EC_MKBP_EVENT_SENSOR_FIFO events can be triggered for a variety of
reasons, and there are very few cases in which they should be treated as
wakeup interrupts (particularly, when a certain
MOTIONSENSE_MODULE_FLAG_* is set, but this is not even supported in the
mainline cros_ec_sensor driver yet). Most of the time, they are benign
sensor readings. In any case, the top-level cros_ec device doesn't know
enough to determine that they should wake the system, and so it should
not report the event. This would be the job of the cros_ec_sensors
driver to parse.
This patch adds checks to cros_ec_get_next_event() such that it doesn't
signal 'wakeup' for events of type EC_MKBP_EVENT_SENSOR_FIFO.
This patch is particularly relevant on devices like Scarlet (Rockchip
RK3399 tablet, known as Acer Chromebook Tab 10), where the EC firmware
reports sensor events much more frequently. This was causing
/sys/power/wakeup_count to increase very frequently, often needlessly
interrupting our ability to suspend the system.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
cros_ec_get_next_event() is documented to return 0 for success and
negative for errors. It currently returns negative for some errors, and
non-negative (number of bytes received) for success (including some "no
data available" responses as zero). This mostly works out OK, because the
callers were more or less ignoring the documentation, and only treating
positive values as success (and indepdently checking the modification of
'wakeup').
Let's button this up by avoiding pretending to handle event/wakeup
distinctions when no event info was retrieved (i.e., returned 0 bytes).
And fix the documentation of cros_ec_get_host_event() and
cros_ec_get_next_event() to accurately describe their behavior.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
This commit allows cros_ec_lpc to register a direct IRQ instead of relying
on the ACPI notification chain to receive MKBP events.
This change is done in the interest of allowing reduced jitter in the
communication path between the CrOS EC and the host for receiving sensor
data.
Signed-off-by: Enrico Granata <egranata@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Commit 57e94c8b97 caused cros-ec keyboard events
be truncated on many chromebooks so that Left and Right keys on Column 12 were
always 0. Use ret as memcpy len to fix this.
The old code was using ec_dev->event_size, which is the event payload/data size
excluding event_type header, for the length of the memcpy operation. Use ret
as memcpy length to avoid the off by one and copy the whole msg->data.
Fixes: 57e94c8b97 ("mfd: cros-ec: Increase maximum mkbp event size")
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Karlson <jekarlson@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
The cros-ec-lpc driver lives in drivers/platform because is platform
specific, however there are two includes (cros_ec_lpc_mec.h and
cros_ec_lpc_reg.h) that lives in include/linux/mfd. These two includes
are only used for the platform driver and are not really related to the
MFD subsystem, so move the includes from include/linux/mfd to
drivers/platform/chrome.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
cros_ec_i2c and cros_ec_spi drivers moved from mfd
to chrome platform.
-----BEGIN PGP SIGNATURE-----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=HNMG
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung.
Everything but the SPDX identifier updates actually came in earlier
through the MFD merge.
* tag 'chrome-platform-for-linus-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: chromeos_tbmc - fix SPDX identifier
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
-----BEGIN PGP SIGNATURE-----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=EhHj
-----END PGP SIGNATURE-----
Merge branches 'ib-mfd-4.19', 'ib-mfd-gpio-pinctrl-4.19', 'ib-mfd-i915-media-platform-4.19' and 'ib-mfd-regulator-4.19', tag 'ib-platform-chrome-mfd-move-cros-ec-transport-for-4.19' into ibs-for-mfd-merged
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
Having a 16 byte mkbp event size makes it possible to send CEC
messages from the EC to the AP directly inside the mkbp event
instead of first doing a notification and then a read.
Signed-off-by: Stefan Adolfsson <sadolfsson@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE6gYDF28Li+nEiKLaHwn1ewov5lgFAltCtRsACgkQHwn1ewov
5lhIQg//fEoZkDIjFsWIDn2WB1brLS2q7Wnv01NJR3/ZxzA29JYQ1lNA3nCM5mVS
Bf1RqPfVwIO6/d+QA5AnxLBRpRYJ7F7NKwvTvrqQ9QpFPNOLk0m7uUNYSsWTOqlA
uoReeFfJ2/UuUavd04KJRPv1ilCjoki2Wyc4lqVFSJSGZZjDWUOASAiOd666h26F
avW4qBUpJm7mmAfOFh76g6c/Jq713fJkqfdRcstRajB13oLjotfRxa/Rhxb+y8aX
RrlNz8PChIjpYTQ7yDwfLU8u5TDg2sEtz8529YaddDNBWkRyC2BIrKrkev+GIiUx
SZiPT7nmvpEOGJoPQodUa5bgE/9db7pPKb7XqUNmYQIS71jtLaOXMNje9uLn2NHo
CJtoVHJXZ9YWyODn1NPvFM28aysis14PWQGWK1HRq5PCfb8TpZ8W0QTaJV18pUBe
vdrmgxPcdnkAn0Tbt92oBiUrsVT3zoSQuLw9FPuy3ne9Oz+TKHa6kKzjcMMkynwb
mFmDhf822mfbUVkjUpNTtLJ0UMsNtd/tphDUmv1OQDRNStZS/MI4+xr23bPZbf/X
blrIjz5fM6uhUbHSKztWnntGAtzbEy75zzyhh2w99JVzJtK4UK+3ET40Kko4KUIx
1ppYa2wOJVVSvd733O8mYGmzQotKuFc5lyNozlB4EUT8ro/zW1Q=
=EhHj
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=u5Ht
-----END PGP SIGNATURE-----
Merge tag 'ib-platform-chrome-mfd-move-cros-ec-transport-for-4.19' into working-branch-for-4.19
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
There are some cros-ec transport drivers (I2C, SPI) living in MFD, while
others (LPC) living in drivers/platform. The transport drivers are more
platform specific. So, move the I2C and SPI transport drivers to the
platform/chrome directory. The patch also removes the MFD_ prefix of
their Kconfig symbols.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Original submission was GPLv2 only, so mark as GPL-2.0.
Also restored some descriptive lines that were there before.
Signed-off-by: Benson Leung <bleung@chromium.org>
Further changes from Dmitry related to the removal of platform data from
atmel_mxt_ts and chromeos_laptop. This time, we have some changes that
teach chromeos_laptop how to supply acpi properties for some input devices
so that the peripheral driver doesn't have to do dmi matching on some
Chromebook platforms.
Also adds the Chromebook Tablet switch driver, which is useful for x86
convertible Chromebooks.
Other misc. cleanup.
Thanks,
Benson
-----BEGIN PGP SIGNATURE-----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=mA72
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- further changes from Dmitry related to the removal of platform data
from atmel_mxt_ts and chromeos_laptop.
This time, we have some changes that teach chromeos_laptop how to
supply acpi properties for some input devices so that the peripheral
driver doesn't have to do dmi matching on some Chromebook platforms.
- new Chromebook Tablet switch driver, which is useful for x86
convertible Chromebooks.
- other misc cleanup
* tag 'chrome-platform-for-linus-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: Use to_cros_ec_dev more broadly
platform/chrome: chromeos_laptop: fix touchpad button mapping on Celes
platform: chrome: Add input dependency for tablet switch driver
platform/chrome: chromeos_laptop - supply properties for ACPI devices
platform/chrome: chromeos_tbmc - add SPDX identifier
platform: chrome: Add Tablet Switch ACPI driver
platform/chrome: cros_ec_lpc: do not try DMI match when ACPI device found
Move to_cros_ec_dev macro to cros_ec.h and use it when the private ec
object is needed from device object.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Celes has newer touch controller (compared to the controllers used in
older BayTrail-based devices) and so uses the same button mapping as
Samus.
This fixes the issue with mouse button being stuck in pressed state
after the first click.
Reported-by: Sultan Alsawaf <sultanxda@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
We should stop our worker thread while we're suspended. If we don't
then we'll get messages like:
cros-ec-spi spi5.0: spi transfer failed: -108
cros-ec-spi spi5.0: cs-deassert spi transfer failed: -108
cros-ec-ctl cros-ec-ctl.0.auto: EC communication failed
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
BayTrail-based and newer Chromebooks describe their peripherals in ACPI;
unfortunately their description is not complete, and peripherals
drivers, such as driver for Atmel Touch controllers, has to resort to
DMI-matching to configure the peripherals properly. To avoid polluting
peripheral driver code, let's teach chromeos_laptop driver to supply
missing data via generic device properties.
Note we supply "compatible" string for Atmel peripherals not because it is
needed for matching devices and driver (matching is still done on ACPI HID
entries), but because peripherals driver will be using presence of
"compatible" property to determine if device properties have been attached
to the device, and fail to bind if they are absent.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Replace the original license statement with the SPDX identifier.
Add also one line of description as recommended by the COPYING file.
Signed-off-by: Benson Leung <bleung@chromium.org>
Add a kernel driver for GOOG0006, an ACPI driver reporting an event when
the tablet switch status changes.
On an ACPI based convertible chromebook check evtest display tablet mode
switch changes:
Available devices:
..
/dev/input/event3: Tablet Mode Switch
..
Testing ... (interrupt to exit)
Event: time 1484879712.604360, type 5 (EV_SW), code 1 (SW_TABLET_MODE),
value 1
Event: time 1484879712.604360, -------------- SYN_REPORT ------------
Event: time 1484879715.132228, type 5 (EV_SW), code 1 (SW_TABLET_MODE),
value 0
Event: time 1484879715.132228, -------------- SYN_REPORT ------------
...
Check state is updated at resume time when different from suspend time.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Commit 001dde9400 ("mfd: cros ec: spi: Fix "in progress" error
signaling") pointed out some bad code, but its analysis and conclusion
was not 100% correct.
It *is* correct that we should not propagate result==EC_RES_IN_PROGRESS
for transport errors, because this has a special meaning -- that we
should follow up with EC_CMD_GET_COMMS_STATUS until the EC is no longer
busy. This is definitely the wrong thing for many commands, because
among other problems, EC_CMD_GET_COMMS_STATUS doesn't actually retrieve
any RX data from the EC, so commands that expected some data back will
instead start processing junk.
For such commands, the right answer is to either propagate the error
(and return that error to the caller) or resend the original command
(*not* EC_CMD_GET_COMMS_STATUS).
Unfortunately, commit 001dde9400 forgets a crucial point: that for
some long-running operations, the EC physically cannot respond to
commands any more. For example, with EC_CMD_FLASH_ERASE, the EC may be
re-flashing its own code regions, so it can't respond to SPI interrupts.
Instead, the EC prepares us ahead of time for being busy for a "long"
time, and fills its hardware buffer with EC_SPI_PAST_END. Thus, we
expect to see several "transport" errors (or, messages filled with
EC_SPI_PAST_END). So we should really translate that to a retryable
error (-EAGAIN) and continue sending EC_CMD_GET_COMMS_STATUS until we
get a ready status.
IOW, it is actually important to treat some of these "junk" values as
retryable errors.
Together with commit 001dde9400, this resolves bugs like the
following:
1. EC_CMD_FLASH_ERASE now works again (with commit 001dde9400, we
would abort the first time we saw EC_SPI_PAST_END)
2. Before commit 001dde9400, transport errors (e.g.,
EC_SPI_RX_BAD_DATA) seen in other commands (e.g.,
EC_CMD_RTC_GET_VALUE) used to yield junk data in the RX buffer; they
will now yield -EAGAIN return values, and tools like 'hwclock' will
simply fail instead of retrieving and re-programming undefined time
values
Fixes: 001dde9400 ("mfd: cros ec: spi: Fix "in progress" error signaling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Older models of Chromebooks did not describe the LPC EC in their ACPI
tables; starting with Strago-based devices Google is using GOOG0004 device
to describe EC LPC.
DMI-based match is fragile and does not work reliably, especially when
using custom firmware. It is also not needed when we can locate the right
ACPI device, so let's stop bailing out when DMI does not match but the
right ACPI device is present.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
This adds a sysfs attribute (/sys/class/chromeos/cros_ec/kb_wake_angle)
used to set and get the keyboard wake lid angle. This attribute is
present only if 2 accelerometers are controlled by the EC.
This patch also moves the cros_ec features check before the device is
added so the features map obtained from the EC is ready on time.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Add info useful for debugging USB-PD port state.
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Fixed the following checkpatch warning:
WARNING: Symbolic permissions 'S_IRUGO' are not preferred. Consider
using octal permissions '0444'.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Use DEVICE_ATTR variants for read/write attributes. This simplifies the
source code, improves readbility, and reduces the chance of
inconsistencies.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Add a define to get the cros_ec_dev from device and use it.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
When accessing a sysfs attribute, if the EC command fails, -EPROTO is
now returned instead of an error message as it is unlikely an app is
parsing the error message to do something meaningful.
Also, this patch makes use of cros_ec_cmd_xfer_status() instead of
cros_ec_cmd_xfer() so an error message is printed in the syslog.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
This patch adds generic device information to the DMI table of
the cros_ec_lpc driver, needed for Chromebooks/boxes using a
custom coreboot firmware.
The DMI info would not contain "Google_*" as BIOS version string,
instead the system vendor string would still be "GOOGLE", so this
seems to be a reasonable match for every Chromebook/box running
a custom firmware.
Signed-off-by: Salvatore Bellizzi <lkml@seppia.net>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Benson Leung <bleung@chromium.org>
Chrome platform installed a Chrome EC notify handler which prevents
default EC GPE handler getting called. Add pm_system_wakeup to the
Chrome EC notify handler so wake up from s2idle can happen.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Mark board data as __intconst/__initdata and make a copy of appropriate
entry once we identified the board we are running on. The rest of the data
will be discarded once the kernel finished booting (or module finished
loading).
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Now that Atmel driver uses generic device properties we can use them
instead of platform data when setting up touchpad on the original
Google Pixel.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Instead of passing interrupt flags via platform data to drivers, or
hoping that drivers will do the right thing and set it up the way we
need, let's set up IRQ resource and attach it to the I2C board info, and
let I2C core set it up for us.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Instead of using platform device and deferrals to handle the case when i2C
adapters appear late in the game, and not handling device unbinding all
that well, let's switch to using I2C bus notifier to get told when a new
I2C adapter appears in the system, and attempt to add appropriate devices
at that time.
In case when we have 2 Designware adapters in the system (Acer C720),
instead of counting and hoping they get enumerate din the right order,
let's switch to using their PCI devids (slot/function) that should be
stable.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Instead of trying to parse DMI IRQ data every time we try to instantiate a
device, let's do it once, when we identify the device we are working with.
This allows us to mark chromeos_laptop_get_irq_from_dmi() as __init and
discard it once module is initialized.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Instead of having separate setup() functions responsible for instantiating
i2c client for each peripheral, let's generalize the behavior and use
common code for instantiating all i2c peripherals.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
This will make code instantiating I2C device a bit clearer.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Replace the original license statement with the SPDX identifier.
Add also one line of description as recommended by the COPYING file.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
This reverts commit a376cd9160 because
chromeos_laptop instances should not be marked as "const" (at this
time), since i2c_peripheral is being modified (we change "state" and
"tries") when we instantiate devices.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Moving cros_ec_dev to drivers/mfd.
Other small maintenance fixes.
-----BEGIN PGP SIGNATURE-----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=YEO6
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung:
- move cros_ec_dev to drivers/mfd
- other small maintenance fixes
[ The cros_ec_dev movement came in earlier through the MFD tree - Linus ]
* tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: Use proper protocol transfer function
platform/chrome: cros_ec_lpc: Add support for Google Glimmer
platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing.
platform/chrome: cros_ec_lpc: remove redundant pointer request
cros_ec: fix nul-termination for firmware build info
platform/chrome: chromeos_laptop: make chromeos_laptop const
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
pkt_xfer should be used for protocol v3, and cmd_xfer otherwise. We had
one instance of these functions correct, but not the second, fall-back
case. We use the fall-back only when the first command returns an
IN_PROGRESS status, which is only used on some EC firmwares where we
don't want to constantly poll the bus, but instead back off and
sleep/retry for a little while.
Fixes: 2c7589af3c ("mfd: cros_ec: add proto v3 skeleton")
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Brian Norris