweron-reset state and let
DAPM do all the management.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DSP programs are listed out of order.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The patch modified the behavior that updates the PLL parameter. It set the
update bit before the PLL power up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch adds the MICBIAS VDD setting in the platform data. It can be set to
1V8 or 3V3 in the MICBIAS VDD.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces the use of function put_unaligned_be16.
This is done using Coccinelle and semantic patch used is as follows:
@a@
typedef u16, __be16, uint16_t;
{u16,__be16,uint16_t} e16;
identifier tmp;
expression ptr;
expression y,e;
type T;
@@
- tmp = cpu_to_be16(y);
<+... when != tmp
(
- memcpy(ptr, (T)&tmp, \(2\|sizeof(u16)\|sizeof(__be16)\|sizeof(uint16_t)\|sizeof(e16)\));
+ put_unaligned_be16(y,ptr);
|
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_be16(y,ptr);
)
...+>
? tmp = e
@@ type T; identifier a.tmp; @@
- T tmp;
...when != tmp
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
--
Changes Since v2:
Make the patch compatible for current code
sound/soc/codecs/wm5102.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
Signed-off-by: Mark Brown <broonie@kernel.org>
When codec is in slave mode, ASRC can suppress noise for asynchronous
MCLK and LRCLK or special I2S format. This patch defines an API to select
the clock source for specified filters. And the codec driver will turn on ASRC
for these filters if ASRC is selected as their clock source.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The previous definition of registers 0x84 and 0x85 doesn't match the datasheet.
So this patch removes the wrong definition and writes a new one for the two
registers.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8960 codec can't support sample rate 11250, it must be 11025.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
snd_soc_codec_driver (snd_soc_register_codec() accepts pointer to const)
and array of default register values const as well.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
snd_soc_codec_driver const as well (snd_soc_register_codec() accepts
pointer to const).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
snd_soc_codec_driver const as well (snd_soc_register_codec() accepts
pointer to const).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
snd_soc_codec_driver const as well (snd_soc_register_codec() accepts
pointer to const).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
snd_soc_codec_driver const as well (snd_soc_register_codec() accepts
pointer to const).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
snd_soc_codec_driver const as well (snd_soc_register_codec() accepts
pointer to const).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
snd_soc_codec_driver const as well (snd_soc_register_codec() accepts
pointer to const).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
snd_soc_codec_driver const as well (snd_soc_register_codec() accepts
pointer to const).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ts3a227e does not trigger interrupt to report jack status when system
boots from warm reset because ts3a227e's power remains on during warm reset.
Read jack status at probe to get current jack status.
Note that if system boots from EC reset, then this issue will not
happen.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the duplicated PLL1 connections of the adc stereo filters,
and remove the PLL1 connections of the DACs because the PLL1 should be
connected to dac filters.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the filter powers of the dac mono3 and mono4, and remove the connection
of dac stereo1 filter that connect to DAC1 MIX.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_kcontrol_chip should return snd_soc_component instead of
snd_soc_codec
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
System clock is necessary for rt5670 JD function. We assume system
clock source will be set in machine driver. So there are two things
left we should do in codec driver.
1. Set sysclk to codec internal clock in probe since machine driver
may not do that before JD function is registered.
2. Power up PLL once sysclk source is switched to PLL.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds runtime PM support on rt5670 codec.
Signed-off-by: Lin Mengdong <mengdong.lin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch set specific data according to dmi data.
Signed-off-by: Jin, Yao <yao.jin@intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are a few fixes that have landed after the previous pull
request. All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=HRbM
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a few fixes that have landed after the previous pull request.
All are driver specific fixes including:
- error/int value fixes in OXFW,
- Intel Skylake HD-audio HDMI codec support,
- Additional HD-audio Realtek codecs and AD1986A codec fixes/quirks,
- a few more DSD support and a quirk for Arcam rPAC in usb-audio,
- a typo fix for Scarlett 6i6,
- fixes for new ASIHPI firmware,
- ASoC Exynos7 cleanups,
- Intel ACPI support, and
- a fix for PCM512 register cache sync"
* tag 'sound-fix-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
ALSA: usb-audio: extend KEF X300A FU 10 tweak to Arcam rPAC
ALSA: hda/realtek - New codec support for ALC298
ALSA: asihpi: update to HPI version 4.14
ALSA: asihpi: increase tuner pad cache size
ALSA: asihpi: relax firmware version check
ALSA: usb-audio: Fix Scarlett 6i6 initialization typo
ALSA: hda - Add quirk for Packard Bell EasyNote MX65
ALSA: usb-audio: add native DSD support for Matrix Audio DACs
ALSA: hda/realtek - New codec support for ALC256
ALSA: hda/realtek - Add new Dell desktop for ALC3234 headset mode
ASoC: Intel: fix possible acpi enumeration panic
ALSA: hda/hdmi - apply Haswell fix-ups to Skylake display codec
ASoC: Intel: fix return value check in sst_acpi_probe()
ALSA: hda - Make add_stereo_mix_input flag tristate
ALSA: hda - Create capture source ctls when stereo mix input is added
ALSA: hda - Fix typos in snd_hda_get_int_hint() kerneldoc comments
ALSA: hda - add codec ID for Skylake display audio codec
ALSA: oxfw: some signedness bugs
ALSA: oxfw: fix detect_loud_models() return value
ASoC: rt5677: add REGMAP_I2C and REGMAP_IRQ dependency
...
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under sound/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Commit 04489eeb02 ("ALSA: wm8750: add missing VREF output") added the
previously missing VREF widget. And while adding the widget as OUTPUT widget
silences the error of the missing widget it should have rather been a VMID
widget.
The VREF widget is only used internally as a source for the VREF input of
the Out3 Mux. Selecting that input means that the path should be kept
powered up at the VREF/VMID voltage, but that there is no actual audio
signal. Using a VMID widget will do this, whereas using a OUTPUT widget will
simply cause the path to completely power down.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec driver uses regmap to do i2c read/write.
The codec driver started to use REGMAP_IRQ since:
5e3363ad1b
ASoC: rt5677: add GPIO IRQ support
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If no one defined the rt5645->pdata.hp_det_gpio in coreboot/bios.
It will cause kernel to reboot because rt5645->pdata.hp_det_gpio
is 0. So it is worth to add a check in rt5645_jack_detect.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the codec is connected using i2c, it will only auto-increment
register addresses if msb (0x80) of the register address byte is set.
[Fixes cache sync if multiple adjacent registers are updated -- broonie]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit d74bcaaeb6 (ASoC: wm5102: Move ultrasonic response settings
lock to the driver level) created a driver local mutex for protecting
the ultrasonic response settings but neglected to initialize that mutex,
causing loud complaints from lockep and potential runtime failures. Fix
this by initializing the mutex.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
The volume blocks have an step of 0.375dB, but TLV uses 0.01dB for
units. Only use the resolution supported, ignoring the LSB of the
volume register. This results in half the steps and 0.75dB per step,
but reports accurate levels through TLV. Update the masks to reflect
that these are registers have the LSB ignored.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When trying to play a 8kHz file with codec in slave mode we get the following
error on a mx28evk:
$ aplay -Dhw:0,0 stereo_8k.wav
Playing WAVE 'stereo_8k.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo
[ 21.218647] sgtl5000 0-000a: PLL not supported in slave mode
[ 21.224559] sgtl5000 0-000a: 128 ratio is not supported. SYS_MCLK needs to be 256, 384 or 512 * fs
[ 21.233687] sgtl5000 0-000a: ASoC: can't set sgtl5000 hw params: -22
aplay: set_params:1123: Unable to install hw params:
This error happens because we are using 'sys_fs' instead of 'frame_rate' in the
valid ratio check.
Use the real'frame_rate' so that the ratio is correctly calculated and the
playback can run.
sgtl5000 codec manual states that in 'Synchronous SYS_MCLK input' mode that the
following SYS_CLK frequencies are allowed: 256*fs, 384*fs, 512*fs.
, where fs is the sampling frequency, which can be in the range of:
8, 11.025, 16, 22.5, 32, 44.1, 48, 96 kHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.
When running the codec as slave, the master should generate MCLK in the range of
256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK input mode.
In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.
Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the manual transition back to SND_SOC_BIAS_STANDBY in resume. This
is already be automatically handled by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed. While we are at it also remove the unused codec field from
the cq93vc struct so the whole probe function can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
While two of the fields in the cq93vc driver state struct are initialized
none of them are ever acutally read again. So remove the whole struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "changed" variable should be set to false at the start.
Fixes: a35daac77a ('ASoC: sigmadsp: Add support for fw v2')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
We must ensure that the clocking configuration is valid as rapidly as possible.
And do software reset before the others registers updates, or the registers
will be reset to the default state.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the patch "ASoC: rt5677: Use specific r/w function for DSP mode", the
regmap_range "rt5677_ranges" was not registered in rt5677_regmap_physical, and
it caused that the regmap_range "rt5677_ranges" cannot be accessed by the
specific r/w function. The patch fixes this issue.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch will enable ASRC for DMIC if ASRC is useable.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To use ASRC, the sysclk should be faster than 384 times sample rate of I2S1.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are 3 JD modes in RT5645. This patch configure register
values according to platform data.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/sigmadsp.c:656:1-4: WARNING: end returns can be simpified and declaration on line 636 can be dropped
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
Generated by: scripts/coccinelle/misc/simple_return.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix off by one read beyond the end of a table.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend. This makes the code a bit shorter and cleaner.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the regcache_mark_dirty()
from the suspend handler since it is already called by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the regcache_mark_dirty()
from the suspend handler since this is already done by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed. Also remove the unused codec field from the wm8903_priv
struct so we can remove the whole probe callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the extra write that sets
the WM8711_ACTIVE register to 0x00 in the suspend handler since this write
is already done when transitioning to SND_SOC_BIAS_OFF.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual asynchronous transition to SND_SOC_BIAS_STANDBY at the end of
CODEC probe() can also be removed as the core will automatically do this
after the CODEC has been probed. Also running this asynchronously has the
problem of potential race conditions with the core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. Also remove the manual sequencing back
to SND_SOC_BIAS_ON in resume as this is already handled by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to its documentation the is_powered_on_standby field of the
uda134x platform data is supposed to prevent the the driver from shutting
down the ADC and DAC in standby mode. This behavior was broken in commit
commit f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support")
almost 5 years ago and all the flag does now is cause the driver to go to
SND_SOC_BIAS_ON in probe, just for the ASoC core to put it back into
SND_SOC_BIAS_STANDBY right after probe.
Apparently the intended behavior has not been missed, so just remove
is_powered_on_standby from the platform data struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is right not left sidetone which goes to "DACR".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5fe5b767dc ("ASoC: dapm: Do not pretend to support controls for non
mixer/mux widgets") revealed ill-defined control in a route between
"STENL Mux" and DACs in max98090.c:
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACL
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACL
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACL
max98090 i2c-193C9890:00: Control not supported for path STENL Mux -> [NULL] -> DACR
max98090 i2c-193C9890:00: ASoC: no dapm match for STENL Mux --> NULL --> DACR
max98090 i2c-193C9890:00: ASoC: Failed to add route STENL Mux -> NULL -> DACR
Since there is no control between "STENL Mux" and DACs the control name must
be NULL not "NULL".
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Commit e409dfbfcc ("ASoC: dapm: Add a few supply widget sanity checks")
broke digital microphone support in max98090.c:
max98090 i2c-193C9890:00: Conditional paths are not supported for supply widgets (DMICL_ENA -> [DMIC] -> DMIC Mux)
max98090 i2c-193C9890:00: ASoC: no dapm match for DMICL_ENA --> DMIC --> DMIC Mux
max98090 i2c-193C9890:00: ASoC: Failed to add route DMICL_ENA -> DMIC -> DMIC Mux
max98090 i2c-193C9890:00: Conditional paths are not supported for supply widgets (DMICR_ENA -> [DMIC] -> DMIC Mux)
max98090 i2c-193C9890:00: ASoC: no dapm match for DMICR_ENA --> DMIC --> DMIC Mux
max98090 i2c-193C9890:00: ASoC: Failed to add route DMICR_ENA -> DMIC -> DMIC Mux
Problem is partially caused by commit f69e3caa9e ("ASoC: max98090: Enable
both DMIC channels also when using mono configuration") which connects
"DMICL_ENA" and "DMICR_ENA" supply widgets to "DMIC Mux".
Fix the breakage by reverting f69e3caa9e and then by adding additional
"DMICR_ENA" to "DMICL" and "DMICL_ENA" to "DMICR" cross-connections. This
disconnects these supply widgets from the mux and makes sure that both DMIC
data channels are still enabled together.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the device tree binding for the WM8960 codec, and modify the
driver to extract the platform data from device tree, if present.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to always convert the firmware data to local endianness before
using it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: a35daac77a ("ASoC: sigmadsp: Add support for fw v2")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To be able to read back data from the DSP parameter memory the register
range needs to be marked as readable. At the same time we do not want them
to e.g. appear in debugfs output so mark them as precious as well.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
While we are at it also replace dev_get_drvdata() with snd_soc_codec_get_drvdata().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The safeload feature allows to load up to 5 parameter memory registers
atomically. This is helpful for switching between e.g. filter settings
without causing any glitches.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the v2 version of the SigmaDSP firmware file
format. The new format has support for having different program and
parameter settings for different samplerates. In addition it stores metadata
describing the firmware. This metadata includes the set of supported
samplerates which will be used to restrict the samplerates that can be
selected by userspace. Also included is information about the modifiable
parameters. Those will be exposed as ALSA controls so they can be changed at
runtime.
The new format is based on a binary type-length-value structure that makes
it both forward and backwards compatible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The v2 file format of the SigmaDSP takes a more declarative style compared
to the imperative style of the v1 format. In addition some features that are
supported with v2 require the driver to keep state around for the firmware.
This requires a bit of restructuring of both the firmware loader itself and
the drivers making use of the firmware loader.
Instead of loading and executing the firmware in place when the DSP is
configured the firmware is now loaded at driver probe time. This is required
since the new firmware format will in addition to the firmware data itself
contain meta information describing the firmware and its requirements and
capabilities. Those will for example be used to restrict the supported
samplerates advertised by the driver to userspace to the list of samplerates
supported for the firmware.
This only does the restructuring required by the v2 format, but does not
yet add support for the new format itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The official firmware generation tool never emitted any SIGMA_ACTION_DELAY
instructions. Keeping support for it with the new restructured loader that
also supports v2 will be difficult, so drop support for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to check the version field of the firmware header to make sure to
not accidentally try to parse a firmware file with a different layout.
Trying to do so can result in loading invalid firmware code to the device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove the
wrappers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch converts the ad1980 driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the slow charge of the vref in the end of the power sequences
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the gpio naming rule to rename the irq function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many firmwares do not wait for the start bit before they begin
processing audio, whilst this is a bug on the firmware side there are
too many such firmwares in the wild to ignore the situation. This patch
moves the core enable to happen at same time as the start, the firmware
looses the ability to overlap its own startup with the audio path bring
up but we ensure that all firmwares behave.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
while building we were getting the following build warning:
Section mismatch in reference from the function rt286_i2c_probe()
to the variable .init.data:force_combo_jack_table
The function rt286_i2c_probe() references
the variable __initdata force_combo_jack_table.
This is often because rt286_i2c_probe lacks a __initdata
annotation or the annotation of force_combo_jack_table is wrong.
we were getting the warning as force_combo_jack_table was marked
with __initdata
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the ASoC core no longer needs a handle to the AC'97 device that is
associated with a CODEC we can remove it from the snd_soc_codec struct and
push it into the individual driver state structs like we do for other
communication buses. Doing so creates a clean separation between the AC'97
bus support and the ASoC core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is no longer necessary as there is no code anymore that uses this for
CODEC DAIs.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We always pass soc_ac97_ops to snd_soc_new_ac97_codec(). So instead of
allocating a snd_ac97_bus in snd_soc_new_ac97_codec() just use a static one
that gets initialized when snd_soc_set_ac97_ops() is called.
Also drop the device number parameter from snd_soc_new_ac97_codec(). We
currently only support one device per bus and all drivers pass 0 for the
device number. And if we should ever support multiple devices per bus it
wouldn't be up to individual AC'97 device drivers to pick their number, but
rather either the AC'97 adapter driver or the core code will assign them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify the default value of the MX-8E[4] to 1 for ASRC function. It could
prevent the pop noise with ASRC function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following compilation warning:
Warning: 'rt5631_i2c_dt_ids' defined but not used - when DT is not used.
Signed-off-by: Claude Youn <claude.youn@gmail.com>
Signed-off-by: Krishna Mohan Dani <krishna.md@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not free any buffers associated with writing out coefficients
to the DSP until all the async writes have completed. This patch updates
the out of memory path when allocating a new buffer to include a call to
regmap_async_complete.
Reported-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use vmalloc to allocate the buffer for firmware/coefficient download and
rely on the SPI core to split this up into DMA-able chunks. This should
give better performance and means we no longer need to manually split
the download into page size chunks to avoid allocating overly large
continuous memory regions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patah separate bias level off to standby and off. The standby
level will provide the necessary power for JD and push button
functions.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TS3A227E is an autonomous audio accessory detection and
configuration switch that detects 3-pole or 4-pole audio accessories
and configures internal switches to route the signals accordingly.
This chip also has built-in support for the new button standard
described in the Android "Wired audio headset specification" v1.0.
These buttons will be reported on the jack as buttons 0-3 mapped to
KEY_MEDIA, KEY_VOLUMEUP, KEY_VOLUMEDOWN, and KEY_VOICE_COMMAND.
This will be added as an aux_dev and have the jack passed in from the
machine driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen
5 seconds after the end of a playback.
The SMALL_POP bit should fix this, but its definition is incorrect:
according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not
bit 1.
Fix the definition accordingly and enable the bit as intended per the code
comment.
After applying this change, no loud 'click' sound is heard after playback
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch adds the ACPI match ID for rt5670/5672 codec.
So on Intel CherryTrail/Braswell platforms, the codec can be enumerated from
ACPI and depends on ACPI to get platform-specific info and power saving.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to set extra register to avoid a recording issue in TDM
mode.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver"),
the I2C part of the CS42L51 was moved to a separate file, but the
definition of the of_device_id array was left in the driver file
itself, no longer connected to the platform_driver structure using the
.of_match_table pointer.
This commit exports the of_device_id array in cs42l51, and uses it as
.of_match_able in cs42l51-i2c.c. This solution was suggested by Brian
Austin.
Fixes: a1253ef6d3 ("ASoC: cs42l51: split i2c from codec driver")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The new IPs supports a new lower frequency 768kHz DMIC operation
add support for this into the OSR control.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bard Liao