get_seconds() returns real wall-clock seconds. On 32-bit systems
this value will overflow in year 2038 and beyond. This patch changes
afs_vnode record to use ktime_get_real_seconds() instead, for the
fields cb_expires and cb_expires_at.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
get_seconds() returns real wall-clock seconds. On 32-bit systems
this value will overflow in year 2038 and beyond. This patch changes
afs's vlocation record to use ktime_get_real_seconds() instead, for the
fields time_of_death and update_at.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
In AFS, mountpoints appear as symlinks with mode 0644 and normal symlinks
have mode 0777, so use this to distinguish them rather than reading the
content and parsing it. In the case of a mountpoint, the symlink body is a
formatted string indicating the location of the target volume.
Note that with this, kAFS no longer 'pre-fetches' the contents of symlinks,
so afs_readpage() may fail with an access-denial because when the VFS calls
d_automount(), it wraps the call in an credentials override that sets the
initial creds - thereby preventing access to the caller's keyrings and the
authentication keys held therein.
To this end, a patch reverting that change to the VFS is required also.
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Flush outstanding writes in afs when an fd is closed. This is what NFS and
CIFS do.
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Handle the situation where afs_write_begin() is told to expect that a
full-page write will be made, but this doesn't happen (EFAULT, CTRL-C,
etc.), and so afs_write_end() sees a partial write took place. Currently,
no attempt is to deal with the discrepency.
Fix this by loading the gap from the server.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
When an AFS server is given an FS.FetchData{,64} request to read data from
a file, it is permitted by the protocol to return more or less than was
requested. kafs currently relies on the latter behaviour in readpage{,s}
to handle a partial page at the end of the file (we just ask for a whole
page and clear space beyond the short read).
However, we don't handle all cases. Add:
(1) Handle excess data by discarding it rather than aborting. Note that
we use a common static buffer to discard into so that the decryption
algorithm advances the PCBC state.
(2) Handle a short read that affects more than just the last page.
Note that if a read comes up unexpectedly short of long, it's possible that
the server's copy of the file changed - in which case the data version
number will have been incremented and the callback will have been broken -
in which case all the pages currently attached to the inode will be zapped
anyway at some point.
Signed-off-by: David Howells <dhowells@redhat.com>
Servers may send a callback array that is the same size as
the FID array, or an empty array. If the callback count is
0, the code would attempt to read (fid_count * 12) bytes of
data, which would fail and result in an unmarshalling error.
This would lead to stale data for remotely modified files
or directories.
Store the callback array size in the internal afs_call
structure and use that to determine the amount of data to
read.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Mode bits for an afs file should not be enforced in the usual
way.
For files, the absence of user bits can restrict file access
with respect to what is granted by the server.
These bits apply regardless of the owner or the current uid; the
rest of the mode bits (group, other) are ignored.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The group was hard coded to GLOBAL_ROOT_GID; use the group
ID that was received from the server.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
afs_fill_page() loads the page it wants to fill into the afs_read request
without incrementing its refcount - but then calls afs_put_read() to clean
up afterwards, which then releases a ref on the page.
Fix this by getting a ref on the page before calling
afs_vnode_fetch_data().
This causes sync after a write to hang in afs_writepages_region() because
find_get_pages_tag() gets confused and doesn't return.
Fixes: 196ee9cd2d ("afs: Make afs_fs_fetch_data() take a list of pages")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
In afs_writepages_region(), inside the loop where we find dirty pages to
deal with, one of the if-statements is missing a put_page().
Signed-off-by: David Howells <dhowells@redhat.com>
Pull block fixes from Jens Axboe:
"Four small fixes for this cycle:
- followup fix from Neil for a fix that went in before -rc2, ensuring
that we always see the full per-task bio_list.
- fix for blk-mq-sched from me that ensures that we retain similar
direct-to-issue behavior on running the queue.
- fix from Sagi fixing a potential NULL pointer dereference in blk-mq
on spurious CPU unplug.
- a memory leak fix in writeback from Tahsin, fixing a case where
device removal of a mounted device can leak a struct
wb_writeback_work"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq-sched: don't run the queue async from blk_mq_try_issue_directly()
writeback: fix memory leak in wb_queue_work()
blk-mq: Fix tagset reinit in the presence of cpu hot-unplug
blk: Ensure users for current->bio_list can see the full list.
Commit 88ffbf3e03 switches to using rhashtables for glocks, hashing over
the entire struct lm_lockname instead of its individual fields. On some
architectures, struct lm_lockname contains a hole of uninitialized
memory due to alignment rules, which now leads to incorrect hash values.
Get rid of that hole.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
CC: <stable@vger.kernel.org> #v4.3+
Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
When WB_registered flag is not set, wb_queue_work() skips queuing the
work, but does not perform the necessary clean up. In particular, if
work->auto_free is true, it should free the memory.
The leak condition can be reprouced by following these steps:
mount /dev/sdb /mnt/sdb
/* In qemu console: device_del sdb */
umount /dev/sdb
Above will result in a wb_queue_work() call on an unregistered wb and
thus leak memory.
Reported-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Merge 5-level page table prep from Kirill Shutemov:
"Here's relatively low-risk part of 5-level paging patchset. Merging it
now will make x86 5-level paging enabling in v4.12 easier.
The first patch is actually x86-specific: detect 5-level paging
support. It boils down to single define.
The rest of patchset converts Linux MMU abstraction from 4- to 5-level
paging.
Enabling of new abstraction in most cases requires adding single line
of code in arch-specific code. The rest is taken care by asm-generic/.
Changes to mm/ code are mostly mechanical: add support for new page
table level -- p4d_t -- where we deal with pud_t now.
v2:
- fix build on microblaze (Michal);
- comment for __ARCH_HAS_5LEVEL_HACK in kasan_populate_zero_shadow();
- acks from Michal"
* emailed patches from Kirill A Shutemov <kirill.shutemov@linux.intel.com>:
mm: introduce __p4d_alloc()
mm: convert generic code to 5-level paging
asm-generic: introduce <asm-generic/pgtable-nop4d.h>
arch, mm: convert all architectures to use 5level-fixup.h
asm-generic: introduce __ARCH_USE_5LEVEL_HACK
asm-generic: introduce 5level-fixup.h
x86/cpufeature: Add 5-level paging detection
Merge fixes from Andrew Morton:
"26 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (26 commits)
userfaultfd: remove wrong comment from userfaultfd_ctx_get()
fat: fix using uninitialized fields of fat_inode/fsinfo_inode
sh: cayman: IDE support fix
kasan: fix races in quarantine_remove_cache()
kasan: resched in quarantine_remove_cache()
mm: do not call mem_cgroup_free() from within mem_cgroup_alloc()
thp: fix another corner case of munlock() vs. THPs
rmap: fix NULL-pointer dereference on THP munlocking
mm/memblock.c: fix memblock_next_valid_pfn()
userfaultfd: selftest: vm: allow to build in vm/ directory
userfaultfd: non-cooperative: userfaultfd_remove revalidate vma in MADV_DONTNEED
userfaultfd: non-cooperative: fix fork fctx->new memleak
mm/cgroup: avoid panic when init with low memory
drivers/md/bcache/util.h: remove duplicate inclusion of blkdev.h
mm/vmstats: add thp_split_pud event for clarity
include/linux/fs.h: fix unsigned enum warning with gcc-4.2
userfaultfd: non-cooperative: release all ctx in dup_userfaultfd_complete
userfaultfd: non-cooperative: robustness check
userfaultfd: non-cooperative: rollback userfaultfd_exit
x86, mm: unify exit paths in gup_pte_range()
...
Lockdep issues a circular dependency warning when AFS issues an operation
through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem.
The theory lockdep comes up with is as follows:
(1) If the pagefault handler decides it needs to read pages from AFS, it
calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but
creating a call requires the socket lock:
mmap_sem must be taken before sk_lock-AF_RXRPC
(2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind()
binds the underlying UDP socket whilst holding its socket lock.
inet_bind() takes its own socket lock:
sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET
(3) Reading from a TCP socket into a userspace buffer might cause a fault
and thus cause the kernel to take the mmap_sem, but the TCP socket is
locked whilst doing this:
sk_lock-AF_INET must be taken before mmap_sem
However, lockdep's theory is wrong in this instance because it deals only
with lock classes and not individual locks. The AF_INET lock in (2) isn't
really equivalent to the AF_INET lock in (3) as the former deals with a
socket entirely internal to the kernel that never sees userspace. This is
a limitation in the design of lockdep.
Fix the general case by:
(1) Double up all the locking keys used in sockets so that one set are
used if the socket is created by userspace and the other set is used
if the socket is created by the kernel.
(2) Store the kern parameter passed to sk_alloc() in a variable in the
sock struct (sk_kern_sock). This informs sock_lock_init(),
sock_init_data() and sk_clone_lock() as to the lock keys to be used.
Note that the child created by sk_clone_lock() inherits the parent's
kern setting.
(3) Add a 'kern' parameter to ->accept() that is analogous to the one
passed in to ->create() that distinguishes whether kernel_accept() or
sys_accept4() was the caller and can be passed to sk_alloc().
Note that a lot of accept functions merely dequeue an already
allocated socket. I haven't touched these as the new socket already
exists before we get the parameter.
Note also that there are a couple of places where I've made the accepted
socket unconditionally kernel-based:
irda_accept()
rds_rcp_accept_one()
tcp_accept_from_sock()
because they follow a sock_create_kern() and accept off of that.
Whilst creating this, I noticed that lustre and ocfs don't create sockets
through sock_create_kern() and thus they aren't marked as for-kernel,
though they appear to be internal. I wonder if these should do that so
that they use the new set of lock keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix various iomap bugs
- Fix overly aggressive CoW preallocation garbage collection
- Fixes to CoW endio error handling
- Fix some incorrect geometry calculations
- Remove a potential system hang in bulkstat
- Try to allocate blocks more aggressively to reduce ENOSPC errors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCgAGBQJYwbgtAAoJEPh/dxk0SrTrsl8P/1cyLiDirZiUc/cToZamPTNb
cvCNuM/m7OkocB4KQ/CsHNfJDiDGPfrAJ8fukJAGXB+ordun2kM7iTx3HQ1+qEvb
pt+znR0MKgm3dCMdey8OA9UBl85GAG47jvioITUNg6/tse5u/WAaRcjISa30z/qb
xv/guqx6AYyLtQ1K5v/j67w3lmeR8b9Qu0ze7sRTn7TP3cVpFZS6TeZT/hmV/ZMp
3sG7rZFuC3c0b/b+CvyXufjDyqtIZ+yYENbmTDngyoTwOVsw66u0dZNHvV/L5RDe
z1CBKZrp+PmTIWQJeSkwX26VnOxcL0sRsfareFIYLN2fKffCFAXtbrhIifuXYe5n
a5tsyzd8jgOb6EHlKyA4Ls5o4Gqt5mUBEV1CCHVbcpSoGUMIBE3Vn7QrKjRaIGtF
1EbUI969LBjBdw2cOAYZ3bUIAW7AfGtNh6nLBTkT1n2ATOS15o+1l7yXN3HkEiGv
xyikBREp+jV8tR1ZaBNtHnPJeKYxMVAxoMw3ZfrHFA3wPbIKQwrhTZSYavrUN5YC
6/7VyLWrt4Xy8NgzHOiHtvZCAYCzP6FwBOPALrqjOMJR5giSZ7VduV3WT2v0xJO/
Cy9TsyTdjYy/dJe54KPC4jhCKkyNEGwB3VaGwifzSUcHVnYpbIBT/gDTSRNk1+xN
U2ufq3mtoi+BM8/znImL
=5WKj
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.11-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Here are some bug fixes for -rc2 to clean up the copy on write
handling and to remove a cause of hangs.
- Fix various iomap bugs
- Fix overly aggressive CoW preallocation garbage collection
- Fixes to CoW endio error handling
- Fix some incorrect geometry calculations
- Remove a potential system hang in bulkstat
- Try to allocate blocks more aggressively to reduce ENOSPC errors"
* tag 'xfs-4.11-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: try any AG when allocating the first btree block when reflinking
xfs: use iomap new flag for newly allocated delalloc blocks
xfs: remove kmem_zalloc_greedy
xfs: Use xfs_icluster_size_fsb() to calculate inode alignment mask
xfs: fix and streamline error handling in xfs_end_io
xfs: only reclaim unwritten COW extents periodically
iomap: invalidate page caches should be after iomap_dio_complete() in direct write
It's a void function, so there is no return value;
Link: http://lkml.kernel.org/r/20170309150817.7510-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently fallocate patch was merged and it uses
MSDOS_I(inode)->mmu_private at fat_evict_inode(). However,
fat_inode/fsinfo_inode that was introduced in past didn't initialize
MSDOS_I(inode) properly.
With those combinations, it became the cause of accessing random entry
in FAT area.
Link: http://lkml.kernel.org/r/87pohrj4i8.fsf@mail.parknet.co.jp
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reported-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it>
Tested-by: Moreno Bartalucci <moreno.bartalucci@tecnorama.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
userfaultfd_remove() has to be execute before zapping the pagetables or
UFFDIO_COPY could keep filling pages after zap_page_range returned,
which would result in non zero data after a MADV_DONTNEED.
However userfaultfd_remove() may have to release the mmap_sem. This was
handled correctly in MADV_REMOVE, but MADV_DONTNEED accessed a
potentially stale vma (the very vma passed to zap_page_range(vma, ...)).
The fix consists in revalidating the vma in case userfaultfd_remove()
had to release the mmap_sem.
This also optimizes away an unnecessary down_read/up_read in the
MADV_REMOVE case if UFFD_EVENT_FORK had to be delivered.
It all remains zero runtime cost in case CONFIG_USERFAULTFD=n as
userfaultfd_remove() will be defined as "true" at build time.
Link: http://lkml.kernel.org/r/20170302173738.18994-3-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a memleak in the ->new ctx if the uffd of the parent is closed
before the fork event is read, nothing frees the new context.
Link: http://lkml.kernel.org/r/20170302173738.18994-2-aarcange@redhat.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't stop running dup_fctx() even if userfaultfd_event_wait_completion
fails as it has to run userfaultfd_ctx_put on all ctx to pair against
the userfaultfd_ctx_get that was run on all fctx->orig in
dup_userfaultfd.
Link: http://lkml.kernel.org/r/20170224181957.19736-4-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Similar to the handle_userfault() case, also make sure to never attempt
to send any event past the PF_EXITING point of no return.
This is purely a robustness check.
Link: http://lkml.kernel.org/r/20170224181957.19736-3-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "userfaultfd non-cooperative further update for 4.11 merge
window".
Unfortunately I noticed one relevant bug in userfaultfd_exit while doing
more testing. I've been doing testing before and this was also tested
by kbuild bot and exercised by the selftest, but this bug never
reproduced before.
I dropped userfaultfd_exit as result. I dropped it because of
implementation difficulty in receiving signals in __mmput and because I
think -ENOSPC as result from the background UFFDIO_COPY should be enough
already.
Before I decided to remove userfaultfd_exit, I noticed userfaultfd_exit
wasn't exercised by the selftest and when I tried to exercise it, after
moving it to a more correct place in __mmput where it would make more
sense and where the vma list is stable, it resulted in the
event_wait_completion in D state. So then I added the second patch to
be sure even if we call userfaultfd_event_wait_completion too late
during task exit(), we won't risk to generate tasks in D state. The
same check exists in handle_userfault() for the same reason, except it
makes a difference there, while here is just a robustness check and it's
run under WARN_ON_ONCE.
While looking at the userfaultfd_event_wait_completion() function I
looked back at its callers too while at it and I think it's not ok to
stop executing dup_fctx on the fcs list because we relay on
userfaultfd_event_wait_completion to execute
userfaultfd_ctx_put(fctx->orig) which is paired against
userfaultfd_ctx_get(fctx->orig) in dup_userfault just before
list_add(fcs). This change only takes care of fctx->orig but this area
also needs further review looking for similar problems in fctx->new.
The only patch that is urgent is the first because it's an use after
free during a SMP race condition that affects all processes if
CONFIG_USERFAULTFD=y. Very hard to reproduce though and probably
impossible without SLUB poisoning enabled.
This patch (of 3):
I once reproduced this oops with the userfaultfd selftest, it's not
easily reproducible and it requires SLUB poisoning to reproduce.
general protection fault: 0000 [#1] SMP
Modules linked in:
CPU: 2 PID: 18421 Comm: userfaultfd Tainted: G ------------ T 3.10.0+ #15
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.10.1-0-g8891697-prebuilt.qemu-project.org 04/01/2014
task: ffff8801f83b9440 ti: ffff8801f833c000 task.ti: ffff8801f833c000
RIP: 0010:[<ffffffff81451299>] [<ffffffff81451299>] userfaultfd_exit+0x29/0xa0
RSP: 0018:ffff8801f833fe80 EFLAGS: 00010202
RAX: ffff8801f833ffd8 RBX: 6b6b6b6b6b6b6b6b RCX: ffff8801f83b9440
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8800baf18600
RBP: ffff8801f833fee8 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: ffffffff8127ceb3 R12: 0000000000000000
R13: ffff8800baf186b0 R14: ffff8801f83b99f8 R15: 00007faed746c700
FS: 0000000000000000(0000) GS:ffff88023fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007faf0966f028 CR3: 0000000001bc6000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
do_exit+0x297/0xd10
SyS_exit+0x17/0x20
tracesys+0xdd/0xe2
Code: 00 00 66 66 66 66 90 55 48 89 e5 41 54 53 48 83 ec 58 48 8b 1f 48 85 db 75 11 eb 73 66 0f 1f 44 00 00 48 8b 5b 10 48 85 db 74 64 <4c> 8b a3 b8 00 00 00 4d 85 e4 74 eb 41 f6 84 24 2c 01 00 00 80
RIP [<ffffffff81451299>] userfaultfd_exit+0x29/0xa0
RSP <ffff8801f833fe80>
---[ end trace 9fecd6dcb442846a ]---
In the debugger I located the "mm" pointer in the stack and walking
mm->mmap->vm_next through the end shows the vma->vm_next list is fully
consistent and it is null terminated list as expected. So this has to
be an SMP race condition where userfaultfd_exit was running while the
vma list was being modified by another CPU.
When userfaultfd_exit() run one of the ->vm_next pointers pointed to
SLAB_POISON (RBX is the vma pointer and is 0x6b6b..).
The reason is that it's not running in __mmput but while there are still
other threads running and it's not holding the mmap_sem (it can't as it
has to wait the even to be received by the manager). So this is an use
after free that was happening for all processes.
One more implementation problem aside from the race condition:
userfaultfd_exit has really to check a flag in mm->flags before walking
the vma or it's going to slowdown the exit() path for regular tasks.
One more implementation problem: at that point signals can't be
delivered so it would also create a task in D state if the manager
doesn't read the event.
The major design issue: it overall looks superfluous as the manager can
check for -ENOSPC in the background transfer:
if (mmget_not_zero(ctx->mm)) {
[..]
} else {
return -ENOSPC;
}
It's safer to roll it back and re-introduce it later if at all.
[rppt@linux.vnet.ibm.com: documentation fixup after removal of UFFD_EVENT_EXIT]
Link: http://lkml.kernel.org/r/1488345437-4364-1-git-send-email-rppt@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/20170224181957.19736-2-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__do_fault assumes vmf->page has been initialized and is valid if
VM_FAULT_NOPAGE is not returned by vma->vm_ops->fault(vma, vmf).
handle_userfault() in turn should return VM_FAULT_NOPAGE if it doesn't
return VM_FAULT_SIGBUS or VM_FAULT_RETRY (the other two possibilities).
This VM_FAULT_NOPAGE case is only invoked when signal are pending and it
didn't matter for anonymous memory before. It only started to matter
since shmem was introduced. hugetlbfs also takes a different path and
doesn't exercise __do_fault.
Link: http://lkml.kernel.org/r/20170228154201.GH5816@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert all non-architecture-specific code to 5-level paging.
It's mostly mechanical adding handling one more page table level in
places where we deal with pud_t.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This removes the extra include header file that was added in commit
e58bc92783 "Pull overlayfs updates from Miklos Szeredi" now that it
is no longer needed.
There are probably other such includes that got added during the
scheduler header splitup series, but this is the one that annoyed me
personally and I know about.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a reflink operation causes the bmap code to allocate a btree block
we're currently doing single-AG allocations due to having ->firstblock
set and then try any higher AG due a little reflink quirk we've put in
when adding the reflink code. But given that we do not have a minleft
reservation of any kind in this AG we can still not have any space in
the same or higher AG even if the file system has enough free space.
To fix this use a XFS_ALLOCTYPE_FIRST_AG allocation in this fall back
path instead.
[And yes, we need to redo this properly instead of piling hacks over
hacks. I'm working on that, but it's not going to be a small series.
In the meantime this fixes the customer reported issue]
Also add a warning for failing allocations to make it easier to debug.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Commit fa7f138 ("xfs: clear delalloc and cache on buffered write
failure") fixed one regression in the iomap error handling code and
exposed another. The fundamental problem is that if a buffered write
is a rewrite of preexisting delalloc blocks and the write fails, the
failure handling code can punch out preexisting blocks with valid
file data.
This was reproduced directly by sub-block writes in the LTP
kernel/syscalls/write/write03 test. A first 100 byte write allocates
a single block in a file. A subsequent 100 byte write fails and
punches out the block, including the data successfully written by
the previous write.
To address this problem, update the ->iomap_begin() handler to
distinguish newly allocated delalloc blocks from preexisting
delalloc blocks via the IOMAP_F_NEW flag. Use this flag in the
->iomap_end() handler to decide when a failed or short write should
punch out delalloc blocks.
This introduces the subtle requirement that ->iomap_begin() should
never combine newly allocated delalloc blocks with existing blocks
in the resulting iomap descriptor. This can occur when a new
delalloc reservation merges with a neighboring extent that is part
of the current write, for example. Therefore, drop the
post-allocation extent lookup from xfs_bmapi_reserve_delalloc() and
just return the record inserted into the fork. This ensures only new
blocks are returned and thus that preexisting delalloc blocks are
always handled as "found" blocks and not punched out on a failed
rewrite.
Reported-by: Xiong Zhou <xzhou@redhat.com>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
The sole remaining caller of kmem_zalloc_greedy is bulkstat, which uses
it to grab 1-4 pages for staging of inobt records. The infinite loop in
the greedy allocation function is causing hangs[1] in generic/269, so
just get rid of the greedy allocator in favor of kmem_zalloc_large.
This makes bulkstat somewhat more likely to ENOMEM if there's really no
pages to spare, but eliminates a source of hangs.
[1] http://lkml.kernel.org/r/20170301044634.rgidgdqqiiwsmfpj%40XZHOUW.usersys.redhat.com
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
---
v2: remove single-page fallback
When block size is larger than inode cluster size, the call to
XFS_B_TO_FSBT(mp, mp->m_inode_cluster_size) returns 0. Also, mkfs.xfs
would have set xfs_sb->sb_inoalignmt to 0. Hence in
xfs_set_inoalignment(), xfs_mount->m_inoalign_mask gets initialized to
-1 instead of 0. However, xfs_mount->m_sinoalign would get correctly
intialized to 0 because for every positive value of xfs_mount->m_dalign,
the condition "!(mp->m_dalign & mp->m_inoalign_mask)" would evaluate to
false.
Also, xfs_imap() worked fine even with xfs_mount->m_inoalign_mask having
-1 as the value because blks_per_cluster variable would have the value 1
and hence we would never have a need to use xfs_mount->m_inoalign_mask
to compute the inode chunk's agbno and offset within the chunk.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
There are two different cases of buffered I/O errors:
- first we can have an already shutdown fs. In that case we should skip
any on-disk operations and just clean up the appen transaction if
present and destroy the ioend
- a real I/O error. In that case we should cleanup any lingering COW
blocks. This gets skipped in the current code and is fixed by this
patch.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
We only want to reclaim preallocations from our periodic work item.
Currently this is archived by looking for a dirty inode, but that check
is rather fragile. Instead add a flag to xfs_reflink_cancel_cow_* so
that the caller can ask for just cancelling unwritten extents in the COW
fork.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
[darrick: fix typos in commit message]
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Pull timer fixes from Ingo Molnar:
"This includes a fix for lockups caused by incorrect nsecs related
cleanup, and a capabilities check fix for timerfd"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
jiffies: Revert bogus conversion of NSEC_PER_SEC to TICK_NSEC
timerfd: Only check CAP_WAKE_ALARM when it is needed
After XFS switching to iomap based DIO (commit acdda3aae1 ("xfs:
use iomap_dio_rw")), I started to notice dio29/dio30 tests failures
from LTP run on ppc64 hosts, and they can be reproduced on x86_64
hosts with 512B/1k block size XFS too.
dio29 diotest3 -b 65536 -n 100 -i 1000 -o 1024000
dio30 diotest6 -b 65536 -n 100 -i 1000 -o 1024000
The failure message is like:
bufcmp: offset 0: Expected: 0x62, got 0x0
diotest03 1 TPASS : Read with Direct IO, Write without
diotest03 2 TFAIL : diotest3.c:142: comparsion failed; child=98 offset=1425408
diotest03 3 TFAIL : diotest3.c:194: Write Direct-child 98 failed
Direct write wrote 0x62 but buffer read got zero. This is because,
when doing direct write to a hole or preallocated file, we
invalidate the page caches before converting the extent from
unwritten state to normal state, which is done by
iomap_dio_complete(), thus leave a window for other buffer reader to
cache the unwritten state extent.
Consider this case, with sub-page blocksize XFS, two processes are
direct writing to different blocksize-aligned regions (say 512B) of
the same preallocated file, and reading the region back via buffered
I/O to compare contents.
process A, region [0,512] process B, region [512,1024]
xfs_file_write_iter
xfs_file_aio_dio_write
iomap_dio_rw
iomap_apply
invalidate_inode_pages2_range
xfs_file_write_iter
xfs_file_aio_dio_write
iomap_dio_rw
iomap_apply
invalidate_inode_pages2_range
iomap_dio_complete
xfs_file_read_iter
xfs_file_buffered_aio_read
generic_file_read_iter
do_generic_file_read
<readahead fills pagecache with 0>
iomap_dio_complete
xfs_file_read_iter
<read gets 0 from pagecache>
Process A first invalidates page caches, at this point the
underlying extent is still in unwritten state (iomap_dio_complete
not called yet), and process B finishs direct write and populates
page caches via readahead, which caches zeros in page for region A,
then process A reads zeros from page cache, instead of the actual
data.
Fix it by invalidating page caches after converting unwritten extent
to make sure we read content from disk after extent state changed,
as what we did before switching to iomap based dio.
Also introduce a new 'start' variable to save the original write
offset (iomap_dio_complete() updates iocb->ki_pos), and a 'err'
variable for invalidating caches result, cause we can't reuse 'ret'
anymore.
Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Pull misc final vfs updates from Al Viro:
"A few unrelated patches that got beating in -next.
Everything else will have to go into the next window ;-/"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
hfs: fix hfs_readdir()
selftest for default_file_splice_read() infoleak
9p: constify ->d_name handling
Pull SMB3 fixes from Steve French:
"Some small bug fixes as well as SMB2.1/SMB3 enablement for DFS (global
namespace) which previously was only enabled for CIFS"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
smb2: Enforce sec= mount option
CIFS: Fix sparse warnings
CIFS: implement get_dfs_refer for SMB2+
CIFS: use DFS pathnames in SMB2+ Create requests
CIFS: set signing flag in SMB2+ TreeConnect if needed
CIFS: let ses->ipc_tid hold smb2 TreeIds
CIFS: add use_ipc flag to SMB2_ioctl()
CIFS: add build_path_from_dentry_optional_prefix()
CIFS: move DFS response parsing out of SMB1 code
CIFS: Fix possible use after free in demultiplex thread
Pull overlayfs updates from Miklos Szeredi:
"Because copy up can take a long time, serialized copy ups could be a
big performance bottleneck. This update allows concurrent copy up of
regular files eliminating this potential problem.
There are also minor fixes"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: drop CAP_SYS_RESOURCE from saved mounter's credentials
ovl: properly implement sync_filesystem()
ovl: concurrent copy up of regular files
ovl: introduce copy up waitqueue
ovl: copy up regular file using O_TMPFILE
ovl: rearrange code in ovl_copy_up_locked()
ovl: check if upperdir fs supports O_TMPFILE
Pull vfs 'statx()' update from Al Viro.
This adds the new extended stat() interface that internally subsumes our
previous stat interfaces, and allows user mode to specify in more detail
what kind of information it wants.
It also allows for some explicit synchronization information to be
passed to the filesystem, which can be relevant for network filesystems:
is the cached value ok, or do you need open/close consistency, or what?
From David Howells.
Andreas Dilger points out that the first version of the extended statx
interface was posted June 29, 2010:
https://www.spinics.net/lists/linux-fsdevel/msg33831.html
* 'rebased-statx' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
statx: Add a system call to make enhanced file info available
Pull block layer fixes from Jens Axboe:
"A collection of fixes for this merge window, either fixes for existing
issues, or parts that were waiting for acks to come in. This pull
request contains:
- Allocation of nvme queues on the right node from Shaohua.
This was ready long before the merge window, but waiting on an ack
from Bjorn on the PCI bit. Now that we have that, the three patches
can go in.
- Two fixes for blk-mq-sched with nvmeof, which uses hctx specific
request allocations. This caused an oops. One part from Sagi, one
part from Omar.
- A loop partition scan deadlock fix from Omar, fixing a regression
in this merge window.
- A three-patch series from Keith, closing up a hole on clearing out
requests on shutdown/resume.
- A stable fix for nbd from Josef, fixing a leak of sockets.
- Two fixes for a regression in this window from Jan, fixing a
problem with one of his earlier patches dealing with queue vs bdi
life times.
- A fix for a regression with virtio-blk, causing an IO stall if
scheduling is used. From me.
- A fix for an io context lock ordering problem. From me"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: Move bdi_unregister() to del_gendisk()
blk-mq: ensure that bd->last is always set correctly
block: don't call ioc_exit_icq() with the queue lock held for blk-mq
block: Initialize bd_bdi on inode initialization
loop: fix LO_FLAGS_PARTSCAN hang
nvme: Complete all stuck requests
blk-mq: Provide freeze queue timeout
blk-mq: Export blk_mq_freeze_queue_wait
nbd: stop leaking sockets
blk-mq: move update of tags->rqs to __blk_mq_alloc_request()
blk-mq: kill blk_mq_set_alloc_data()
blk-mq: make blk_mq_alloc_request_hctx() allocate a scheduler request
blk-mq-sched: Allocate sched reserved tags as specified in the original queue tagset
nvme: allocate nvme_queue in correct node
PCI: add an API to get node from vector
blk-mq: allocate blk_mq_tags and requests in correct node
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
If the security type specified using a mount option is not supported,
the SMB2 session setup code changes the security type to RawNTLMSSP. We
should instead fail the mount and return an error.
The patch changes the code for SMB2 to make it similar to the code used
for SMB1. Like in SMB1, we now use the global security flags to select
the security method to be used when no security method is specified and
to return an error when the requested auth method is not available.
For SMB2, we also use ntlmv2 as a synonym for nltmssp.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Fix two minor sparse compile check warnings
Signed-off-by: Steve French <steve.french@primarydata.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>